Search Documents

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

This paper aims to increase our understanding about existing capacity-building approaches and their implications for obtaining a social license to operate in the mining industry. The notion of ?capacity building? is gaining increasing currency in the mining sector in developing countries due to a rapid rise in the globalisation of mining operations. Capacity-building is conceived here as a process that lasts after the mine-cycle, intended to provide local mining communities with tangible skills and knowledge to gain meaningful employment in mining or other industries relevant for the local economy. Building community capacity to understand and effectively respond to these transformations is vital for obtaining a social license to operate, as it promotes sustainable and locally relevant development. Accountability mechanisms such as global norms and international standards increasingly highlight the need to build capacity among stakeholders, particularly among local communities adjacent to mining operations. International frameworks and mining companies have embraced the notion of capacity-building as a driver to assist corporate social and operational performance. However, this narrow understanding of capacity-building through the prism of corporate social responsibility and ?best practice? is preventing the industry from meaningfully impacting communities and maintaining a social license to operate. This latter notion is being widely embedded across multiple industry sectors, as a social and economic reward from mining companies to compensate communities for natural resource extraction and gain social acceptance. Although both concepts are widely recognised in the minerals industry, insufficient attention has been paid to the implications of applying a top-down (mining-orientated) or a bottom-up (community-orientated) capacity-building approach for obtaining a social license to operate, or indeed how these two concepts are linked and applied in practice. At times, communities lack the necessary capacities in the form of education and skills to deal with mining-led livelihood transformations. This is preventing both mining companies and communities from forging sustainable livelihoods and responding to mining-led livelihood transformations, a situation that is creating discontent among communities and reducing the possibility of obtaining and renewing a social license to operate for the industry. Based on a review of current scholarly debates, accountability mechanisms in the mining industry and fieldwork findings in Colombia, this paper will contribute to an understanding of the implications of existing capacity-building approaches that support a social license to operate.

Aug 1, 2013

By G. O. Allard, A. Gobeil

The Chibougamau area is the eastern segment of the MatagamiChibougamau greenstone belt. The Archean rocks of the area consist of two mafic-to-felsic volcanic cycles ( Roy Group) overlain by a sedimentary-volcanic sequence (Opemisca Group). The Roy Group volcanics are intruded by many coeval and comagmatic differentiated gab bro sills. The Supracrustal rocks of the Roy Group and Opemisca Group have been folded about north-south axes, refolded isoclinally about east-trending axes and metamorphosed to the greenschist facies. The same lithologies have been identified east of the Grenville Front at amphibolite grade. The first volcanic cycle consists of 3000 metres of porphyritic pillowed basalts and comagmatic gabbro sills (0batogamau Formation) overlain by a thin sequence of felsic pyroclastics, porphyritic dacites, and iron formation (Waconichi Formation). The Dore Lake Complex is a sill-like layered complex intruded in the upper part of the Waconichi Formation. The second cycle consists of 3600 metres of pillowed basalts and gabbro sills (Gilman Formation) overlain by a volcanosedimentary assemblage less than 1000 metres thick (Blondeau Formation). The Cummings Complex consists of the Roberge sill (dunite and peridotite) at the base, the Ventures sill (gabbro) and the Bourbeau sill (leucogabbro and quartz ferrodiorite) at the top. It is emplaced within the Blondeau Formation. The Opemisca Group sediments and minor porphyritic K-rich andesites (Stella, Hauy, and Chebistuan Formations) form narrow belts preserved in the synclines of the area. The Proterozoic rocks of the Chibougamau area consist of conglomerates, arkoses, and argillites with dropstones of the Chibougamau Formation. North of Chibougamau, the Mistassini Basin forms an elongate northeast-trending basin filled with sediments of the Mistassini Group. Conglomerates, sandstones, argillites, dolomites, stromatolitic dolomites, and iron formation are the principal sediments within the basin.

Jan 1, 1984

By K. J. R. Ford, Botz. M. M.

