Search Documents

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By Carl Lausen

Within recent years several mining companies have sent expeditions co the east end of Great Slave lake co determine the mineral possibilities of that area. Little was known of the geography of the region, and even less of the geology; and, not until Blancher's survey was made and the results published, was an accurate map of the lake available. Early explorers followed the Inconnu channel and the north shore of McLeod bay to Port Reliance, and, just prior to Blancher's survey, Hornby showed that the southern passage was feasible. Apparently, but few geologists have ? travelled through the country, for geological information is meager. In 1900, Robert Bell, of the Geological Survey, made a trip to Fort Reliance by way of the north shore of McLeod bay, and he gives a brief description of the geology. The present paper is the result of an expedition into this little-known region by Mr. Geo. M. Douglas and the writer in the summer of 1928. The south shore of Great Slave lake was followed to the east end of Tochatwi bay, and an extensive exploration was made of Kahochella and Pethei peninsulas. The prime object of the expedition was co determine the presence or absence of the copper-bearing Keweenawan basalts.

Jan 1, 1929

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

By Daniel Lachapelle, Nuri Hmidi, Turgut Yalcin

"Simulation can serve as a convenient tool in studying the behaviour and performance of grinding circuits by facilitating the evaluation of various scenarios and identification of optimum operating conditions. This technique was applied to the St Andrew Goldfields Ltd.’s Stock Mine Mill which is a 1300 tpd gold milling facility, offering custom milling services as well as processing the Company’s own ores. Lack of adequate instrumentation in the mill poses a challenge in attaining optimum performance especially with changing ore types and characteristics. The grinding process is monitored essentially by manual measurement and adjustment of pulp densities at various streams. A simulation program was designed to assist in the effective implementation of this mode of grinding control. Product sizes from both the primary and secondary grinding circuits were correlated empirically to relevant process variables using a database formed from the results of past sampling campaigns. The simulator was created in Microsoft Excel whose data analysis and optimization tools coupled with its Visual Basic Programming capabilities were found to provide an excellent environment for the development of a cost-effective, efficient and user-friendly simulation program.INTRODUCTIONGrinding is often a very costly unit process in milling operations, mainly due to the excessive energy consumption associated with it. For example, for a Canadian copper-zinc flotation mill, grinding was listed as being the most costly item taking up 30.4% of the total milling expenses, followed by the flotation cost at 2 1 .O% (Kidd Creek Mines Ltd., 1982). A survey on 45 copper flotation mills around the world showed the average grinding cost to be 34.5% of the total milling cost (Weiss, 1985).Overgrinding aggravates the cost issue, while insufficient grinding either causes loss of valuable minerals to tails or results in low-grade concentrates. Therefore, it is essential that grinding circuits be carefully controlled and monitored. To this end, a great deal of effort has been devoted over the years to the modelling and simulation of grinding systems in order to assist in the efficient running of these processes."

Jan 1, 2001

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

By Chris Twigge-Molecey

Demand for metals will continue to grow as global population numbers and prosperity levels steadily increase. Consequently, there will continue to be a need to design and construct new metallurgical plants. Business success in general requires projects to be financially successful and return appropriate value to their owners. However, in the metals industry, private and public sector financing sources have become very sensitive to the perceived inability of projects to contain costs and meet other business objectives. Thus, the capital for projects has become more difficult and expensive to obtain. It is instructive to note that Ernst and Young (2011) identified that: “Delivery of predictable project results bestows competitive advantage and market confidence to those corporations who successfully instill this discipline”. The implication for future projects is that they must be systematically developed to minimize perceived risks—and more importantly—to demonstrate that the risks are managed to achieve the business case. Then, provided that the project has been developed in a well-structured way, project success can again be defined as a project with: a final cost within 10% of the budget approved at the end of FEL3, when the project is properly defined and the permit conditions are agreed upon; a start-up date within three months of the definitive, scheduled startup date; production levels at 85% of design capacity within a year of starting commercial operation; production meeting the target environmental restrictions; and with zero lost time accidents during construction and startup. The plant design is one of many integrated activities required to achieve these objectives. This book represents a valuable link between the existing engineering literature that encompasses a wide range of engineering fundamental textbooks and design manuals and the project management literature such as the Project Management Body of Knowledge, or PMBOK® (Project Management Institute, 2014). It is evident throughout this book, that the design team is a small but essential part of a much larger project team comprising the project management, construction management, and construction contractor staff. Design activities must be regarded and managed as part of the integrated whole, with two fundamental links throughout the design process:

Jan 1, 2015

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola's current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006

