Search Documents

Trucks are the primary means of bulk material transport in Open Pit hard rock mines worldwide. They are considered to be the most- flexible system available. The large number of trucks used in some mines provides flexibility. Spare units allow for the reduced availability of the single units. Trucks have however very poor energy efficiency. Only 40% of the consumed energy is for transport of the payload, the remaining energy is required to move the dead load of the trucks. With the increase in cost, pressure, mine operators are now looking for alternative methods to make their operation more economical. Energy conservation and increasing haulage distances and uphill haulage are major factors in many well established operations. New methods have already proven themselves as more economical alternatives. Belt conveyors are an alternative means of transport with much higher energy efficiency. They use up to 80% of the consumed energy for transportation of the payload. Energy costs for conveyors are 30% of the energy costs for trucks on level transport and as little as 15% for elevating payloads. Belt conveyors require much fear spare parts and wear components than trucks. A factor of one to two times applies for level transport and ten to twenty times for uphill transport.

Jan 1, 1986

It is no longer possible to establish a quarry on the most convenient hill then abandon the site, leaving a scar if the stone or sand in the deposit is found to be unsatisfactory. Before approval is given to operate a new quarry, the relevant authorities require a detailed plan of operations from commencement to final rehabilitation. To prepare this plan, a thorough know- ledge of the quality and size of the deposit is required. To obtain this information, the industry must use the most modern techniques available. Many examples can be given showing problems which have affected the smooth operation of a quarry for many years because the initial exploration was poorly carried out. The factors which must-be considered when exploring a deposit are detailed in this Paper.

Jan 1, 1979

By K Guilfoyle

AngloGold Ashanti Australia Ltd operates an underground mine below a large open pit at the Sunrise Dam Gold Mine near Laverton in Western Australia. Operations are based on an extensive mineralised zone which has very complex geometry, has a high ‘nugget effect’, and is difficult to interpret and model. Initial underground ore was produced from relatively narrow orebodies dipping from 15º - 70º. Open stopes aimed to selectively extract high-grade ore, using methods including jumbo stripping and longhole drilling and blasting. The complex geology makes it difficult to accurately locate development and stopes in the positions required for profitable production. In narrow stopes, rock mass damage and overbreak dilute ore grades and increase the cost per ounce of gold poured. In flat orebodies, several different techniques have been used to recover blasted ore but overall productivity is low. Thus selective mining can also be slow, costly and recovers only a portion of the available mineral resources. Large longhole open stopes with cemented paste backfill are used to extract multiple zones of mineralisation from the Cosmo and GQ orebodies. Bulk emulsion explosives and electronic detonators are used in all large stope blasts to reduce the risk of misfires and to accurately control blasthole initiation sequences and delay timing. Larger stopes improve productivity and significantly reduce direct mining costs, enabling the use of lower economic cut-off grades which increase the overall recovery of mineral resources. This paper reviews the evolution of open stoping at Sunrise Dam, the various mining methods and drilling and blasting practices used, the results achieved, and the lessons learned.