Porphyry copper ores are frequently a source of low-grade gold ore, but gold in these ores is often associated with significant levels of cyanide-soluble copper. Cyanide leaching of such ores increases flowsheet complexity and operating costs, and requires thorough planning to satisfy environmental requirements for tailings disposal and mine closure. This paper presents a review of the chemistry of cyanide leaching of gold-copper porphyry ores, carbon adsorption phenomena and means of removing base metals from leach solution. The primary economic drivers behind the processing of such complex ores are also analyzed.

Jan 1, 2011

By Michael L. Wayman

Archaeological and ethnographic work during the last century has shown clearly that metals have played a small but important role in prehistoric Arctic cultures. For at least the past several millenia both iron and copper have been used in the North, primarily for blades, projectile points, knives, awls, engraving tools, fishhooks, scrapers and axes. In addition they were used for joining purposes as staples and rivets. It is of great interest to enquire into the origins of these metals. In this connection one begins with the observation that to date there has been no clear evidence for the smelting or melting of metals in the Arctic prior to the arrival of Europeans. This can be explained partly by the absence of traditional pyrotechnologies such as the high-temperature firing of ceramics and the heat treatment of bone and wood. Another factor which surely inhibited the development of smelting/ melting operations is the relative absence of wood in the region. The production of charcoal for smelting requires large quantities of wood, to the extent that the desertification of a number of areas in the Old World is believed by some to have been at least partly caused by charcoal production. In the North this was obviously not possible. Thus the Arctic peoples were restricted to using native (naturally occurring) metals and metals obtained by various direct and indirect forms of contact with areas of the world where smelting was practiced. Both of these sources were important in the case of iron; we know that meteoritic iron, telluric (native) iron and smelted wrought iron were all used in the Arctic. These three types of iron will be considered in tum.

Jan 1, 1999

By R. Pelton, Z. Dai, S. Yang

ABSTRACT Hydrophobic polystyrene nanoparticles were evaluated as potential flotation collectors for pentlandite. The flotation of hydrophilic glass beads demonstrated the nanoparticles’ ability to induce flotation. Deposition of nanoparticles on glass surfaces increased the contact angle and enhanced adhesion of the beads to air bubbles. High flotation recoveries were achieved when 5–10% of the bead surfaces were covered with nanoparticles. Surface functionalization—the addition of vinylimidazole to polystyrene nanoparticle surfaces—caused the nanoparticles to selectively deposit onto pentlandite surfaces in the presence of Mg-Si slimes. Ongoing work includes attempts to identify specific applications where nanoparticle collectors might be cost effective. _ KEYWORDS Flotation, Nanoparticle collector, Coverage

Jan 1, 2014

By C. Derek Martin

"Predicting the ground response for tunnels in weak shales remains challenging. Predicting the ground response is challenged by difficulties in characterising the material, and our ability to predict deformations that are driven by coupled hydromechanical processes, when this material yields. The techniques that are used for characterizing weak shales are reviewed, and three case histories are examined that demonstrate the behaviour of these weak rocks during tunnelling. A general framework is provided for assessing the squeezing potential for weak shales.1 INTRODUCTIONGeologically, shale is an argillaceous fine-grained sedimentary rock that forms from the compaction of silt and clay-size mineral particles commonly referred to as ""mud"". Because of this grain size, the material is generically classed as Mudstone (Figure 1). Shale is distinguished from other mudstones because it is made up of many thin layers (laminated) and readily splits into thin pieces along the laminations (fissile). While the geological classification of shale appears straightforward, the classification for engineering purposes is often confusing. Underwood (l967) provided the first description of shale that made the distinction between “soil-like” compaction shales and “rock-like ""cemented"" shales. He coined the term ‘clay shale’ to capture the characteristics of hard clay yet recognizing its origin as a shale. In this paper weak shale is synonymous with clay shale and have strengths that typically range from R1 to R2 (1 to 25 MPa). Characterising these materials draws on methods from both soil and rock mechanics."

