Search Documents

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

By J-P Franzidis

Hydrodynamic conditions such as gas dispersion, mixing intensity and solids suspension are known to govern the metallurgical performance of the flotation process. Understanding flotation cell hydrodynamics is therefore important for the optimisation of existing cells and for the design of the larger and more efficient cells which are needed to handle the finer, lower grade ores currently being mined. This paper presents the results of numerous studies that have been carried out to characterise the hydrodynamic conditions in a number of different types of flotation machines both in Australia and South Africa. Measurement techniques that have been developed to determine gas dispersion and other hydrodynamic properties in industrial flotation cells are described along with applications for their use. The results show distinct differences between the way flotation cells are operated in the two countries.

Jan 1, 2000

By Siemon J. R

It is possible to use compacted anodes formed at low pressure for the direct electrowinning of lead from sulphide concentrates. An anode containing 5.5 per cent graphite, formed into a compact at 34 MN m-2, enables lead to be won at a current efficiency of about 80 per cent; the power consumption .at 150 A m-2 current density being 0.4 kWh per kg lead. It would be necessary to use diaphragm cells to obtain a sufficiently pure product. A conceptual design for a full-scale plant is presented, together with a cost estimate for the production of lead by a process based on direct electrolysis of compacted concentrates. It is unlikely that the proposed process will be economically competitive with the conventional lead smelting.

Jan 1, 1976

By Mills JC, Belcher CB

X-ray fluorescence spectrometry is used videly for routine quality control of the mining, )lending and agglomeration of iron ores. Most )f the procedures used, cannot tolerate significant changes in matrix composition or be Lpplied to a wide range of elements. Accord- ngly, a graphite briquette technique which is Lpplicable to some fifty elements in widely Tarying iron ore matrices is described. The ignificant advantages are suitability of the ame preparation for both optical emission and -ray spectrometry, a complete elemental overage for the range 5bcg/g to 100%, and the recision and accuracy of the methods are om.parable with the standard chemical.methods hich have been superseded in the authors' boratories. The proposed methods become ore attractive and economical as more prehensive information is sought.

Jan 1, 1975

In Europe there are many regions, where coal or lignite is mined with surface methods. In most of these regions coal/ lignite is mined below groundwater table and mining opera- tions require pumping big volumes of water. Drawdown of groundwater table has influence on surface water and ground- water on adjacent areas. Mine drainage requires purification and its discharge changes flow in existing streams. Some of mine water is used by mining companies themselves, some is used by other industries, some for communal purposes and some for irrigation. However, majority of mine water is dis- charged to rivers without use. The above issues are discus- sed on the background of general, technical and water charac- teristics of such regions in B European countries. Conclu- sions and prospects for future complete the paper.

Jan 1, 1988

By M D. Boscardin, P A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County involves TBM tunnelling twin light rail tunnels through cohesive soils and rock under the Allegheny River and a narrow city street. Along the tunnel alignment are a listed historic building on shallow foundations as well as modern buildings on deep foundations; one major office block was actually constructed directly over the alignment during the latter phases of design process. This paper provides an overview of the general site conditions, tunnel design and the technical basis for excavation support and tunnelling decisions. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed. Project construction has now commenced and a brief summary of progress to date is included in this paper; this will be updated for the presentation to be made in Melbourne.

Jan 1, 2008

By P J. Mathew

Quality and process control in the iron ore industry is based on measurements of ore grade from blast holes through to shiploading. Traditionally this has been carried out using conventional sampling, sample preparation and analysis methods, but on-line analysers are now being introduced for monitoring the grade of important process streams. Once a conventional sample has been collected, it can be analysed for a wide range of elements. On the other hand, on-line analysers measure only a few selected elements, but they provide rapid feedback on grade, which is important for effective quality and process control. In both cases, the linkage between mining, processing and final blending operations at the port is crucial to ensuring that product quality is maintained while production targets are met and the life of the resource is maximised.

Jan 1, 1998

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

By Nightingale RJ

A column (50 cm 4) provided with a bell charging mechanism and a rectangular perspex insert was used to investigate the inter-relationship between charging pattern, size analysis and velocity profile for a number of charging methods. It is shown that a strong correspondence exists between size distribution and velocity profile for bell charged ore and coke and that decreased coke volumes cause higher pressure drops and increased central flow in beds with "V" shaped layers. It is also shown that a bell charged mixed burden exhibits greater segregation than when it is bell charged as layers and that when uniformly charged the mixed burden shows least segregation and a virtually flat velocity profile. A relationship is derived for "V" profile charges showing the extent of central segregation with furnace size.

