Search Documents

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By J. Grant Spratt

THE Turner Valley gas-field, situated some thirty miles southwest of Calgary, Alberta, has been the topic of much discussion, particularly from a geological viewpoint. Several papers (1, 2, 3, 4, and 7) dealing with the structural and stratigraphical geology have already been published and are available for reference(l). In this article, the geological conditions will be treated only as they directly refer to the crude-oil prospects along the west flank of the anticline. HISTORY During the past twelve years, Turner Valley has been known mainly as a field which has produced a high-gravity naphtha from relatively large quantities of gas. For about ten years prior to the discovery of this naphtha-bearing gas, which is produced within the upper 450 feet of a dolomitic limestone of Carboniferous age, a minor production of light crude-oil was obtained from overlying sands of Cretaceous age. Up to June 1st of the present year, the field had produced 9,473,582 barrels of naphtha from approximately 829,000,000 M.c.f. of gas. For the past four years, the total daily production of 80 to 90 wells has averaged about 3,200 barrels of naphtha from 250,000 M.c.f. of gas. This is an average of 13 barrels per million cubic feet. The naphtha is extracted from the gas by ordinary gas-oil separators and absorption plants. After the naphtha has been recovered, about ten per cent of the gas is marketed for fuel to supply the cities of Calgary and lethbridge and intermediate cowns. The remaining ninety per cent is burned to the atmosphere, with the exception of some four to five million cubic feet per day which the Calgary Gas Company score in the depleted Bow Island gas-field.

Jan 1, 1936

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

By M. Cousineau, S. Gariepy

"Current business and corporate environments push for improving metal accounting practices in smelters. The ensuing projects commonly proceed along a bottom-up approach. As such, efforts are first put on reviewing the measurement system and then on remedying the identified weaknesses. The focus is thus moved to mass/metal balance only after the measurements upgrade process has been completed. However, practice has shown that assessing the high variances related to suboptimal measurement processes is complicated without the help of statistical data reconciliation. This bottom-up approach leads to a to-do list that can not only exceed available resources but also lack prioritization in view of achieving the targeted end use. This paper describes an upgrade project done differently where all the three dimensions of the metal accounting system: hardware, software, and people were instead involved at the onset. Personnel was thus trained on data reconciliation software at the beginning of the project to make the reconciled mass balance benefits available earlier in the upgrading project. This has pinpointed the most critical measurements where accuracy and reproducibility should be improved. Overall, not only the instrumentation retrofitting process has been streamlined, but the global risk for the whole upgrading project has been significantly lowered.INTRODUCTION Mining companies are pressured to improve their production accounting practices in response to the strengthening of corporate requirements for timely and accurate production reporting (Gaylard, Randolph, & Wortley, 2014). Smelters are not spared from these changes. However, their unique situation in the mining value chain set them as strategic targets for upgrading projects. They usually have a longer lifespan than concentrators thereby offering an extended lifecycle to justify investments. Furthermore, numerous smelters have toll agreements with third parties. Accurate cost and production accounting is, therefore, a vital piece of information to fix acceptable contract conditions. Mining companies are ultimately aiming at a clearer view of the operating performance of each business unit to improve their business decisions in a competitive environment. This sought for increase in visibility through plant performance can only be achieved through an upgrade of the metal accounting system. Figure 1 shows the different components of a state of the art system (Gaylard, Morrison, Randolph, Wortley, & Beck, 2009)."

Jan 1, 2017

By Sergio Romo, Gerardo Fuentes, Adriana Garcés

Refractory ores with gold entrapped in a sulfide matrix, must be processed in a first stage with chemical or physical treatment in order to liberate the gold for a subsequent step with cyanide. The goal of this research was to compare the refractory behavior of a gold concentrate treated using two pretreatment methods: pressure oxidation and fine grinding. Gold concentrate from Viacha Mining in Bolivia, assaying 50.11 gpt, with a P80 of 131 ?m was used. The concentrate contains arsenopyrite and pyrite as main sulphides in the matrix. A preliminary test with cyanide resulted only 13.5% of gold extraction with 4 hours of stirred leaching. Using an autoclave oxidation with sulphuric acid and 12 bar oxygen pressure at 220°C pretreatment, the cyanide gold extraction increased to 69.0% in 4 hours. When material was ground in a pulverizer, producing a P80 of 20 ?m and the product directly cyanided, stirred leaching gave a gold extraction of 65% in 4 hours. For both techniques, the effect of temperature, sulfur produced in autoclave oxidation, optimization of the cyanide and the nature of residues were also studied.

