Search Documents

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995

By N. Hosking, M. Nichols

Aluminum alloys are increasingly used for automotive body construction but are susceptible to filiform corrosion or paint blistering in service. Filiform corrosion resistance of two 6000-series aluminum alloys was investigated in this work. Test panels were produced with full automotive coating layers and scribed parallel and perpendicular to the rolling direction. The corrosion exposure comprised an inoculation step with acidified salt solution followed by a 6-week exposure period at 95% relative humidity and either 25°C or 70°C. Greatest corrosion activity was measured on the alloy with higher copper content, AA6111. Higher temperature exposure led to greatly enhanced corrosion activity for AA6111 compared to the lower temperature exposure. The 70°C exposure also led to greater mean corrosion-affected area measurements for the low copper aluminum alloy, AA6022, but the effect was not as stark as that observed for AA6111. Rolling direction affected the propagation direction, and possibly mechanism, of the corrosion effects. Cross-sectional analysis revealed dense corrosion products within the filament, comprising mostly aluminum and oxygen but with traces of chloride and sulphate. Development of varying filament and blister types on a single test panel and the progression of corrosion underneath a filament into the substrate indicate that several corrosion mechanisms can develop on the test panel, testament to the complexity of the corroding surface developed on an aluminum automotive body panel.

Jan 1, 2015

By R. P. Kofluk

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Significant economic implications are associated with the refining of precipitated sulphides containing elevated iron contents. The Moa Nickel S.A. operations encompass laterite mining, high pressure acid leaching (H PAL), and ultimately, precipitation of a mixed sulphide product. These processes are reviewed as they pertain to the control of iron and the formation of a mixed sulphide containing nominally 55% Ni, 5% Co and 1% Fe. The contributors to the iron content of the mixed sulphide product are reviewed; the major contributors are the HPAL operation and sulphide precipitation. The precipitation of iron during sulphide precipitation is influenced by the solution acidity, the iron and copper concentrations in the feed solution, and the presence of laterite leach solids. The significance of the copper concentration of the sulphide precipitation solutions is manifested by both physical and chemical modifications of the sulphide precipitates, presumably through the formation of fine copper sulfide seed particles.

Jan 1, 2006

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By G. J. Arseneau

ABSTRACT Mineral resource statements are reported as tonnage (volume × density) and grades. Effort is expended to accurately estimate the volume and grade, but accurately determining bulk density is often overlooked. Oversimplification of density modelling can result in potentially serious errors in tonnage estimates and over- or underestimation of metal content. A reliable bulk density model requires an adequate database and a good understanding of density variability, along with grade and geology. In this paper, the author summarizes density measuring techniques, draws on examples of simple and complex grade-variable density domains, and discusses improved approaches for minimizing density estimation errors.

Jan 1, 2014

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015

By R. H. Fett

T HE APPROACH to maintenance must always be ?completely positive: there must be no question of putting off difficult problems until it is more convenient to tackle them. By this it is meant that a piece of machinery or equipment which, by experience, is known to be due for a check should not, merely because it appears to be operating satisfactorily, be left until it reaches a critical .condition and breaks down. The mentality of the Maintenance Manager must be completely orderly and methodical and he should, in fact, possess a ledger-book mind, having a debit and credit outlook. The debit side would be that applying to time out of service, cost in wages, material, personnel involved, etc., and the credit side that relating to continuous operational time of the locomotive and therefore to the ultimate benefit of the mine and the personnel who work there. The Maintenance Manager is not concerned with design problems, and although he and the personnel under his jurisdiction are not engaged in productive work, he and his staff do, nevertheless, add greatly to or detract from the overall efficiency of the organization. Provided the machinery placed in his care is good to start with, he must take the best steps he possibly can to keep it running. However, he may, on occasion, be forced to improvise and this is where the ingenuity of a clever man rises to the occasion.

Jan 1, 1956

By Blaycock. S. C.

