Search Documents

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

By Y. Mitsuda, Y. Kayanuma, T. H. Okabe, M. Miyake

A new process to recover platinum group metals (PGMs) from automotive catalyst scrap using metal vapor was developed. To improve the efficiency of the acid dissolution process of PGMs, metal vapor of reactive elements such as magnesium or calcium were contacted with spent automotive catalyst. It was expected that metal vapor would react with metal selectively and form intermetallic compounds. The specimen of the spent catalyst was treated at 1173 K for 3 h, and it was then dissolved in aqua regia for 1 h to recover PGMs. After the reactive metal treatment, 88% of Pt, 81% of Pd, and 72% of Rh in the catalyst scrap was dissolved, while only 77% of Pt, 69% of Pd, and 38% of Rh was dissolved from untreated scraps.

Jan 1, 2004

By Fidelis T. Suorineni

HydraboltTM is a Swellex-type dowel support element developed and manufactured by New Concept Mining in South Africa. Like Swellex, the HydraboltTM is a folded tube which can be inserted into a larger diameter hole without pushing. It is then activated by injection of high pressure water which inflates the folded tube to intimate contact with the walls of the borehole at a set pressure, normally 25 MPa. Unlike Swellex however, the set water pressure at the end of the inflation is maintained throughout the life of the dowel. An integral non-return valve makes this possible. The HydraboltTM is being investigated as a possible stress change measuring cell. This paper presents the results of closed form solutions, numerical modeling and laboratory test to date. Preliminary results indicate that the HydraboltTM can be used as a stress change monitoring cell in addition to its conventional role as a rock mass reinforcing element. If successful, the HydraboltTM will supplement microseismic monitoring systems in rockburst-prone ground conditions where they will give quantitative stress change data for both mine design model calibrations and means for proactive safety measures.

Oct 1, 2010

By Ken Major, Anita Marks, Craig Sams

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By Richard Dawson

Increasing global demand for coking coal has initiated several new coal mine developments in northeast BC. These developments are able to take advantage of the currently under utilized infrastructure that was put in place during the 1970?s and 1980?s for the Quintette and Bullmoose coal mines; which includes the Town of Tumbler Ridge, a 1,000km rail line to the coal terminal at Prince Rupert and a road system providing highway access to the town site. Coal within the two foothills regions of BC (north-east and south-east) is mined by open pit truck/shovel methods. Optimized mine plans require a thorough understanding of Rocky Mountain structural geology, attention for access in steep terrain, and a related understanding of the geotechnical conditions that control the stability of pit slopes and waste dumps. Thus there is a requirement to properly integrate mine planning with geotechnical engineering considerations. Many of the technical issues are well understood from experience during the past 30 years of Western Canadian coal mining. The challenge is to ensure that the mine plans are able to take full advantage of these lessons learned. The paper will focus on mine planning and geotechnical design issues to do with high angle-of-repose waste dumps and steeply bedded footwall slopes to illustrate the advantage of properly recognizing the important stability control issues during the early stages of engineering evaluations. Case histories from the existing and planned coal mining operations will be presented.

May 1, 2006

By P. Keller, T. E. Lister, G. G. Clark, L. A. Diaz

As electronic technology continues to evolve there is a growing need to develop processes which recover valuable material from antiquated technology. This need follows from the environmental challenges associated with the recovery of raw materials and fast growing generation of electronic waste. Although present in small quantities in electronic devices, the availability of raw materials such as rare earths and precious metals becomes critical for the production of high tech electronic devices and the development of green technologies (i.e. wind turbines, electric motors, and solar panels). Therefore, the proper recycling and processing of electronic waste presents an opportunity to stabilize the market of critical materials, providing a proper disposal and treatment of a hazardous waste stream. This paper describes the development and techno-economic assessment of a comprehensive process for the recovery of value and critical materials from electronic waste. This hydrometallurgical scheme aims to selectively recover several value streams (base metals, precious metals, and rare earths) present in electronic waste. The economic feasibility for the recovery of rare earths from electronic waste is mostly driven by the efficient recovery of precious metals, such as Au and Pd (ca. 80 % of the total recoverable value). Rare earth elements contained in magnets (speakers, vibrators, and hard disk storage) can be recovered as a mixture of rare earth oxides which can later be reduced to the production of new magnets.

