Search Documents

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By Richard Maurice

RÉSUMÉ La restauration du site minier Poirier, à Joutel s?est déroulée entre 1998 et 2001. Le principal élément des travaux a été la restauration du parc à résidus et des zones d?épanchement qui totalisaient 4,5 millions tonnes de résidus répartis sur une superficie de 74 hectares. Les résidus sont fortement générateurs de drainage minier acide. La première partie de la présentation consiste en un bref rappel du concept de restauration suivi d?une description des principaux éléments de travaux avec l?emphase sur les leçons apprises de l?exécution des travaux. La deuxième partie de la présentation est axée sur les résultats du programme de suivi en cours depuis la fin des travaux en 2001. Les éléments de suivi se rapportent à la baisse du niveau de la nappe phréatique à l?intérieur de la cellule, au tassement des résidus dans la cellule, aux mesures de température et d?oxygène à l?intérieur de la cellule et finalement à l?amélioration dans la qualité de l?eau de surface. ABSTRACT The reclamation of Poirier Mine, in Joutel, was carried out between 1998 and 2001. The main component of the works has been the reclamation of the tailings basin and tailings spill area which contained a total of 4,5 million tonnes of tailings and occupied some 74 hectares of ground surface. The mine tailings are highly acid-generating. The first part of the presentation will deal with a brief review of the reclamation plan followed by a short description of the main work components laying emphasis on experience gained during construction. The second part of the presentation will deal with the results obtained from the environmental monitoring program still in progress since the end of reclamation work in 2001. The aspects discussed include the drawdown of pore water inside the covered tailing pile, the settlement of mine waste material, the monitoring of moisture, temperature and oxygen underneath the liner and finally, the reduction of loadings in surface water.

Nov 1, 2002

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By Zbigniew J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the US National Science Foundation (NSF) in cooperation with the US Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Geotechnical mapping was performed in 2010 in large excavations of the Davis Campus at the 4850 Level of the former Homestake Mine. LIDAR mapping included laser scanning using a red light laser scanner and 288 Mpixels 360° still camera. The resulting vector map with the photographs digitally draped over the model, was used to create an accurate, virtual model of the excavations. For model verification, the laser scanning was accompanied by surveying and manual mapping of the geology and rock structure. The immediate use of the model was to perform structural analysis and interpretation of geology needed for the design of the DUSEL?s super large excavations. The second round of scanning, after the application of shotcrete to the excavations walls, will be used as a technical blueprint to assess the effectiveness of shotcrete application.

May 1, 2011

By Thomas Deschamps

The main objective of this work was to investigate the effect of binder addition on the geochemical properties of surface paste tailings. Nine leaching columns were prepared following different disposal configurations: non-cemented, non-cemented with cemented layers, and cemented .The proportions of cement by total paste weight were between 0 and 1% for a whole column; the maximum amount of cement in a single layer was 2%. The material used was a sulphide-rich tailings coming from a Canadian hard rock polymetallic mine. The columns have been flushed once a week during 30 weeks. The recovered leachates were analyzed for pH, Eh, conductivity, and a wide range of elements. The drainage rates were monitored during the initial disposal as well as after each column flush. The results show that binder addition can improve the whole environmental performances for some of the studied disposal configurations. The disposal configuration consisting of intercalation of three 2% cement paste layers within non-cemented layers (0.66 wt.% of cement for the whole column), and the configuration with 2% cement added only in the two bottom layers (0,44 wt.% of cement for the whole column), showed the best results in terms of water quality and drainage rates.

May 1, 2007

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By Markus Timusk

This paper describes a research project that focuses on developing a diagnostic routine to assist in decision support for the condition based maintenance of mobile mining equipment subject to unsteady duty. The objective is to develop a general method for initial identification of mechanical faults in machinery operating under non-steady state conditions. The platform to be used for the experimental development and validation of the system is the swing machinery in an electric mining shovel operating in an open pit mining environment. The strategic approach that is proposed for the diagnostic routine will involve using novelty detection augmented by temporal classification.