Nov 8, 2011

By M Grigorescu, S Crimp, J H. Hodgkinson, P Kokic, W Jin

Mines are typically located in remote, inhospitable locations and movement of materials between site, processor and port are often at risk from extreme weather events. Mining companies have recorded multiple supply chain, production and logistics delays caused by climatic events. Recent analyses of extreme temperature and rainfall events (90th and 99th percentile values) for 1960 to 1985 and 1986 highlighted regionalised increases in the frequency and intensity of extremes. The trajectory of this change is likely to be maintained (IPCC, 2014) in regions where increases have occurred historically, suggesting that some parts of the industry may be faced with management challenges beyond current experience (Hodgkinson et al, 2010; Loechel, Hodgkinson and Moffat, 2012). Reliance on historical data to plan for extremes (such as scheduling production downtime to reduce impact) will become increasingly ineffective as the data become less representative of future conditions. Importantly, mine site remediation and closure management need to consider the future climate to ensure rehabilitation is sustainable under changing conditions.Vulnerability assessments and risk-reducing adaptation will become more common as the industry reaches to secure both a mine’s longevity and the industry’s reputation as shareholders and clients become less tolerant of repeated or prolonged interruptions (Hodgkinson, Hobday and Pinkard, 2014). Climate-resilient new mines may be planned using site planning tools combined with knowledge of future climate scenarios. Scenario tools are valuable for developing a gated risk management approach to reducing climate-risk during a mine’s life, through to the rehabilitation process and for managing care and maintenance or closed mines.CITATION:Hodgkinson, J H, Crimp, S, Jin, W, Kokic, P and Grigorescu, M, 2016. Life-of-mine planning tools for a changing climate – intuitive, interrogative, iterative, in Proceedings Life-of-Mine 2016 Conference, pp 71–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The applicability of Bieniawski and Hoek-Brown empirical strength criteria has been assessed for different groups of coal and various types of intact rocks by using a vast number of published triaxial test data from various places. Analysis of individual data sets revealed that the traditional forms of the criteria do not have a perfect agreement with the data. A strong negative correlation has been observed between B in Bieniawski's criterion and m in Hoek and Brown's criterion with uniaxial compressive strength of materials. Both criteria have been modified and empirical relationships have been introduced for coal as follows:m = 62.903 - 34.213 (log pc) 0.9772B = 10.152 - 4.709 (log pc )0.8889Similar relationships have been developed for different rock types as well.A comparison between the applicability of each of the above approaches with the conventional criteria reveals a very significant advantage for new approaches and a supremacy for the Bieniawski criterion in all cases particularly in the case of coal.The modified Bieniawski criterion fits coal as well as different types of rocks with excellent accuracy.The modified Hoek-Brown criterion gives a good result for rocks but does not fit coal data quite well. In other words, Hoek-Brown criterion is not an suitable one for coal.

Jan 1, 1998

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

It is no longer adequate when starting a new mine to simply select the best equipment. Today's competitive international commodity markets demand superior efficiency which requires systematic involvement of people in continual improvement of production and commercial processes. True Total Quality of Management (True TQM) principles provide an operating philosophy for maximising productivity and minimising unit costs of output. The presentation will show the practical and successful use of these principles. This paper will introduce the case study and provide background material on True TQM.

Jan 1, 1995

The implementation, during recent years, of the concept of distributing chilled water to improve cooling at the working faces represents a very important innovation for the mining world. In a logical extension to that concept it has been recognized that distribution of the cooling water at high pressure would provide a potential source of energy for driving water powered hydraulic machinery such as rockdrills, water jets for moving rock, and support props, in the workings. With this in mind, the Research Organization of the Chamber of Mines of South Africa is pursuing the development of such a dual system that will provide cooling in a deep mine and, at the same time, drive hydraulic machinery. A comprehensive design of such a system has been completed and has shown the concept to be entirely feasible technically using technologies currently available. A pilot system is working in a mine shaft 2000 m deep giving a pressure of 20 MPa at the bottom of the shaft and distributing the cold water into the workings at a pressure of 17 MPa. The system shows considerable potential for improving existing mining methods and will open the way for the development of new mining methods for deep mining operations.

Jan 1, 1986

The aim of all modelling is to replicate geological reality as closely as possible using available data. This paper is aimed at one end of the spectrum, where very limited data is combined with intuitive geological ideas to synthesise models for either target definition or for determining minimum viable mining scenarios. Interactive 3D modelling allows a satisfactory hypothetical geometry of surfaces to be assembled, and provides a fast quantitative method for generating targets. As data flows from exploration, an evolving geological model assists with the progressive evaluation of a prospect. Two case histories are described where this approach has been used successfully, the Mosquito Hill Prospect in Queensland and the Longwood Ranges Platinum Prospect in New Zealand. The possibility is also discussed of hypothetically modelling an orebody which has yet to be discovered. The proper description of an orebody is the foundation upon which all mine design and planning is undertaken. The volumetric accuracy of the model is crucial in valuing an orebody. Geologists must form a geometry which matches the conceptual view of the ore occurrence and ensure that they understand how the computer system used calculates volumes. If the underlying assumptions inherent in the method conflict in any way with the conceptual model visualised for the ore occurrence, then that method must not be used.