WE should indeed feel proud and satisfied with the accomplishments of our great mining and metallurgical. industries during the past quarter of a century, for they have vastly exceeded those of any previous period of like duration. 1 feel that Canadians, and particularly those in the mining industry, should know more concerning the important role our industry will be called upon to play in the present war. Our Empire metals will be an outstanding factor in this conflict. Every man connected with the industry, from the lowest paid labourer to the highest official, can feel proud that his every effort results in more and more production of those metals which will help to give the Empire supremacy. He can feel assured that, by sticking to his job and by putting his whole heart into his work, he is making a contribution towards winning the terrible struggle in which our Empire and our gallant French allies are engaged. These two great peoples will have ro bear the brunt of the task of ridding the world of the menace of those who would set up force. and might in the place of right and justice in the settlement of international affairs. As the present European crisis developed, it became evident that they, alone, would have to accept the challenge and fight the enemies of Democracy to ensure the survival of the small nations of Europe and, indeed, of the great democratic powers themselves. The acquisitive eye of the German leaders had looked far ahead and they had realized that the eastern European states, already reeming with population, were no solution to Germany's space problem; but they thought that these states could be gobbled up one by one, each in turn strengthening Germany's might until it could successfully challenge France and England. No glimmer of doubt dimmed their vision. The two great democracies once subdued, they could proceed to seize Canada and the United States. This clone, they would have an abundance of room to expand, as well as those resources-grain, timber, cotton, nickel, iron, lead, zinc, copper, gold, silver, sulphur, oil-which German statesmen have always coveted. Von Ribbentrop, von Alvensleben, Bernstorff, and many others have made exhaustive studies of our resources. German rulers had been told that the French would not fight and that the British could not. They knew of the rust on the British war machine. There was no cloud in the sky; their fond dream was at last robe fulfilled.

Jan 1, 1940

By A. Banerjee, J. P. Weiler, J. Jekl, J. T. Wood, R. Berkmortel

"The work presented here is part of an ongoing project designed to develop predictive capabilities of the local mechanical properties, and thus, structural behaviour of a thin-walled high-pressure die-cast AM60B magnesium alloy component. This work focuses on developing correlations between process parameters and local microstructure. Numerical simulations of the die filling and solidification behaviour of the AM60B component were used to estimate local process parameters such as solidification rate, temperature gradient, filling velocity, etc. These estimated parameters were used to establish semiempirical correlations with measured VALUES (of the local microstructure measured in regions throughout the component of different solidification conditions. INTRODUCTIONHigh-pressure die-cast magnesium alloys are experiencing increasing use in structural automotive components. A strength-to-weight ratio comparable to steels and its ease of castability allow for these alloys to be utilized in such capacities as instrument panel beams, seat and door frames, and engine cradles, among others (Gjestland and Westengen, 2007). However, the current use of these alloys is limited due to variations in local mechanical properties. These local property variations restrict part designers to assume lower than actual properties, resulting in larger sections, thus diminishing the light-weighting advantages of magnesium alloys. If these local property variations could be predicted, part designers would be able to optimize die-cast magnesium alloy components and fully take advantage of the light-weighting capacity of these materials.The work presented here is part of an ongoing project aimed at developing predictive capabilities of the local mechanical properties, and bulk mechanical performance, from variations in local microstructure, and ultimately from local process parameters in die-cast magnesium alloys. This project, unique in its nature, is based upon the results determined from fifty sequentially cast AM60B magnesium alloy instrument panel beams provided by Meridian Lightweight Technologies (shown in Figure 1)."

