Search Documents

By S. Sillitoe

In mining, as in other business and engineering enterprises, efficient operation depends upon how well and how quickly the lines of communication can function. Mines have used the telephone on and between levels for many years, but in the hoisting shaft maintenance of physical wire connections for communication with the moving cage or skip has been found, for all practical purposes, impossible. A most natural solution was, therefore, the code-bell or buzzer signal system between fixed levels, and this has been standard practice throughout the mining world for many years. However, this system has serious limitations which make it impossible to signal a cage between levels in the shaft, and it requires crude, hazardous or costly methods for signalling during daily shaft inspection. Radio signalling overcomes these difficulties, because the communication medium is never broken and the cage-tender or shaft inspector can safely signal to, and receive signals from, the hoistman at any time from any position in the shaft, whether stationary or in motion. In addition to both audible and visual code signalling, two-way telephone communication and slack cable alarm are facilities made possible in recent commercially developed equipment.

Jan 1, 1949

By Akiyoshi Horiuchi, Manabu Kanno, Shigeki Sato, Taro Aichi

"AKITA ZINC Co., Ltd. (Iijima Zinc Refinery), jointly owned by DOWA METALS & MINING Co., Ltd.(DMM), has used the company’s own hematite process for iron control since the beginning of operations in 1971. The hematite process consists of reductive leaching with SO2 gas and iron removal in autoclaves by high temperature hydrolysis. This process enhances not only zinc recovery but also the recovery of gold, silver, copper, lead and rare metals, which is carried out at another DOWA metallurgical plant. All by-products produced in the hematite process are marketed and sold. This paper presents an overview of the hematite process and the recent process improvements made.INTRODUCTION DMM carries out mining and smelting activities for precious metals, PGMs, rare metals and base metals such as copper, lead and zinc. It owns KOSAKA SMELTING & REFINING, producing copper and lead, and the AKITA ZINC Co., Ltd. (AZC) in Akita Prefecture. DOWA is a specialized smelting company which has established a metallurgical complex for copper, lead and zinc, including a recycling business. AZC was established in 1971 at a production capacity of 72,000 t/y zinc; it is jointly owned by DMM and five other non-ferrous metal companies. AZC has increased its capacity continuously and now produces 210,000 t/y of zinc. Figure 1 shows the changes in zinc production and capacity at AZC."

Jan 1, 2016

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By Helen Morrison, Chris Staun, James Vaughan

"Mercury is introduced into the Bayer refining process as a trace element in bauxite. During the digestion stage, a portion of the mercury is extracted which partitions between the flash tank off-gas, vapour condensate and bauxite residue streams. A technology or treatment that stabilises mercury in the solid phase during digestion would prevent environmental management issues that may arise from the presence of mercury in condensate and non-condensable gases. This study examines the effect of process additives on the deportment of mercury under Bayer digestion conditions. Bauxite digestion experiments were conducted in batch autoclaves in the presence of additives. Process liquor was analysed for mercury content using a thermal desorption technique. Pyrite and copper hydroxide were evaluated for their suitability as additives.INTRODUCTIONMercury is an ancient metal characterised by electrochemical nobility, volatility, low solubility in water and a liquid state at room temperature (Holleman and Wiberg, 2001). The biogeochemical cycle of mercury is complex. Elemental mercury may enter the atmosphere due its volatility, where it can be transported long distances. After settling and adsorption to sediments, methylation is catalysed through microbial metabolism (Qureshi et al., 2009). Methylated mercury species are potent neurotoxins, and bioaccumulation of mercury is well documented, particularly in seafood (Kozin et al., 2013, Pan et al., 2014, Pollman, 2014). Environmental regulations for mercury emissions are becoming increasingly stringent (UNEP, 2015). Considerable research has already been performed and technologies developed for the remediation of mercury in wastewater and the trapping of mercury from industrial stack emissions. Wastewater technologies usually target ionised mercury using adsorbent, ion exchange and complexation mechanisms (Krishnan and Anirudhan, 2002, Li et al., 2015a, Chiarle et al., 2000), while stack emission technology is dominated by impregnated activated carbon adsorbents (Gao et al., 2013, Zheng et al., 2012). Related developments include piezoelectric amalgamating sensors for in line detection of gaseous elemental mercury in industrial stack emissions (Kabir et al., 2015, Sabri et al., 2011). There is a paucity of research regarding removal of mercury from the Bayer process."

