Search Documents

By J. L. Gartshore

PRACTICALLY all of Quebec's chrysotile asbestos production derives from twelve mining and milling operations located in the "Eastern Townships" area of the province. The annual output of these twelve operations exceeds one million tons of chrysotile asbestos, valued at over one hundred million dollars, and is shipped to manufacturers spread over all six continental areas of the world. A total of approximately twenty million ton of asbestos ore yearly, or about seventy-five thousand tons a day, is mined. Individually, the operations vary in size from about two thousand tons to thirty thousand tons per day. Removal of waste rock and overburden to develop these ore tonnages varies greatly from one mine to another, but would probably average out at about a one to one ratio.

Jan 1, 1962

By Shinji Muraishi, Shinji Kumai, Yasutaka Kedo, Takashi Kambe

"Magnetic pulse forming (MPF) is one of the extreme high-speed forming processes. A metal sheet which is accelerated by electromagnetic force is collided onto a mold and fine and sharp details of the product can be obtained. The deformation mechanism of the MPFed metal cannot be understood only by the microstructure observation of the deformed metal. The deformation behavior of the metal should be investigated also by considering the local microstructure change with strain, strain rate and temperature change during deformation. Numerical analysis is an effective method to achieve this requirement. In this study, pure Al and Cu sheets were deformed by MPF. Impact velocity of the metal sheet was calculated by using ANSYS Emag-Mechanical. Based on the obtained impact velocity, the deformation behavior of the metal sheet was reproduced, and local strain, strain rate, and temperature were analyzed by using ANSYS AUTODYN. The relationship between the local microstructure change of Al and Cu sheets and the deformation parameters was examined.INTRODUCTIONMagnetic pulse forming (MPF) is one of the high-speed forming processes using electromagnetic force. Fine and sharp details of the product can be obtained, and springback after deformation is extremely reduced in comparison to the conventional forming processes(Psyk, Risch, Kinsey, Tekkaya, & Kleiner, 2011). Figure 1 shows a schematic diagram of MPF. A metal sheet is placed over the coil in the discharge circuit. The discharge current runs through the coil, and magnetic fieldis producedaround the coil. An eddy current is inducedin the metal sheet. Interaction between magnetic field and eddy current creates electromagnetic force. The metal sheet accelerated by electromagnetic forcecollides ontothe mold. Forming is completed in a few tens of micro-seconds.MPF is suitable for metals with a high electrical conductivity like Al and Cu.The MPFed metal may have characteristic microstructure because of high strain rate deformation."

Jan 1, 2018

By Jr. Wilkinson

Suncor Energy currently mines approximately nine hundred thousand tonnes of ore and waste per day at its open pit operations in the Athabasca Oilsands near Fort McMurray, Alberta. Modeling these deposits for planning purposes is particularly challenging given the characteristics associated with the deposit - stratigraphic deposition coupled with gradational grade distribution. The identification of ore and waste is a combination of bitumen cutoff grade, minimum mining thickness and separable waste thickness subject to criteria established by provincial regulatory agencies. Suncor along with Mincom Inc. have collaborated on this project to derive a methodology, automated by computer software, to streamline the ore and waste identification process. This paper explains the methodology and programs created to identify ore and waste in use at Suncor Energy and how this identification is used to categorize reserves and to generate mine design surfaces.

Apr 1, 2005

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada's current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today's commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By Ting An Zhang, Chengzhi Jiang, Xiujing Zhai, Feng Xie

The extraction and concentration of nickel from aqueous solutions by emulsion liquid membranes (ELMs) using tributylphosphate (TBP) as extractant has been investigated in this research. The emulsion liquid membrane consists of a diluent (kerosene), a surfactant (Span 80), a mobile carrier (TBP), and a stripping solution (ammonia solutions). Important factors influencing the separation process including membrane composition, feed composition, and mixing speed have been examined. The results show that more than 90% of nickel in the feed solution could be extracted by ELMs under the experimental conditions, indicating the feasibility to use the designated ELMs to detoxify nickel-containing industrial waste solutions.

