Search Documents

By James M. Tantalla, Dwight Metcalf, Roderic A. Ellman Jr.

"The construction of a new low head hydro-electric plant at the Cannelton Lock and Dam required the design and construction of a cofferdam to accommodate a deep excavation extending approximately 150 feet below the Ohio River levels. The new plant, which generates about 390 GWh of electricity annually, is owned by American Municipal Power (AMP). A specialist team was assembled to design and construct the cofferdam, marine dike and CB slurry wall that helped make the project successful and on time for project delivery.Because the new plant diverts water from the locks and dam through a powerhouse to generate power, it would need to be partially in the river to operate properly. To accomplish this, approximately 250,000 square feet of land was reclaimed from the river by construction of a marine dike. The dike, combined with the design and construction of a 150 foot deep cement bentonite (CB) cutoff wall enabled construction of the new plant in the dry. Extensive dewatering analyses were performed using Modflow to evaluate pumping requirements and the number of wells needed to maintain ground water at required levels within the side slopes and final subgrade. A monitoring program consisting of inclinometers, piezometers and movement monitoring points were used to monitor cofferdam stability and performance throughout construction. Detailed two and three dimensional stability analyses that included a parametric study of fluctuating river levels and slurry unit weight were performed to ensure stability and suitable low permeability of the trench during cut-off wall excavation both on land and in the marine dike. The wall was constructed with both a hydromill excavating primary panels and a clamshell following behind to construct secondary panels. Data acquisition systems onboard the excavating equipment allowed for detailed confirmation of the continuity of the wall at each interface between panels. Another challenging aspect was the CB mix design for the trench. The cofferdam required the construction of a 1,300-foot long marine dike downstream of the existing dam up to 100 feet tall founded on existing river sediment to enclose the site and cut-off the seepage into the excavation from the river. Marine dike construction utilized vibro-compaction to pre-densify granular fills placed underwater through which the CB trench extended."

Jan 1, 2016

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

The demand for renewable energy is growing as the conventional energy resources are becoming more limited and we are more conscious about the negative impact of conventional energy sources on the environment. Wind turbines technology is evolving in a fast pace, the towers are becoming taller, and the rotors are getting larger. The challenge is to maintain the Levelized Cost of Electricity (LCOE) as low as possible to ensure a sustainable and an economically feasible energy supply. Thus, the foundation systems for wind turbines should evolve to meet the increasing load demand, while reducing the LCOE. In this paper, an innovative foundation system for onshore wind turbines is presented. The new foundation system is the conventional P&H tensionless pier foundation (PHTP) with a reinforced concrete collar at the top of the pier. 3D FEM modeling was conducted to assess the benefits achieved by adding a collar at the top of the PHTP foundation. The numerical results show a significant performance enhancement of the proposed foundation system over the conventional PHTP foundation. The enhanced foundation system also has an economical advantage because the depth of the pier can be greatly reduced while maintaining a superior performance.

Sep 8, 2021

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By Rakam Lama Tamang, Michael J. Byle, Stephen Ernst

"For various reasons, dredging may become necessary in front of existing bulkhead walls, either for channel deepening or for environmental remediation of contaminated sediments. The removal of sediments at the base of bulkhead walls removes support for the toe of the wall that must be assessed. Evaluation of this impact can be problematic for aging bulkheads for which no design or construction records exist. This paper will address the steps that should be taken in investigation and analysis to assure proper assessment and means to address uncertainties and gaps in information. The steps include pre-investigation data review, field inspection, geotechnical and geophysical investigation tools, parametric analysis and design tools. Examples from several bulkhead assessment projects will be provided that include a variety of conditions and tools for application. The focus of the paper will be on the integration of technologies to assess bulkhead geometry, geotechnical properties and stability, structural safety and constructability issues with removal of support, and means of temporary and permanent stabilization for environmental applications.IntroductionBulkheads and quays have existed as long as there have been waterfront activities. Some of the earliest date back to 1200 B.C.E.(Raban, 1987), however in the United States few predate the eighteenth century. Most extant bulkhead structures, and all steel sheet pile bulkhead walls date from the early 20th century or later. These structures function to protect the shore from erosion, support landside activities, and serve as place to moor and offload vessels. Regardless of the age or usage of existing bulkheads, it is essential to assess and protect them if needed where removal of soils on the water side of the bulkheads is planned to dredging.Waterfront BulkheadsExisting bulkhead structures can be classified into two types: Cantilevered, and anchored. Cantilevered walls are completely supported by the soil on the water side, while anchored bulkheads are supported both by the soil on the water side and anchorage on the land side (Figure 1). Walls may be constructed of timber, steel, or concrete. Timber walls may be lagging with soldier piles, cribbing with soldier piles, or timber sheeted such as Wakefield walls (Figure 2). Steel bulkheads are most commonly constructed using sheet piling comprised of interlocking A or Z shapes, though some historic walls were constructed with flat sheets. Precast concrete sheet piling has also been used in construction of bulkhead walls. Anchorage may be provided by steel bars or tendons attached to deadmen, sheet piling, driven piles, or earth anchors."