By F. Crundwell, N. Steenekamp

"The leaching of sulphide minerals generates a significant amount of energy. There are three systems that might be used to remove this energy. These are: cooling coils, quench water, and flash recycle. Flash recycle is the recycling of slurry from the autoclave to the feed tank. Heat is removed in this arrangement when the slurry at elevated temperature and pressure is flashed to atmosphere, releasing steam. The slurry is returned to the autoclave at lower temperature, resulting in cooling. The cooling is directly proportional to the steam released from the recycled slurry. Design equations and results for the flash recycle system are presented. A fourth proposal for removing heat is to recycle slurry from the back of the autoclave. These four alternatives not only remove the heat, but also have an effect on the leaching efficiency. Amongst the four alternatives, design calculations indicate that the flash recycle option is the optimal solution in terms of leaching efficiency and heat removal, and recycling product from the back of the autoclave is the worst. In spite of its efficiency in terms of heat removal and leaching, the implementation of the flash recycle system is limited to a few operations in the platinum industry.INTRODUCTIONIn considering ways to improve leaching operations, focus is placed on the chemistry, on the kinetics, the agitation and perhaps even on the gas mass transfer conditions. Attention is less frequently placed on the removal of energy from these reactors and how this might limit performance.The pressure leaching of sulphides releases a significant amount of heat. For example, the reaction for the leaching of chalcocite, Cu2S, given by"

Jan 1, 2012

By Henri-Louis Jacob

Le secteur des substances non-metalliques repose au Quebec sur !'exploitation et la transformation d'une dizaine de mineraux ainsi que sur la production de materiaux de base destines surtout a l'industrie de la construction. L'ensemble de cette production representait en 1982 une valeur estimee a plus de 797 millions $, soit tout pres de 400Jo de la production minerale du Quebec. L'amiante et Jes scories de titane destines a la production de pigments, qui comptent parmi Jes plus importantes substances minerales produites au Quebec, representent respectivement 370Jo et I 70Jo de la valeur totale des non-metalliques tandis que le groupe des materiaux de construction represente pres de 400Jo. Les autres substances, parmi lesquelles ressortent nettement la tourbe, la silice et la magnesite, representent une valeur totale de 61.5 millions $.

Jan 1, 1984

By Martin Junker

This Notwithstanding all the debates on climate change and renewable energy, coal remains the world's no.1 primary energy source even in the 21st century. In 2011 alone, total output rose from 420 million t to around 6.6 billion t. Similar growth rates are also expected for the next few years. In order to meet demand, new seams are being tapped and others mined far more extensively. In most cases, this means a move from open-cast to deep mining, and extracting coal from ever greater depths. At the same time, extraction processes such as the room and pillar method are being replaced by longwall mining, which significantly increases seam yield and therefore output. The depth of extraction with new, modified mining methods is increasing rapidly around the world - in most countries, much more rapidly than the corresponding expertise. A trade in mining expertise has therefore developed alongside the coal trade proper. Germany relies on coal imports, but can export mining industry services and advanced mining equipment. Geological conditions in the Ruhr and Saar coalfields forced Germany to drive forward development of deep working for hard coal years ago. For 30 years now, Germany has been mining hard coal at depths of over 1,000 m, and excavation is now at depths up to 1,600 m. Deeper extraction and more extensive excavation posed new challenges for both miners and equipment. Intelligent logistics, modern roadway development methods and longwall mining with ploughs or shearers combined with optimised process coordination offered pioneering solutions - solutions to enable costeffective coal extraction in the long term without compromising safety. Countries such as Russia, the Ukraine, China and the Czech Republic, where extraction is now reaching similar depths, can now benefit from this experience: they do not need to go through the same process of trial and development, but can draw on Germany's findings and ultimately save on costs. Now, Germany is offering this knowledge and experience on the international market on a client- and deposit-specific basis to continue providing mining countries with safe and cost-effective coal mining solutions and secure the energy supply. The presentation gives a number of examples of how international mining companies have used expertise from Germany to better meet the challenges of deep mining.