Jan 1, 2014

By Bruce Regensburg

As trucks become larger and larger, haul roads take on a more significant role in mining costs and economics. The School of Mining at the University of Alberta has compiled a design manual for haul roads using both empirical and theoretical information. One section of this manual deals with the economics of haul road construction. While many mines look only at the construction costs of haul roads, this paper looks at all associated parameters including construction costs, removal costs, timing, truck productivity and width implications. The authors demonstrate the method to determine the most appropriate quality of road for different road conditions and life spans.

May 1, 2001

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By J. P. Nowlan

"This paper is an attempt to outline the structural problems at the Cochenour Willans mine, in so far as their details have been tentatively worked out. It must be emphasized that there are considerable data that can be interpreted in more than one way, and that further work may modify or completely change some of the hypotheses presented herein. Certain features, however, are sufficiently constant to warrant reliance on them when searching for extensions of orebodies.As the individual ore shoots usually have relatively small dimensions, but are often very high grade, structural details are of more than usual significance in laying out a mining programme. An illustration of this is a small shoot recently located and mined as a result of studying a minor slip cutting off a part of high grade gold ore in No. 319 stope. The shoot, which is bounded on three sides by slips, and on the fourth by the original stoping, was roughly triangular in plan, 20 feet on the base, and 40 feet in length. The average width mined was 4.5 feet, but the gold obtained totalled over 1,800 oz.The property lies in Dome township, east of McKenzie island, and consists of an original group of thirteen claims acquired from the Cochenour Willans syndicate, plus one additional group of five claims obtained by purchase from the Kelson Red Lake Gold Mines, Limited, and one other claim that rounds out the southeast corner of the block.The claims of the original group were staked by W. M. Cochenour, Dan Willans, and Horace Young, during 1926 and 1927. The Cochenour Willans Syndicate was formed in 1928, and until incorporation of the present Company work was carried on at varying intervals by several different interests, including Ventures Limited, Hollinger Consolidated, who sank a shaft to open up the 150-foot level, and by the Syndicate itself. The first ore from the property was shipped to the Gold Eagle mill by the present Company in 1939, and amounted to 4,959 tons, from which 2,360 oz. gold was recovered. The first brick was poured in December, 1939, and production has been continuous since that date. To the end of June, 1946, gold having a value of $5,982,000 has been produced from 345,033 tons of ore treated."

Jan 1, 1954

By D. G. Sediako

Chemical composition and the casting/rolling production routes determine the cost and properties of the wrought material. For example, the coarse-grained structure frequently associated with DC casting requires complex rolling schedules to refine the grain size. Hot forming (rolling/forging/extrusion) results in a strong crystallographic texture, which is responsible for the tension-compression strength asymmetry frequently exhibited by magnesium alloys. Understanding the influence of alloy composition on texture evolution during forming provides useful practical information to optimize industrial hot-forming technologies for magnesium alloys. In this study, a series of Mg-based alloys containing varying combinations of Al, Rare Earths, Zn, Ca, and Sr were subjected to identical casting and extrusion processes in order to isolate the effects of alloy composition on texture evolution. Textures were measured by neutron diffraction at the NRC Canadian Neutron Beam Centre. The ability of neutrons to penetrate deeply into materials allowed information to be retrieved from all regions of the bulk specimens without destructive and time-consuming sectioning operations, thereby providing true bulk texture data. {1010} , (0002), {1011}, and {1012} pole figures were generated for all of the as-processed alloys, from which Orientation Density Functions were obtained. The were then used to reconstruct the pole figures and to extract semi-quantitative texture data showing how the (0002) and {1010} planes align themselves with respect to the extrusion axis. It was found that varying the concentration of aluminum (3-4 wt%) and Rare Earths (2-3 wt%) in AE alloys had a weak effect on texture development. All of the alloys showed similar magnesium extrusion textures, in which the (0002) poles align themselves preferentially with the extrusion axis. The substitution of Sr for Rare Earths also did not have a significant impact on texture development. On the other hand, while the presence of small amounts of Zn and Rare Earths did not have a strong effect on texture development, alloys with higher concentrations of these alloying additions (in combination) showed an enhanced tendency for the {1010} poles to align themselves with the extrusion axis. The addition of Ca also enhanced the alignment of the {1010} poles with the extrusion axis. These textures can complicate further processing and introduce a significant anisotropy that could influence creep properties.