Jan 1, 1995

By J Jones, J Blunt

"The requirement for environmental approvals and associated environmental impact assessments (EIAs) is now commonly regarded as a key milestone and body of work during project development. EIAs can be undertaken at various phases during project development, generally either:\ during the scoping or prefeasibility studies, where limited project information is available and the mitigation and management measures of the EIA become a set of criteria and commitments that control project design during the feasibility study, as an iterative approach whereby mitigation and management measures are developed through an integrated process with the engineering team, and measures are included in the feasibility study cost model following the feasibility study, where detailed project design information is available, the cost model is complete, and the EIA is an assessment of a fixed project with limited opportunities for mitigation and management measures to be integrated into engineering design. This paper investigates the advantages of integrating EIA into life-of-mine planning during the feasibility study phase, using the Tampakan Copper-Gold Project (the Project) as a case study. The Tampakan Project is located in the Philippines on the southern island of Mindanao. The Project involves the proposed development of three main areas of infrastructure:a large-scale, open pit copper-gold mine and associated mine site infrastructure (including tailings and mine waste storages, fresh water dam, concentrator, etc) a power station, port and filter plant (PPFP), located approximately 60 km from the mine a pipeline and transmission line linking the mine and PPFP sites.Examples of engineering measures developed through an iterative process to mitigate and manage predicted environmental and social impacts include design of water management infrastructure, modification of the disturbance footprint (eg roads realigned to avoid critical habitat) and realignment of project infrastructure to minimise impacted water catchments.CITATION:Blunt, J and Jones, J, 2012. Integrating environmental impact assessment into life-of-mine planning, in Proceedings Life-of-Mine 2012 , pp 143-152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Aspinall T. O

Draglines have found wide application in strip mining coal seams down to 60m depth. A research Project funded through NERDDC has been underway during the past two years investigating the application of large draglines loading overburden into hoppers feeding into conveyor systems or off-highway trucks. This paper presents the preliminary results of these investigations and covers overburden characteristics, bucket spotting con- trol, bucket design, conceptual hopper systems, system application at representative mine sites, and broad process comparison. The studies have initiated new concepts in the extended use of draglines at deeper strip- ping depths. Alternate arrangements for dragline bucket rigging and bucket control aspects of dragline stripping operations offer productivity improvements. Extended use of existing draglines includes, draglines dumping into hoppers which feed large trucks or conveyors, trigger dump buckets rigging arrangements, and rear dump dragline buckets with integral grizzly bars. The paper details these suggestions, and points to specific areas where the most productive applied research is anticipated. Mine planning considerations detail the factors involved in selecting dragline bench heights in association with hopper operations.

Jan 1, 1989

By L C. Thompson

Biomineralisation is the process by which microorganisms mediate and catalyse inorganic reactions so as to form new mineral assemblages. The goal of biomineralisation as a remediation tool is to control microbial processes and their environment so as to sequester and immobilise specific toxic metals within exceptionally strong bonds of neo-formed mineral assemblages. In this way, the bound metals are no longer mobile within a geological time-scale. Applied biomineralisation uses microorganisms, which are isolated from a metal waste environment and are selected for their ability to rapidly catalyse neo-mineral development from dissolved or leachable metals. A typical waste environment will contain microbes that contribute to the mobilisation of metal contaminants as well as microbes that possess the potential for remineralising available metals. Selection and augmenting the correct combination of bacteria and eliminating the competing mineral degrading reactions are the key to applying biomineralisation as an in situ remediation process. Applied biomineralisation harnesses the microbesÆ ability to stabilise toxic soluble metals into non-mobile mineralassemblages. This paper will discuss and demonstrate the biomineralisation process through several case studies including the Summitville mine site in Colorado, the McCoy-Cove mine in Nevada, the Argonaut mine in California, and an historic lead site in Crooksville, Ohio.

