Search Documents

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By Ram Song, Yohei Harada, Shinji Kumai, Kazuho Otsuka

"Recently, vertical-type high-speed twin-roll casting (HSTRC) has been developed. The HSTRC shows extremely high cooling rates over 1,000 K/s even at the mid-thickness area. The fabricated strip has many metallurgical characteristics; super-saturation of alloying elements, fine solidified structure, and homogeneous distribution of fine constituent particles. In Al-Mn based alloys, the Mn alloying element can be supersaturated in the a-Al matrix and also form Mn-containing constituent particles during solidification. The Mn supersaturation and the distribution of primary/secondary particles in cast products affect the metallurgical behavior in the down-stream processing and can improve mechanical properties of the final products. In this study, Al-Mn based alloy strips were fabricated by HSTRC with various Mn contents. The solidified microstructure, constituent particles and its distribution, and Mn solubility were investigated in the as-cast condition. Due to the high cooling rate of HSTRC, fine constituent particles were homogeneously distributed, and coarse intermetallics were not observed. Mn solid solubility was estimated by electrical conductivity. The estimated Mn solubility was equivalent between strip surface and mid-thickness area.INTRODUCTION Al-Mn based alloys, as non-heat treatable wrought aluminum alloys, are widely used in packaging and heat exchanger for automobile industry. Besides Mn, Al-Mn based alloys often contain Fe and/or Si as alloying elements or natural impurities. During solidification, Mn can be super-saturated in the Al matrix, and also form Mn-containing constituent particles. Additionally, in the subsequent thermal-mechanical processes such as homogenization, rolling, and intermediate annealing, Mn in solid solution precipitates out of the Al matrix as secondary particles. The size, distribution, type, and the amount of dispersoids including constituent particles affect to texture evolution, recrystallization behavior, and final mechanical properties of wrought Al-Mn based alloys (Huang et al., 2016; Huang & Marthinsen, 2015; Engler et al., 1995; Muggerud et al., 2013). Therefore, controlling the initial level of Mn super-saturation and the distribution of constituent particles are important in the cast Al-Mn based alloys."

Jan 1, 2018

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

By O. A. Ojo, O. A. Idowu, N. P. Wikstrom, M. C. Chaturvedi

Transient Liquid Phase Bonding (TLP) of a Nickel base superalloy, Inconel 738, was performed to study the influence of holding time, filler gap size, and temperature on the joint microstructure. Insufficient holding time for complete isothermal solidification of liquated insert caused formation of eutectic-type microconstituents along the joint centerline region. An increase in the eutectic thickness with increase in initial filler gap size was observed in joints prepared at a constant temperature and holding time. In agreement with prediction by conventional TLP diffusion models, an increase in bonding temperature for a constant gap size, resulted in decrease in the time, tf, required to form a eutectic-free joint by complete isothermal solidification. However, a significant deviation from these models was observed in specimens bonded at and above l 175°C. A reduction in isothermal solidification rate with increased temperature was observed in these specimens, such that a eutectic-free joint could not be achieved by holding for a time period that produced complete isothermal solidification at lower temperatures. Considerable enrichment of the liquated insert with base metal alloying elements at higher temperatures is suggested to be an important factor contributing to the observed departure from conventional TLP prediction.

Jan 1, 2006

By C. A. Roloff

Demands for increased grinding production, lower-grade are and limited capital have resulted in ever larger grinding mills, some as large as 36ft (/1 m) in diameter and 12,000 hp (8,950 kw). The result is often f ewer machines per plant, with a greater dependence on each machine. To meet these reliability requirements, manufacturers of mills, drives, castings and other components have had to be innovative and creative in their design. Only by thorough review of past designs and practices and by model studies confirmed in field tests can the manufacturer have full confidence in the product. Because of the great interest in large mills, a short review of larger machines is presented. This discussion covers material feeding, bearings, the rotating element, drive trains and material discharge.

Jan 1, 1979

By Antoine Fournier, Karen St. Seymour

"Responding to market developments, interest in locating deposits of wollastonite has grown significantly. The many occurrences in the Grenville marbles of Quebec can be grouped into disseminated type and discordant vein-type deposits. Disseminated-type wollastonite occurrences have the disadvantages of lower grade, the need for more elaborate mineral separation, and failure to meet ""long grain"" technical specifications. Vein-type deposits have better grades and technical characteristics; exploration should be focussed on these and in the contact-metamorphic aureoles of fluid-rich intrusions. SOMMAIREEn réactions aux nouveaux de bouches, l'interet pour les gîtes de wollastonite a crû de façon marquée. Les nombreux indices sis dans la province de Grenville au Québec peuvent être regroupes en deux catégories soit: les indices dissémines et les indices en veines discordantes. Les indices dissémines ont le désavantage d'être moins enrichis, de requérir une séparation minéralogique plus complexe, et leur wollastonite ne possède pas le degré d'acicularité voulu. Les indices en veines sont plus enrichis en plus de rencontrer les critêres techniques; les efforts d'exploration devraient se porter vers ce type de gites et aussi, sur les auréoles métamorphiques de contact d’intrusions riches en fluides."

