Search Documents

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By Linruo Zhao, Qi Yang, Akihiro Sato

TiN coating has a wide range of tribological applications from wear reduction of cutting tools to erosion protection of gas turbine engine compressor components. The performance of TiN coating depends on its microstructure, mechanical properties and adhesion strength which are influenced by the coating deposition process. In this study the effects of cathodic arc deposition conditions on the microstructure, hardness, adhesion and erosion resistance of TiN coating were investigated experimentally. It was found that varying deposition temperature, substrate bias and N2 pressure could derive a processing window in which TiN coating with superior erosion performance can be fabricated.

Jan 1, 2010

CI, Data and Data Systems Road Analysis Control Quick and simple manual Analysis Case study Visual relation of analysis

May 1, 2013

By X. Z. Yuan

Contamination introduced by the impurities from the feed stream can impact the PEM fuel cell performance dramatically. The presence of these unwanted trace species such as CO, H2S, NH3, can adversely affect the fuel cell functioning. It has been reported that the major impact of CO and H2S contamination on the fuel cell performance is kinetic while the effect of NH3 contamination is speculated as membrane conductivity reduction only. In this paper, a model regarding the NH3 contamination is described and the mechanism of the NH3 contamination is illuminated by the model calculations.

Jan 1, 2005

By W. Melnyk, L Pokhilenko, J. A. McDonald, A. Hall

The Camsell Lake property comprises 270 000 acres located about 240 kilometres northeast of Yellowknife in the Northwest Territories. Kimberlite has been located in two areas of the property:

Jan 1, 2001

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011

By Geoff Goodyear

UHNL Corporate Profile ? Providing Helicopter Services since 1963 ? A Newfoundland Company head-quartered in Goose Bay, Labrador ? Operations, while primarily Atlantic Canadian, extend across Canada, the Arctic, Greenland ? 16 aircraft, all single engine / VFR Typical Industry Mission Profiles & Work Environments ? Types of missions include: ? Air Taxi & Executive Transport ? Mineral Exploration ? Forest Fire Suppression ? Medivac ? Wildlife Management & Research ? High Angle Rescue and Ice Blasting ? External Load & Long Line ? Mountainous Terrain Operations ? Aerial Application ? Power line Patrols & Construction The Helicopter ? Essentially the same aerodynamic principals as fixed wing but with some mechanical variations on the theme

May 1, 2001

By C. G. Kemsley

THE ore as hoisted is very wet, and difficulty was experienced i~ screening it to remove the fines before going to the secondary crusher. In fact, the fines had a tendency to form balls and roll down the screen, and only a small percentage was removed. Their inclusion with the other ore going to the Symons secondary crusher caused excessive spring action and pounding between the adjustment ring and main frame, resulting in abnormal wear between the two. To overcome this, it was decided to wash the fines through the primary screen, and use an Akins classifier to de-water the screenings, pumping the overflow from the classifier up to the mill and discharging the oversize onto the mill-feed belt.

Jan 1, 1945

By Z. D. Hora

has been no commercial production of either perlite or pumice in British Columbia. Several promising occurrences are known to exist but their development has been delayed due to difficult access and / or remote locations. The Empire Valley perlite deposit is located 120 km east of Clinton. The deposit appears to be a flat-lying volcanic flow 50 to 70 m thick that is part of an Eocene rhyolite and dacite volcanic assemblage. The Francois Lake perlite deposit occurs on the north shore of Francois Lake where perlite is part of a rhyolitic volcanic sequence. The exposure of perlite is about 13 m thick and is considered to be Eocene or Oligocene in age. The Uncha Lake perlite deposit is located about 5 km south Industrial Minerals in Canada of Uncha Lake. Perlite appears to be intercalated with porphyritic rhyolite flows that are comparable to those at Francois Lake. Showings are widespread but poorly exposed and thicknesses are unknown. The Mount Meager pumice deposit is located in the Lillooet River valley at the base of Plinth Mountain. Coarse pumice agglomerate forms a large talus slope that is undercut by the river. Unsorted, angular fragments up to 50 cm in diameter are intermixed with up to 30 per cent of sand and silt-sized particles. The exposed zone is about 200 m long and 50 m high; it is being considered as a source of lightweight aggregate.