Jan 1, 2007

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By Gordon L. Kidd

The object of this paper is to show the relations of the East Coulee coal area to the near-by Willow Creek, Wayne, Rosedale, and Drumheller areas, all being parts of the Drumheller field. The word ?area? is here used in a more local sense than that employed by Dr. J. A. Allan, whose. 'area' is rather comparable with the 'mining division' in British Columbia. I have drawn freely from the published information, particularly from Dr. Allan's report on the "Geology of Drumheller Coat Field, Alberta", and from Dr. E. Stansfield's paper on " A Chemical Survey of Alberta Coals", to whom thanks are due. The Drumheller field is served by branch lines of the two principal Canadian railways. The C.N.R. traverses the district by its Goose Lake line from Calgary to Saskatoon; and the C.P.R. by a line from Calgary to Acme and then southeasterly to Drumheller, where it effects a junction with the C.N.R., over which the C.P.R. has running rights as far as Rosedale. From Rosedale, a joint line built during the summer of 1928 extends about forty miles down the Red Deer river to the mouth of Bull Pond creek. From that point the C.P .R. turns more southerly to connect with the Bassano-Empress line. The C.N.R., it is expected, will eventually proceed eastward to connect with a transcontinental line. The joint line from Rosedale down the Red Deer river opened up the Willow Creek and East Coulee areas.

Jan 1, 1929

By Asbjørn Solheim

The service life for aluminium reduction cells is often limited by the cathode carbon, due to preferential wear along the periphery of the cell leading to the so-called "W" wear pattern. The reason for this preferential wear is not well understood. Two mechanisms are suggested in the present paper; 1) non-stationary dissolution of aluminium carbide into a layer of sludge that periodically forms and disappears, and 2) electrochemical formation and dissolution of aluminium carbide within an aluminium carbide layer containing bath-filled pores. The latter mechanism may be related to the high local current density at the periphery of the cathode.

Jan 1, 2011

By Nathan Deisman

Coupled reservoir geomechanical simulations have become a key component of caprock integrity assessments for SAGD operations. This work demonstrates the differences of stress evolution when considering coupled versus uncoupled reservoir simulation. Coupled simulation involves the use of a reservoir and a geomechanical simulator with feedback to each simulator to update reservoir or geomechanical variable (permeability, porosity, relative permeability, pressure, temperature, saturations). Uncoupled simulation only passes the pressure and temperature to the geomechanical simulation with no reservoir simulator updating. Therefore, it is possible to complete uncoupled simulations exclusively with no knowledge of geomechanical flow property evolution. However, it is important to understand the differences between the stress evolution in each model for caprock integrity analysis. A single geological model was selected and parametric analysis was completed while varying the geomechanical the production injection pressures (1600 kPa, 1900 kPa, 2200 kPa) for a reservoir with an initial pressure at the injector of 1300 kPa. The results of the six uncoupled and coupled models are compared through the changes in mean stress, shear stress, and strength with focus on geomechanical assessment of caprock integrity.

Jun 1, 2012

By E. O. Chisholm

Synopsis The colour changes effected in a solution of dithizone by trace amounts of copper, lead, and zinc mineralization provide a sensitive field test for these metals. The method has been used with success by the United States Geological Survey to trace zinc orebodies under residual soils. The dithizone test is used here on samples of non-residual soil overlying a gold-bearing zone in which the gold is associated with disseminated sphalerite, galena, and chalco-pyrite. A gold-bearing zone was successfully traced under overburden ranging from a few inches to five feet in depth by means of this method. The method may prove useful in guiding preliminary trenching through light overburden, by outlining the extent of copper, lead, and zinc mineralization. Introduction The dithizone test affords a rapid, simple, and delicate test for the presence of zinc in soil and water and is suitable for use under field conditions. It has recently been used with success by the United States Geological Survey to outline a zinc-rich area in the residual soil over a primary zinc deposit in Tennessee. The purpose of the present study was to ascertain whether the method could be used to trace a gold-bearing zone, containing associated zinc mineralization, under shallow, non-residual, glacial overburden. The results obtained indicate that the method can be used to guide preliminary trenching in overburden up to six feet in depth. Tests made of the water near lake-shore outcrops also indicate that favourable prospecting zones may be located from the water, within five feet of the shore. It is felt that this simple field test should find a wider use in prospecting, because, under certain conditions, it can outline favourable zones and thereby reduce the amount of blind trenching necessary. The following pages describe the type of deposit tested, the method used, the .results obtained, and the difficulties encountered by a novice in the use of this chemical procedure. The author is indebted to the officials of Nor-Penn Mines, Limited, for their co-operation while the tests were being made; to the late Richard Bouska, Kenora prospector, for helpful suggestions; and to F. W. McCamus, University of Toronto undergraduate student, who ably assisted with the work.