Jan 1, 1992

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By Luis R. Fonseca, C. Raimat, C. Wendeler, A. Sanz

"Rockfall barriers are widely known as proven efficiency element to protect infrastructure by catching the rock blocks in the falling direction and absorbing the energy generated by them.It’s common in the project design phase and during installation, fix rockfall barriers for catch a high percentage of the falling blocks and in many cases consider as valid the solution when the barrier can capture all of them. However, in many cases it’s possible to consider the use of these protections, simply to guarantee a secure shed for the traffic and intercept simply the blocks that theoretically hit the road surface.The results of the high-energy rockfall protection barriers type GBE which protect GC-200 road in Las Palmas de Gran Canaria are shown in this paper.The topographic data should be especially detailed observed and even more if you want to apply the technique of ""shadow zone"" with a flexible gallery system. It should be drawn from detailed topographic maps and drawings (photogrammetric restitution) to the scales 1/1000, 1/500, or 1/200; and it is important not to ignore the presence of vertical cuts, tracks, small slopes that modify the trajectories (trampoline effect, hard points that favor the rebounds) and which are not always presented in the drawings.The ""shadow zone"" is defined as the protected area, located at a lower elevation to the line created by the rockfall barrier to except of trajectories of rocks and free from the influence of the deflection of the system under the maximum energy level for which it was designed (MEL)."

Jan 1, 2015

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

"Beneficiation of low grade ores is the process of increasing the grade of a mineral through unit operations that remove and separate the waste (or gangue) material from the valuable mineral that can then be used for further processing or direct use. Important factors when deciding upon a beneficiation program are the feed grade, mass yield and the metal recovery. As lower grade ores are being processed beneficiation is a critical process. How predictive is laboratory test work for “as built” operating projects? Beneficiation includes all or some of the available unit operations to produce a beneficiation flow sheet i.e. associated unit operations including but not limited to optical sorting, radiometric sorting, crushing and screening, coarse cobbing, jigging, dense media separation (DMS), spirals, magnetic separation, flotation, thickening, filtering and drying. Reference to specific projects and the approach developed in formulating a beneficiation flow sheet and a comparison of difficult and simple beneficiation flow sheets are cited. INTRODUCTIONReserves of high-grade iron ores are reducing all over the world, at an alarming rate, over the years as a result of the rapid increase in demand for steel particularly from Japan and then China. The recovery of mineral value from the low-grade ores using present technology is more expensive than DSO ores due to high energy and capital costs. Beneficiation is defined as a variety of processes whereby extracted ore from mining is reduced to particles that can be separated into mineral and waste.Various physical properties of an ore can be exploited to separate a low grade fraction including variation in hardness, density, reflectance, conductivity and magnetism.""Beneficiation"" of iron ores includes concentration, generally by physical removal of unwanted gangue. Also considered beneficiation is the regulation of product size, or other steps such as agglomeration to improve its chemical or physical characteristics prior to smelting."

Jan 1, 2012

By J. A. Finch

The metallurgical performance of a flotation cell is strongly influenced by the features of the bubble population, characterized by the gas dispersion properties, a collective term including bubble size, superficial gas velocity and gas holdup. It is required that gas be well distributed throughout the cell. Gas distribution is estimated here by simultaneous measurement of gas velocity (Jg) at different distances from the center (radial Jg mapping). This communication describes a technique to perform radial Jg mapping together with fundamentals for the interpretation of the data.

Jan 1, 2009

By M. Mahdi Aboutalebi, Roderick I. L. Guthrie, Mihaiela Isac

"A preliminary computational fluid flow model has been developed to simulate the flow field of liquid steel in the mold region of billet mold casting. This study reports the effect of different Submerged Entry Nozzles (SEN) on the fluid flow in round and square billet, curved mold, casters. In this study, ANSYS Fluent 14.5 software was used to model the 3-D turbulent flow of liquid steel. The standard k-0 model was used to simulate turbulence in the mold region. Similarly, the species transport equations were discretized to simulate the dye injection test into the mold cavity. The behavior of flow in the mold region was validated against previous experimental work. Predicted results showed that different nozzle types plus the slight curvatures in the molds can significantly influence the flow patterns generated within the mold region, and thereby affect the finished quality of the billet products.INTRODUCTIONConventional Continuous Casting (C.C) processes are presently used to solidify more than 95% of the 1.5 billion tons of steel now produced in the world annually (World Steel in Figure, 2014). This overwhelming contribution of C.C processes for steel production is the prime motivation for this study, in order to understand and optimize the casting processes and thereby reduce internal defects and minimize energy consumption. The primary objective of all C.C processes is to maintain liquid metal purity during the casting process and to create a uniform flow within the caster so as to avoid internal and external defects. In this regard, studying fluid flows in the mold region of continuous caster has attracted many research groups, in both academia and industry, in recent years. The mold region is one of the most critical parts of the C.C. process, in which the transport phenomena associated with this region can significantly affect the quality of the final products. Thus, proper control of fluid flows within this region can be expected to greatly decrease both internal and surface defects such as Oscillation Marks (OM), inclusion entrapment, and Mold Powder Entrapment (MPE). In the casting process, the fluid flow in the mold region can be affected by a number of variables, such as; the flow control system (stopper rod or slide gate), nozzle geometry, SEN (Submerged Entry Nozzle) depth, casting speed, mold dimensions, gas injection, and the application of electromagnetic fields. One of the most influential and easily-changed fluid flows are the jets of steel issuing from the SEN. Nozzle geometries are variable, consisting of a number of exit ports, different port angles, and/or port sizes, the bottom shape of the nozzle, and the SEN immersion depth (Thomas, 2001). The SEN characteristics can markedly affect meniscus surface velocities, surface level profiles, and turbulence levels that can vary in terms of the frequency and the magnitude of their fluctuations."

Jan 1, 2016

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983