Jan 1, 2017

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Balasubramani M., Ramana P. V., Bairagi K.

This paper is a case study of an earthen Cofferdam, constructed for a deep excavation at Intake location in river Aaundha, Maharashtra, India. A 12 m (39 ft) deep excavation was made to construct the Intake well. The natural soil profile at this location is clay followed by rock. An earthen Cofferdam of maximum height 7 m (23 ft) was made around the periphery of the excavation. Cofferdam embankment and excavation slopes were analyzed using the finite element software PLAXIS-2D. Clayey sand was proposed as filling material during design, but clayey soil was used for the embankment formation during execution. The embankment was built up to 5m height in July 2017 and completely submerged due to monsoon. In February 2018 embankment height raised to 7m (23 ft) by filling the soil over the existing submerged embankment. After a few days of completion of the Cofferdam construction, the inside slope of the embankment had started sliding due to continuous dewatering. The design and execution of deep excavation with earthen Cofferdam for waterfront structures are challenging. The selection of filling material for embankment formation and dewatering techniques plays a vital role in the safety and stability of the embankments. Although all the safety measures were taken during the design, execution challenges are unpredictable.

Nov 1, 2022

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Steve Davidow, Ashely E. Evans, Peter M. Kandaris

"Annually thousands of deep foundations are constructed across North America supporting high voltage transmission line structures. However, a recent state of the practice survey by the Deep Foundation Institutes’ Electric Power Systems Foundation Working Group discovered that the electric power utility industry lacks consistent foundation design guidelines. The survey identified a wide variability in design assumptions, a minimal understanding of risk based analysis, and a need to standardize design methodologies. This paper summarizes the state of practice in electric system foundation design and proposes a framework for risk-based foundation design by accounting for uncertainty from both loads and resistances. Loads derived from electric system codes do not necessarily provide a compatible level of reliability for the design of foundations, as they are a mixture of probabilistic and deterministic values. Load uncertainty is derived from variability in weather conditions, structural models and material properties, typically accounted for by code derived overload factors. Resistance uncertainty arises from variability in natural soil properties, resistance models, subsurface construction techniques, material sampling methods, and limited observations. A consistent methodology is offered relating nominal resistance capacity (strength) to structure loads and service state criteria. Discussion also includes the need for risk-based assessments to account for non-structure load influences (fluvial loads, scour ground loss, liquefaction, etc.).INTRODUCTIONNearly 40 years ago the Electric Power Research Institute (EPRI) embarked on a major research effort to optimize reliability and economics of transmission line foundation design. Strategies focused on improvements in design models, site characterization, exploration strategies and testing to reduce uncertainty and variance in analysis. Transmission line engineers realized that safety and reliability advancements in design based on probabilistic approaches, with a focus on the unique nature of transmission line, could better control risk and cost.Some transmission line professionals took full advantage of these advancements, particularly where research led to improved software and models. Yet, even after two decades of extensive research, by 1995 the industry still had made little progress in changing design habits. The majority of designers were still characterizing sites via deterministic methods, using loads that may or may not relate to a consistent probability of occurrence, and applying a traditional global factor of safety approach (Phoon, et al. 1995). The following two decades have seen even greater developments in software and reliability-based analysis methods, but old habits seem to die hard as recent surveys show less than half of design professional quantitatively assess risk in their design process."

