Search Documents

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

Ranger Uranium Mines (RUM) operates an open cut located in the Top End of the North- ern Territory. Strict environmental controls govern all operations and the water management requirements have the greatest impact on mine planning. The two main goals of planning are to provide mill feed and to mine sufficient suitable quality waste rock for ongoing con- struction of the tailings dam. Early planning concentrated on staged development of the pit to provide access to as much ore as possible for a given amount of development. All waste was considered to be suitable construction material. Grade control of crusher feed was the main problem in planning, as wide vari- ations occur in ore grade over relatively short distances. Water management for the site ope- rates a no release' system for contaminated waters. Design storage has proven inadequate, and the open cut has been used as the extra storage. As construction of future stages of the tailings dam requires non-mineralised rock materials which meet specific quality criteria, the mine has had to re-examine long term plan- ning and pit development strategies. This has entailed the collection of much data not re- quired under normal mining conditions, such as the assaying of waste drill core. The overall impact on mine planning of the environmental regulations has been to alter the philosophy of earlier planning, making it necessary to create a new strategy for pit development with

Jan 1, 1984

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

By Bruce P, Luyendyk

The South Island of New Zealand comprises a collage of distinct tectonostratigraphic terranes. Some tectonic models predict that these terranes formed on or near the margin of Gondwanaland. However, geologic evidence suggests that some of these terranes may be exotic. Over 400 samples from 30 sites were collected from the Brookstreet terrane within the Takitimu Mountains. The section includes the early Permian Takitimu Group and the late Permian White Hill Intrusive Suite. Over 80% of the rocks show a partial or complete regnetization in the present field due to recent acquistion of VRM. Although some remagnetization of the Takitimu Group occurred during the emplacement of the White Hill Intrusives, both early and late Permian direction have been isolated. These directions indicate a mid-latitude origin for the Brookstreet terrane, and suggest a strong clockwise rotation between early and late Permian time. A published paleomagnetic result from the younger, but related, Murihiku terrane suggests that the Brookstreet terrane was sutured to the margin of Gondwanaland by the late Triassic, or that the Brookstreet and Murihiku are two distinct terranes.

Jan 1, 1987

By Hinton A. T

Three, and possibly four, distinct types of quartz-vein associated gold mineralisation are recognised in New Zealand. They are: epithermal, schist-hosted, metagreywacke-hosted and metamorphic core complex associated types. Each has a unique geological environment and structural regime which has provided the gold source, scavenging mechanism, emplacing mechanism and geometry. Each has a characteristic suite of associated metals and trace elements. The first three types form economically important gold deposits while the fourth type have been historically worked for gold and base metals. Intense exploration is currently being focussed on all four types.The epithermal type is typified by the extensive vein systems of Martha Hill, Karangahake and Golden Cross and numerous smaller examples. The veins were deposited in a near surface active volcanic environment from deeply circulating hot water. Their structure is tensional, veins are vertical-to sub-vertical and have limited depth. Their geochemistry is identical to that in active felsic hydrothermal centres in the central North Island. Major minerals are gold, pyrite, arsenopyrite, galena, chalcopyrite, sphalerite and argentite.

Jan 1, 1990

By Boswell GB, Mori W, Stevens MR

The Onemana prospect is located on the eastern Coromandel Peninsula, North Island, New Zealand. Systematic exploration involving surface geological mapping, geophysics, rock and soil geochemistry, reverse-circulation and diamond drilling has identified a number of important features of a fossil hydrothermal system at Onemana. This relatively intact gold mineralised system is hosted within a sequence of rhyolitic volcanics and volcaniclastics, overlain by lake sediments, sinters and hydrothermal eruption breccia. The system lies within a graben/half graben bounded by major NE-trending faults which form the approximate boundaries to hydrothermal alteration.

Jan 1, 1995

In the consideration of coal resources in this country one of the most neglected aspects and perhaps one of the most important is that of the geologic controls on coal formation. The composition, properties, thickness and distribution of the coal are all determined by geological factors. The extent and amounts of coal to be found in the South Auckland area have great economic significance, and are in the main considered here. Upheaval of the New Zealand geosyncline during the Rangitata Orogeny produced a system of parallel, north-south trending basement ridges and basins in the South Auckland area. A subtropical climate and relative tectonic stability allowed deep weathering of these mesozoic greywackes in the late Cretaceous and early Tertiary. Such weathering, markedly reduced the landscape relief, and provided vast supplied of very fine detritus for later sedimentation as the Waikato Coal Measures. This coal measure phase marked the beginnings of Tertiary  sedimentation in this region and represented a change from a sub-aerial weathering regime to a fresh water swamp environment.

