Search Documents

To provide suitable backfill material for the cut and fill mining method being used to extract ore from the C.S.A. mine, flotation tailings are deslimed in single stage cyclones. The sand fraction is stored on the surface in unagitated storage bins before being pumped underground, while the slime portion is thickened and pumped to a residue dam. Design and operating details of the sand preparation and storage sections are given.The initial preparation of a stope for filling, consists of laying percolation and decantation drainage pipes on the sill floor. Preparation for fllling of subsequent lifts consists of rearing up the ventilation pipes at the ends of the stope, preparing the decantation system, and building a barricade or wall. The fill is carried to, and discharged into, the stope through 4 in. diameter pipes and filling of any section is carried out 24 hr/day normally without supervision. The fill is retieulated underground to the 1200 ft level through rubber lined pipe installed in the upcast shaft. Boreholes of 3 in. diameter drilled from the1200 ft level convey fill to the 1800 ft level. The mine drainage system is basically designed to handle the water associated with hydraulic filling. A system of primary and secondary sumps has been installed to handle the percolation and decantation drainage from stapes and to allow settling of fines before the water is fed to the main pump station.A programme of investigation into the properties of the emplaced fill is in progress. Results to date indicate that the fill as presently placed and drained, will not cause any problems in the mining of vertical orebodies by cut and fill methods for lifts in excess of 300 ft.

Jan 1, 1969

With the advent of the resources boom in the late-1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large-scale Australasian open pit mining generally.

Jan 1, 2002

By Howard G. L

The gold treatment plant of Great Western Consolidated N.L. is at Bullfinch, Western Australia, 22 miles north of Southern Cross, which is 100 miles west of Kalgoorlie. A railway to Southern Cross connects the mine with the main Perth-Kalgoorlie line.The plant, which commenced operations on the 31st October, 1952, was, designed by Messrs. Alex: Stewart & Co. in consultation with the technical staff of Western Mining Corporation Ltd. to treat 1,000 long tons a day, made up of approximately equal parts of quarry oxidized ore and underground sulphide ore, by moderately coarse grinding (2-3 per cent plus 65 mesh Tyler) and straight cyanidation without straking. The design had to allow for future treatment of all sulphide ore at the rate of 40,000 tons per 28-day periodand to make provision for the possible later inclusion of preaeration treatment.The test work on .which design was based was done on representative development samples, the mine being divided into zones for this purpose, to check possible local variations from average treatment behaviour. Proposed mill feed mixtures were made up from time to time for complete ore dressing tests, which were conducted in the Western Mining Corporation laboratory at Kalgoorlie.The chief feature of the design was that the plant had to handle the extremes of very soft, poor settling and filtering oxidized ore and very hard, good settling and filtering sulphide ore. On one hand, crushers and mills had to be large enough to handle the sulphide ore and on the other, thickeners and filters had to be large enough to handle the oxidized ores.The design is marked by simplicity, the use of large units of equipment, and flexibility to cope with a variety of ores.

Jan 1, 1956

By Heyes GW, Orrock GI

The fine grained complex orebody at Elura contains galena, silver and sphalerite in a matrix which is mostly pyrite; sulphides account for about 90% of the orebody. A differential flotation circuit is operated to con- centrate lead and silver in the first section and zinc in the second. The metallurgical performance to date indicates the need for improvement. The lead section has been sampled in detail to comprehensively assess its overall performance and to define problems associated with lead and silver flotation. The substantial amount of pyrite in the feed dominated the perfor- mance of each stage of the separation. It was responsible for extensive dilution of all concentrates and, as a consequence, for very large circulating loads. The rougher concentrate contained 68% pyrite some of which was rejected through the three stages of cleaning to 39% in the final concen- trate. However, this was still sufficient to hold the assay of this product below 45% Pb. Size by size behaviour shows that flotation rates of the valuable minerals, as characterised by their rate coefficients, were low through- out the circuit. There was a significant deterioration in these rates between rougher and cleaner I stages which resulted in large circulating loads between these stages. There was practically no recovery of coarse valu- able minerals to the final concentrate. The dilution of the final concen- trate by non-sulphide gangue was not a major problem. If the recovery of the galena and silver in the +38¦m size range could be raised to that of the - 381Lm size range, galena recovery would rise from 78% to 86% and silver recovery would improve from 46% to 59%. The Pb grade of the final concentrate would remain the same.

