Search Documents

By L. A. Gomieroa

The Caetité-Brazil uranium facilities produce about 340 t/y of uranium from an ore averaging 0,25 U %. The process steps are ore crushing, heap leaching with sulfuric acid, U separation and purification by solvent extraction with tertiary amine followed by stripping with sodium chloride solution and precipitation as ammonium diuranate that is dryed. A change in the milling process is being evaluated to increase the production and the uranium recovery. Heap leaching will be changed to conventional tank agitated leaching of the ?590 ground ore slurry in sulfuric acid medium. The replacement of the stripping reagent is also being considered.

Aug 1, 2010

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By Finley A. Campbell

"Nickel-copper sulphide deposits associated with basic rocks in the Quill Greek area and the White River area in the Yukon Territory have been studied and compared from the view-point of their general geology, structural geology, and the mineralogy of the ores. The relative amounts of the major constituents, magnesium, iron and calcium, and the minor constituents, nickel, cobalt and chromium have been determined spectrographically for two cross sections of the basic rocks at Quill Creek and one at White River. These data, along with petrologic and field evidence, were used to determine the sill and dyke-like character and nature of the basic intrusions. Loss on ignition is employed as a measure of the degree of serpentinization. The distribution determined shows that the serpentinization does not appear to have greatly influenced the inferred original distribution and lithophile associations of magnesium and nickel. The cobalt content may have been altered.The nickel content of the serpentinized peridotites ranges from an average of 0.36 per cent in one section to an average of 0.24 per cent in each of the other two sections studied. The cobalt averages 0.0038 per cent in the samples from the two Quill Creek sections and averages 0.0042 per cent at White River. These results have been compared with other available data.The sulphide ores are later than both the peridotite and gabbroic rocks and may be co-magmatic with them. There is no evidence in these areas to support an origin by lateral secretion; on the contrary, the alteration associated with the ores, the mineralogy and spatial relationship to basic and ultrabasic rocks, indicate the ores are derived from a basic magma."

Jan 1, 1960

By C. A. Pickles, K. Mackowiak, D. Gajonera

"Shake-flask oxidation tests were performed on Red Dog mine waste to study the initial dissolution behaviours of lead, zinc, and iron. The conditions for accelerated acid generation in terms of Eh and pH were determined. Each mineral behaved distinctly, with galena dissolving first, followed by sphalerite, then pyrite, although there was some overlap in behaviour. Iron was not detected in solution until approximately day 40 and was present at low concentrations. The experimental conditions and the theoretical model results indicated the formation of iron oxyhydroxides at low weathering times and jarosite at longer times.RÉSUMÉ Des tests d’oxydation par agitation en flacon ont été effectués sur les déchets miniers de l’exploitation Red Dog afin d’étudier les comportements initiaux de dissolution du plomb, du zinc et du fer. Les conditions entraînant la production accélérée d’acide en termes d’eH (potentiel d’oxydoréduction) et de pH (potentiel d’hydrogène) ont été déterminées. Chaque minerai se comportait différemment ; la galène a été la première à se dissoudre, suivie de la sphalérite, puis de la pyrite, mais un certain chevauchement des comportements a été observé. La présence de fer en solution n’a été détectée qu’après environ 40 jours et ce, à de faibles concentrations. Les conditions expérimentales et les résultats du modèle théorique signalaient la formation d’oxyde-hydroxyde de fer sur de courtes périodes d’altération atmosphérique, et de jarosite sur des périodes plus longues."

Jan 1, 2017

By David C. Cook

The milling complex, situated just east of the Cassiar townsite, receives raw ore from the tramline and processes it into 105,000 tons per year of milled asbestos fibre. The ore is passed through a concentrator, where a barren rock fraction is removed. The concentrated ore, representing 70% of the feed, is dried, stored and then milled into nine separate fibre classifications. The finished product is packaged into 100-lb bags and loaded into trucks in one-ton units. New air-handling facilities were added in 1977to provide additional air for environmental control.

Jan 1, 1978

By Sebastian Siebert

Unmanned Aerial Vehicles (UAV) as a data acquisition platform and as a measurement instrument have become attractive for many surveying applications in civil engineering. However, their performance is not well understood for these particular applications. The specific scope of the presented work is the performance evaluation of a UAV system that was built to rapidly acquire mobile 3D mapping data for large earthmoving construction sites. Details to the components of the developed system (hardware and control software) are explained. A novel program for photogrammetric flight planning and its execution for the generation of 3D point clouds from digital mobile images is explained. A performance model for estimating the position error was developed and tested in several realistic construction environments. Results to these tests are presented as they relate in particular to large excavation and earth moving construction sites. Results and experiences with the developed UAV system are in particular useful for researchers or practitioners in need for successfully adapting UAV technology for their application(s).