Jan 1, 2017

By Filippo Maria Leoni, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed to reduce flood damages in the City of New Orleans and surrounding parishes, the SELA-22 project entailed the construction of a concrete covered canal along Jefferson Ave. and Prytania Street. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate under-seepage, thus creating a so called bottom plug, and provide structural support for the concrete box culvert. The U.S. Army Corps of Engineers (USACE), New Orleans District, selected the jet grouting technology for the construction of the bottom plug to a maximum depth of approximately 40 ft, and for a total length of approximately one mile. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid jet grout technology which, by limiting the overlap between adjacent columns, allowed a reduction of the overall number of installations. Approximately 2,400 elliptical jet grout columns were installed in a very challenging environment, especially under a logistical point of view. This paper will summarize the main features of the project, focusing on the innovative technological solution adopted to maximize productivity and on the several challenges faced in such limited and complicated logistical conditions.INTRODUCTIONThe Southeast Louisiana (SELA) drainage program has been designed with the purpose of reducing flood damages in the City of New Orleans and surrounding parishes. This will be accomplished by constructing new pumping stations and better drainage canals throughout. The program was authorized in 1996 by the United States Congress and administered under a project cooperation agreement between the Sewerage and Water Board of New Orleans (SWBNO) and the USACE.Prompted by the severity of damages associated with rainfall flooding in southeast Louisiana, the SELA program consists of several individual project components. The proposed work is located on both the east and west banks of the Mississippi River in the Orleans and Jefferson Parishes, as well as in portion of St. Tammany Parish."

Jan 1, 2017

By Timothy Nelson, Simon Burnworth

"The University of California’s new Berkeley Art Museum and Pacific Film Archive will showcase a collection of art and film in a facility that pairs an existing 1930s-era printing press facility with a new, architecturally unique auditorium wing. The centerpiece of this adaptive-reuse project is the existing 3- story art-deco Administrative Building, which will be integrated into the new museum and provide approximately 18,000 square feet of usable space. Degenkolb Engineers, as the shoring engineer of record, along with Condon Johnson & Associates Inc., the shoring contractor, worked together with general contractor Plant Construction Company to design and build a temporary structure to facilitate the complex retrofit, renovation, and expansion of the Admin Building. This paper will discuss the challenges faced by the design and construction team, the sustainable solutions implemented on the project, and the collaboration between teams to meet the unique constraints of the project and the site.INTRODUCTION AND PROJECT BACKGROUNDThe Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California Berkeley (UCB) campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home."

Jan 1, 2017

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram, Abraham Varghese

"Geotechnical investigation for the Kochi Metro revealed a critical section of the Viaduct near Ernakulam Junction Railway Station. Four piers, located over a 220 m stretch, were passing through an area with substantial thickness of soft clay. The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear test was conducted at different depths in addition to the routine SPT. The design of heavily loaded piles in such strata is a challenge due to the liquefaction of the shallow sands and negative skin friction / down-drag in the soft under-consolidated clay. Bored cast-in-situ piles of 1500 mm diameter extending to 50-60 m depth were used to carry 500-600 tonnes load.INTRODUCTIONThe first phase of the rapid transit system at Kochi, Kerala (See Fig. 1) whose elevated route spans from Aluva to Thripunithura covers a total distance of about 25 kilometers. One of the more critical sections of the viaduct exists near the Ernakulam Junction Railway station where the alignment takes a sharp curve to move towards Vyttila, crossing the railway tracks and running partially over the approach of South over-bridge.In this section, four piers located on either side of the railway tracks near the Route Relay Cabin of Ernakulam Junction Railway Station pass through an area with substantial thickness of soft underconsolidated clay.The alignment is geotechincally challenging due to the presence of loose liquefiable sand and soft underconsolidated and sensitive clay.Initial investigations by the owner based on limited boreholes only yielded conservative and inconclusive pile capacities. For a thorough understanding of the soil behaviour, a detailed geotechnical investigation was carried out to assess the engineering behaviour of the soil strata.The scope of the geotechnical investigation included two boreholes and a static cone penetration test at each pier location. In the boreholes, field vane shear tests were conducted at different depths in addition to the routine SPT."

Jan 1, 2015

By Jeffrey Goodwin P. E., Melih Demirkan Ph. D. P. E., Kevin Tehansky P. E.