Jan 1, 1988

The Myally Beds, Surprise Creek Beds and Mount Isa Group form the upper part of the Proterozoic Western succession of rocks in northwest Queensland. The latter two units are partly equivalent, and are important for their base metal content at Mount Isa and elsewhere. The arenaceous Myally Beds lie unconform- ably or disconformably below the Mount Isa Group and Surprise Creek Beds; they contain four mappable units which were deposited on a broad, shallow shelf washed by east-trending currents. Emergence of the Myally shelf initiated a series of parallel, possibly intra- cratonic, troughs to the east and west. In the east, the Surprise Creek Beds were deposited between the emergent shelf and base- ment rocks, and consist of a shelf and trough facies divisible into 7 and 10 units, respectively. Trough sediments are continuous north-south, and show turbidite character- istics; algal dolomite characterizes the shelf facies. To the west in the Mount Isa trough, an orthoquartzite facies, the Warrina Park Quartzite, defines the base of the Mount Isa Group. Hinge zones between the shelf and trough environments are marked by east-west facies changes, and provide a focus for later major north-south faulting. However, some penecon- temporaneous faulting near Mount Isa is best explained as complex post-depositional faulting of a disconformable sequence. Subsidence and deposition in the Mount Isa trough continued for a longer period than in the Surprise Creek trough, allowing accumulation of lead and zinc deposits in the upper half of the sequence. The Surprise Creek Beds appear equivalent to the lower half of the Mount Isa Group, and are probably not prospective for lead and zinc. Turquoise and possible other secondary copper minerals are widespread in the Warrina Park Quartzite and equivalents in the Surprise Creek Beds, and further investigation of these formations seems warranted.

Jan 1, 1974

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

By Chung S

The problems associated with equating calculated and measured properties of explosives with blast results are examined. The results from six full-scale test blasts in a limestone quarry are described. The purpose of the full-scale trial was two-fold, i) assess the role of varying aluminum levels (10% maximum) in a given explosive in terms of blasting performance, and, ii) find correlation between calculated, as well as measured properties of explosives and the resulting blasting performance. Each blast consisted of 36 holes, initiated with short period detonators in a staggered 3-row 2.4 m x 2.7 m (burden x spacing) pattern. Each 75 mm diameter borehole with no subgrade contained on the average 22 kg of 65 mm diameter cartridged explosive. The bench height was 6.3 m, with an average collpr of 1.2 m. The calculated and mgasured properties of explosive included, strength, detonation and explosion pressure, VOD, plate-dent depth, underwater bubble and shock energy, and the total energy efficiency. Each blast was instrumented to measure detonation velocity, initiation sequence, muck pile motion by means of high-speed photography and blasting vibrations. The post-blast measurements included photogrammetric survey of muck pile for size distribution on surface, muck pile profile, as well as the extent of backbreak. The results showed that the overall blasting performance of the explosive in question was nearly commensurate with the level of aluminum in the explosive, and there was excellent correlation between the underwater test properties and the blast results. The study also exemplified the need for more extensive post-blast analysis than is usual practice, for quantitative assessment of blasting performance of explosives and providing the necessary data-base for calibration of blasting models.

Jan 1, 1990

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

By U Rehm

The biggest hard rock double-shield tunnel boring machine (TBM) in the world, with a diameter of 12.4 m, is currently excavating the North-South Bypass, which includes a crossing under the Brisbane River, Brisbane, Australia, to relieve the often congested road traffic in the city centre. Ten years ago a 10.7 m Mixshield giant helped to handle the Olympic Games in Sydney linking the airport with the city centre for an improved transportation of fascinated visitors. In Shanghai, currently the biggest TBM in the world with 15.43 m diameter presents excellent performance rates; and in Paris a convertible Mixshield could be quickly changed from earth pressure balanced (EPB) to slurry type in order to handle the very heterogeneous ground conditions. In Madrid a 15.2 m EPB giant finished its tunnel job four months ahead of schedule. Large-scale TBMs have proved their economic and innovative potential to create the current and future underground architecture of mega-cities. TBM technology has made further large innovative steps in the last decade. State-of-the-art is a TBM for very heterogeneous ground conditions comprising hard and soft rock with additional high groundwater pressure. The machine concept is adapted to the various ground conditions and allows for a quick and flexible application. Ground treatment by means of additives developed to a helpful tool in this connection. To meet the special challenges of urban tunnel projects of nowadays it is of very high importance, beside applying highest developed technology of TBM, to have a comprehensive technical support during the project phase and to develop positive relationships between all participants of the project which last longer than only for one project.