Aug 1, 2013

By P. K. Kaiser, F. Amann

"Rock mass characterization for deep underground construction and mining offers many challenges. This paper first describes some of the key challenges when characterizing highly stressed brittle rocks and then offers some guidance on how to arrive at reliable rock mass strength parameters for deep mining applications. Focus is placed on characterization for rock mass strength determination. It is illustrated how the common use of currently available rock mass characterization systems tend to underestimate the strength of rock at depth. Modifications to currently adopted approaches, i.e., the use of Geological Strength Index GSI for rock mass strength determination, are presented.INTRODUCTIONFor green fields projects, the first challenge of rock mass characterization stems from a lack of access to examine the rock mass at scales larger than typical core sizes (i.e., ~63mm in diameter) until late in the mine design when the flexibility for making changes is constrained. Hence, rock mass characterization often has to rely on information derived from boreholes alone (e.g., core, logs, etc.). This challenge is lessened when mines are expanded from existing operations. A second challenge is related to changing rock mass behaviour with increasing depth and stress. At depth, the rock is highly stressed, thus closer to failure, and often highly confined which leads to a higher interlocking with elevated strength but more brittleness. The goals of rock mass characterization are to be tailored to the technical goals of an investigation. For example, for cave engineering, the workflow includes the assessment of five key engineering aspects (Brown, 2007): Caveability; fragmentation; cave performance; extraction level stability; and mine construction (rock support). Each engineering aspect has to address specific engineering questions and each design component is influenced by different rock mass behaviour aspects and thus is dominated by different rock mass properties, e.g., the vulnerability to stress fracturing (spalling), the bulking characteristics for flow control and support selection, and the confining stress impact on pillar or support design. An effective rock mass characterization program, including logging, mapping and laboratory testing, thus has to collect and interpret features that are relevant for the above listed purposes. Some of the predominant factors are: block volume of defected and non-defected rock; spalling strength; tensile strength of defects; rock mass modulus; and rock mass strength parameters for application to low and high confinement design aspects."

Jan 1, 2015

By A. J. Rigby

Computer generated, actual-scale furnace models have been imported into a rendering software application to provide for impressively realistic surface features and lighting. When these models are imported into a 3D engine framework, it is possible to create content-rich virtual environments allowing for complete interactivity and could provide for a powerful tool to conceptualize refractory lining designs. This technology has been applied to illustrate the optimized design concept of an anode-refining vessel, which can be expected to be completely relined in six days and to last for 4-5 years with minimal partial relining. This technology could easily be applied to other smelter furnace, converter and refining vessel designs.

Jan 1, 2007

By Robert E. McIvor

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency also has been used extensively by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which is appended hereto. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided.Comminution is responsible for a major portion of mineral processing plant energy consumption and operating costs. Bond Work Index efficiency provides valuable means, first, for benchmarking one’s plant performance against others in the broad industry, and hence defining the extent of the opportunity for improvement. Secondly, improvements in circuit efficiency with implemented changes can be quantified and monitored as part of continuous improvement efforts. These two important business activities are thus facilitated, and, in the absence of any other accepted method, otherwise would be lacking without the existence and application of this standard for comparison. While often loosely applied in the past by plant metallurgical staffs, the increased precision offered by this guideline provides much clearer definition of both the conceptual and statistical meaning of these measurements. Even a small improvement can be enormously financially important, but only if differentiated by measurement. This guideline was thus intended to provide industry improved means to differentiate comminution circuit efficiencies. Carbon footprint reduction is coincidental, but nevertheless can be substantial.The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies."

Jan 1, 2016

By Christoph Mueller

?Globalization and the impact on mine operations? is one of the themes of the 2003 annual CIM meeting. Global mining business in practice always means to act with local base material resources in order to reach the mining company?s global business goals. On the other hand these operations are characterized by cost pressure and cycling product prices. Driven by actual prices, local product markets and local production cost, one time one mine can be most efficient while under different circumstances another mine will be the most efficient producer for the same customer [PENSWICK, 2001]. Therefor in the future the most profitable mining companies will be those who have permanent ?real-time? control on their actual production cost level. Certain approaches are under way to provide reliable modeling tools for aiding mining companies in highly complex decision finding procedures. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory? [WIGDÉN, 2001]. Crucial to all these activities is the ability of getting reliable, just-in-time information from the entire mining production chain. As modern mining machinery today is controlled electronically and even already operated autonomously, the theoretical preconditions for the data acquisition is already fulfilled. But up to now, there was no way of cost effectively exchanging the process information with databases, simulation tools and other enterprise level software. Any data exchange problem had to be solved by individual and expensive software development projects. To solve these problems, the International Rock Excavation Data Exchange Standard (IREDES) was launched in 2000 by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. The standard?s technical architecture is flexible and open - also for future applications. It uses modern technology enabling easy data exchange with commercial databases as well as open on line networking.

May 1, 2003

By P. E. Georghiou, S. Shafiei Zadeh, H. Hassan Nejad

Data are presented on the extractant behaviour on toxic metal removal from spent hydroprocessing catalyst, produced at the North Atlantic Refinery plant in Newfoundland and Labrador. Aliquat 336 was selected due to its potential capabilities for the separation of cobalt, molybdenum and nickel from the leachate extractant produced by aqua regia. The solvent extraction process was statistically modeled using central composite design (CCD), and the numerical optimization was conducted to achieve the optimum point for toxic metal recovery for the extractant.