Jan 1, 2004

Water is becoming an increasingly valuable commodity in Australia and the mining community is finding itself competing with pastoralists, domestic consumers and industry for access to what is an essential but finite resource. This paper will provide an overview of various legislative regimes in Australia governing water resources, and will review some of the fundamental issues which should be considered by mining companies when contracting with other parties for the supply of water. The paper will focus on mechanisms to secure access to water for mining purposes, and will deal with the following issues: Grants of water entitlements under legislation û (navigating the legislative requirements necessary to facilitate the taking and use of water for mining activities) The paper will focus on the key legislative requirements for securing access to water in Queensland, Western Australia, New South Wales, Victoria, South Australia, Tasmania and the Northern Territory, and will examine: compliance with regulatory processes for securing water entitlements through the grant of water allocations, licences and permits, etc; and dealings with water entitlements (ie statutory mechanisms for transferring water entitlements on a temporary or permanent basis). Securing access to water under water entitlements through contractual means. The paper will also review of some of the fundamental issues which should be considered by mining companies when contracting with holders of water entitlements for the supply of water from both groundwater and surface water sources. These issues include (inter alia): securing appropriate rights to take and use water in compliance with relevant legislation, the necessity to protect the validity of underlying water entitlements, ensuring the security of supply for the contract term, access rights affecting water entitlements and other important issues relating to the security of water entitlements for miners.

Jan 1, 2003

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

By A L. Hemphill

Conventional models, based on pulp kinetics, were regressed directly to steady-state data from a nine-stage platinum flotation plant, to provide a basis for optimisation studies. æFroth factorsÆ were used to characterise the froth in each stage and a ædepressant factorÆ was used for gangue minerals, to account for addition of depressant to the cleaners. These factors improved the fit, but differences between plant and model of up to 50 per cent were still present in a number of streams in the cleaning circuit. A new model was developed, which incorporated two rate constants for the recycle of particles from the froth. These parameters provided a workable approximation of the distribution of probabilities of particles being recycled in plant cells, depending upon where particles appeared at the surface. The feed streams were characterised by two pulp kinetic parameters and the above recycle parameters, for all minerals and all stages. The fit to the data was improved very significantly, when compared to the use of conventional pulp-based models with several pulp rate parameters. This relatively simple model did not require additional data from batch tests and it was suitable for plant simulations.Simulations of various strategies for plant operation were tested, allowing the simulator to vary the concentrate flows from all or some of the stages, in order to maximise platinum recovery. The simulator was imbedded in an automatic optimiser and constraints on chrome content or mass flow of final concentrate were used. The simulations of the existing circuits demonstrated that an improvement in recovery, (for a constant concentrate mass) of about 0.5 per cent was possible, by optimising all concentrate flows. A significant reduction in the flow of scavenger concentrate and an increase in the recycle flows in the cleaners were noted. The results of simulations of various changes to the circuit configuration are also discussed. An increase in recovery of 1.4 per cent (for constant concentrate mass) has been achieved in recent simulations, through circuit changes. However, it was necessary to keep the mass pull of concentrate, per unit area, within typical limits.

Jan 1, 2005

By D A. Williams, J C. J Boshoff

The properties of tailings that emanate from laterite nickel processing plants are significantly different to most other mine tailings. They typically comprise a mixture of fine materials that are made up of altered clays, chemical residues and salts. Neutralisation processes that are undertaken prior to tailings discharge result in a high proportion of gypsum in the tailings. The salinity of the pore fluid is commonly higher than 140 g/L of salts, dominated by magnesium sulfate. Hydraulically-placed tailings that undergo solar evaporation typically reach dry densities of less than 1 t/m3 of insoluble solids. In situ water contents after many months of drying may be as high as 80 per cent, and peak undrained shear strengths are unlikely to be greater than 20 kPa.This type of material is not conducive to upstream raising, from both a practicality and overall slope stability perspective. Even at rates of rise of less than 1 m/a, it is difficult to effect upstream raising on unaltered laterite nickel tailings. However, the authors have successfully designed and implemented upstream-raised laterite nickel tailings storage facilities. The upstream raises have been formed from both imported natural materials and air-dried and compacted tailings borrowed from the tailings beaches.Drying and associated strength gain has been achieved through various means of mechanical intervention, repeatedly exposing a zone of tailings to the atmosphere for evaporation. Field trials have been undertaken to optimise the approach, and the findings from the trials have been implemented in practice to allow stable upstream raises to be constructed. The cost savings and reduced environmental impact compared to high-volume downstream raises have been significant.CITATION:Williams, D A and Boshoff, J C J, 2015. Upstream raising of laterite nickel tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By C Fenton

The mining industry is a relatively minor user of water, which has historically been largely soured from private schemes. Frequently mines are often located in areas with limited available water resources. Water reform is increasingly affecting access to water for new mining projects and mining companies are being required to consider the value of water and the implications of reliability in their planning. This paper seeks to briefly review the water reform process in Australia and how it is affecting the mining industry with reference to some recent project experience.

