Search Documents

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By Roxanne Scott

Outline ? Overview of Community Investment in the Mining Sector ? Emerging Good Practice: ?Strategic Integrated Community Investment? ? Assessing Local Context: ? Institutional Assessment ? Partnership Assessment Approaches to Community Investment Isolation: No proactive engagement in community development Ad hoc philanthropy: small infrastructure, sponsorships, donations Strategic philanthropy: Community proposes options for development Company decides what to do and carries it out, e.g. building schools, health posts, roads Strategic integrated community investment: ? Aligned with government/community development goals and priorities ? Communities and government involved in decisions and execution ? Focused on training and capacity building ? Partnerships ? Continuation in absence of company support Measured returns on investment

May 1, 2010

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By The Staff

The San Anconio mine, owned by San Antonio Gold Mines, Limited, is located on the north shore of Rice lake, thirty miles east of lake Winnipeg, and about one hundred miles northeast of the city of Winnipeg. The three claims which formed the original San Antonio group were staked in 1911. Subsequent additions to the Company's property have in-creased their holdings co thirteen claims. Preliminary development of the property took place between 1925 and 1930. The major ore discovery during this period was the 16 vein. The mine was closed in September, 1930, but re-opened in April, 1932, since which rime it has been in continuous operation. In 1933, a development of special importance was that of the 26 vein. The mill capacity, originally designed for 150 tons, was increased to-wards the end of 1933 to 170 tons. With highly satisfactory mine development, mill enlargement to approximately 300 tons was made possible. The Company has financed the additions and improvements from mine production. Iris of interest to note that San Antonio is the first gold mine in Manitoba to pay a dividend. The first dividend was paid to the shareholders in March, 1934, and the fourth was recently declared. Electric power is transmitted to the property from the Great Falls plant of the Manitoba Power Company over a 66,000-volt transmission line approximately 62 miles long. The old camps, which had been in use since work on the property was started, in 1927, were demolished in the spring of 1934, and new camps were built on the Ross dam. Lumber for these buildings was out at the Company's saw-mill on Gold creek, eight miles from the mine. Two bunk-houses with a capacity of 72 men each were constructed, also a dining room co accommodate 144 men, a store, staff house, hospital, burcher shop, and warehouse. The camp buildings are all steam-heated from an electric boiler. They are all insulated on walls, roofs, and floors with a heavy building board, and are covered on the outside walls with asbestos siding, and on the roofs with corrugated iron. A community of about 800 persons has grown up around the mine, at Bissert. Attention has been given co their social interests, and the management of the mine has assisted its employees co build a community hall, which is used for dances, picture shows, and other entertainments and amusements. A two-room school, with an attendance of 50 pupils, is supported by Company employees. In addition, picnics, boxing contests, and hockey games are encouraged among the employees.

Jan 1, 1936

By D. C. Crothers

"What is new in air compressors? A good deal - the designers have been keeping pace with technical developments in related fields and also contributing new techniques of their own. Plant reliability no longer requires bulky slow-speed machines. Even the reciprocating machines, which still provide the most efficient method of compressing air, have been greatly reduced in size and installation cost for a given capacity rating. New materials and fabrication techniques are being used, by most manufacturers, to produce less costly plants in total. Many packaged plants are available, which generally means a more complete assembly for shipment. This type of construction offers savings in handling and erection costs at the site. A warning is in order, however - the extent of packaging in any given plant should be investigated carefully to determine what is included and just what field costs can be realized. A suggested specification has been offered for consideration when studying comparative costs. Rotating machines intrigue many because of their potential as regard fewer wearing parts, higher speeds and hence smaller units, utilizing less expensive drivers, and lack of contamination of the compressed air by lubricants. The inherent shortcomings of these machines - lower •efficiency and capacity control - have been much improved lately, and this type of plant is now becoming quite popular. Noise control, of much concern to everyone, is another development that has received considerable attention.Systems for efficient capacity control and continuous monitoring of compressor operation offer additional reliability and low-cost operation of the modern compressed air plant. Accessory equipment and its effect on over-all plant operation is also considered."

Jan 1, 1972

By M. Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

Jan 1, 2005

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

By X. -G. Chen, K. Liu

Nowadays, great interests are rising on aluminum alloys for the applications at elevated temperature, driven by the automotive and aerospace industries requiring high strength, light weight and low cost engineering materials. As one of the most promising candidates, Al-Mn-Mg 3004 alloys is found to possess considerably high mechanical properties and creep resistance at elevated temperature resulted from the precipitation of a large number of thermally stable dispersoids during heat treatment. In present work, the effect of Fe contents on the evolution of microstructure as well as high temperature properties of Al-Mn-Mg 3004 alloys has been investigated. Results show that the dominant intermetallic changes from a-Al(MnFe)Si at 0.1 wt.% Fe to Al6(MnFe) at both 0.3 wt. % and 0.6 wt. % Fe. In the Fe range of 0.1 to 0.6 wt.% studied, a significant improvement on mechanical properties at elevated temperature has been observed due to the precipitation of dispersoids, and the best combination of compression strength and creep resistance at 300°C is obtained in the alloy with an intermediate Fe content (0.3 wt.%) with finest size and highest volume fraction of a-Al(MnFe)Si dispersoids. The superior properties obtained at 300°C makes 3004 alloys more promising for high temperature applications. The relationship between the Fe content and the precipitation of stable dispersoids as well as the materials properties has been discussed.

Jan 1, 2015

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

By D. M. Wyslouzil

"Micron or sub-micron size gold inclusions in sulphide minerals cannot be extracted by conventional cyanidation. The gold surfaces must first be exposed by decomposition of the sulphides. As an alternative to roasting, pressure oxidation was found to be a most satisfactory method to decompose the sulphides and expose the gold particles. For cyanidation the pressure oxidation pulp has to be neutralized and stabilized with lime. It was found that thiourea can extract the gold directly from the pressure oxidation pulp without pH adjustment and oxidant addition. The main obstacles against the common use of thiourea are circumvented by a recently described control method of the emf during leaching.INTRODUCTION Amalgamation and cyanidation are the most conventional processes for gold extraction. The prerequisite for gold extraction is the possibility of gold surface to be contacted by mercury or by the cyanide solution. Encapsulated gold has little chance of contact and this leads to poor extractions.The reasons why a gold ore may be refractory are: micron or sub-micron size gold particles included in the sulphide minerals, such as pyrite and arsenopyrite; presence of and association with antimony, arsenic, tellurium and carbonaceous minerals. Some alternative processes, such as double oxidation(1,2), pretreatment with lime , H202, chlorine and Caro's acid, roasting and thiourea leach, have solved some of the problems of ""refractory"", but the sub-micron gold in sulphide minerals still shows little response. Roasting and the cyanidation of the calcine was one of the most successful approaches for this type of gold ore.There are two disadvantages to the roasting process: (1) the generation of sulphur, arsenic, antimony and mercury containing gases is undesirable and the control is extremely expensive; (2) gold particles might be fused in the roasted product and the oxidized base metals in the calcine might reduce the cyanidation efficiency. In recent years the pressure oxidation process has been considered as one of the more effective and satisfactory methods to decompose the sulphide minerals and expose the gold surface to the cyanide leach solution. The pollution problem could be better controlled and the gold extraction is more amenable."

Jan 1, 1985

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By P. Bousquet

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian mining industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (e.g., pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2002

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017