Jan 1, 2015

By W. D. Sinclair

"Between 1934 and 1956, nearly 31 million grams of gold were produced in the Matachewan area from deposits on properties belonging to Young-Davidson Mines Limited and Matachewan Consolidated Mines Limited. In 1979, production from these properties was renewed by Pamour Porcupine Mines Limited.Most of the gold produced has come from relatively lowgrade deposits (3.4 gl t or less) that occur in an east-trending belt of dykes and irregular bodies of trachytic syenite. Although small by comparison, these deposits have some of the characteristics of porphyry copper-molybdenum deposits. The mineralized syenite contains up to 5 per cent disseminated pyrite and is highly fractured and cut by quartz and quartzcarbonate veinlets. Gold occurs as native gold along fractures, in quartz veinlets and as minute inclusions in pyrite. Minor chalcopyrite and trace amounts of scheelite, molybdenite and galena are also present. Mineralization was accompanied by potassic alteration, consisting mainly of potassium feldspar.Some gold was also produced from small, but higher-grade, deposits in volcanic rocks. These deposits occur near the syenite-hosted deposits and consist of quartz veins and stringers mineralized .with pyrite and gold. Minor gold is present in some low-grade, porphyry-type copper-molybdenum occurrences and, locally, in large, isolated quartz veins.Lead isotope analyses suggest that the gold deposits were formed at about 2700 Ma and were locally remobilized at approximately 2400 Ma, following the Kenoran orogeny. The deposits appear to be genetically related to felsic magmas emplaced in an epizonal environment and deposited from hydrothermal solutions relatively concentrated in S and K20."

Jan 1, 1982

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d 'uranium de Cigar Lake, dans la région de l'Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l 'Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d'ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l'échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l'intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d'altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d'Athabasca, et se compose essentiellement d'uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l'intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l'Athabasca; il est caractérise en particulier par l'intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s 'élevaient a 110 000 tonnes d'uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l'intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By T. Y. Chong, J. A. Folinsbee, M. Fullam

PJV Dome Mine has used some form of gravity concentration since start of milling operation in 1909 to recover free milling gold. Amalgamation and conventional jigs were first used and were replaced with the Knelson Concentrators in 1993. The Knelson concentrates produced were upgraded on a conventional shaking table prior to smelting and refining into gold bullion. In May 2002, a comprehensive review of the latest gravity recovery technology led to a piloting campaign aimed at further improving gravity recovery. The Knelson concentrates, subjected to intensive cyanide leaching in an Acacia pilot plant, were found to be amenable to intensive cyanide leaching with over 98% of the gold being dissolved within 24 hours. An Acacia Intensive Leach Reactor was successfully installed and commissioned in December 2002, to replace the shaking table. his paper describes pilot scale testing, installation, commissioning and optimization of the Acacia Intensive Leach Reactor. Also, the economic impacts on down stream processes are highlighted.

Jan 1, 2005

By E. LaRocque

"Long term contracts requiring delivery of 6,000,000 pounds of U308 per year to its customers have made it necessary for Denison Mines to expand its milling capacity from 7,100 tons per day to 15,000 tons per day.Previous papers (1) and (2) described the old leaching and product recovery practice. The flowsheet briefly includes a crushing and grinding circuit, sulphuric acid leaching in a Pachuca plant, liquid-solid separation with wash thickeners and two-stage drum filtration, concentration and purification by moving bed ion exchange followed by two-stage precipitation to produce an ammonia yellowcake.No. 1 Shaft ore, about 4,000 tons per day, will be processed through the truck dump into the old crushing and grinding plant and through the old leaching plant. Ore from Stanrock (No. 3 shaft) will be hauled by truck and also processed through the truck dump as No. 1 shaft ore. Beginning in 1982, ore production from Stanrock will gradually increase until 1985 when some 3,000 tons per day will be milled from the source.A new 8,000 ton per day circuit was designed and constructed to increase the milling capacity to 15,000 tons per day. The new circuit is separate from the old one except that it coins together for the precipitation and tailings neutralization sections of the plant. The feed to the new plant will be from No. 2 shaft.The flowsheet is much the same as the old plant with the exception of the grinding circuit and the ion exchange plant. A semi-autogenous grinding (SAG) plant, unique in the Elliot Lake area, has been installed rather than the conventional crushing and grinding plant; the ion exchange plant is the stationery bed type.This paper describes the major equipment installed for the expanded grinding and hydrometallurgical plant."