Jan 1, 1984

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By Z. D. Hora

Sedimentary phosphate-bearing rocks are found over a considerable area of so utheastern British Columbia that extends from Fernie east to the Alberta-British Columbia boundary and from the International Boundary northward to the headwatei: s of the Elk River. Phosphatic beds occur at the following four stratigraphic levels: 1. lower part of the Banff-Exshaw sequence of Mississippian age; 2. lshbel Formation of Permian age; 3. base of the Fernie Group of Jurassic age; 4. belemnite bed within the Rock Creek Member of the lower part of the Fernie Group. To date, considerable tonnages of phosphate rock have been proven in the area. However, no commercial production has been initiated because of a relatively low P2O5 grade. Data on assays and thicknesses of the phosphatic beds are in part recalculated from the paper by Telfer (I 933) and in part from assessment reports filed at the British Columbia Ministry of Energy, Mines and Petroleum Resources.

Jan 1, 1984

By Wencheng Gao

An attractive way to beneficiate magnesium chloride and aluminum chloride is to prepare Mg-Al spinel, an excellent refractory material. Mg4Al2(OH)14?3H2O, the precursor of spinel, can be prepared using a co-precipitate method from aqueous MgCl2-AlCl3 solutions. The co-precipitation process of magnesium-aluminum from acidified chloride solutions by using NaOH or NH4OH as base neutralization agent was studied. Co-precipitation was conducted from different mixed solutions ? at initial CAl=0.0625M and Mg/Al molar ratio from 0.5 to 10, the temperature range from 30 to 90 °C. The effect of other parameters, including base type, method of base addition, base addition rate, aging time, background electrolyte and concentration were also investigated. The co-precipitation process was monitored by potentionmetric(pH) measurements. The experimental pH curves were characterized by two platforms separated by a steep jump in pH at Mg/Al molar ratio 0.5~6. The first platform was centered at about a pH of 3.8 and the pH of second platform was varied with different conditions. When the Mg/Al molar ratio was up to 6~10, the first platform in pH was almost disappeared. Furthermore, the shapes of pH curves were also affected by base type, base addition rate and method of base addition. Experimental results showed that the first platform in pH was connected with Al precipitation, and the second platform was involved with Mg. The final co-precipitates were characterized by XRD, TGA-DTA, particle size analysis, SEM and TEM. We found both Mg/Al molar ratio and temperature proved to be the key parameters controlling the formation of Mg4Al2(OH)14?3H2O phase. At solution Mg/Al ratio=0.5~4, the main precipitate phase was Bayerite (Al(OH)3) admixed with Mg4Al2(OH)14?3H2O; at Mg/Al ratio=4~6, the main phase was Mg4Al2(OH)14?3H2O admixed with some Mg(OH)2; while from Mg/Al ratio=6~10, the systems were mixtures of Mg(OH)2 and Mg4Al2(OH)14?3H2O.

Oct 1, 2011

By Arthur Lieu

Outline Removal mechanisms of Se and Mo in the Key Lake Bulk Neutralization circuit Bulk circuit Detail process modification in the Key Lake BN circuit Process performance after commissioning Objective Legacy effects of Se and Mo from the historical operation of Key Lake mill were shown to have an negative effect on the regional biota in the downstream environment. The water treatment circuit was not designed to remove Se and Mo from the effluent. Reduce Se and Mo concentrations in final effluent under0.028 0.028 ppm ppm and 0.3 and ppm ppm(CNSC regulatory limits).(limits).??????