Jan 1, 2014

By M Reza Afshar

In this work a mathematical model was developed to study the effect of electromagnetic force on the magnesium melt containing nonmetallic inclusion in an electrical isolated channel. The electromagnetic force exerted on the inclusion induced by DC current field was calculated. A three dimensional turbulent flow equations were solved numerically to compute the velocity field within the channel. On the basis of computed velocity and magnetic fields, the trajectories of inclusions were calculated using the equations of motion for inclusions. Parametric studies were carried out to evaluate the effect of various parameters such as current density, channel diameter and particle density on the removal efficiency of inclusions from magnesium melts.

Jan 1, 2004

By Krishna Parameswaran

In this paper, we attempt to answer an often asked question, how can metal mining be compatible with the principles of sustainable development. Starting with the classic Brundtland Commission definition of sustainable development as "development that meets the needs of the present without compromising the ability of future generations to meet their own needs," we make the case that mining is or should be sustainable, using examples of sustainable practices at ASARCO LLC, an integrated U.S primary copper producer. These examples cover the entire mining cycle starting with exploration, mining, beneficiation, smelting, refining, closure and post-closure and post-mining land use. It is hoped that the presentation will challenge the mining industry to even greater innovation as future mineral development projects are planned.

Jan 1, 2015

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By G. E. Peacock

SIGMA MINES is situated in the township of Bourlamaque, Abitibi County, Quebec. It is a gold producer, and presently treats an average of 1,200 tons of ore per day, at a grade of approximately 0.18 oz. per ton recovered. The mill started operations in March, I937, at a rate of 300 tons per day. This was increased to 800 tons in I940, and to 1,000 tons by I943. The rate was cut back during the war years, but was brought back up to capacity by I948. The mill tonnage was in-creased to the present 1,200 tons per day in I960. The underground workings are serviced through No. 2 Shaft (Figure 1), which, with 24 operating levels, extends from surface to a depth of 3,317 feet. When depth exploration was decided upon, two possibilities were considered: (a) deepen the main shaft by1,000 feet; (b) put down a winze for the same distance.

Jan 1, 1962

By M. A. Stogran-Baker, S. Cole

"Fluorspar mining occurred in the St. Lawrence area from the 1930s until the mid 1980s. In 2013, CFI discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods. A new mill was designed to produce 200,000 tonnes per year of high quality, acid-grade fluorspar concentrate. The simple mill flowsheet includes crushing, dense medium separation (DMS), grinding, sulphide flotation, pulp thickening, fluorite flotation, thickening, and concentrate filtration. The type of flotation cell used is being installed for the first time in North America. Site clearing commenced in the spring of 2016, followed by mill building erection completed by the fall of the same year. Civil and mechanical installation as well as site-wide construction was completed by the end of September 2017. Commissioning commenced, and at the time of paper submission mill production is on track to ramp up to full capacity by the beginning of 2018. This paper will focus on the use of fluorine NMR analysis applied to fluorite and the development of on-stream analysis, flotation cell selection and the decision to install the new cells, and the water control program designed to maintain process control with the least possible environmental impact.HISTORY St. Lawrence is located on the south-eastern coast of the Burin Peninsula in Newfoundland and Labrador. The first occurrence of fluorspar in the St. Lawrence area was recorded in 1843 by British geologist J.B. Jukes (DNR 2010). Fluorspar was likely extracted in small quantities prior, however commercial fluorspar mining did not commence until 1933 at the Black Duck Mine. The Black Duck Mine operation processed ore by washing and screening – acid-grade was hand-picked from the oversize, the undersize was sold as a lower grade product. The Black Duck Mine was closed in 1941 (Wilson 2010). The American Fluorspar Limited (New Fluor) commenced operations on the Director vein in 1936, and was bought by Alcan in 1942 (Cooper 2012). Alcan also developed the Iron Springs as well as the Tarefare deposits. The Black Duck Mine mill had closed, and a new mill was built. This new mill crushed the ore prior to dense medium separation, the sinks of which were sent to Quebec for use in Alcan’s aluminum smelter (CFI 2016). Alcan shut down it’s mining operations in 1977 due to the dropping price of fluorspar as well as labour disputes. In 1986, the British-based Minworth Limited began producing ore from underground at Blue Beach North and Blue Beach South, as well as from open pits at Tarefare and Director veins (Cooper 2012). A new mill was built by Minworth in order to process the ore using flotation to produce an acid-grade concentrate. The low price of fluorspar caused Minworth to shut down operations in 1990. Whilst exploration has been ongoing, no mining had occurred in the area since 1990."