Jan 1, 2008

By R Farnf, M Pegden, S Hosein, T White

A number of theoretical papers have been published outlining the use of electronic detonators to limit peak particle vibrations levels, but few empirical studies have been undertaken and even fewer examples have been published of the use of such technology in the aggregates industry. This paper gives a summary of the research work carried out at two limestone quarries in the North of England, where a series of blasts were used to compare and contrast the use of electronic and non-electric detonators. The majority of blasts were carried out using the same burden, spacing and decked charge weight loadings. A methodology was established that could be used to reduce the peak particle velocities (PPVs) at two or more specific locations by using single-hole blast vibration signatures in conjunction with specific electronic detonator timing intervals. The initial study concluded that this was only possible if single-hole signature blasts were periodically recorded to establish the shape of the correct vibration envelopes as properties were approached. These wave envelopes could then be used as the basis for choosing the specific electronic detonator timing intervals to give the lowest PPV for the properties or locations concerned. This methodology was then used in the second study to access a large volume of aggregates adjacent to a working railway tunnel. The financial benefit for the company was to convert these additional tonnages of rock from being a resource to an exploitable reserve. The project involved careful blast design and the instrumentation of a number of boreholes to enable the results of blast monitoring exercises to be compared with predicted PPV results. The iterative process involved the vibration results being uploaded into æBlast LogÆ (an expert blasting database system developed by the Blasting and Environmental Research Group at the University of Leeds) and analysed to produce predictions ready for the next blast.

Jan 1, 2007

By H Arvidson, D Guibal

This paper presents updated interpretations of controls on mineralisation in C Deposit and highlights structural features that influence the geometry of mineralisation domains used in resource estimation. The Area C mining lease is located in the central Hamersley Province, ~100 km WNW of Newman, Western Australia, and contains resources of approximately 1100 Mt of Marra Mamba and Brockman iron mineralisation. C Deposit is located within Area C, on the northern limb of the Weeli Wolli anticline, and mineralisation is hosted predominantly in the Mt Newman Member of the Marra Mamba Formation. Production from C Deposit began in August 2003, following mining of a 950 000 tonne bulk sample in 2002. Recent mapping in the bulk-sample pit and updated interpretations by BHP Billiton geologists have highlighted the significance of structural controls on mineralisation in C Deposit and their influence on the thickness of mineralisation, which ranges from 20 to 80 metres. Structural controls on the geometry and continuity of mineralised domains include south-dipping thrust faults that developed along the Mount Newman/West Angela contact, folds associated with thrust fault development, steeply dipping stratigraphic contacts in the hanging wall of the thrust faults, and gently north-dipping stratigraphic contacts. Thrust faults and folds in C Deposit are significant for two main reasons: their formation resulted in the thickening of the main ore-hosting units in the Mount Newman Member; and faults and folded stratigraphic contacts provided conduits for supergene metasomatic-enrichment processes that produce high-grade iron mineralisation.The implications of this interpretation for the definition of the resource estimation domains are discussed, and suggestions are made for a better integration of geology into the data acquisition and estimation process.