Nov 1, 2011

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By Jian Deng, Haitian Sun, Zengqian Hou, Shuhe Song

"Abstract - Volcanogenic massive sulfide (VMS) deposits, an important base-metal deposit type in China, occur widely in submarine volcanic districts of variable magmatic affinities. These VMS deposits range in age from Archean to Mesozoic, but most are in Proterozoic and Paleozoic sequences. More than 60% of VMS deposits formed in the Paleozoic, the most important metallogenic eon. Three important Paleozoic VMS-metallogenic provinces include Northern Qilian, Sanjiang and Altai provinces. The Proterozoic constitutes the next important era, but with no VMS deposits in the middle Proterozoic. VMS deposits associated with the Proterozoic volcanic rocks occur around the Yangtze Platform and in the western Kunlun-Qinling. The Triassic is third in importance, with VMS deposits concentrated in the Sanjiang Tethys. The Archean has only one VMS deposit, on the northern margin of the Sino-Korea Platform.Five distinct compositional classes of Chinese VMS deposits have been distinguished: Cu, Cu- Zn (or Zn-Cu), Cu-Fe, Zn-Pb-Cu, and Pb-Zn (-Cu). The Cu, Cu-Co, and Cu-Zn types of deposits occur sporadically from the Archean to Paleozoic, and are closely associated with mafic and ultramafic volcanic sequences. The Zn-Pb-Cu and some Cu-Zn type deposits are restricted to the Paleozoic and Triassic, and are hosted by calc-alkaline felsic rocks in bimodal basalt-rhyolite sequences, whereas Cu-Fe and Pb-Zn type (except for the Laochang deposit) deposits are restricted to the Proterozoic and occur in calc-alkaline volcanic sequences. As large quantities of marine mafic volcanic rocks were deposited in western China, Cu and Cu-Zn deposits are major types of Chinese VMS deposits.Chinese VMS deposits formed in a wide range of paleo-tectonic settings and depositional environments, such as island-arcs, rifts, aulacogens, and ocean ridge hot spots. Among these, the rift and back-arc environments are the most important, containing about 60% of Chinese VMS deposits. Aulacogens are a subordinate environment where most of the Proterozoic VMS deposits formed. The oceanic ridge and hot-spot systems are common in the tectono-magmatic domains in China, but contain only a few small Cu and Cu-Zn type VMS deposits.The Chinese VMS deposits have usually been influenced by both deformation and metamorphism to various degrees, resulting in changes in the shape and metal distribution. Seven representative deposit styles have been recognized: sheets, sheet plus strata-bound stringer, cyclically zoned deposits, mounds, mound-like deposits, strata-bound stringer-disseminated, and stockwork-disseminated deposits. The formation of these various styles of deposits is controlled by several key factors, such as lithology and permeability of the host rocks, focused or unfocused discharge, temperature and chemical composition (e.g., salinity) of hydrothermal fluids, as well as depth of seawater."

Jan 1, 1999

By J. H. Hodgson

"Those of us who have been concerned with the problem of geophysical exploration in southwestern Ontario have followed the development of the Poulter method with much interest. I have much appreciated the opportunity of reading an advance copy of Dr. Poulter's clear exposition and of preparing the following brief remarks on the probable applicability of the method to the Palaeozoic area of southwestern Ontario.During the years 1944 to 1946, the Ontario Department of Mines, in co-operation with the Union Gas Company and the Dominion Natural Gas Company, operated an experimental party in the hope of establishing a seismic technique appropriate to the •area. The results were completely negative. During two summers' field work, no reflections whatever were obtained except in one area near Windsor. It is the •purpose of these remarks to inquire whether Dr. Poulter's techniques might yield favourable results.It was the conclusion of the report on our work that two principal causes contributed to the failure of the method. In the first place, the geological column possesses few elastic discontinuities and those that exist appear to have low reflection coefficients. In the second place, the area is drift-covered in general. This drift complicates the situation by absorbing seismic energy and by giving rise to groups of complicating refracted phases which obscure the entire interesting section of the record. The situation is further complicated by the high reflection velocities and the relative shortness of the Palaeozoic section, these factors combining to bring in a reflection from the basement in about half a second."

