Search Documents

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By B. Crane, S. Schwartz

"IntroductionThe Cape Breton Development Corporation (CBDC) located in Cape Breton, Nova Scotia, in eastern Canada, was established in 1967. Its mandate at that time was to facilitate a phased downsizing of the coal industry and developing viable replacement industries. The oil crisis in the early 1970s changed CBDC’s mandate and focus was modified to increase coal production to support Nova Scotia Power Commission’s “off oil” policy for their power generators. In the late 1980s the mandate to develop viable replacement industries was eliminated and CBDC became primarily a coal mining company. CBDC presently operates two underground coal mines, Phalen Colliery and Prince Colliery, using a retreat longwall method of mining. Both mines operate beneath the Atlantic Ocean. CBDC also operates associated infrastructure — central workshops, a railroad, coal preparation plant, and international pier. The Need For Substantial ChangeOver the last few years, CBDC has been facing some challenging issues, including improving labour management relations and achieving financial self-sufficiency and profitability. Recent achievements with regard to human resource issues, especially in the areas of collective bargaining, absenteeism, and attendance, show noticeable improvements. All participants should be commended for successfully concluding the collective bargaining process with all four CBDC unions, CUPE; CAW; IAM&AW; and UMWA. However, although these changes are encouraging, even critical in the short term, they are not sufficient to ensure the long-term viability of the company. Market ForcesShort- and long-term financial realities are drawing the need for further substantive changes. The corporation has a mandate to achieve financial self-sufficiency by the year 1999. This goal can only be achieved through a combination of cost reductions and productivity gains, specifically, a reduction in the workforce of 658 and an increase in production of 800 000 tonnes annually. This increase in productivity requires CBDC to re-think the way it does things.In the longer term, CBDC faces even greater challenges. The energy market is becoming more competitive. The electrical utilities across Canada are anticipating deregulation and are positioning themselves for the resultant competition. As primary fuel supplier to Nova Scotia Power Inc. (NSPI), the corporation will have to become ever more competitive to stay in business."

Jan 1, 1997

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

By A. H. Mumin, A. K. Somarin, K. S. Oran

"Synvolcanic structures played a fundamental role in the genesis, morphology, and siting of volcanogenic massive sulfide ores and associated hydrothermal alteration in the Archean South Sturgeon Lake caldera complex. The most voluminous and persistent hydrothermal venting and massive sulfide deposition occurred along synvolcanic rifts and grabens associated with faults and tectonic fissures that created permeable fracture zones deep enough to access the underlying hydrothermal reservoir. The type of fracturing is highly variable and changes with the composition, competency, degree of consolidation, and alteration of host rocks. Synvolcanic structures and fracture styles also vary according to the amount and type of tectonic movement, including extension-related collapse, shearing and faulting perpendicular to the principal direction of extension, and orthogonal faulting and shearing. Permeable conduits were created by tension fracturing along fault zones, brittle deformation at the intersections of orthogonal faults, and by extensional fractures in stockworks. In texturally uniform footwall rocks, the distribution of alteration zones was controlled by the morphology of the structural conduit. In rocks with vertical and/or lateral facies, permeability, and competency changes (e.g., Lyon Lake graben), there was an additional stratigraphic control over fluid migration. Some crosscutting synvolcanic structures, alteration zones, and intrusions appear as stratiform units at the present erosion surface due to regional deformation and the present attitude of the volcanic stratigraphy.Hydrothermal mineral assemblages (e.g., quartz, carbonates, chlorite, pyrite, chalcopyrite) infilling structurally induced fractures provide good evidence of fluid migration pathways. However, mineralogy can vary significantly according to the fluid characteristics, host rock geochemistry, and subsequent metamorphic history of the area.Clearly, one of the best methods for locating volcanogenic massive sulfide deposits is to delineate the attitudes of synvolcanic structures, and explore those that show evidence of associated high-temperature hydrothermal mineral assemblages. Excellent exploration targets occur where synvolcanic structures with hydrothermal alteration intersect paleo-seafloor horizons."

Jan 1, 2007

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By Clifford Britch

"Kaiser Resources Ltd. has completed feasibility studies resulting in approval of $277,500,000 for the construction of the Greenhills Surface Coal Mine, located 35 km north of Sparwood, B.C. The mine is designed to produce 1,800,000 tonnes per year of metallurgical coal over a 20-year period by conventional truck /shovel methods.The project is in the detailed design phase, with some preparation work being carried out on the site. The major construction activities are scheduled to commence in the spring of 1981. Mine development and pre-stripping will commence in July 1981, with first coal production scheduled for mid 1983.This paper will be a general description of the project and will include a discussion of the geology, reserves, mine planning, coal handling and processing, surface facilities and related topics.IntroductionProject DefinitionThe Greenhills Project is designed to produce, by conventional truck I shovel surface mining methods, 1,800,000 clean tonnes of metallurgical coal per year for twenty years . The production/ life constraints were chosen as being meaningful for planning and evaluation purposes after appraisal of the market potential and are not limited .by economic reserves. Substantial additional strippable reserves are available which would facilitate expansion of the proposed mine life and/ or capacity. In fact , all the facilities are designed so that they can be expanded in the future to accommodate a doubling of annual coal production, and certain portions of the coal processing facilities are being installed with an annual capacity of 3,600,000 tonnes. The mine will also produce approximately 2,400,000 clean tonnes of oxidized thermal coal, mostly in the first decade."