Jan 1, 2005

By M Thomas, M Caccetta, C Laukamp, A Hacket, M Jones, A Rodger, M Verrall, R Hewson

A mineral systems approach was used to interpret precompetitive airborne mineral mapping geoscience data for iron oxide copper gold (IOCG) exploration in the Starra area, Eastern Succession, Mount Isa Inlier. Selected minerals were chosen to map possible source rocks/fluids as well as intersecting structural/fluid pathways that could have transported mineralising fluids into domains of contrasting rocks/fluids where there was potential for physicochemical gradients to precipitate metals. Ferric and ferrous iron contents and white mica abundance were useful mineral criteria to identify theMount Dore Granite of theWilliams-Naraku Batholith as a potential source of æoxidisedÆ fluids rich in Fe, K and potentially Cu-Au. The Mount Dore Shear Zone (MDSZ) intersects the western margin of this granite with the highest contents and changes in composition of the white mica are peripheral to this contact within the granite. This together, with the fact that the entire N-S length of the MDSZ in the study area (~16 km) is abundant in white mica are evidence of K-rich fluids had preferentially moved along this pathway. To the south, the MDSZ intersects a domain comprising massive ironstone bodies as well as numerous graphitic horizons. This interpreted æreducedÆ domain is well mapped using the æopaqueÆ mineral products, as well as by white mica, which is pervasively developed and extends 2 km either side of the MDSZ fault into the meta-sedimentary sequences. The chemistry of this white mica also changes progressively away from the MDSZ, becoming more Si-rich (longer wavelength) towards the contact with massive ironstone bodies in the west and the graphitic units in the east, both of which represent sites of known Cu-Au mineralisation. Beyond these contact zones of interpreted æoxidised fluidsÆ with reduced rocks/fluids, there is either a rapid change to Si-poor white mica and/or no white mica developed, ie major æchemicalÆ gradient change. These mineral mapping results provide evidence for a direct link between possible source rocks and sites of IOCG metal deposition as well as extending the associated alteration zonation which had previously been mapped/published at the metre-scale to the kilometre-scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Since the 1970s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. We now see a similar trend towards sustainability. The Brundtland (1987) definition of sustainable development provides a direction for advocates: the advance of human prosperity in a way that does not compromise the potential prosperity and quality of life for future generations. In my view its three essential components are: economic, environmental and community. The Global Mining Initiative and the contributions to the Rio World Summit and the Johannesburg World Summit on Sustainable Development indicate that sustainability is being taken very seriously by the mining industry. But does the minerals industry really embrace sustainability as they claim? There is a view that in reality sustainability is a non-event and that the triple-bottom line approach is only a convenient catch-cry for companies who are actually focussed very strongly on the economics part of the equation. Chemical engineers are showing a strong trend to more sustainable practices and the chemical industry has shown real commitment to research into developing sustainable processing systems. This requires a framework for thinking and design and the chemical industry is demonstrating true innovation as it moves towards æno wasteÆ technologies. Whilst there are limits to the rates of change that can occur the minerals industry should also be moving in a much more determined manner towards the notion of processing of products designed for whole-of-life cycle û with minimum/no waste. But is the minerals industry just paying lip service to the importance of research to sustainability?Several common themes influence the science and innovation agenda in Australia, which will affect the development and adoption of innovations by AustraliaÆs minerals sector. First is the well-proven link between peer-reviewed scientific excellence and commercial application. Second is the rise of multi-disciplinary Mode 2 research, which has developed in response to the complexity of problems faced by contemporary researchers, which are best analysed by combining expertise from two or more disciplines. Successful innovation outcomes, in any field, including minerals processing, is promoted by Mode 2 research which benefits from greater levels of networking and collaboration. Kofi Annan in his Message to the World Social Forum puts it very succinctly æThe way forward lies in finding constructive solutions togetherÆ.