Jan 1, 2016

By R. D. Brown

"AbstractOver the past five years, tax rates in the Canadian mining industry have skyrocketed upward across Canada, as both federal and provincial governments have sought to increase their share of mining revenues.However, the past few years have not only brought high tax rates to the industry, but also a number of important new federal and provincial tax incentives.In large part, these incentives ~ special credits or reduction in tax for carrying out specific exploration, processing or other activities - have helped to moderate the adverse effects of the higher tax rates and have provided inducements for exploration and processing activities which might not otherwise have been undertaken.However, the effectiveness of certain of these incentives can be questioned: our over-all tax structure now consists in large part of punitively high marginal rates with some extraordinarily generous but capricious tax reductions for specific activities and may not be in the best long-term interest of either the industry or the nation.A rational tax structure, with moderate and stable tax rates, together with reasonable incentives confined to activities specifically requiring them, could be a more effective spur to investment than the present tax and incentive jungleIntroductionIN THE YEARS since federal tax reform, the mining industry in Canada has faced a continued escalation in its tax burdens as federal and provincial governments have leapfrogged each other in imposing new and higher taxes on the industry. The result has been that marginal tax rates imposed on mining and processing activities throughout Canada have jumped to hitherto unparalleled levels."

Jan 1, 1977

By Jeremy D. Glennon

A number of exciting challenges, opportunities and unanswered questions remain concerning the chemistry, geochemistry, medical, industrial and analytical applications of gold and its compounds.1 Among the challenges presented is the need for extraction methods for gold, at process and indeed analytical scales, that avoid the use of organic solvents or hazardous reagents. Extensive environmental contamination has occurred in the Brazilian Amazon from the mercury-gold amalgamation process. Major problems with the cyanidation process are the relatively slow dissolution kinetics and the health and environmental problems associated with it. With innovation and technical changes, a cleaner way for solubilising and extracting this versatile precious metal can be found. This cleaner future may lie in supercritical fluid science. Interestingly, geochemical studies of gold solubility and speciation in hydrothermal solutions have highlighted the importance of supercritical conditions and sulphur species in the deposition of gold in natural environments. Gold solubility in supercritical brines is far higher than previously supposed while interest in the high content of carbon dioxide in the mineralizing fluids is growing. 2,3 In recent years, also, there has been a tremendous amount of attention paid in analytical chemistry and in industry, to the area of supercritical fluid extraction (SFE) of organic and metallic species. 4 This interest has been fuelled by the introduction of more stringent environmental control and the subsequent need for cleaner solvents and processes to replace established ones. Carbon dioxide is the substance of choice for SFE because of its moderate critical parameters (Tc = 31oC, Pc = 73atm), inertness and availability in pure form. It is an excellent extraction medium for non-polar and moderately polar species, and with careful ligand design, it can be used for analytical and process scale metal extraction from solution and solid phases. In general, the dissolution of a metal in supercritical CO2 (sc-CO2) requires that the charge on the metal ion be neutralised on complexation by the ligand or through a form of ion pairing (analogous to the situation where metal ions are extracted into organic solvents, such as methyl isobutyl ketone or toluene). In this way, then, many chelating agents such as dithiocarbamates and hydroxamic acids have been utilised to extract metal ions such as Cu and Fe into sc- CO2, the process greatly enhanced by the use of fluorinated ligand derivatives. 5-7 In this review paper, we show that supercritical conditions and complexation with sulphur donor atoms, important in the natural deposition of gold, can form the basis of a clean, eco-friendly chemistry for gold extraction. Analytical scale extractions of gold from a variety of matrices can be conveniently used to assess the efficiency of any new proposed ligand.

