Search Documents

By P. Personnet, D. Wheaton, E. Couzinie, V. Demetriou, Brooks. W., G. Girault, M. Meyer, L. Charbonnel

A common problem in Gas Treatment Centers (GTC) from primary aluminium smelters is the temperature of the gas to be treated : above a threshold, filtering media are irreversibly damaged. The traditional way of dealing with high gas temperature is to dilute with fresh air, which implies over sizing - and therefore higher cost for - the GTC in order to have the capacity to treat this dilution air without compromising on pot suction. A system was developed which decreases gas temperature without having to use dilution air. This system is based on water pulverization in gas collectors. The water vaporization leads to a temperature decrease of the gas. A pilot system was trialed in our R&D unit. Satisfactory results led to the development of an industrial system based on Envirocare equipment (partnership), which was trialed in our production plant in Tomago (NSW, Australia). This patented system was then generalized in this plant, which is now using it with success during austral summer.

Jan 1, 2006

By C. D. Anderson, C. G. Anderson, P. R. Taylor

"Rare Earths have become critical for our energy and materials driven society. While primary production must ramp up to fill growing demands, the recycle of these strategic elements must also be initiated. This paper will outline the potentials of and metallurgical technologies employed for Rare Earths recycle from various secondary sources.INTRODUCTIONWhen investigating the recovery of rare earths from secondary sources it is necessary to understand the nature of the sources to be processed. As of 2009, the USGS reports the distribution of rare earths by end use, in decreasing order, was: chemical catalysts 22%, metallurgical applications and alloys 21%, petroleum refining catalysts 14%, automotive catalytic converters 13%, glass polishing and ceramics 9%, rare earth phosphors for computer monitors, lighting, televisions 8%, permanent magnets 7%, electronics 3%, and others 3% (USGS, 2011). Additionally, it is reported that the amount of recycling was quite small and consisted primarily of rare earth magnet scrap, although with the sharp increase in the price of rare earths, and the potential shortage in supply, focus in this area is continually growing. Thus, the opportunities, whether realistic or not, are extremely vast in the recycling of rare earth containing materials. The following subsections will present methods proposed for the recycling of rare earths based on the feed material type.RECYCLING OF RARE EARTH MAGNETSCurrently, investigations are ongoing in the area of recycling production scrap and end-of-life materials in the rare earth magnet industry. The following techniques illustrate potential methods for the recovery of rare earths from secondary RE magnet sources.Recycling of Rare Earth Magnet Sludge by Selective ChlorinationDuring the production of neodymium magnets, a by-product of production is the so called “magnetic sludge”. This by-product contains high amounts of neodymium, thus a process for the recovery of Nd has been proposed. In this process the Nd present is selectively chlorinated/distilled by the addition FeCl2 via the following reactions."

Jan 1, 2012

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By Christopher Boys

"Abstract -Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized . These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. ln this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dis­ solving huge cavities in the evaporites . The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds . ln at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation .Geological indicators of the proximity of an anomaly may include: a change in Insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore zone, and drops in topography >10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies.Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By M. Ruel

In today's highly competitive worldwide market, it is becoming extremely important for managers to make sure that all resources are used where needed the most. That way, all resources are generating added value, process control equipments are maintained in an optimal state for best performance, and final product is produced at least cost. Performance monitoring is the only way to ensure that everyone is working on top priorities toward the same goal. How can we add value to these warehouses of data? The data is there and the information is hidden; it is just waiting to be extracted. A process performance monitoring system is able to determine if a loop, a system, a unit, or a plant meets the expected performances. The system prioritizes the areas that need attention. It also provides historical reports of the plant status by areas, by loops, and by identified problems. This information is provided to different categories of users in an appropriate format for each one. The system also includes diagnostics and tools to detect and analyze problems.

Jan 1, 2007

By Owen Owens, W. P. Armstrong

Abstract- The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors' experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

By W M. Cameron

Geophysical studies have extended seaward in recent years, and the important discoveries which have been made have led to a better understanding of geological processes. A present source of certain minerals, the sea will eventually serve as an important source of desalinated water. The continental helves, in particular, represent a potential mineral resource. The expansion of Canadian oceanographic effort that is now underway will eventually lead to the exploitation of the wealth beneath the sea. THE subject of this symposium, which emphasizes the word "geophysics," the specialties of the speakers who are contributing and the nature of the audience at first made me believe that I, a a physical oceanographer, would be out of place. However, I shall undertake to classify myself as a geophysicist, and shall arrange my remarks on my specialty o that they might be of interest to those of you who are predominantly geologists, metallurgists or mining engineers.