Jan 1, 2014

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By J. O. Marsden

Over the past eight years, Phelps Dodge (a division of Freeport-McMoRan Copper and Gold, Inc.) has developed a suite of proprietary hydrometallurgical processes for the treatment of copper concentrates as an alternative to conventional smelting and refining technology. The technical viability of two processes has been commercially demonstrated in a large scale plant at Bagdad, Arizona, designed to process approximately 52,500 metric tons per year of concentrate containing 30.5% copper. The first process utilizes high temperature (225°C) pressure leaching, followed by countercurrent solid-liquid separation, and then blending of the copper-bearing solution with low grade stockpile leach solution for subsequent treatment by SXlEW for copper recovery. The second process uses super-fine grinding, medium temperature (l60°C) pressure leaching, followed by solid-liquid separation, and treatment of high grade copper-bearing solution by direct electrowinning to recover the bulk of the copper values. The latter process will be utilized at Morenci in a commercial facility designed to treat mixed chalcopyrite-chalcocite-covellite concentrates. This facility is scheduled to start up in 2007. Other flowsheet options have been developed by Phelps Dodge for application to a variety of concentrate materials in specific situations. Examples of various flow sheet options are presented in this paper, and the advantages and disadvantages associated with each are discussed in detail.

Jan 1, 2007

By Asfahani. Jamal, Randa Mohamad

"Abstract - Electrical and structural characteristics of formations favorable for sulfur occurrences in northeast Syria are described using geo-electrical prospecting methods. Simple (VES) and combined (CVES) Schlumberger vertical electrical soundings and geo-electrical profiling using a Wenner configuration were applied to the Teshreen structure. Six profiles (A, B, C, D, E, and F) at the borders of anticlines, where positive and negative structures are joined and salt formations have a tendency to disappear, were studied.Secondary structures, characterized by high apparent resistivity exceeding 3000 Ohm.m were located on each profile using a Wenner profiling configuration. These secondary structures are demonstrated to be favorable for sulfur prospecting by both drilled wells and vertical electrical soundings. Traditional interpretation of the 84 VES measurments is supported by data from 14 CVES measurments. The CVES technique is a powerful tool, due to its improved resolution of the electrical boundaries.Thicknesses and resistivities of the Lower Al-Fares, Al-Garibeh, and Al-Dibbaneh formations were determined through the interpretation of VES measurments. The same VES measurments were then interpreted using the Pichgin method, whereby all the subsurface tectonic features were determined for depth penetration corresponding to AB/2 = 1000 m. The integration of the first and second VES phases creates a clear picture of the subsurface, including tectonic, geometric, and geoelectrical information. In summary, the sulfur occurrences in the research area are controlled by tectonic paths that are well defined by geo-electrical methods. These diverse geo-electrical methods could be used successfully for sulfur prospecting in similar environments."

Jan 1, 2002

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

By T. Stergiou

An extensive research is being carried out on the shaft furnace operation in order to minimize down-times and reduce operational cost. The need to increase the scrap percentage on the charging mix, together with the need of cheaper spare parts has led to the investigation of alternative materials for the burner system on the shaft furnace. This system consists of a burner block and a flame holder. Traditionally these items are constructed either from SiC ? oxide bonded or SiC-nitride bonded. A lot of problems have been confronted over the past 8 years of operation. Usually, large cracks are formed on both flame holders and burner blocks. This resulted in leakage of combustion gases to the back of the lining and a quick erosion of it. Additionally, the burner blocks suffer from chemical erosion, due to the increased amount of scrap used in the charging mix and the presence of slag inside the furnace. Alternative materials such as stainless steel for the flame holder and alumina-chromia refractory for the burner block have been tested in terms of life-time and resistance on chemical erosion. Furthermore, additional changes have been made on the burner block design in order to alter the flame shape and improve the scrap melting operation.

Jan 1, 2007

By Yoginder P. Chugh

Beginning in 2010, a scientifically-founded water spray system for continuous miners (CMs) has been in development at Southern Illinois University that significantly reduces respirable dust exposure for workers in the face area (patent pending). It includes engineered sprays around the cutting drum, outer bitring sprays, chassis sprays and side cutter boom sprays. About 3.6?4.5 m behind these sprays are additional sprays that cover the area between the CM chassis and the mine roof and ribs. The innovative spray system uses approximately the same volume of water as spray systems currently used on CMs and with similar operating pressures. The innovative spray system design also takes into consideration coal dust wettability. An Illinois mine decided to implement these concepts on a CM during the rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric dust sampling and real-time monitoring with multiple personal dust monitors. The average results based on gravimetric sampling of about 105 cuts show about 30 and 20% reduction in dust exposure for the miner operator and the haulage unit operator, respectively. Visibility in the mining areas was also significantly improved. Since the initial demonstration, the coal company has implemented the system on all of their operating CMs.

Aug 1, 2013