Jan 1, 1950

By M. J. Michaud, M. J. Lavigne

"Abstract - North American Palladium Ltd. operates its Lac des Iles open pit palladium mine 85 km north of the city of Thunder Bay, Ontario. The Roby Zone deposit occurs within the mafic/ultramafic Lac des Iles Intrusive Complex (LDI-IC), which was created by multiple pulses of magma of varying composition within several closely spaced chambers. Chaotic lithological distribution, the presence of magmatic breccias, and the rarity of rhythmic layering suggest a dynamic intrusive environment with disruptive magma pulses. As of December 31, 2001, measured and indicated resources for the 950 m long by 815 m wide Roby Zone deposit totalled 159 Mt grading 1.55 g/t Pd, 0.17 g/t Pt, 0.12 g/t Au, 0.05% Cu, and 0.05% Ni at a palladium cut-off grade of 0.7 g/t. The Roby Zone contains an additional 73 Mt of inferred resources at similar grades.The Roby Zone is dominated by varitextured gabbro containing pipes and pods of breccia, and large blocks (~60 m across) of varying lithology. Mineralization at Lac des Iles occurs as: (1) a PGEand base metal-rich magmatic matrix of breccia (breccia ore); (2) mineralized dikes or sills (gabbronorite in North Roby ore); (3) lower-grade mineralization in varitextured units that are host to the distinctive breccia ore and envelope the North Roby ore; and (4) high-grade mineralization associated with strong silicate alteration exemplified by high-grade ore.The close spatial association of the mineralized breccias with both varitextured units and silicate alteration leads to an interpretation that the energetic magma that created breccia was charged with a dissolved fluid, and that this deuteric fluid exsolved at high temperatures to migrate through crystal mush, enhancing crystallization along its pathways, resulting in variable grain size. This transformation occurred at high temperature and produced sulfide-poor, varitextured gabbro-hosted mineralization exemplified by some of the mineralization in the North Roby Zone, and also found throughout the Roby Zone. The association of hydrous silicate alteration with mineralization can be explained by continuing fluid migration during cooling and continued metal transport. Résumé - North American Palladium Ltd. opère la mine à ciel ouvert de Lac des Iles située à 85 km au nord de Thunder Bay, Ontario. Le gisement Roby Zone est encaissé dans le complexe mafique/ultramafique de Lac des Iles (LDI-IC), lequel représente une intrusion polyphasée créée par plusieurs pulses magmatiques de différente composition à l’intérieur de chambres magmatiques fermés. La distribution chaotique des lithologies, la présence de brèches magmatiques, et la quasi-absence de litage rythmique suggèrent un environnement magmatique dynamique perturbé par l’introduction de nouveau magma. Au 31 décembre 2001, les ressources mesurées et indiquées s’élevaient à 159 millions de tonnes titrant 1,55 g/t Pd, 0,17 g/t Pt, 0,12 g/t Au, 0,05% Cu, et 0,05% Ni, pour une teneur de coupure de 0,7 g/t Pd. De plus, la Roby Zone contient 73 millions de tonnes de ressources inférées à une teneur similaire.La Roby Zone est principalement encaissée dans un gabbro de texture hétérogène (varitextured) caractérisé par des cheminées et des lentilles de brèches et des énormes blocs (environ 60 m de diamètre) de plusieurs lithologies. Au Lac des Iles, la minéralisation en EGP et en métaux de base se retrouve dans la matrice magmatique de brèches (breccia ore), dans des dykes ou des sills minéralisés (gabbronorite dans la zone North Roby ore), comme minerai de basse teneur encaissant le minerai de brèche (breccia ore) et enveloppant la zone North Roby. Du minerai de haute teneur est également associé avec une forte altération en silicates dans la zone high-grade ore.L’étroite association spatiale entre les brèches minéralisées et les unités de texture variée (varitextured) et l’altération en silicate suggère que le magma énergique qui a causé la bréchification était chargé de fluides. Ces fluides deutérique"

