Search Documents

By Steven R. McCutcheon

ABSTRACT - The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No . 12, with total reserves (including past production) of 148 million tonnes grading about 12.50% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz ( ± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeochemistry of !east altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary sig­ nature. The two types can be distinguished on the basis of total alkalies (Na2O + K2O) versus SiO2/Al2O3, and Ti02 versus Fe/(Fe+ Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies (lacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal­ bearing fluids and cold seawater. High Fe/(Fe+ Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophically from an acquifer in the footwall stratigraphy.

Jan 1, 1992

By Hans de Ruiter

"Delft University of Technology, RWTH Aachen, Helsinki University of Technology and Imperial College established the Federation of European Mineral Programs (FEMP) in 1999 as a legal body to coordinate joint M.Sc. education.By 2003 the number of participating universities in Europe has grown to 9 (in 7 countries) offering 3 different M.Sc. joint programs. Furthermore students from 8 universities in the USA, Canada, Australia and Chile participate through exchange agreements. About 25 companies are associated with FEMP. Further expansion with other clusters of universities is being investigated.So far some 160 students have taken the programs and are working in all parts of the world in a variety of jobs.The European Commission has recently announced the new “Erasmus World” program that will stimulate the offering of joint programs by European universities and offer third-country students and teachers a greater opportunity for mobility and an enhanced European added value. Host European postgraduate courses will be selected for a five-year period. They will receive funding from the Community and a “EU” seal. Around 250 “EU Masters Courses” will be established.The envisaged new Erasmus program and it’s network and operating practices are very similar to those being used by EMC, EMEC and EGEC. Erasmus World therefore offers a great opportunity for further developments with FEMP as the official body.INTRODUCTIONThe current situation in Europe is that globalisation of the supply of mineral resources has caused the larger mining and the manufacturing companies to expand and invest particularly outside Europe. However these industries still have a great significance for the European Union and its members, which means that mineral engineering know-how is still important in the E.U. It was therefore realised in the mid-nineties that is vital to maintain the very high level of knowledge and skill base in mining engineering and mineral technology that currently exists in the E.U., through good and well-balanced education programs."

Jan 1, 2004

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By Raymond Philippe

Background ?Hatch Water has worked with most major mining companies in Chile on water supply and optimization projects ?Many(copper) mining projects are located in Northern Chile, which hosts the driest desert on earth Water supply options in Northern Chile ?River ?Availability/Rights ?Well(Brackish) Water ?Availability/Rights ?Municipal Wastewater ?Water rights ?Volume ?(Desalinated) Seawater ?Infinite source ?Cost depends on distance and altitude ?Recycling/Reutilization ?Water losses All these options present water quality issues

May 1, 2009

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By G. Couture

"The Glencore Raglan mine Concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. The nickel metallurgical plant was originally designed to process 100 tonnes per hour of ore to produce 130 000 tonnes of nickel concentrate per year at 16% Ni. The increased grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate at 19% Ni. In 2014, the Metallurgical group, with support from BBA, implemented an expert control system on the flotation circuit. This project was initiated to cope with the high variability of the concentrator’s feed. Increasing the plant recovery and final concentrate grade were also important project objectives. The implementation of the expert system ensures better control of concentrate inventory while maintaining maximum plant throughput. This paper describes the successful implementation of the new control system, the control technology selection and the flotation circuit optimization. It will also discuss the performances obtained with this new approach and the improved process stability.IntroductionThe Raglan Mine is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to produce 130 000 tonnes of concentrate annually at 16% Ni. The increasing of the grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate between 18 and 20% Ni."