Jan 1, 1975

This paper describes the programing and specification requirements which affected the choice of excavation methods on the Melbourne Underground Rail Loop (M.U.R.L.). The various methods that were chosen are briefly described, and the three most used are compared in more detail. Excavation rates, cycle times and other statistics are compared for full face tunnel boring, full face drill and blast, and heading and bench using a road header excava- ting machine. The length of tunnel excavated is sufficient to enable meaningful statistics to be presented and the significant specifi- cation and geological factors are described to weight the statistics where necessary for purposes of comparison. Average tender prices are given for excavation and primary support to indicate the reimbursement sought by contractors to carry out this type of tunnelling.

Jan 1, 1981

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

Weinberg, born and educated in Germany, worked in'the American West for 10 years as a mining engineer and metallurgist. He was the first head of the Queensland Smelting Co. and from 1889 through 1915 was a prominent mining figure in Queensland. He was a competent manager at Aldershot, Dapto, and Chillagoe, but always lacked huge ore deposits for his smelters.

Jan 1, 1985

Following the `Poseidon boom' of the early-1970s, there was pressure for development of a national body of company law and for the introduction and development of legislation to regulate the securities industry, including the Stock Exchange, trading in securities and securities dealers and advisers.After 20 years, the Corporations Law emerged in effect as Commonwealth legislation implemented automatically by the States.

Jan 1, 1997

By Tilyard P. A

Recent exploration has established depos its of nickel sulphide in several areas of Western Australia. To assist in their develop- ment Amdel has investigated the beneficiation of many samples from these deposits and has estab- lished flowsheets for the recovery of nickel values by flotation. Metallurgical data are presented for the samples according to four factors which were encountered in their respective treatments.

Jan 1, 1973

The different electrowinning cells presently developed for recovery of gold from CIP eluates are compared and contrasted. The efficiency of operation for each cell is,discussed in terms of the electrochemistry of (a) gold deposition, and (b) packed bed electrodes. The advantages and problems associated with each cell design are presented and recommendations are made as to the best method of gold recovery.

Jan 1, 1982

Selective leach analytical techniques applied to surface geochemical samples in the search for deeply buried mineral resources gained popularity in the late 1990s. Several commercial assay laboratories introduced their own selective leach methods, adding to the few established commercial methods at that time. Many of these laboratories promoted their methods with orientation data showing favorable responses to both precious and base metal mineralisation, concealed beneath extensive thicknesses of overburden. However, many explorationists remain confused about the utility of these geochemical methods. This confusion is due primarily to the lack of objective orientation surveys over significant mineralisation, comparing all commercially available selective leach methods and to the lack of a creditable theory explaining the formation of these selective leach anomalies. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. An orientation survey was designed to fill the first void û an objective survey over significant mineralisation. With the help of 17 mining companies and assay laboratories, an orientation survey was conducted over five significant covered gold deposits in Nevada, USA , representing over ten million ounces of gold. Hopefully the results of this survey will help provide fuel for those working on the second void û a theory to adequately explain the formation of these selective leach anomalies.

Jan 1, 2008

By C Chen, W J. Bruckard, F R. A Jorge

The base metal industry mines and processes hundreds of million tonnes of ore per annum to produce saleable products and large tonnages of waste by-products such as tailings. These ores usually contain less than 1 wt per cent of toxic elements (As, Sb, Bi, Cd, Se, Te, Hg, etc), which are subsequently treated with the other components in the ore during the production of concentrate through to saleable metal products. The deportments of minor elements across the various unit operations of a process flow sheet do not normally receive the attention that the major elements receive. However, these minor elements can have a major influence on the quality of the products as well as an economic and environmental impact. Therefore, a high degree of control over their deportments is a key step in reducing their dispersion in the biosphere. Ongoing work at CSIRO has been examining minor element deportments across unit processes used for smelting and refining and the options for early removal of minor elements, as well as methods for safe disposal of some toxic elements. This paper provides an overview of the R&D activities undertaken at CSIRO to develop tools and methodologies for improved management of minor elements during the processing of sulfide ores.

Jan 1, 2006