Jan 1, 1950

By P. Fleming, W. Pascheto

"Rod mills processing nickel and copper ore experienced recurring failures of liner bolts. In some cases failures became very frequent, requiring constant mill intervention and consequently impacting process stability and operating costs. Investigation related to the causes of bolt failures involved a multidisciplinary approach with the participation of engineering, maintenance and operation. It included the determination of bolt failure mechanisms as well as the assessment of mechanical properties, fabrication quality and handling and installation procedures. In addition, other parameters affecting bolt performance such as mill and liner design, operating parameters and maintenance practices were studied. This paper reports the failure investigation results and proposed solutions for failure prevention. INTRODUCTIONOccasional liner bolt failures are common in rod mills. However, chronic bolt failures developed in rod mills processing nickel and copper ore caused frequent shutdowns for bolt replacement to an extent that affected process stability. At first, it was thought that the cause of recurring failures was related to bolt quality. The operation then submitted several failed bolts to failure analysis. However, it became apparent that bolt quality was unlikely to be the main cause of failures. The determination of root cause (s) then became more complex, requiring a multi-disciplinary approach to failure investigation, requiring the assessment of bolt installation methods, mill design, operating conditions and maintenance practices. The results of the metallurgical failure analysis and investigation of other possible causes of failures are reported here."

Jan 1, 2016

By T. I. . I. Sibbald, D. E. Jiricka

The Goldfields area on the north shore of Lake Athabasca , was active in the thirties and early fortie . In 1934, Tom Box discovered gold mineralization in quartz veins in pyritized 'granite' at the ite of what wa to become the Box Mine of the Consolidated Mining and Smelting Company of Canada Ltd . In the rush of activity that followed numerou other gold occurrences were found. the most significant of the e being the Athona and Frontier prospects which underwent underground development bur did not reach production. Probable reserve identified to date in the Box and Athona deposits amount to some 3.5 million ton grading an average 0.ITT oz gold/ton . Some 10 to 15 million tons of lower grade, po ible reserve are also reported at the Box. From 1939 to 1942, the mine produced, from underground , 64,066 ounces of gold from ore grading 0.0452 oz gold/ton at a cost of between $1.5 and $2.0 a ton. The Goldfield area is underlain by upracrustal rock intruded by mafic bodies and invaded by ·granite'. The upracru tal . thought to be of Lower Proterozoic age are characterized by a helf-type ucce ion metamorpho ed under lowermiddle amphibolire facie conditions into quartzites, quartz-mica chi ts. dolomitic marbles, diop idic calc-silicates and cordierite-anthophyllite-biotite schi t . Amphibolites of presumed igneou origin form concordant to subconcordant units up to a few ten of metre thick in the upracrustals and occur as le regular masses in the 'g ranite·. Compositionally they vary from gabbroic to granodioritic. with the more mafic varieties being most common. Granitic rocks exhibiting a variety of textural , structural and compositional characteristics underlie most of the area. Four main units are recognized: foliated (older) 'granite', 'leucogranite', feldspar augen 'granite· and pyritic mine 'granite', however, in geological mapping the e are somewhat arbitrarily differentiated due to transitional relationships and admixture of types. Although there is no unambiguous age data available for the e 'granite ' adjacent northshore 'granite' of geologically similar age yield Rb-Sr isochron dates around 2000 Ma. The area is characterized by two major deformation events of which the earliest gave rise to the dominant regional foliation and to rare minor and outcrop scale folds. This foliation which in general parallels compositional layering is folded into the major Goldfields syncline, whose axis plunges weakly to moderately outh. Related open minor folds have subvertical axial surfaces which are locally paralleled by a weakly defined schistosity. Most rock display a pronounced rodding fabric, coaxial with second fold axes and apparently the product of this deformation event. However, a note of caution is introduced into this interpretation, as the rodding fabric is also parallel to first fold axe .

Jan 1, 1986

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014