Jan 1, 1981

By J. J. Bouillon

"Located in the northwestern portion of the Abitibi greenstone belt, Les Mines Selbaie is a copper-zinc (silver and gold) producer. Felsic tuffs host three are zones. Composed of sulphide veins and breccias, they are not exhalative massive sulphide deposits, except, probably, for the massive pyrite (fragments and lenses) localized close to the top of the volcanic sequence.The total of all (mineable and mined) ore in the three zones presently outlined on the property, is of the order of 29.9 x 106 tonnes with average grade of 0.63 g/t Au, 37.02 g/t Ag, 1.21% Cu, 1.91% Zn.The ore reserve calculations and the daily production procedures are computerized to various degrees. The data handling process is highly computerized.Various geophysical methods are, and have in the past, been successfully used on the property. The ""mise-à-la-masse"" surveys were used to perform the geological interpretation of an underground deposit (A-2 zone). Presently the PULSE-EM surveys are performed in all surface and underground exploration drill holes."

Jan 1, 1990

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

By P. Latostenmaa, O. Forsén, M. Lundström, J. Aromaa

The history of electrolytic copper production in Finland is closely connected with the industrialization of Finland and events of the Second World War. Production of cathode copper by electrowinning from the processing of Outokumpu ore started in 1913 based on the Hybinette nickel process, however due to the poor performance of this process, the plant was closed in 1929. Outokumpu commenced copper smelting at Imatra in eastern Finland in 1936 producing blister copper for refining outside the country. Due to the threating military situation, a new electrolytic copper refinery was built in 1941 at Pori in western Finland to refine the anodes. This was the first electrolytic copper refinery in Finland. It was built with 108 cells having a capacity of 12,000 tonnes/y. In addition, the smelter was relocated to nearby Harjavalta in 1944–1945. To fulfill the war reparations included in the peace treaty with the Soviet Union, a doubling of the smelter capacity was realised, with the Pori refinery capacity increasing to 20,000 tonnes/y in 1946 by adding additional cells. The cornerstone of Finnish metallurgical technology — Outokumpu flash smelting — was invented with the new technology commissioned at Harjavalta in 1949 replacing the electric furnace and providing a further increase in copper output with subsequent enlargement of the refinery. By 1963, the plant consisted of 380 cells with a capacity of 48,000 tonnes/y of cathode copper. The Pori electrolytic copper refinery has operated continuously since 1941. Commencing in 2004 the Pori refinery has been part of the Boliden group of Sweden. The most recent plant upgrade was in 2007 with the installation of permanent cathode technology. In 2017, the production of the Pori refinery was 133,000 tonnes of copper cathode, 2,300 tonnes of nickel sulphate, along with 66 tonnes of silver and 4.6 tonnes of gold. This paper describes these outstanding achievements. INTRODUCTION In 1809 the Kingdom of Sweden was defeated by the Russian Empire in the Finnish War, and Finland was annexed by the Russian Empire as the autonomous Grand Duchy of Finland. Finland’s commercial and industrial interests were developed to serve the Empire’s needs. Finland had raw materials, but at the start of the 20th century Finnish industry was based on the use of wood as raw material and agricultural products. The mining industry was only a few percent of the country’s industrial production.

Jan 1, 2019

By S. Mostaghel, V. Hernandez, S. Ge

"The automotive industry is under a constant pressure to reduce the weight of vehicles in order to reduce emissions and improve fuel efficiency. As such, there is an ever-growing demand for high strength and high ductility steel grades to meet the need for lightweight automotive components. Over the past decade, the production and application of 2nd and 3rd generation Advanced High Strength Steels (AHSS) as a lightweight material in automobiles has gained significant popularity due to their exceptional mechanical properties. However, the production cost of these high manganese steel remains high, partially due to the need of large amounts of ferromanganese as alloying material in standard steelmaking processes.The current study introduces a new and cost-effective technology for the production of medium- and high-manganese steels, where self-fluxed micro-pellets of manganese ore will be used as the source of manganese that can be injected into the steel bath. Prior to injection, these pellets are subjected to a pre-reduction process using a mixture of H2 and CO gases, where partial metallization of iron and manganese will occur. Direct injection of the pre-reduced micro-pellets provides less volatilization/emission and higher recovery of manganese, and is capable of producing AHSS with 6–18 wt% Mn.INTRODUCTIONAutomakers are constantly searching for lighter, stronger and cheaper materials in an effort to create safer and more fuel efficient vehicles. The introduction of aluminum alloys and polymer composite materials for automotive applications has been carving into what is traditionally one of the most profitable markets of the iron and steel business. The steel industry responded with Advanced High Strength Steel (AHSS)—a family of manganese containing steels which exhibit exceptional strength and ductility."