May 1, 2004

By Glenn S. Dobby, Glenn A. Kosick

"Column flotation circuit engineering has matured to a good level of understanding regarding testing, scale-up and design. Some of the factors important to the process of implementing columns are addressed in this paper, highlighting the following issues• operating bias and the maximum achievable solids carrying rate for a column application.• internal circulating loads of full scale and pilot plant flotation columns• short-circuiting oflarge scale columns and the impact on separation selectivity• the number of stages in a column circuit and the impact on selectivity.The paper uses several case studies, from pilot plant to full scale implementation, to illustrate these design issues.1. IntroductionTen years ago, in 1984, there were very few column flotation installations world wide and the largest columns were about I . 5 to 2 m diameter or square. During the following decade there have been in the heighbourhood of 80 column installations that have been successful and profitable, as both retrofits and green-fields plants. Now, columns as large as 3 to 4 m are not uncommon. Examples of installations with many large columns include Escondida, with ten columns each at 4 m square, and P T Freeport Indonesia, with 21 columns: nine 3 m diameter columns, four 2.4 m diameter columns and, starting up in April I 995, eight 3.6 m diameter columns.During this growth period there have also been column installations that can be considered as failures. In the majority of these cases, the reason for their failure has been an insufficient installed capacity for applications where there is a high weight recovery of solids to the froth product These include zinc cleaning, copper cleaning and iron ore flotation (silica flotation from a feed that is 15 to 30 %Si02) An application with high weight recovery to the froth product makes column scale-up and circuit design more complicated. This is particularly so if a high degree of selectivity is also required while attaining a high weight recovery, which can happen with iron ore flotation in columns."

Jan 1, 1995

By G. Chi, A. Solomon, J. Lai

"The Buffalo gold deposit is a small deposit consisting of auriferous quartz-tourmaline veins within a granodiorite stock in the Red Lake greenstone belt. This study aims to characterize the mineralizing fluids through fluid inclusion and stable isotope analyses and to compare them with those of the world-class Campbell- Red Lake deposit. Four types of fluid inclusions were recognized, including carbonic, aqueous-carbonic, aqueous, and halite-bearing aqueous, with the carbonic type being the most abundant. Raman analyses indicate that the carbonic phase mainly consists of CO2, with minor amounts of N2 and CH4, and rarely detectable H2S. The homogenization temperatures of the carbonic inclusions range from -41.7° to 30.9°C. The homogenization temperatures and salinities of the aqueous, halite-bearing aqueous, and aqueous-carbonic inclusions are 130° to 276°C and 9.7 to 23.6 wt.% NaCl equiv., 155° to 207°C and 32.9 to 42.3 wt.% NaCl equiv., and 215° to 357°C and 8.3 to 19.7 wt.% NaCl equiv., respectively. The d18OVSMOW values of tourmaline range from 8.2‰ to 9.0‰, and those of quartz from 11.4‰ to 11.9‰, with estimated fluid temperatures from 323° to 399°C based on the quartz-tourmaline isotopic geothermometer. It is postulated that separate CO2-dominated and aqueous fluids intermittently invaded the fracture/vein system in response to fluid pressure fluctuations, with limited mixing. The CO2-dominated fluid, previously recognized in Campbell-Red Lake as the main mineralizing fluid, is inferred to have been derived from deeper parts of the crust. This deep CO2-dominated fluid reservoir might have been a common source for gold mineralization in the Red Lake greenstone belt. Le gîte aurifère Buffalo est un petit dépôt composée de veines de quartz-tourmaline à l’intérieur d’un stock de granodiorite dans la ceinture de roches vertes de Red Lake. Cette étude vise à caractériser les fluides impliqués dans la minéralisation par les inclusions fluides et par les isotopes stables ainsi que de les comparer avec ceux du gîte de classe mondiale de Campbell-Red Lake. Quatre types d’inclusions ont été notes, incluant des inclusions carboniques, aqueuses-carboniques, aqueuses et aqueuses avec halite, les inclusions carboniques étant la variété la plus abondante. Les analyses par spectroscopie Raman indiquent que la phase carbonique consiste principalement en CO2, avec des quantités mineures de N2 et de CH4, et rarement avec des quantités mesurables de H2S. Les températures d’homogénéisation des inclusions carboniques vont de -41.7° to 30.9°C. Les températures d’homogénéisation et les salinités des inclusions aqueuses, aqueuses avec halite et aqueuses-carboniques sont varient de 130° à 276°C et de 9.7 à 23.6 poids.% NaCl équiv., 155° à 207°C et 32.9 à 42.3 poids.% NaCl équiv., et de 215° à 357°C et 8.3 à 19.7 poids.% NaCl équiv., respectivement. Les valeurs de d18OVSMOW pour la tourmaline vont de 8.2 à 9.0‰, et celles du quartz de 11.4 à 11.9‰, avec une température estimée du fluide entre 323° et 399°C sur la base du géothermomètre isotopique quartz-tourmaline. Il est postulé qu’un fluide riche en CO2 et un fluide aqueux distinct ont envahi le système de fractures/veines par intermittence en réponse à des variations dans la pression des fluides, et qu’il y a eu peu de mélange. Le fluide riche en CO2 est également observé à Campbell-Red Lake ou il est le fluide minéralisant principal, il est présumé être dérivé de portions plus profondes de la croûte. Ce réservoir profond de fluides riches en CO2 pourrait être la source commune des minéralisations aurifères de la ceinture de roches vertes de Red Lake."