Aug 1, 2013

By Mike Robotham

Drum hoists in the 21st century have the same fundamental objective as their earliest 19th century counterpart. And yet a lot has changed in the design of the hoist from those early days of underground mining. These changes are driven by the need for greater productivity and reliability at ever increasing depths without compromising the all important safety demanded by the industry today. This paper reflects on how these changes have influenced design of a modern hoist Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2013

By C. Edwards

"The processes for rare earth (RE) extraction include the decomposition of RE ore concentrate minerals, and the concurrent or subsequent leaching of the rare earth elements (REEs) from the decomposed minerals. Ore beneficiation concentrate can be decomposed by, for example, acid roasting, caustic cracking, and chlorination. The REEs can be selectively extracted. The nature of the REE extraction process depends on the concentrate mineralogy and the targeted products. Based on the experience of the Saskatchewan Research Council (SRC) in RE processing, this paper reviews REE extraction from the major RE minerals, including bastnaesite, monazite, xenotime, ion-adsorption clay, allanite, cerite, and eudialyte. An update on the development of RE extraction processes is also provided.INTRODUCTIONRE processing usually involves two operation stages, physical processing and chemical processing. Physical processing, also known as ore beneficiation, separates the RE minerals from gangue minerals to produce an RE mineral concentrate. Chemical processing, which includes extraction and separation processes, converts the RE mineral concentrate to an RE compound which is either an end product or an intermediate product for the subsequent production of individual REEs or other compounds. The RE extraction process uses one or more reagents to decompose the RE minerals and to leach the REEs into solution. The RE separation process uses solvent extraction, ion-exchange, or chemical precipitation to produce either rare earth oxides (REOs) or individual REEs. The authors have previously reviewed RE ore beneficiation processes (Zhang & Edwards, 2012). This paper focuses on extraction processes for a variety of RE minerals. Table 1 gives the chemical compositions of the RE minerals mentioned in this paper. The varieties of RE extraction methods use many different reagents. These reagents are mainly inorganic acids, alkalis, salts, and chlorine gas. The commonly used acids include sulfuric acid (H2SO4), hydrochloric acid (HCl), and nitric acid (HNO3). Sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) are the most common alkalis. Salts include ammonium sulphate ((NH4)2SO4), ammonium chloride (NH4Cl), and sodium chloride (NaCl). HCl is normally used to extract RE from silicate ore minerals such as allanite and gadolinite. The alkalis and H2SO4 are mainly used to leach REs from phosphate ores minerals like monazite and xenotime. The carbonate ore RE minerals such as bastnaesite can be treated using either acids or alkalis. HNO3 is mainly used to leach eudialyte and apatite. The extraction of REs from ionadsorption clay deposits uses salt solutions. Chlorine gas (Cl2) is exclusively used in the RE chlorination process which can be used to treat any RE minerals."

Jan 1, 2012

By J. E. Hawley

"The zinc-lead deposit of the Lake Geneva Mining Company is on lot 7, con. VI, Hess township, Sudbury district, Ontario, about 10 miles northwest of the northern rim of the Sudbury Basin. Though a relatively small deposit, it shows some rather interesting relations to cross-cutting, pre-ore, quartz diabase dykes, which merit description.The deposit was discovered in October 1924 by J. H. Collins beneath iron-stained drift and oxidized sulphides. This proved to be the northwestern extremity of the orebody, the remainder of which extends southeast below swampy ground. Exploration began in 1927. In 1928 a vertical shaft was sunk to 250 feet and a level established at 235 feet. Later the shaft was deepened to 400 feet and new levels opened at 315 and 375 feet. In 1943 an inclined winze was sunk below the vein from the 315-foot level to a vertical depth of 640 feet, and two additional levels were opened at 525 and 615 feet respectively.The geology of the area has been described by T. T. Quirke (1), F. F. Osborne (2), F. J. Alcock (3), and Ralph Tuck (4). Private reports have also been made by Carl Tolman, J. E. Gill, and K. W. Fritzsche. Tuck's paper, covering the work completed to 1930, gives a detailed account of the character of the ore and enclosing rocks.Up to May 1944, when the property was closed, all ore above the 375-foot level and a small tonnage from below this elevation had been removed. Ore mined from 1941 to 1944 yielded the following:"

Jan 1, 1954

By Stephen van Duin

As productivity in coal extraction demands increase in underground coal mines, the industry is faced with finding new ways to support production without jeopardising safety. In modern mines the capacity and scale of longwall coal extraction has steadily increased to a point that support processes are failing to keep pace. In particular, roadway development is continually placed on the critical path of activities which maintain mine production, so any inefficiency in this area is quickly exposed. Original equipment manufacturers are under immense pressure to modify their machines to be more interconnected with each other, with machine communication and logistical sharing of space becoming a known requirement. This paper looks at the changing trends in mining practice, analysing available technology as well as currently emerging research into hard automation and discusses the need to integrate machinery and processes in order to see increases in productivity and safety.