Jan 1, 2012

By J. C. Ingles

"A survey of possible methods for controlling cyanide concentration indicated that the simplest method would involve the use of a potentiometric technique. Such a method was suggested by a paper from the laboratory of Mines Safety Appliances, which described a method for determining hydrogen cyanide in air. In this application, the cyanide was absorbed in caustic and a silver electrode immersed in the caustic solution provided a measure of the cyanide concentration. However, our attempts to use the silver electrode in this simple manner to measure the cyanide concentration of solutions were not very successful. A study of the mechanism by which a silver electrode responds to cyanide concentration made it evident why this simple procedure is not satisfactory.Basically, the silver electrode provides an indication of the free silver ion concentration of a solution, and generally speaking, ignores the other ions' present. It can be used to measure an anion if this anion complexes silver. This technique has been used in complexing studies to determine the activities of such anions as acetate, citrate, oxalate and chloride. To do this, the electrode has to be placed in a solution which initially contains a known concentration of free silver ions. Addition of the complexing anion causes a drop in the free silver ion concentration and hence a change in the potential of the silver electrode. The change in potential can be expressed in terms of the concentration of the complexing anion, and used to indicate its concentration in the solution being analysed. The determination of chloride-ion by a silver-silver chloride electrode is an example of an application of this technique. The solubility of the silver chloride with which the electrode is coated provides the initial free silver-ion concentration. Depression of this free silver-ion concentration by the presence of the excess chloride ion of the sample solution results in a change in the potential of the electrode which is proportional to the chloride-ion concentration."

Jan 1, 1965

By C. Pichler, S. Luidold, C. Wagner, C. Sagadin, D. Kreuzer

Engineers and scientists have been combating the attack upon refractory materials of molten metals/matte and slags for hundreds of years. The details in many cases are still questionable or at least debatable. The corrosion is a major concern for furnace operators as refractory wear or failures inevitably results in reduced production efficiency and furnace reliability. Also the cost to industry is considerable and only a thorough understanding of all the complexities of the process will help to minimize that cost. One of the critical questions to overcome is the correct selection of refractories for the individual process steps to provide long and predictable refractory life together with high furnace availability. To understand the nature of the reactions involved in refractory corrosion, it is crucial to determine the complex thermo- chemical equilibria of the reactions occurring between the refractory materials and the process phases. A simulation model coupled with commercial software like FactSageTM is demonstrated aiming to understand the corrosion mechanisms between refractories and the molten process phases and draw implications for improving the performance of refractories and refractory lifetime. INTRODUCTION The extraction or recycling of valuable materials, e.g. metals, can be done by two main routes, pyro- and/or hydrometallurgical processing, depending on the chemical behavior of the used ore, scrap or pre-treated concentrate. Sometimes it is also necessary to use both process routes for the extraction or the recycling of valuable materials. In the case of a pyrometallurgical treatment, the usage of refractory materials is inevitable. This is mainly caused by high temperatures, prevailing during processing. The interaction between refractory material and slag, metal or matte leads to different reactions and interactions. As a main result corrosion of the furnace lining (refractory material) takes place. Hence, recurring furnace shutdowns occur for renewing the refractories. This leads to reduced production efficiency. Such refractory lifetimes are between some hours and decades, depending on the processes.

Jan 1, 2019

By H. Soltanzadeh

This paper summarizes semi-analytical and closed-form solutions that can be used to assess the poroelastic stress changes induced within a porous formation (reservoir) during a pore pressure change. Further, solutions are presented for the stress discontinuities at the interfaces between reservoirs and the rocks that surround them. When used in combination with rock failure criteria, these solutions enable relatively simple analyses of the potential for induced fracturing or fault reactivation within a reservoir or the rock immediately adjacent to it. The latter, in particular, is useful for assessing if the hydraulic integrity of the surrounding rock (i.e., the bounding seal) will be affected by a pore pressure change. The use of the approach presented in this paper is illustrated with an analysis of a pinnacle reef with dimensions and properties representative of reefs in the Zama oil field, northwestern Alberta, Canada. Scenarios of pore pressure decrease (during historical production operations) and pore pressure increase (during several years of acid gas injection operations) are analyzed, for three different idealizations of reservoir properties and geometry (two plane strain and one axisymmetric). These results suggest that that the potential for induced fracturing is not significant at any point within the reservoir or the surrounding rock for both the production and injection scenarios that were simulated. Similarly, fault reactivation was not predicted for the reservoir or any of the points that were analyzed in the surrounding rock. However, fault orientations having the greatest potential for reactivating during historical production operations were identified; thus, illustrating a means of using geomechanical models to focus geological characterization efforts on the features that are most critical to acid gas containment.