Jan 1, 2009

By A. O. Dufresne

The mineral wealth of pre-Cambrian rocks in Canada has been the subject of much study by geologists and engineers (members of this Institute), particularly so in the past few years, following discoveries of mineral deposits in areas far a part. This interest is well worth sustaining knowing the numerous rich producing mines within the pre-Cambrian formations, and the vast area covered by its rocks throughout this country. The pre-Cambrian has yielded minerals, both metallic and non-metallic; of these a much diversified list could be made. In more than one district we can point to mining as being responsible for the opening up of new sections, attracting a population into regions which otherwise would have remained virgin land of little commercial value. In these pre-Cambrian formations are found the rich copper deposits of Michigan, producing without interruption since 1845, and from which seven billion pounds of copper has been won; while in Minnesota and the adjoining district, at the head of Lake Superior, are mined iron ores which have rendered possible the great steel manufacturing industry of United States, the base of the economic structure of that wealthy country. The pre-Cambrian has given Canada the nickel-copper mines of the Sudbury district, the silver deposits of Cobalt and the gold camps of Porcupine and Kirkland Lake. With all of these our members are familiar; and it suffices to mention them to bring to mind pictures of the wealth and 'the growing population, in a word the importance of mining in?those sections of the country.

Jan 1, 1926

By R. Ramírez, N. Aslin, G. Ríos, T. Bravo, A. R. Almansa

Lacy copper has been an on-going concern at Atlantic Copper for at least 10 years and was first reported to Glencore Technology in mid-2010. Over the past 12 years, many of the plates were replaced due to age and general deterioration however; plate passivation and lacy copper issues have persisted. After analyzing all the possible causes of this phenomena, it was found that the problem is caused by a degradation of stainless steel as a consequence of the deposition of Sb oxides. These deposits act as passivating agents of stainless steel, which reduces the density of copper nuclei, causing defective copper deposit, with low thickness and ductility. After doing several tests for reducing/removing the phenomena, the over-riding factor was found to be the anode-cathode overlap. An adequate overlap eliminates the problem of "lacy copper". This was verified during an eight month trial with anodes extended 2.5cm in length. Longer anode not only avoids the appearance of lacy copper, but also recovers cathodes that already have lacy copper. On the other hand polishing of plates only gives rise to a temporary solution that requires on-going polishing, to avoid the re-appearance of lacy copper. INTRODUCTION The electrolytic copper refinery of Atlantic Copper in Huelva (Spain) was commissioned in 1970 with an initial capacity of 40,000 t of cathodes per year. In 1975 the copper refinery was expanded to 108,000 t/year. From 1994 to 1996, a new expansion together with the implementation of ISA permanent cathode technology led to a capacity of 215,000 t/y. Since 1995, a progressive increase in the current density up to 350 A/m2 has been accomplished, which together with an increase in the number of cells from 1,120 to 1,204, has led to the present cathode production capacity of 290,000 t/y A lack of copper deposition in the lower part of the steel permanent cathodes was first reported in 2010. This phenomenon is known as “Lacy copper” because of the appearance of the copper deposit as it can be seen in Figure 1. The occurrence of this phenomena was relatively low and was assumed to be originated by an excessive anode scrapping. Nevertheless, in December 2015 Lacy Copper was observed in a significant amount of copper cathodes giving rise to the following issues: Increased tramp copper – housekeeping and maintenance problems Poor appearance of cathode deposit and untidy looking bundles

Jan 1, 2019

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019