Jan 1, 2003

By B Goebel, G Baker

The Australian Magnesium Corporation Limited (AMC) is constructing the worldÆs largest magnesium metal plant at Stanwell, 24 km west of Rockhampton in Central Queensland. The $1.3 billion, 97 000 tonne per year plant is scheduled to commence production in mid-2004. It will produce magnesium from magnesite using the innovative, locally developed AM Process Technology which enables magnesium to be produced at internationally competitive costs. The technology will enable the plant to have the lowest environmental impact of all the available magnesium production processes. The project will meet current world-best-practice environmental and emission standards while on a life cycle analysis, magnesium produced by the Stanwell plant will result in net reduction in global greenhouse gas emissions. Magnesium is the lightest of the structural metals. Its high strength to weight ratio and ease of casting and machinability makes it particularly suitable for the manufacture of light weight automotive components. Reducing the weight of motor vehicles through the use of light weight materials such as magnesium is the current primary means adopted by the automobile manufacturing industry to improve motor vehicle fuel efficiency and the lowering of emissions of greenhouse gases. The Australian Magnesium or AM process has been developed over the past decade by AMC in conjunction with the CSIRO to produce magnesium from magnesite mined at AMCÆs Kunwarara deposit. Over $200 million has been spent developing the AM process, designing, building and operating a demonstration plant at Gladstone and to complete an environmental impact statement and receive environmental approvals as well as funding for the commercial Stanwell Project. The paper outlines the development of the AM process technology, the operations of the Gladstone demonstration plant confirming the process technology, its operating costs and environmental performance. The paper covers the particular attention that was given to minimising the production of CHCÆs, the development of new cover gases for molten magnesium, the minimising of emissions of greenhouse gases and the life cycle analysis of magnesium as a replacement for steel and heavier metals in motor vehicles which confirmed its use resulted in a net reduction in global greenhouse gas emissions. The project received both Commonwealth and Queensland Government environmental approvals by August 2000.

Jan 1, 2002

As modern techniques of Petroleum Exploration and Development are rela-tively new in Australia,2 the alien terms "Mud Logging" and "Core Analysis" will bear explanation. Mud Logging and Core Analysis are two of the Petroleum. Industryts most useful "tools" in the successful search for, and development of, commercial oil and gas deposits. Modern Mud Logging could be more accu-xately termed "Drill Cuttings and Mud Gas Analysis". Presently, mud-logging has its greatest application in exploratory wells where subsurface geologic control is at a-minimum.

Jan 1, 1962

By C van Wyk, I Reeves, J Webber, G B. Gnoinski

The minerals industry has been given an opportunity to grow and continue to advance again in an environment where there is the potential to reap big rewards for efficiency improvements due to buoyant metal prices and the growing demand of markets in Asia. Improving efficiency may also provide a better return compared to risks of expansions and bringing new projects online due to limited human and financial capital.An opportunity for improvement presents itself in the area of mine-mill reconciliation, which entails the quantification of the variance between measurement points along the mining value chain. Reconciliation factors are calculated from the variance between respective sections within the mining sequence. These factors are commonly used as key performance indicators to provide a check on the performance of the operations. Over parts of the mining value chain, there is a fair understanding of the reconciliation between the Resource and Reserve estimates and the measured metallurgical plant inputs and product outputs through understanding of the mine-mill interface. The quality of reconciliation data gathered across the mine and plant is generally not well established due to practices employed in generating the data. The reconciliation variances are often a function of data accuracy and quality used in the comparison. In general, the sources and magnitude of measurement and sampling errors and their impact on reconciliation are not that well understood. Examples of the current practices of mass measurement, sampling, sample preparation, chemical analysis and quality assurance for broken ore and across the metallurgical process stream are considered. Guidelines are given for those reconciliation elements that are identified as requiring a high degree of confidence for Mineral Resource/Reserve and metal accounting reporting. These guidelines are presented and practices are demonstrated to improve mine to mill reconciliation and support increased resource to product efficiency and value.CITATION:Gnoinski, G B, van Wyk, C, Webber, J and Reeves, I, 2012. Guidelines and practical applications for continuous improvement in mine to mill reconciliation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 309-316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012