Oct 1, 2003

By D. Laguitton

"Mathematics, process theory, process practice and computer applications are the main disciplines that contribute to developing useful techniques for computer simulation of mineral and coal processing plants. As in any multidisciplinary effort, communication or transfer mechanisms must be developed to facilitate the flow of experience between participants of different backgrounds. These mechanisms include written reports, verbal communications, workshops and transfer of computer programs. The SPOC project at CANMET is devoted to computer simulation and as such has addressed, or will address in the near future, problems inherent to methodology transfer. The first major output of the project was the material balance program, MATBAL2, which has been acquired by over 30 organizations. Program documentation, industrial workshops and summer student programs have been used to effect the transfer. This experience is discussed and the future outlined.IntroductionComputer simulation has become a common tool in many different fields of human activity during the past two decades, as illustrated in Figure 1. The total number of articles abstracted in Chemical Abstracts under the general subject entry of “Simulation"" has been following a pseudo-exponential growth since 1972 and was approaching 5000 in 1980, whereas no such entry was even used prior to 1967. This represents over a dozen papers published daily on the subject and should continue to grow to higher figures. Still, progress toward accepting modelling and simulation in mineral and coal processing has been very slow. It will be shown later that this slow acceptance is a cause rather than a consequence of the limited success of the various attempts made so far to draw unambiguous benefits from simulation applications. The real cause of the difficulties in fully accepting the new methodology lies in the multidisciplinary aspect of modelling and simulation, which does not suit the traditionally conservative approach that prevails in designing and operating large and costly processing plants."

Jan 1, 1982

By Nicholas Bonderoff, Amily Xu

The evaluation of battery electric vehicles (BEVs) in underground mines involves comprehensive business case analysis beyond just the capital and operating costs of the equipment itself. BEVs demonstrate benefits from an EHS perspective, reduced mine ventilation costs, lower energy operating costs, reduced overall GHG emissions (dependent on the source of electricity), elimination of DPM, lower equipment maintenance costs, and reduced cooling requirements in deep mines. When including batteries and supporting infrastructure, BEV capital costs are approx. 80% greater than that of diesel equipment. The project economics are highly dependent on the cost of electricity and diesel fuel, and these can vary widely depending on the location of the mining operation. Battery charging and swapping methodologies must be evaluated as there are a variety of approaches that can be employed which vary by manufacturer and type of equipment. Careful consideration of the cycle times, charging methodologies, and location of the battery charging infrastructure is necessary. Specific operating conditions must also be taken into consideration. For example, the time for blast gases to clear will be increased by reducing ventilation flow, and the potential impact on production needs to be evaluated. Similarly, the electrical distribution system needs to be evaluated for peak loading conditions when BEVs are charging. Criteria including maintainability, reliability, commercial availability, and performance need to be evaluated. BEVs have fewer components than diesel equipment and this correlates to lower overall maintenance costs, however, BEVs require maintenance personnel with specific skill sets in order to maintain the equipment. Battery lifecycle costs need to be considered as battery replacement incurs significant capital expense. Some manufacturers offer services to offset these capital costs through usage agreements. Recycling and disposal of batteries at the end of their lifecycles also need to be considered. With the increased selection of BEV equipment that will be available in the next 2-4 years, 100% BEV adoption is also possible. We recommend a holistic approach when evaluating BEVs for underground mines. This will ensure that everything is considered in order to evaluate the full impact of BEV implementation.

Jan 1, 2023

By C. S. Touchard, F. Bourgeois, L. Cassayre, Julcour-Lebigue C.