Jan 1, 2016

Electric Vehicle Controllers Ltd. ?EVC started in 1981 ?Underground electric locomotive drive systems ?Developed tandem load sharing system and radio ELOS controls ?Locomotive autonomy systems ?Entered space technology development in 1999 with NORCAT to develop Mars drill for CSA ?Commercial distributor for drilling systems, lunar physical simulants, electric mobility systems and lunar mining technologies

May 1, 2009

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By G. Gabra

"A process of leaching niobium oxide from pyrochlore concentrate using hydrofluoric acid is described. Variables such as acid concentration, temperature, reaction time, solid/acid ratio, agitation speed and particle size are correlated to the recovery of niobium oxide.The relatively low activation energy (1,86 Kcal/mole) and the dependence of reaction rate on agitation suggest that the process is diffusion controlled. The optimum conditions for extracting niobium oxide from the leach solution, using either methyl isobutyl ketone or tributyl phosphate have been determined.IntroductionMost of the commercial production of niobium and tantalum has been derived from the treatment of columbite - tantalite minerals.In recent years (1960) , pyrochlore mineral has been found to be an alternate source of niobium . This mineral varies widely in composition and contains in addition to the main elements of calcium , sodium and niobium, some tantalum, fluorine, rare earth elements, titanium, alkali an d alkaline earth elements.It is well known that the province of Quebec possesses several pyrochlore niobium deposits totalling approximately 151 million ton s at an average 0.45% niobium oxide(1). One of the deposits, the St-Honor carbonatite, was brought into production by Niobec Inc. in 1976. Flotation o f this material produces a concentrate of about 60% Nb205(2).In view of an expanding niobium market in recent years and the presence of large niobium deposits in the province, a research and development program was initiated at the Centre de Recherches Miner ales to evaluate known processes for the separation of niobium and tantalum from each other as well as their purification . Some work has also been undertaken at the CRM to develop an improved extraction process. T his work will be the subject of further communication s."

Jan 1, 1985

"This paper describes an alternative method of vehicle control which uses a micro-processor to control the field current and armature voltage concurrently. The field tests carried out and the conclusions drawn from the basis of the paper.IntroductionIt is generally accepted that the main obstacle to a greater use of electric vehicles is the relatively poor range and performance when compared to alternatives such as diesel and petrol-engine vehicles. Much effort has been applied to the problem of increasing the energy storage density of batteries and considerable improvements are now being reported.Improvements in the efficient use of the stored energy, although unlikely to achieve the necessary increase in range and performance for a widespread acceptance of electric vehicles, can nevertheless make a useful contribution. Because the improvement in efficiency is achieved by a reduction in losses, it follows that the temperature rise in drive-train components is reduced. These advantages, coupled with the increasing cost of energy, make improvements in the efficient use of the stored energy desirable, if not absolutely necessary. To achieve this with the large and rapidly varying loads encountered during the operational use of a vehicle will require a more flexible system of control than that provided by the current limit. This paper describes an alternative method of control which uses a micro-processor to control the field current and armature voltage concurrently.The value of these parameters is selected to supply the power demand at the motor shaft, with the minimum losses in electrical transmission, thus increasing the efficiency with which the stored energy is used."

Jan 1, 1982

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

Weekly Capacity ? Current Schedule Rate (198.5 tonnes / hour) X Skip Time (112.7 hours) X Effectiveness (85%) = Weekly Capacity (19,015 tonnes) Capacity Conclusions - Existing hoists optimized are best option for Fraser Morgan (>20M + schedule for other). - Peak will have to be managed. - Critical to have equipment & infrastructure in best possible condition to ensure reliability.