Jan 1, 2018

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

The dissolution of chalcopyrite has received a significant amount of attention. The predominant paradigm of investigation is that its rate of dissolution is limited or passivated by a surface coating or film of material. The common candidates for such a passivating coating are numerous: polysulfide coating, metal deficient layers, copper sulfide coating, bornite layers, jarosite precipitates, and elemental sulfur films. While this line of explanation, that is, the explanation based on passivation, seems to have won some form of consensus with researchers, there is another explanation for the results that can account for all the results observed. Crundwell (1988) proposed that the solid state properties of chalcopyrite, in particular, the semiconducting properties, are responsible for the observed behaviour of chalcopyrite. The purpose of this paper is to outline the semiconductor mechanism of dissolution, and to show how this mechanism accounts for all the observed phenomena recently reported in the literature. The paper outlines the semiconductor mechanism of dissolution, shows how this mechanism accounts for the dissolution

Jan 1, 2014

By Chris Twigge-Molecey

"Over the last 50 years there has been a dramatic evolution in the metallurgical engineering field in Canada. In the 60s the field was dominated by large American and UK groups, often selling major process and equipment packages. The local content was limited to wrap around facilities and the civil and structural work. The mining and metallurgical companies had strong internal teams to lead these projects. Over the decades and business down cycles the large foreign contractors disappeared or re-structured and the mining companies largely shed their engineering and project management groups. The resulting gap was filled by a cadre of local specialist engineering companies, some of whom have grown to be world leaders in the field. The paper traces this evolution and examines the underlying causes and consequences."

Jan 1, 2015

By Farzad Mohammadi, David Kratochvil, Patrick Littlejohn

"With more rigorous regulations being enacted in the mining industry, a need exists for cost effective and environmentally compliant technologies to remove selenium from mine impacted waters to ultra-low concentrations. Existing selenium treatment methods have high life cycle costs, introduce risks of acute fish toxicity, and produce biological waste residues that represent future liabilities. Furthermore, achieving selenium discharge limits of less than 4 ppb is a challenge for existing technologies. Selen-IX™ is a technology developed by BioteQ that selectively removes selenium from mine impacted waters to less than 1 ppb. The technology is purely physico-chemical and takes advantage of the basic principles of ion exchange and electrochemistry. Unlike conventional electrocoagulation that removes suspended solids and breaks emulsions or oxidizes heavy metals, the electrochemical process employed by Selen-IX™ relies on creating conditions where iron acts as a highly effective reducing reagent transforming selenium from a dissolved species into elemental selenium bound in a solid phase. The iron-selenium by-product of Selen-IX™ is an inorganic, non-hazardous and chemically stable solid. Due to their high iron content, the solids produced by Selen-IX™ are of interest to the steel making industry as a low cost feedstock. This offtake potential can not only reduce the life cycle cost of selenium removal by reducing disposal costs but more importantly, eliminate the risk of future environmental liabilities. In this paper, the basics of Selen-IX™ technology are presented along with results of successful piloting on streams from coal and copper-gold deposits.INTRODUCTIONVarious contaminants are released into mining wastewater during the extraction and processing of metals. One such contaminant is selenium. A naturally occurring element found in rocks and minerals, mining activities accelerate its release into the environment. Selenium in trace quantities is essential to all life forms but at higher concentrations it can be harmful, especially to aquatic life where selenium bioaccumulation can lead to reproductive deficiencies."