Jan 1, 1976

Average annual growth in consumption of primary energy in Australia over the past ten years has been 5.5% compared to a world average of 4.1%. Over the next ten years growth rate is expected to increase to 6% per annum due largely to the rapid development in the mineral processing industry. By the end of the 1970's natural gas is expected to supply more than 9% of Australia's, primary energy market. Coal will supply 40% and petroleum products 47%. Nuclear energy will make its appearance but-will only make a small contribution in the period. Australia has adequate reserves of natural gas and coal to supply its needs in the 1970's and beyond. However the newly developed reserves of crude, while supplying 60-70% of requirements-in the initial years; will need regular and sizable additions if they are to .keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated *that new discoveries-will need to approximate. ten times the volume of recoverable reserves found in Australia to date. .

Jan 1, 1970

This paper compares and evaluates the impact of income tax and value-added tax on the decision to explore for minerals or to develop a mine in four countries: Australia, Papua New Guinea, Argentina and Indonesia. Three aspects are considered in depth:- domestic tax rules applicable to mining projects;- taxation of foreign mining investment and foreign providers of expertise;- taxation of project finance (other than equity) from foreign sources.Specific tax issues discussed include tax deductibility of various costs, treatment of tax losses, special tax incentives, comparative treatment of various corporate structures, non-resident withholding taxes, and tax costs of various forms of project finance. The paper also illustrates the comparative impact of income tax on rates of return by means of a simulation of a mining project in each of the four countries. The simulation demonstrates why the highest rate of return may be obtained in Argentina and the lowest in Australia.Relevant features of the income tax systems in each country (at 15 February 1990) are summarized and compared in several tables annexed to the naner.

Jan 1, 1990

The comparatively low winter rainfall, exposure to heavy salt laden coastal winds, and the consequent high evaporation rate, are important considerations in the rehabilitation of the Maslins Beach Sand Pit. The deficit of rainfall over evaporation is assessed at 1085 mm per annum. Such a coastal environment complicates the establishment of plants. The endemic flora found on the Sand Pit environs is mainly low wind-planed shrubs and mat plants. The dunes near the coast support an association dominated by Atriplex cinerea, Spinifex hirsutus, Scirpus nodosus, and Olearia axillaris. The coastal cliffs carry a more diverse vegetation dominated by Beyeria lechenaultii and Eutaxia microphylla. Overburden is used to develop a new landscape to screen operations, batter final faces, and cover rubbish at the nearby Council dump. The early overburden dumps were built with little regard for stability, but the more recent practice of using scrapers has resulted in more stable dumps. The erosion problems created by poor compaction have been controlled by contour banks, diversion drains, bitumen lined run-off drains, and hay mulching.

Jan 1, 1976

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Rais SA

In June, 1986, Freeport Indonesia, Inc., in conjunction with Out- okumpu USA, laboratory tested the Flash flotation concept on Primary ball mill underflow. These laboratory results indicated a possible 10% increase in precious metal recovery and 0.6% increase in copper recov- ery were available over conventional methods. By October of the same year two Outokumpu Skim Air SK-240 units were operational on one mill circuit and were achieving 5 to 10% increased recovery in precious metals with equal copper recovery at one percent higher final concentrate grade. Two more cells were purchased and installed on the remaining grinding circuit in July, 1987. As part of the installation of the Skim Air cells, an existing cluster of six 508mm Krebs cyclones were replaced by four 660mm Krebs cyclones. To reduce high circulating loads, these new cyclones were made horizontal at 45 degrees. This arrangement succeeded in reducing the mill circulat- ing load by 100% and has allowed for a 10% increase in throughput at the same grind.