Jan 1, 2004

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

The purpose of the Lower Lea Valley Cable Tunnel project is to relocate the overhead power lines circuits, which currently cross the proposed site for the 2012 London Olympics in East London. This was the first contract to be awarded as an Olympic project and is on the critical path for the proposed Olympic Park as the construction of the Olympic village, stadium and other venues cannot begin until the tunnels are complete, the cables installed and the overhead power lines removed. The tunnelling works for the scheme include two parallel tunnels between Hackney and West Ham. Each tunnel is approximately 6 km in length. One tunnel is 4.15 m ID and connects the National Grid substations. The other is 2.82 m ID and connects the EDF Energy substations. The tunnels were constructed through mixed ground using four earth pressure balance tunnel boring machines. These were driven simultaneously from two drive shafts within a single site. The 12 km of main tunnels were constructed within a year from start to finish, with completion in June 2007. The shafts range between 6 m and 15 m ID. These were constructed using a combination of caisson sinking and underpinning techniques. Dewatering was adopted to suit the groundwater conditions.Other works include the design and construction of the head house buildings, cable and ventilation culverts, mechanical and electrical (M&E) installations and all associated works. In addition to the above, a further 1 km of tunnel and two shafts were added to the project scope connecting the EDF Energy tunnel to the substation at Bow. These additional works provided further challenges to the project to ensure that these works were constructed within the program constraints for the 2012 London Olympics. This involved refurbishing one of the tunnel boring machines from the main EDF Energy tunnel drives and relaunching the machine to construct the Bow tunnel. The Bow tunnel was constructed within two and a half months, with the tunnel boring machine breaking through in August, ahead of schedule. The main challenge presented by this project is the program constraints. This project outlines the requirement for team work between the client, stakeholders, contractor and designer in order to provide program certainty. A close working relationship between the contractor and the designer is required to provide value engineered, time-saving solutions to mitigate the risks associated with the design and construction program.

Jan 1, 2008

By Andrews B. S

The sinter plant at the Sulphide Corporation's Cockle Creek works produces a feed for the company's Imperial Smelting Furnace. The feed contains lead and zinc oxides and all the fluxes necessary for furnace operation. The quality of this feed is a major factor in furnace performance and the considerable flexibility of operation possible at the sinter plant has been used in efforts to achieve optimum operating conditions.Operating data is processed daily and information gathered from this source has led to three of the four improvements described.These improvements have resulted from elimination of gas recirculation, reduction of sinter returns sizing and alteration of ignition conditions and main layer fuel loading.

Jan 1, 1964

The hydrological cycle in nature, with particular reference to Australia . 2. The definition of water pollution drawing on the experience of several major countries. 3. A description of the pollutants in water, and why they are pollutants. 4. The classification of waters as defined by major overseas countries. 5. The criteria and standards developed by major overseas countries for the classification of waters. 6. A brief- summary of the legislation adopted by overseas countries for the control of water pollution, and of the organisation and administration of controls. 7. A study of Australian legislation and administration of controls of water pollution. 8. General observations and conclusions.

Jan 1, 1971

Mr. Chairman, Distinguished Guests, Ladies and Gentlemen. I was delighted to be invited, and to accept the invitation, to welcome to this specialist meeting on an intriguing subject, the local participants and - most importantly - the international contributors. Technical o analysis of blast furnace operations has for many years formed the basis of intense research throughout the iron and steel industry, world wide, because the efficiency of blast furnace operation estab- lishes the foundation for all subsequent processes in a steel plant. So much depends on the constant, efficient performance of iron melting units in relation to costs, quality, regularity of operations and reli- able delivery performance to our customers.

Jan 1, 1981

I am honoured to have been asked by Sir James Foots, the President of the Congress Organising Committee, to open this, the 13th Congress of the Council of Mining and Metallurgical Institutions. The theme you will be addressing over the next few days is "The Twenty First Century - Mining, for Mankind" - a theme that must be regarded as an enormous challenge for the entire minerals industry. Previous conferences, starting in 1924 in London and followed by two others in the United Kingdom, have also taken place in Canada (three), Southern Africa (three), Australasia (two), and Hong Kong (one), but this is the first to be held in Singapore.

Jan 1, 1986

By Morland R, Peck R

The Joint Committee of The Australasian Institute of Mining and Metallurgy (AusIMM) and the Australian Mining Industry Council (AMIC) have published a Code for the Reporting of Identified Mineral Resources and Ore Reserves. The Code is the result of an initiative begun in 1971 to achieve industry self regulation of Resources and Ore Reserves reporting which resulted first in guidelines for reporting standards but which have now been incorporated in ASX Listing Rules as a Code with significant sanctions ensuring compliance. This paper describes the background to the Code, its key provisions, and comments on practical aspects of working with the Code and compliance issues.

Jan 1, 1990