Just an hour drive down MD 301 from National Harbor, construction to replace the Governor Harry W. Nice Memorial/Senator Thomas ‘Mac’ Middleton Bridge (HNB) began in spring of 2020. The Maryland Transportation Authority (MDTA) contracted with Skanska-Corman-McLean (SCM) to deliver a new US 301 bridge spanning 1.9 miles from Maryland to Virginia over the Potomac River aiming to improve capacity, safety, and access of the roadway. The project area presented a geotechnical design challenge due to the installation of new bridge foundations in the problematic soils of the Atlantic Coastal Plain alluvial deposits. With the existing bridge remaining in service during construction, and the site’s logistical constraints placing new pile driving operations near existing abutments and piers, a complex instrumentation and monitoring plan was developed to ensure public safety throughout the project. This paper discusses the geological conditions of the project area, the collaborative approach of various design team members to develop an appropriate monitoring plan utilizing various instrumentation, an understanding of baseline conditional movements of the existing bridge, and impact response of adjacent construction activity to help deliver effective new bridge foundations while protecting the old ones.

Oct 1, 2022

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

The city of Naruto in the southwestern part of Japan is situated at the mouth of the mighty Yoshino River. An approximately 1,000m-long levee/bulkhead along one of the river’s tributaries in the city was raised with prefabricated steel panel walls on a concrete base bulkhead. Some sections of the walls’ foundations were combi-walls made of sheet pile cut-off walls and interspaced pipe piles; both of which were installed with press-in piling because the new wall alignment was very close to existing homes and businesses. A Clamp Crane, which clamped onto already installed piles and moved forward and backward on them, was utilized for a segment where the access to its piling location was too tight for a conventional crane or a track-mounted pile driver to maneuver.

Sep 8, 2021

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By Joel B. Dellaria, Justin R. Lewis

"No. 9 Walton is a new high-rise condominium building located in the Gold Coast area of Chicago. The adjacent building, Walton on the Park, featured 4 levels of below grade parking and utilized a secant pile wall with integral drilled shafts to support the exterior columns. The earth retention system (ERS) for No. 9 Walton also employed a secant pile wall in combination with drilled shafts. The excavation into the soft Chicago clays varied in depth from 9.75 m to 12.5 m (32 feet to 41 feet) below grade. The temporary excavation support used internal braces from the new secant piles to the existing foundation system of Walton on the Park to provide earth retention. Engineering teams for both projects worked together to design the bracing scheme and connections to ensure that the new excavation and internal bracing would not overstress any elements of the existing structure. Further complicating the project, immediately to the west of the project was a historic church founded on shallow spread footings which required underpinning to minimize movements.The project involved three different building owners, small values for acceptable wall movement, an extensive monitoring program and the challenges of merging two earth retention systems. The subsurface conditions at the site, the adjacent structures, the excavation, and the performance are described. A summary of the design methods and the expected movements of the ERS are discussed, and the performance monitoring system is described. Overall, the ERS performed better than expected with less than 1 inch of measured lateral wall movement during and after the excavation was completed. Measured performance of the ERS is compared to the predicted performance and to the performance requirements for the project.INTRODUCTIONNo. 9 Walton is a new high-rise condominium building in Chicago located in the Gold Coast. The building has 3 levels of below grade parking and 36 levels of living space above grade. Developers originally slated the project to be Phase 2 of the Walton on the Park development built in the mid 2000’s, using portions of the existing foundation system for development of the new structure. However, the housing market crash in 2007 prompted cancellation of Phase 2 of the Walton on the Park development. The property sat undeveloped until 2015 when design and construction for No. 9 Walton began under a new development and design team. The project team completed foundation excavation and below grade structures in 2016 with the first units of the building turned over to new homeowners in 2017.The structural design for No. 9 Walton consisted of reinforced concrete columns and slabs, supported laterally by a heavily reinforced concrete central core. Drilled shafts to rock supported the interior columns and core with the exterior columns and foundations integrally included in the earth retention system. The structure had a below-grade footprint of approximately 1,490 m2 (16,000 ft2). The general excavation extended 9.75 m to 12.5 m (32 feet to 41 feet) below street level with the deepest portions at the central building core mat foundation."

Jan 1, 2017