Aug 1, 2013

By J. F. Davis

Pegmatite dykes containing lithium minerals and beryl occur dose to the borders of intrusive masses of granitic rock in the Winnipeg River area of Manitoba. Both vertical and flat-lying dykes are present. Most of the pegmatites consist of zones, containing characteristic mineral assemblages, arranged more or Jess parallel to the borders of the dykes. Five important lithium minerals are present; each occurs in a separate zone, but all the lithium-bearing zones are situated toward the centres of the pegmatites. Spodumene is the most abundant and widespread of the lithium minerals and occurs as small crystals intimately intergrown with quartz. Beryl is not an important constituent of the lithium pegmatites, but when .present, occurs outside the lithium zones, toward the margins of the -dykes. Beryl is most common in dykes containing few or no lithium minerals. The mineral assemblage in the beryl zone of the lithium dykes is the same as that of the beryl dykes. The attitude and internal structure, particularly zoning, of the pegmatite dykes, and the texture and assemblages of the constituent minerals, have an important bearing on exploration, development, and mining of these pegmatites, and on the extraction of various mineral products from them.

Jan 1, 1958

By Geir M. Haarberg

Electrochemical techniques, mainly linear sweep voltammetry and potential step chronoamperometry, were used to study the behaviour of dissolved phosphorus species in cryolite-alumina melts, The presence of AIPO4 or Na3PO4 gave rise to voltammetric current waves due to electrode reactions involving phosphorus species at potentials where dissolved alumina is stable in cryolite melts, Diffusion kinetics for dissolved P(V) species were studied, Data from industrial cells were used to determine mass balances for phosphorus, For cells being fed with secondary alumina, more phosphorus tends to end up in the produced metal, Laboratory experiments to study the effect of phosphorus in the bath on the current efficiency for aluminium were also carried out.

Jan 1, 2004

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By N. Ginouse, S. Reny

"In the mining industry time is critical as production depends on the speed of the mining cycle. During the mining process, the time required to re-open access for the next phase of an underground heading is a key point that strongly depends on the ability of the selected ground support technique to promptly ensure the safety of workers. Fiber reinforced dry-mix shotcrete has been proven to be an efficient and well adapted technique, able to produce a ground support material with the required energy absorption or flexural toughness in a single application phase. In this context, this paper demonstrates the possibility of significantly speeding up the mining process by using a new fiber reinforced dry-mix shotcrete. The new fiber reinforced dry-mix shotcrete is capable of developing flexural toughness in only 24 hours that is equivalent to what is typically achieved after 28 days using current fiber reinforced drymix shotcrete technology.INTRODUCTIONShotcrete is often used for ground support when using the drill and blast method or other tunnelling methods. But before re-opening access for the next phase of the underground heading, the applied shotcrete is required to reach a minimum compressive strength and in case of fiber reinforced shotcrete, a minimum flexural toughness (energy absorption) in order to ensure the safety of the workers going into the heading. Combined with bolts, the use of conventional fiber reinforced shotcrete becomes an interesting method for ground support as it is applied very soon after excavation and works to stabilize ground movements (Bernard E. S., 2009). In this case, the toughness development of fiber reinforced shotcrete becomes an important feature of the material when looking to speedup the mining cycle. However, early re-entry criteria in underground openings are difficult to ascertain as the load carrying capacity of fiber reinforced shotcrete is usually assessed after 7 or 28 days. For this reason, re-entry criteria varies from one mining area to another and are usually based on compressive strength requirements. For example, in northern Ontario, Canada, one of the current practices in the mining industry consists of allowing safe re-entry once fiber reinforced shotcrete has developed a compressive strength of higher than 4 MPa (Dufour, O’Donnell, & Ballou, 2003). Flexural toughness requirements on fiber reinforced shotcrete are also typically based on evaluation after 28 days."

Jan 1, 2015

By C. Moctezuma

Since the start up of the IMMSA electrolytic zinc refinery in 1982, the dissolved iron coming from the acid attack of the ferrites has been precipitated by the jarosite process. At the beginning of operations, sodium jarosite was produced; however, the plant was converted to ammonium jarosite in 1990. The final storage of the residue is on the company&apos;s property adjacent to the plant, over the natural surface of the land. Before the construction of the refinery, several studies were done in order to evaluate the characteristics of the ground, such as, permeability, underground water localization, etc. The results showed that the site was adequate for the storage of this kind of material. For several years, the jarosite residue was filtered on rotary drum filters and was sent as a pulp to the storage area for settling. The water from the storage pond was recycled to the re-pulp tank for the jarosite residue. These filters were replaced in 1999 by an automated filter press. Since then, the jarosite residue has had a lower water content, and the zinc recovery improved. At present, a second filter press for the jarosite circuit is in the acquisition process to diminish the soluble zinc content in the residue from the present value of 2% to < 1% Zn.

Jan 1, 2006