Jan 1, 1963

By Ltd Changsha Research Institute of Mining and Metallurgy Co., Shi Yunliang, Luo Yunbo, Chen Jun, Liu Miaohua, Xiao Jinxiong, Long Yan

"A refractory lead-zinc oxide ore located in Yunnan has hundreds of tons of metal reserves, which is hard to be recovered effectively by conventional oxide ore beneficiation methods. In this study, by sulfidation roasting of raw-ore, sulfide deposit is formed on the surface of the lead-zinc oxide ore, and then the roasted ore is processed with bulk flotation. The test results indicate that a bulk concentrate with grade of 7.85% lead and 34.24% zinc, recovery of 79.13% lead and 79.04% zinc, respectively, can be obtained by using conventional sulfide ore flotation method.The sulfidation process shows that pyrite in the raw ore releases S firstly, then S reacts with PbO and ZnO to transform into PbS and ZnS. When the mole ratio of sulphur:zinc is 0.59, the surface of smithsonite is covered with a layer of zinc sulfide. When the mole ratio of sulfu:zinc rate is 1.47, entire simthsonite particle is transformed into zinc sulphide. Thus the transformed particles can be recovered by flotation without complete sulfidation.INTRODUCTIONWith the increasing demand for zinc and decreasing of zinc resources, people pay more attention on development and utilization of zinc oxide ore. However, zinc oxide ore has wide range mineral kinds, complex mineral composition, disseminated fine-grained particle size, and high content soluble salt, so current study results about the zinc oxide ore with conventional flotation are not satisfactory. So far, process dealing with zinc oxide ore includes: sulfuration (Na2S)-flotation, direct flotation with fatty acids collectors, metallurgical methods, in which sulfuration flotation is the most widely used method. The basic principle of sulfuration flotation method is firstly roasting oxide ore with vulcanizing agent, and then recovering the sulfurated oxide ore with flotation, which is similar with recovering nature sulfide ore by using conventional collectors such as amines and xanthate."

Jan 1, 2016

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By E. J. Wasp, T. L. Thompson, T. C. Aude

The paper will deal with some of the more important technical aspects of slurry pipelines as they apply to the mineral field. In addition, the use of these technical concepts in arriving at realistic economic figures will be discussed.

Jan 1, 1970

By Kurt Tischler

This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry ? We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues.

Jan 1, 2012

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970

By P. K. Gummer

Gold was fir t di covered on the Seabee property in 1947 by the Con olidated Mining and Smelting Company Limited. Acquired by Claude Resource Inc. in 1984, the property is now being explored by Placer Development Ltd . in joint venture with Claude Re ources. Between Augu t, 1985 and March, 1986, Placer completed 54 drill holes, extending the main o. 2 and o. 5 vein y tern to a depth of 1000 feet below surface and di covering two new satellitic gold zone 800 feet west of the o. 5 gold zone. Drill proven and probable geological re erve in four zone ( os. 2, 5, II, 14) to a vertical depth of 1000 feet, are approximately 1,120.000 tons averaging 0.32 oz. Au/ton.

Jan 1, 1986

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

By G. A. Peebles

"This paper describes the various types of radiometric instruments and the techniques of their operation for grade control, sampling, assaying and probing drill holes at Eldorado Nuclear's uranium mine in northern Saskatchewan. Modifications that have been made to these instruments are discussed, and suggestions are made for the development of more refined and specialized radiometric equipment."

Jan 1, 1969

By D. R. Murray

"A promising long-term solution to uranium tailings reclamation has been the establishment of vegetation directly on the waste material. The soil profiles of areas vegetated for 0, 3, 8 and 10years are characterized as to the extent of soil development . The characteristics are compared with the visually interpreted soil profile. Organic matter content is presently the best analytical judge of soil development. Vegetation procedures have produced a build-up of organic matter in the top 10cm of tailings where natural microbial populations flourish. The CN ratio is high and the profile depth shallow, suggesting the need for additional fertilizer applications.IntroductionThe reduction of surface erosion and improved aesthetics of uranium tailings has been accomplished by the establishment of a vegetative cover. In 1971 research concentrated on developing methods of plant establishment at minimal cost and soil amendments on uranium tailings in Elliot Lake , Ontario. One process of stabilization used on a large scale was direct seeding of grasses and legumes into the tailings which had received only limestone and fertilizer treatments. Fertilizer additions were made for varying lengths of time in subsequent years to maintain the established cover.Maintenance-free vegetation would be possible once a soil profile developed with sufficient nutrient recycle and plant regeneration capabilities(1). Tailings vegetated in 1971, 1973 and 1978 that had received either 3 or 5 years of maintenance fertilizers were examined for soil development profiles. The extent of soil development and the relative effect of time and fertilizer would provide direction on reaching the goal of a self-sustaining cover.This paper is an abridgment of Division Report MRP /MRL 81-126 of the same title(2)."

Jan 1, 1984

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002