Jan 1, 2016

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

By S. Yadav, T. G. Murthy, C. Saldana

"An experimental study has been carried out in order to study the deformation of porous brittle materials under plane strain indentation. Gypsum, which is well known model system for understanding the behaviour of soft rocks, is used in this study. The effect of wedge angle is investigated in this research through this series of experiments, using wedges of 3 different apical angles. High-speed, high-resolution images are captured using a CMOS camera during the experiment. The images obtained are analyzed using a Particle Image Velocimetry (PIV) algorithm in order to obtain the evolving velocity, strain-rate and strain fields.INTRODUCTIONThe problem of indentation, which is usually referred to in the context of hardness testing is ubiquitous as a material characterization technique for a large class of solids. Mechanical properties of materials such as yield stress, flow stress, fracture toughness, elastic moduli etc. can be related to the hardness of a given solid. The indentation problem involves a given material or solid (whose properties are to be determined) indented by a relatively harder material (indenter) allowing the solid to undergo plastic deformation, which is then related to the yield stress of the material. The problem of indentation and its variants see many applications ranging from mining and petroleum industry, infrastructure industry, manufacturing, and biomedical sectors. Indentation has been extensively studied in metals, with accurate measurement of deformation parameters, stresses and comparison with analytical solutions. On the other hand, understanding of indentation in other class of solids such as cellular solids, porous solids, rocks, and soft solids is still nascent. In case of rocks, a comprehensive understanding of the indentation problem is very crucial because of the obvious applications in mining, petroleum and infrastructure sectors. The inherent porosity, the brittle nature of the rocks, adds to the complexity of indentation in these porous brittle solids. Various theoretical models with degrees of simplifying assumptions have been proposed to study the indentation in rocks. The most common model used in the study of indentation in rocks is a cavity expansion model, wherein a blunt indenter indenting into a rock is approximated with the expansion of cylindrical or spherical cavity in an elastic-plastic material. Complementary studies in understanding fracture initiation and propagation due to indentation has been largely based on the studies of traditional brittle materials such as glass."

Jan 1, 2015

By W. G. Scott

IT IS APPROPRIATE that your Institute should have chosen, for its 1956 Annual General Meeting, the Capital City of a province which is making such rapid advances in mining. The railway industry is proud to be playing an active role in this development, expenditures on equipment and railway construction in the Province of Quebec alone in recent years being in ?excess of a quarter of a billion dollars. In looking up some background material for this address I ran across a definition of a mine by Mark Twain, the great American humorist, which I thought might amuse you. He said that a mine was "a hole in the ground owned by a liar". I am sure that if he were alive to witness the enormous value attached to Canada's mineral resources today he would quickly change his definition. Canada's postwar record of mining development has been staggering in its variety and enormity. Historically, only the ?construction of our transcontinental rail ways outranks the largest of three of these development projects - the aluminum undertaking at Kitimat; the Quebec-Labrador iron ore deposits ; and the petroleum and natural gas developments in Wes tern Canada.

Jan 1, 1956

By J. Gao

We present results from our investigation of the concept and practice of using surface-charged latex nanoparticles as building blocks for conductive membranes. Nanoparticles were synthesized by free-radical co-polymerization of two hydrophobic monomers, butyl acrylate (BA) and methyl methacrylate (MMA), a crosslinker, N, N'- methylenebisacrylamide (BIS), and a charged monomer, sulfonate styrene sodium salt (NaSS), in water. The resultant nanospheres were characterized with static and dynamic laser light scattering. Thin films were cast from concentrated particle dispersions, followed by incubation at ?110 °C. Conductivity, water uptake and final charge content were measured. The membranes have higher conductivities than both amorphous films cast from sulfonated BA-MMA-Styrene copolymer chains and BA-BIS-MMA-NaSS gel films. TEM images and neutron scattering spectra confirm the particulate structure of the membranes.

Jan 1, 2005