Developing a hydrometallurgical process that can overcome the refractory nature of chalcopyrite (CuFeS2) to leaching still eludes the minerals industry, despite major research efforts spanning decades. The several leaching experiments of this ore in sulfuric acid tend toward the same conclusion that the precipitation of elemental sulfur or iron containing species are the main dissolution inhibitors. Describing both the electrolyte composition and the various solid phases in equilibrium for the Fe-H2SO4-H2O system is essential to overcome this issue and to find an operating window. According to the thermodynamic models and to the thermodynamic data, we demonstrate, in this study, the need to use the Specific ion Interactive Theory (SIT) model to describe complex electrolytic systems through a limited number of parameters. Hence, the binary interactions for our case study have to be defined and estimated. This work develops a methodology to determine these parameters of the SIT model up to 90°C and an acid concentration of 1 mol/kg from published data for H2SO4-H2O and Fe(II)-H2SO4-H2O sub-systems or from new experimental data for the Fe(III)-H2SO4-H2O one. This method will eventually be applied to copper systems to lead to a thermodynamic description of the complete CuFeS2-H2SO4-H2O system. INTRODUCTION A leaching process consists in the dissolution of a solid phase into an aqueous medium in order to extract compounds of interest. It is a key step in the hydrometallurgical processes used in the primary production and recycling of metal components. One of the main leaching issues is the formation of passivating layers on the surface of solid particles, whose consequence is a partial or total hindrance of the dissolution. The leaching of chalcopyrite (CuFeS2) in sulfuric acid is a prime example. No industrial solution for the atmospheric pressure leaching of this ore has been developed to date because of passivation phenomena caused by the formation of elemental sulfur or iron-containing precipitates on the surface of the particles (Li, Kawashima, Li, Chandra, & Gerson, 2013). In the 1970s, the Pourbaix diagrams established for the Cu-Fe-S-H2O system at 25°C for low concentrated solutions (Garrels & Christ, 1965; Peters, 1976) agreed that copper and iron are fully dissolved at high potential and in acidic medium (pH < 4). However, they neglected the many stable solid phases that can form in these conditions. In addition, the Pourbaix diagrams of chalcopyrite in water, calculated with two recent databases (FactPS and Thermoddem 2017) associated to FactSage and PhreeqC softwares respectively, show large discrepancies at 75°C (Figure 1). Indeed, at high potential, FactSage predicts the formation of goethite FeOOH at a pH value of 1, while PhreeqC predicts the formation of jarosite (H3O)[Fe3(SO4)2(OH)6] for pH greater than 2.5.

Jan 1, 2019

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By S. Fox, Y. Fujita

Increasing demand for rare earth elements (REE) is expected to lead to new development and expansion in industries processing and or recycling REE. For some industrial operators, sending aqueous waste streams to a municipal wastewater treatment plant, or publicly owned treatment works (POTW), may be a cost effective disposal option. However, wastewaters that adversely affect the performance of biological wastewater treatment at the POTW will not be accepted. The objective of our research is to assess the effects of wastewaters that might be generated by new rare earth element (REE) beneficiation or recycling processes on biological wastewater treatment systems. We have been investigating the impact of yttrium and europium on the biological activity of activated sludge collected from an operating municipal wastewater treatment plant. We have also examined the effect of an organic complexant that is commonly used in REE extraction and separations; similar compounds may be a component of newly developed REE recycling processes. Our preliminary results indicate that in the presence of Eu, respiration rates for the activated sludge decrease relative to the no-Eu controls, at Eu concentrations ranging from <10 to 660 µM. Yttrium appears to inhibit respiration as well, although negative impacts have been observed only at the highest Y amendment level tested (660 µM). The organic complexant appears to have a negative impact on activated sludge activity as well, although results are variable. Ultimately the intent of this research is to help REE industries to develop environmentally friendly and economically sustainable beneficiation and recycling processes.