Feb 1, 2008

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By Gary S. Anderson

Rajant Corporation is the global leader in mining communications systems implemented a vision to develop a wireless network that is rapidly deployed, self-powered and managed, for portable or fixed configurations ? Mobile, Portable, Self-Powered, Secure and High Bandwidth. The network configures itself allowing for very rapid deployment without the time delay and personnel typically required for set-up and configuration. Rajant?s proprietary technology ?InstaMesh®? is incorporated in a device called a BreadCrumb®. Rajant has filed several patent applications on its proprietary technology and has received trademark protection on its brand names. The BreadCrumb® uses technology which allows mining, military and first responders to easily establish internet connections at remote sites or situations where existing internet communications has been disrupted. The BreadCrumb® products are standards-based Wi-Fi 802.11 a/b/g compliant, ruggedized, lightweight, portable; self-meshing and the system can be established by just turning on several of the BreadCrumb® units. The Rajant Network has evolved in the ?One Network? philosophy and has been deployed by both the military and homeland defense organizations. With multiple radios, transmitting on multiple frequencies as the same time, bandwidth is doubled, the speed of the network is enhanced, management is simplified, and manageability is made easier. Rajant has partnered with world class integrators and partners, including ten CAT dealers, a world-wide mining technology company, a mining and construction software company and leading technology innovators in mining automation and operations. Recently, Rajant provided a significant network to Rio Tinto?s Iron Ore of Canada Mine in Labrador City, Newfoundland, Canada, Kennecott Utah Copper Mine, and is currently the wireless standard at Peabody Energy and several mines in Australia. These networks range from 20-250 BreadCrumbs®. The result is a meshed mobile broadband network capable of operating in a vast open pit active mining space. Simultaneous applications currently running on these BreadCrumb® networks in the mining sector consist of Caterpillar?s VIMS?s, CAESultra grade control and Aquila Drill Management Systems, Carlson Grade Control systems, Jigsaw Technologies and Modular Mining fleet management system, Ground Probe Radar, an Automatic Train Operation and various video and VoIP applications. All vendor applications have been turned off and all applications are running on Rajant?s ?One Network?.

May 1, 2010

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By Sarah R. Hindle

Carbon capture and storage has jumped to the forefront of climate change mitigation efforts for its capacity to sequester large amounts of carbon. Mineral carbonation is one prominent option, mimicking and accelerating the natural weathering process of certain silicate minerals. This has the ability to produce stable carbonate minerals that can store carbon on geologic time scales with little to no risk of leakage. Commercialization of this process is ideally suited for integration into the proposed mining operations at the Turnagain Nickel site in Northern BC. This is due to the abundant supply of suitable ultramafic feedstock material, as well as the economic benefit of sharing costs while reducing net emissions and bringing value to otherwise valueless and costly waste rock. While studies have shown this process to be technologically viable on a laboratory scale, assessing the economic and financial viability of such a process on an industrial scale is necessary. An evaluation of the financial feasibility of integrating mineral carbonation into the mining cycle at Turnagain under a proposed cap-and-trade system is presented.

May 1, 2010

By W. F. Harkness, D. Hodgkinson

"A non-destructive testing program was established at Crows Nest Resources (C.N.R.), Line Creek mining operation following an in-service fatigue failure of a front wheel spindle on a large haulage truck.This failure identified a definite need for improvements in the ultrasonic techniques used during the mandatory spindle integrity examinations. Initial investigations using common mining industry ultrasonic examination techniques showed that the smallest detectable cracks were 75 mm in length for the spindle types in service at the C.N.R. site. The Initial findings indicated that inadequate inspection technique design was the cause of the poor performance. To improve inspection reliability it was identified that improved ultrasonic techniques were required. Results using designed ultrasonic techniques were encouraging, with the detection of simulated and natural cracks 12 mm long achieved. The cost benefits associated with the extended spindle life, following the removal of these small fatigue cracks, far exceeded those of the expertise and effort necessary to implement and conduct the N.D.T. program.Introduction During 50 years of evolution, non-destructive testing (N.D. T.) has progressed from a laboratory curiosity to a well accepted and invaluable tool used in the assessment of material integrity. Unlike destructive testing, N.D.T. does not deform or render the material useless. Non-destructive tests may involve many applications, from the determination of a corrosion prevention coating thickness to the examination of a raw material for internal and external deformities.Within the mining sector, highly-stressed components will normally have been subjected to some form of non-destructive test during their manufacturing cycle. These tests are used to ensure the component does not contain material flaws whichmay be detrimental to its service performance.While the component may have assured quality when produced, deterioration by fatigue may occur during an aggressive service life. Large dynamically-loaded components such as haulage truck front wheel spindles are , in particular, prone to this service related problem."

Jan 1, 1987

By Hamid-Reza Manouchehri

Coarse particles flotation is controlled by detachment (particle hydrophobicity and flotation cell turbulence) For composite particles (the bubble may attach to good hydrophobic region, but the expansion of the three phase line of contact is limited. Hence, the equilibrium contact angle, characteristic of the hydrophobic region, may never be attained, and the force of attachment is decreased relative to that possible for homogenous hydrophobic surfaces.

May 1, 2013

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019