Jan 1, 1982

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By F. Habashi

"The rare earths industry started in Austria in 1887 by Carl Auer von Welsbach (1858-1929) Professor of Chemistry at the University of Vienna. The process was based on monazite sand transported from Brazil as shipping ballast free of charge. This made possible producing thorium, cerium, and other rare earths at a low cost, thus permitting the growth of the industry. However, once the Brazilian authorities realized the strategic importance of the sand, shipping was stopped. Brazil then started its own processing of the sand in 1949. The background for Auer’s work, the role of Robert Bunsen in Heidelberg, and the invention of the spectroscope will be presented. INTRODUCTIONHeidelberg on the Neckar (Figure 1) was the meeting place for chemistry students from all over Europe in the nineteenth century. Her university founded in 1386 had already a famous professor of chemistry and medecine in the Faculty of Medicine by the name Leopold Gmelin whose three - volume Handbuch der theoretischen Chemie appeared in 1817-1819, that became later a multi-volume monumental work. As successor to Gmelin came Robert Bunsen (Figure 2) in 1852 who made this university town the Mecca of chemistry students. One of his students, the English Henry Roscoe (1833-1915) who became later a distinguished professor in Manchester, described him as follows: ""As an investigator he was great, as a teacher he was greater, as a man and a friend he was greatest""."

Jan 1, 2012

By M. C. Harris

The past twenty to thirty years have seen unprecedented research activity aimed at understanding the performance of flotation froths. In 1990, Finch and Dobby coined the term froth recovery factor, Rr, to represent the efficiency of the froth in delivering particles from the pulp-froth interface to the concentrate. Originally defined for flotation columns, Rr has also been found useful in modeling mechanical flotation cells, and a number of techniques, based on quite different approaches, have been developed for measuring the froth recovery in industrial flotation cells. None of these techniques is universally successful. This paper reviews the concept of the froth recovery factor, and the basis of each of the techniques that have been proposed to measure Rr, and examines the reasons for this parameter being so difficult to pin down. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By N. R. Paterson, D. G. MacKay

"The geology of the Mattagami mining camp, while of particular economic significance, is unfortunately obscured by a very thick mantle of overburden. For this reason geo-physical methods have been relied upon heavily in exploring the area. Geophysical data over five important sulphide discoveries show how targets are selected for drilling and how effective geophysics has been in assisting subsequent development programs."

Jan 1, 1960

By E. V. Konopleva, H. J. McQueen, V. M. Khlestov

In addition to increasing grain boundary area during hot working of austenite, the dislocation substructures create potential sites for nucleation of ferrite both at original grain boundaries and at transition boundaries between deformation bands. This development gives rise to a marked increase in the rates of nucleation, of growth and of transformation to ferrite. The combined net effect is product grain refinement that requires less stringent cooling between finish rolling and coiling; hence determination of the above rates would advance process optimization. The important control parameters are the preheat temperature (degree of homogenization), finishing temperature, strain (accumulation near finishing) and the extent of recrystallization after finishing. These effects vary greatly with steel composition; nevertheless, some general rules have been formulated. Moreover, there is also potential for deformation of the refined ferrite. There are other thermo-mechanical processes such as warm forming of metastable alloy austenite to provide a dense substructure that is carried into the martensite on quenching. In other processes, the austenite may be deformed during cooling through the transformation to develop a dense substructure in the ferrite that is stabilized by fine carbides.