Jan 1, 2016

By N. Torres, G. Melcher

"An alternative to building new copper smelters, because of either stringent environmental regulations or in order to expand current plant capacity, could be achieved through the retrofitting of old reverberatory furnaces by making use of tonnage oxygen. The CONTOP® technology offers unique advantages over other techniques for this purpose, especially regarding substantial reduction in bath, capital and operating costs. This is possible to achieve since the reverb throughput could be largely increased with no major structural modifications to the furnace.The following options are offered to the smelter operators: dirty concentrates can be treated in an adjacent Contop system, or the cyclones can be mounted on the reverb roof for either dual operation or full Contop operation. ln the tatter case the furnace will be used as a settling chamber and f or slag c1eaning by top blowing with reducing gases.By incorporating Contop technology, the furnace throughput can be increased, higher malle grade, fixation of sulphur from furnace off-gas and substantial savings in energy consumption are possible to attain.IntroductionCopper smelting has been revolutionized during the last quarter century to such an extent that the standard type of plants consisting o f roasters and reverb furnaces seem a thing of the past, or almost. Though the building of new, more energy efficient smelters is a very likely opportunity for a grassroots plant, it would be hardly justifiable to replace an old existing plant unless there are heavy environmental or economic constraints(1,2,3)."

Jan 1, 1984

By Ward G. Wilson

Best practice in the design and construction of soil cover systems for mine waste management has advanced extensively over the past two decades. While significant progress has been achieved, we still have little experience with respect to proven performance for cover systems that must last hundreds of years. Some cover designs appear to be functioning well, while at the same time the performance of many more are now being called into question. This presentation evaluates the integrity of cover systems from both a global and local perspective in relation to the uranium industry within Canada.

Aug 1, 2010

By Theophile Yameogo

Much has been said about the methodology of geomechanical design in underground excavations. However, the geological, hydrogeological and geotechnical complexities encountered at the production horizons in the Athabasca Basin commanded for a novel approach in the geomechanical assessment and design of underground openings. Rock mechanics engineers at Cameco McArthur River have been able to establish a practical methodology that goes beyond known conceptual approaches. In this paper, the author describes the original challenges and unique approach in the geomechanical assessment for drifts and chambers development. The example of the successful development of the 510-8225N Chamber will also be presented.

Aug 1, 2010

By P. G. West-Sells

At Barrick&apos;s Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

By S. H. Logan

The present discussions throughout the civilized world on the subject of gold for monetary purposes may seem due to general economic conditions during the past year. But for some years previously a small group of authorities had warned the world against the continued disregard of an equitable distribution of existing gold reserves, and had urged the necessity of keeping the supply of new gold equal to the monetary demand, which, according to world production and trade figures, increases on the average about 3 per cent per annum. In 1927, Sir John Aird, the President of The Canadian Bank of Commerce, stated that the United States could spare a billion dollars of the supply it then held, 4 ½ billion dollars. About a year and a half ago the Professor of Banking and Currency in the University of London, Mr. T. E. Gregory, said, "If the world finds it impossible to modify its habits so far as to make an organized effort to economize gold seem less Utopian, it must be prepared to pay for its bad habits, in this and other respects, by a possible loss of material welfare." These clear-cut statements were not heeded, perhaps for one reason because most countries were in the flush of prosperity, and making such great demands upon the mining fraternity for industrial materials as to distract attention, at least to some degree, from gold mining. Now the world knows it faces serious problems, first, of making? fully effective its present monetary reserves, which, although badly distributed, are as a whole ample for the needs of the present, and secondly, of preventing a shortage in the supply of new gold, one that may come within the next few years if the present sources of supply are not enlarged, and if there is no marked change in the technique of gold production.

Jan 1, 1931

The total current inventory of mature fine tailings is estimated to be nearly 850 million m³. Pressure has come to bear on the industry to accelerate its tailings management practices and prevent this inventory from steadily growing. The present paper describes the treatment, management and reclamation of fluid fine tailings. New technologies being evaluated include: i) Thin layered - fines dominated deposits, ii) Deep - fines dominated deposits, iii) Fines enriched sand deposits, and finally iv) water capped disposal in end pit lakes. A brief overview for each of the methods of treatment and disposal for fluid fine tailings is provided.

Aug 1, 2013