May 1, 2009

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By Golaleh Riahi

An original method is used to obtain stable nanoparticles of gold-based mono- and bimetallic systems supported on an acidic zeolite. This approach has been applied to PtHY (1wt% Pt) and to bimetallic Pt-AuHY containing 1% of platinum to which is added the amount of gold required to give Au/Pt molar ratios of 20,40,60 and 80%. Metal clusters of Au or Pt-AuHY are formed inside the supercages of the zeolite framework by the thermal reduction of cations by the ligands (en = H2N-CH2-CH2-NH2) under inert gas flow at a temperature depending on the metal. The use of acidic zeolites favours the dispersion of the metal and the thermal stability of the particles. This stability is explained by chemical anchoring of metal clusters by the Brønsted sites of the support. Several techniques have proved that for a molar ratio of 20% metal particles of Pt-AuHY are bimetallic. The segregation of Pt and Au starts for molar ratio =?40%. The catalysts tested on the methylcyclopentane hydroconversion reaction reveal that the addition of gold to platinum leads to an increase in the activity and an improvement in the selectivity for isomerization of the skeleton (cyclohexane and benzene) to the detriment of hydrogenolysis. Similar results were obtained for the dodecane isomerisation to isododecane. These catalysts were also tested in CO, propene and propane oxidation. The activity of fresh catalysts is rather low. It increases after their pretreatment in oxygen or hydrogen atmosphere. In propene oxidation in the reaction mixture O2 ? H2, beside total oxidation of propene to CO2, also propene hydrogenation was observed, particularly at low temperatures. The presence of Au enhances the hydrogenation properties: high selectivities (> 90%) to propane and high propane yields on PtAu HY are observed up to ~150oC, whereas for Pt HY catalyst the selectivity and yield to C3H8 decreases rapidly with the temperature beginning from ~100oC.

Oct 1, 2003

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By Frank Mucciardi, Louca Gourtsoyannis

"Low and inconsistent recoveries of aluminum in the production of aluminum-killed steels triggered an extensive research program on the aluminum dissolution kinetics at McGill University. This research program led to the understanding of the melting kinetics and the hydrodynamics of making additions to liquid steel. It showed the necessity of gradually releasing liquid aluminum at the bottom of the ladle to increase aluminum recoveries.This knowledge was verified in practice at Sidbec-Dosco, where a prototype aluminum wire injector was developed and installed for the first time in Canada. The industrial application showed the validity of the theoretical and experimental results and provided further data for the mathematical modelling of the process.The development of the theoretical understanding, the industrial results, and the interaction between university and industry are presented.IntroductionAluminum is an extremely effective deoxidizer of molten steel; nevertheless, an efficient method of adding it to steel has eluded steelmakers for many years. It is well known that the recovery of aluminum used in the production of aluminum killed steel is both low and eratic, especially when the aluminum is added in the form of bars or lumps from chutes into filling ladles, a practice still common in many of today's steelmaking operations.As the density of aluminum is only about 40010 that of molten steel, it is conceivable that loose bars of aluminum simply ""thrown"" into a filling ladle will resurface before any appreciable dissolution of the aluminum has occurred, particularly if the depth of penetration of the additions is small. Before one can conclude that this is indeed the case, it is necessary to know the melting kinetics of an aluminum addition. Back in 1972, this information was not available; hence an extensive research program which focused on melting kinetics was initiated at McGill University."

Jan 1, 1982

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013