Jan 1, 2004

By H. Ito, T. Takasu

Effects of a mechnochemical treatment to oxide Ni ores have been investigated to enhance the extractive ratio of Ni from them in acid leaching process. High intensity grinding by a planetary boll mill showed strong effect to enhance the extractive ratio of Ni, for example , 10% of extractive ratio of Ni in sulfuric acid leaching(0.05mo1/1,at room temperature) increased to more than 90% with 60min. of planetary boll milling. Effects of additives(sulfur and some oxidants) on the mechnochemical treatment have also studied. Sulfur showed almost no effect to enhance the total Ni extractive ratio but increases the selectivity of Ni extraction. More than a half of Ni could be extracted by water when Ni ore was grinded at addition of Na2S207 in the milling treatment. Some effects of mechnocemical treatments to Ni ore are summarized in this paper.

Jan 1, 2005

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By C. H. Bertoni, A. Vachon

The Corner bay copper deposit is the first significan discovery on the south limb of the Dore Lake Complex, located at the eastern end of the Detour Lake-Chibougamau greenstone belt, Quebec. The deposit was discovered in March, 1981, after 26 years of intermittent work in the area. Mineralization is found in a shear zone cut ting rocks ranging in composition, from gabbroic anorthosites to anorthositic gabbros which have been intensely altered and deformed by at least two tectonometamorphic events. Both the copper-bearing shear zone and its host rocks are cut by a large NE-striking gabbro dyke. Most of the known mineralization is found east of the dyke, but two deep exploration holes have shown that the down dip extension is present to the west of the dyke. The mineralized shear varies from one to 15 metres in width, strikes around 010° and dips from 70° to 80° to the west, and has been tested for a length of 700 metres. The wall rocks are usually chloritized and silicified. Mineralization is characterized by chalcopyrite, pyrite, molybdenite, magnetite, and sphalerite occurring mainly as the matrix to quartz-carbonate breccias in the "main" shear zone. The predominant sulphides are pyrite and chalcopyri te as crystals or fragments. The brecciated mineralized shear shows evidence that there was at least one remobilization of the shear and it is suggested that copper-bearing fluids invaded the shear during its remobilization. The exact timing and source of mineralization are not known. Up to February 1984, 38 holes had been drilled to outline indicated reserves to a depth of 450 m of 1,5 million tonnes grading approximately 4% copper, 0.34 gm, gold and 13.71 gm silver per tonne. It is believed that there is considerable reserve potential in the block west of the gab bro dyke, the down dip extension of the main zone.

Jan 1, 1984

By Harry V. Warren

Introduction Any person concerned with the welfare of mining in British Columbia cannot help being perturbed by the fact that the industry, to an alarming extent, is living on its capital. The great majority of mines and mining camps of today represent a heritage handed down by the prospectors of yesterday. It is true that mining engineers, geologists, mineral dressers, metallurgists, and their fellow scientists and engineers have played an honourable, indeed a vital, part in he1ping to make our producing mines, often after costly and extensive underground development and extended researches. It is also true that the mineralization at the Sullivan, Britannia, and Copper Mountain mines was all discovered before the turn of the century. Likewise the Cariboo, Bridge River, Hedley, Ymir, Rossland, Boundary, Slocan, Salmo, and Portland Canal mining areas, although they had not all been developed, were all known more than fifty years ago. Furthermore, every one of these camps owed its discovery and eventual exploitation to the fact that encouraging ' mineralization occurred at the surface. Where would the mining industry of British Columbia be today had those precious outcrops been buried beneath twenty to forty feet of glacial drift or other overburden? Anybody familiar with the geology and geography of British Columbia will probably agree that finding new mining camps is going to be an increasingly difficult and costly business: disappointments there will be in abundance. Nevertheless, most persons will probably also agree that other valuable mines and even mining camps await discovery by those who will prove resourceful and lucky enough to unearth them. It has become increasingly obvious to the authors of this paper that any new too1s which can aid either prospectors or engineers in their search for new orebodies should be welcome. This paper outlines our efforts to develop biogeochemistry and related techniques to the point where they may be considered as useful tools in the search for hidden mineralization.

Jan 1, 1950