Jan 1, 2001

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954

By R. H. Seraphim

"The Phoenix Camp, in the Boundary Creek district of southern British Columbia, produced before 1920 about 15 million tons of ore averaging more than l ·5 per cent copper, about 0.03 ounces per ton in gold, and 0·5 ounces per ton in silver. Attwood Copper Mines Ltd. conducted an exploration program in the Phoenix area from 1951to1953.Publications on the camp are listed in the bibliography. Brock's work was not sufficiently detailed to unravel the structural and stratigraphic pro bl.ems. The work of LeRoy and McNaughton is referred to later.The stratigraphic column is as follows:Tertiary.Midway Formation: Volcanics and hypabyssals; dacitic to basaltic flows, with associated dykes and sills of syenite (pulaskite in part) and augite porphyry.Jura-Cretaceous.Intrusives of quartz diorite and diorite (nearest outcrop two miles from Phoenix).Late Palaeozoic or Triassic (Attwood Series).Brooklyn Formation: Sharps tone conglomerate, limestone, grey-wacke and/ or andesitic tuff, with minor shale and basalt. Rawhide Formation: shale with minor conglomerate.Early Palaeozoic.Knob Hill Formation: Chert and andesite, with minor limestone, shale, and serpentine.This column differs from that of LeRoy in two important respects: (I) Attwood's work indicates that the Rawhide shale is basal to, rather than stratigraphically above, the Brooklyn formation. The shale contains conglomerate lenses, which become more abundant and thicker toward the top, and grades upward into Brooklyn conglomerate. Ripple marks indicate that the shale is right side up."

Jan 1, 1949

By W. Yang, R. Rajasingam, K. Mohanarangam

"Copper Electrowinning (EW) is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. The process setups up a complex flow pattern within the cell as it is subjected to varying density gradients due to the deposition process along with oxygen bubble driven flow. It is a necessity to understand and quantify the flow behaviour within these cells in order to maintain the production of highest grade copper. In fact, the oxygen bubbles originating from the process is responsible for the generation of acid mist which is a designated as a carcinogen a major health hazard around EW tank houses. Hydrodynamic assessment of the process has so far been restricted to simple mass balances and some limited numerical modelling. All the models are based on assumed boundary conditions which has not so far been verified by any real-time physical measurement. This apparent gap has led to models which could not be directly used to track process changes or troubleshoot problems in EW tank houses. In order to address this gap, CSIRO has established a full size (width and height) transparent cell capable of simulating plant operating conditions (across the range currently used). With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables (current density, flow rate, temperature, etc.) independently and their effect of bubble size, bubble velocity, gas hold-up as well as acid mist generation and its size. In order to address safety concerns in tank houses around acid mist early results outlining the factors contributing to its generation as well as the effect of various barriers to mitigate acid mist is outlined below.INTRODUCTIONA significant part of today’s copper production is through hydrometallurgical route which predominantly involves leaching, Solvent eXtraction (SX) followed by ElectroWinning (EW). Producing copper using this approach have shown to be environmentally friendly (Dresher, 2001) compared to the traditional smelting process. EW is the final step in the production of LME grade copper using the hydrometallurgy route. The electro-chemical process involves the use of a lead anode (Pb-Sn-Ca) and a stainless steel cathode to produce copper sheets using the copper rich electrolyte from the SX process and with the applications of direct current to the electrodes. This electro-chemical reaction results in the deposition of copper ions on the cathode with oxygen released from the anode as a by-product. Hydrodynamically, the oxygen bubbles create a bubble driven flow within the EW tanks with the surrounding electrolyte. A direct result of this could be seen from the quality of the copper deposited on the cathode. Most of the copper plates produced from the traditional tank houses have a rough texture at its bottom one-third while the top two-thirds have a smooth finish with a finer grain structure."

Jan 1, 2016