Jan 1, 2016

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By E. Henry, C. Mayer, H. Rott

Hangingwall deformation monitoring at Kiruna mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening toward the town of Kiruna. In the quest for more effective monitoring techniques, LKAB decided to evaluate the ability of satellite-borne synthetic aperture radar (SAR) interferometry to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the mining industry. This paper describes the basic principles of SAR interferometry and describes how subsidence is monitored at Kiruna mine. The encouraging results are discussed as well as the benefits (continuous deformation mapping, low cost, fast, etc.) and limitations (sensitivity to snow and vegetation cover) of the technique.

Jan 1, 2004

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By W. K. Gowans

The Sullivan Concentrator treats a complex sulphide ore consisting mainly of galena, marmatite and pyrrhotite. The ore carried minor values in silver, antimony, bismuth, indium and tin. The products of the concentrator are lead, zinc, iron and tin concentrates. The minor metal values other than tin are recovered from the concentrates by the refining processes in the smelter at Trail.The concentrator was completed in 1923 and first operated with a capacity of 2,500 tons per day. In the years 1926 to 1929 changes to equipment and buildings brought the operation up to 5,500 tons per day and then, in the years 1935 to 1945, the daily tonnage was raised to 8,500 tons. After 1945, the rising insoluble content of the ore made it necessary to consider the construction of a Sink-Float plant. At this time consideration was also given to the construction of a new crushing plant underground to replace the rolls crushers and cone crushers located at the concentrator. By 1949, construction of the Sink-Float plant was completed along with a new underground crushing plant, and an electric haulage way between the underground crushing chamber and the Sink-Float plant. The ore was hauled in forty 14-ton car trains which discharged into a 3,000 ton receiving bin by means of an air operated five car rotary dumper. With the start up of the,Sink-Float plant, a 1 ½ ft. by 12 ft. Hardinge rod mill was also brought into operation. The Sink-Float plant made it possible to treat 12,000 tons/day of mine run ore with up to 40% of this being rejected as float.

Jan 1, 1975

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By M. F. Lopez, A. J. Mattus, S. B. Magid, D. B. Mobbs

"The use of Caro's acid as a replacement for hydrogen peroxide for the oxidation of vanadium prior to solvent extraction resulted in a 56% reduction in oxidant usage when compared on an equivalent hydrogen peroxide basis. Comparative oxidation tests, using two actual uranium mill raffinates, resulted in premature precipitation of an amorphous ferric vanadate when hydrogen peroxide was used to oxidize one of the raffinates containing a high iron to vanadium ratio. The use of Caro's acid eliminated the precipitation problem, thereby permitting the adjustment of the raffinate pH to a higher, more favourable level prior to solvent extraction.Potentiometric characterization of the raffinates revealed that vanadium is responsible for the inefficiency of hydrogen peroxide compared with Caro's acid, with the oxidation efficiency of iron being the same for both oxidants. A limiting potential between 720 and 740 mV was observed when using hydrogen peroxide, while, when using Care's acid, potentials approaching 1200 mV were achievable.A four-stage, countercurrent extraction performed on the oxidized raffinates did not reveal any operational problems. The extraction efficiency and the extraction coefficient were found to be higher when Caro's acid was used as the oxidant, as opposed to hydrogen peroxide.IntroductionMost vanadium is recovered as a by-product of some other process: leaching of Carnotite uranium ores, oil fly ash, phosphate rock or chromite processing. The major source of vanadium has been from uranium mills incorporating acid leaching of Carnotite ore s at elevated temperatures and pressures. The by-product recovery of vanadium from uranium ores of the Uravan Mineral Belt, located in the Colorado Plateau , is a common occurrence when vanadium recovery is economically viable."

Jan 1, 1983

By D. Gendzwill, N. Martin

"In early 1987, the Patience Lake potash mine near Saskatoon, Saskatchewan, was closed due to uncontrollable floodingWater inflows were first encountered during routine mining in 1975 at the south boundary of the mine lease. Underground grouting and construction of bulkheads limited the flo but did not completely stop it. Subsequent seismic surveys showed that the mine had approached the edge of a large collapse structure in which the salt and potash had been partly dissolved and removed by groundwater.In 1986, the small flow into the mine started to grow. Despite renewed grouting, the flood increased and outstripped pump capacity. The grouting program temporarily slowed the inflow but was unable to stop it. Eventually, from seismic and drilling evidence, it became clear that the water source was an extensive system of vertical fractures which would be impossible to seal by drilling and grouting from underground. A new plan to install 14 bulkheads underground would have sealed the water source from the rest of the mine but the construction program could not be completed before rapidly increasing inflow threatened to fill the mine. The underground mine was closed and a new solution mine started in 1988."

Jan 1, 1996