Jan 1, 1988

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

Many metallurgical beneficiation and primary concentrating processes rely upon discrimination of products from gangue based on particulate density of the different minerals and combinations of minerals in an ore. The basic definition of density is simple, but the apparent density that minerals exhibit when in the environment of commercial densimetric separation processes is more complex and is ill-defined. Measurement of the apparent density displayed by minerals in their separation situation is essential if modelling of plant performance is to be meaningful or when comparison of an existing operation with a æperfectÆ separation constitutes a part of an audit or of a plant control function. Seven methods of dividing ore samples into discreet density fractions are examined and criticised in this paper. The shortcomings, difficulties and potential errors arising from the use of each method are evaluated. Most of the techniques described have been used by the author and generally their faults are understood and the resultant first-hand experience has been used to overcome these faults. A simple new computer-assisted technique for developing meaningful densimetric data is described.

Jan 1, 2004

This paper discusses why Argyle Diamonds adopted thickened tailings disposal in 1985 and how the system was developed over the next seven years. A wide ranging review of the thickened tailings disposal system and the tailings deposit it was producing was carried out during 1992 and 1993. The results of that review led to the abandonment of thickened tailings disposal at Argyle because of serious concerns about the stability of the resultant tailings deposit. The exposure to the risk of liquefaction and an assessment of the consequences if this happened to the thickened tailings deposit are shown. The criteria for selecting the new tailings disposal strategy are then described. The final section of the paper discusses the management strategies that have been put in place. These are designed to: ò reduce the risk posed by the thickened tailings deposit to an acceptable level; ò safely store tailings to the end of mine life; ò produce a land form that can be decommissioned to the satisfaction of Government regulatory bodies.

Jan 1, 1996

One of the most difficult places to ventil ate in any mine is the working face area of an advancing mine heading. With an ever changing configuration, continual modification and extension to the ventilation system is necess- ary to maintain an adequate supply of fresh air and to control mixing and recirculation. Methane emissions and high dust levels as coal is broken and removed from the face area can produce unhealthy and dangerous conditions if ventilat- ion is not adequately monitored. An understanding of the air flow patterns which develop through use of different face ven- tilation systems can be reached by undertaking underground measurements or through observations using physical models. Tests undertaken by the author to determine the adequacy of different system-configurations are discussed together with approaches adopted by others working in the United States. Various new methods have been proposed for improving face ventilation beyond that sustained using conventional brattice curtain or tubing systems. The adequacy of some advances adopted by mining companies to improve ventilation while maintaining output efficiency is discussed.

Jan 1, 1983

In the last eight years inclined conveyor haulage systems have established themselves in the mainstream for hard rock underground mine haulage. This leaves the question; what else might be on the horizon for mine haulage and how do we address the process of selecting haulage systems for new mines? This paper considers the identification of viable haulage technologies for underground mines and explores an approach for assessing existing and potential technologies. The example of a large deep mine is considered here. The evaluation of existing haulage systems relies on precedence and the assessment of the system capacity to meet the haulage requirements envisaged for a particular mining project. The assessment of potential technologies for mine haulage relies on the capacity to deliver a viable production-scale system within the timeline envisaged for developing a mining project. The haulage technologies addressed in this paper include: shaft hoisting,conveyor haulage,truck haulage,vertical conveyors, andhydraulic hoisting. This paper does not consider rail haulage out of a mine. This is simply because Australian topography typically has insufficient relief to bring them into consideration. However, rail haulage is a widely used and effective haulage solution in situations where significant topographical relief is present. The assessment of haulage system capability focuses on the following fundamental questions: How reliable are they? What is the degree of technical risk in a business context?What levels of flexibility do they offer?How capital effective are they? What returns are indicated by the balance of capital and operating cost estimates?

Jan 1, 2008

The evolution of mineral sand mine rehab ilitation techniques have been techniqually based. Research and investigations have been carried out by government authorities, mining companies and academic institutions. Protection of the physical and biological environments is a vital part of any mine oper- ation. The Mineral Sands Mining Industry in New South Wales is successfully working within the State's environmental framework and is meeting; community requirements and expectations concerned with the environment and mine rehab- ilitation. Keywords: Environment, mineral sands mining, mine rehabilitation, revegetation.

Jan 1, 1986

By Cusack BL

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. This resulted in a deterioration in metallurgical performance with increased loss of lead and zinc to residues at each concentrator. Investigations to determine the cause of the problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical Deterioration.

Jan 1, 1970