Jan 1, 2015

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By J. F. Jackson, R. W. Mau

"The first commercial installation in the mineral industry of the ""Verti-Press"" pressure filter was made by Falconbridge Limited at the Strathcona Concentrator to filter copper concentrate. The filtercake produced contains 6 - 7% H2O, an improvement from the 12 - 13% H2O produced by an internal drum filter, at rates of up to 20 t/hr. A novel slurry feed system incorporates a hose pump and a pressurized slurry accumulator.INTRODUCTIONIncreased copper production from Falconbridge Limited operational mines in the Sudbury Area has exceeded the current refinery capacity. A copper concentrate has been produced to overcome this constraint and has been shipped to custom smelters either as a slurry or as a 12 - 13% moisture filtercake utilizing an internal drum filter.With the treatment of the new Deep Copper Zone from the Strathcona Mine, copper concentrate production was forecast in excess of the installed dewatering capacity. The filtercake was too wet to transport by truck and the custom smelter refused to handle this product at the truck unloading site. The filtercake had to be trucked to a rail spur and transloaded into gondola cars. This system was expensive, incurred unaccountable losses and the concentrate was assessed a moisture penalty.To reduce the concentrate moisture content to permit direct shipment by truck, two basic systems were available; vacuum filter followed by a thermal dryer or a pressure filter. Past experience with the high capital and operating costs of dryers led Falconbridge to closely examine the pressure filter alternative.COPPER CONCENTRATE PRODUCTIONThere are two separate circuits at the Strathcona Mill; one treating nickel ore and the other treating copper ore.The rougher concentrates produced by both circuits are conditioned with lime and cyanide before the copper-nickel separation in a flotation columns. The concentrate consisting of cha lcopyrite with mi nor cubanite is very clean as shown in Table I. Currently 50% of the copper in the plant feed reports as copper concentrate, in the past, this has been as high as 70%."

Jan 1, 1990

By Iann Bouchard

Introduction à l?abrasion et l?érosion Avec le temps, tout solide va éroder et user les métaux les plus durs; de plus, la Corrosion va aussi laisser une couche mince et faible d?oxydation qui sera rayée du substrat. Solutions et guide de sélection Les polymères de Henkel Loctite® peuvent: ? Réduire l?abrasion par glissement ? Protège contre les agents corrosifs ? Prévenir la cavitation ? Augmenter l?efficacité ? Réduire la turbulence ? Résister aux hautes températures?

Feb 1, 2008

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By Gunnar Nord

Introduction ??Atlas Copco has customers both amongst Miners and Contractors ??We believe that the contractor's approach to tunnelling is worthstudying ??For a tunnel contractor the incentive is speed as ?30 % of the costs are material related ?70 % of the cost are time related ?A tunnel contractor favours utilizing of the face ?A miner favours utilizing of the gear ??Statement; In mining, a long term average advance rate of more than 10 m / day can be achieved with the excavation techniques availabletoday

May 1, 2009

By J. L. Jambor, T. C. Birkett, W. D. Sinclair

Abstract -The rare-earth elements (REE) form a significant part of the group of so-called "high­ technology" metals whose glamour has attracted both the scientific community and the mining industry. Despite this attraction, world production of REE declined abruptly in 1985 and only recently has begun to approach production levels of 1984. The decline in 1985 was primarily due to decreased demand for light REE used as catalysts in the production of lead-bearing gasoline. Incorporated within the current trend toward increased production of REE is an increasing demand for higher value elements such as yttrium and other members of the heavy REE group, and for specific REE rather than mixed products . The former demand has made some Canadian deposits and prospects economically attractive despite a surplus of REE reserves on a world scale. The chief attractions of Canadian deposits such as Strange Lake, Labrador-Quebec, Thor Lake, Northwest Territories, and Kipawa, Quebec, are that they are relatively rich in yttrium and other heavy REE compared to light REE, and that they offer a potential security of supply to counterbalance the rapidly escalating dominance of China in the world market.

Jan 1, 1992

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By Ning Shi

This paper suggests an alternative design approach for an innovative shovel dipper, for use in ground conditions where cutting of virgin ground rather than scooping of blasted material is required. Not only does the new design have an optimized dimension ratio (width:height:depth) and attachment arrangement (angle, position), but also a non-linear pro¯le in 2D and 3D. The approach is based on the simulation of a shovel's duty cycle to verify a pilot dipper model. In order to achieve a realistic simulation that could be used to evaluate a dipper design, the model is e®ectively a descriptor of actual shovel activity under soft ground conditions. The shovel geometry, motion and operation, with an emphasis on digging and dumping kinematics and dynamics are the principal elements of the simulation. The simulation considers a fresh face location, repeating tucking, digging and dumping swing motions within the geometric range of the machine, ending when no more face material remaining within reach without re- positioning. The simulation yields digging force, friction force, trajectory, ¯ll time, ¯ll factor, etc, which may be integrated into two basic considerations: power draw (output) and volume delivered (production), as indicators of dipper performance. The simulation has been used as a tool to modify an existing dipper design, prior to looping further simulation cycles. Ultimately, an optimized or totally-new-concept shape is realized. A prototype dipper as a fractional scale model will be built to verity the performance under actual mining conditions.

May 1, 2004