Search Documents

The non-metallic minerals, excluding the construc- tions and fuel materials have for long been the "poor relations" of the Mining Industry of New South Wales. The State is self-sufficient in only a few of the industrial minerals and is almost completely lacking in any of the essential fertilizers. The deficiencies must be met by imports from overseas and interstate and in fact New South Wales imports some quantity of every one of the non-metallics. For the year 1967 the value of non-metallic mineral production amounted to only $9,390,000 or less than 3.5% of the States total of $275,900,000 for all classes of mining and quarrying. In roughly the same period, the 1967-68 financial year, New South Wales imported non- metallic materials, valued at well in excess of $22,000,000 from overseas and over $2,000,000 from interstate sources.

Jan 1, 1969

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

Over the last decade mineral exploration in New South Wales has increased markedly. This is due to various factors including the influx of overseas companies an. capital, increase and stabilization of metal prices and improvements in exploration techniques. The initiation of full-scale petroleum exploration and recent discoveries of large mineral deposits in the west, north-west and north of Australia has increased overseas capital, and brought scientists and technicians into the country. Naturally there has been an overflow into New South Wales, which is less attractive as an area for new and large-scale discoveries. In some fields, rise in metal prices and price stabilization has largely contributed to the intensif- ication of exploration. Increased tin production in New South Wales since 1963 is a direct result of price rise and stabilization, and rise in the price of silver has revived an interest in silver prospecting in recent Years,

Jan 1, 1969

A resource rent taxation scheme is based on the concept of taxing the rent or surplus profit generated from primary industry activity. Rent has been defined as profits that remain after deduction of company income which corresponds to the minimum return necessary to attract private investment to a new project.Rent taxation schemes on the mining industry within the Australasian region have been examined and widely discussed during the decades of the 1970s and 1980s. Forms of resource rent taxation schemes have been imposed on Papua New Guinea mining, some sectors of Australian petroleum, the Roxby Downs venture and are being discussed for the New South Wales coal industry. While no introduced applications have been pure rent taxation schemes, the concept has generally come to encompass arrangements which tax rent at a partial rate which may or may not vary with the level of profitability or return.An examination is made of a number of the more recent schemes. Aspects which should be considered in implementation of new forms of this taxation are discussed. It is concluded that there is an increased acceptance for this form of taxation on the Australian mining industry.

Jan 1, 1990

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

By Gibson G, Jaques L

The Broken Hill Exploration Initiative (BHEI) is a collaborative venture between the Australian Geological Survey Organisation (AGSO), Mines and Energy South Australia (MESA) and the New South Wales Department of Mineral Resources (NSWDMR) to provide a new generation of geoscientific information to promote and enhance the exploration for, and discovery of, new deposits in the Broken Hill region. The area under investigation (Figure 1) exceeds 150 000 square kilometres on either side of the NSW-SA border and is centred on the city of Broken Hill. N.T. I I OL n. WA 8A I Maw. AC,7 !ii oFCU vlc~ ~T. Fia I - Nlap showing the 150 000 square kilometre regwa,. i.i lcr investigation by the Broken HiII Exploration Initiauvr highlighted on the map of Australia. A major impediment to the exploration for, and to the understanding of, the genesis of the world-class Broken Hill Pb-Ag-Zn deposit is the structural and metamorphic complexit\ of the region. Important objectives of the BHEI are therefore: I. the definition of the three-dimensional structure of the province, 2. the deformation history, and 3. the stratigraphic and age relationships of the rock units. Early discussions between the BHEI partners and industry scientists revealed that new geophysical surveys would be a key requirement to help advance the understanding of the province, especially a contiguous high resolution airborne geophysical dataset covering both outcrop and areas of shallow surficial cover. The purpose of this paper is to draw attention to the new high resolution airborne geophysical data and to discuss their interpretation and potential for enhancing the knowledge of the Willyama Supergroup geology.

Jan 1, 1997

This paper has been prepared to challenge the thinking of new leaders entering the mining industry in two areas. First, what is the worldÆs perception of mining and what does this mean to those entering the industry? Second, what is the future of learning in the mining industry and how can the industry attract and retain the best people?Then in closing, how can mining companies turn these challenges into opportunities and specifically how is BHP Billiton meeting these challenges.

Jan 1, 2004

By Mackenzie JMW, Virnig MJ, Kotze MH

A new range of solid and liquid ion exchange extractants for gold based on the guanidine functionality is described. These extractants have pH versus gold extraction isotherms which lie between those of the conventional weak base and strong base resins which have previously been studied as aurocyanide extractants. Possible applications of these new extractants in gold recovery are discussed.

Jan 1, 1993

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By D Mee

The Western Mining site at Olympic Dam, near the community of Roxby Downs in South Australia is one of the largest orebodies of its type in the world. It contains known reserves of over 10.6 M tonne of copper, with economic secondary metals including uranium, silver and gold. In 1996, an expansion project was commenced to increase mine production approximately threefold, to produce 200 000 tonnes pa of copper, 4600 kg pa of uranium oxide, 3600 kg pa of gold and 50 000 kg pa of silver. This expansion included both underground mining and surface processing investment. Because of the scale of operations, it was decided that ore should be transported underground by a railway system. In July 1997, ALSTOM Automation and Control Limited (then Cegelec Australia Limited), was awarded the contract to deliver a control system to manage and automate the rail haulage system for Western MiningÆs Olympic Dam Mine, as part of this major upgrade and extension project. This paper explains the overall design and the approach taken to implement route selection, route locking, train interlocking and track topology using normal industrial control equipment such as Programmable Logic Controllers. Included is a discussion of how this automation has improved the productivity of the haulage system by more than 15 per cent.

Jan 1, 2000

By Prince R. G H, Guerney P. J, Frew J. A, Vanderkruk C. R, Wanigasekara-Mohoti D. K

This computer-aided design system for mineral processing flowsheets which are based on froth flotation, size reduction and classification combines an expert system for generating flowsheet structures with numerical models for the physical processes and the economics. Design decisions, such as specification, size and placing of process units and the destination of recycle streams, are based on clear technical and economic criteria. These decisions are controlled by user-set parameters, which allow the incorporation of industry experience and preferences and the generation of sets of good designs, from which choices may be made by further criteria, such as controllability. Liberation is now fully modelled and the early results from this extension continue to suggest potential substantial increases in added value over conventional approaches.

Jan 1, 1997

By P Dean, M Elmouttie

Radar monitors are now widely used in surface mining for monitoring slope deformations and predicting failure events. Their introduction has facilitated better management of risk associated with slope failure during mining and therefore protection of personnel and equipment. However, a wellrecognised problem is that radar monitors only measure deformation directed towards the detector (line-of-sight bias). This bias can lead to misinterpretation of deformation size, rate and failure mechanism, and therefore miscalculation of failure volume, which can significantly impact safety and productivity. This paper presents recently completed research and field trials into the feasibility of using low cost vision systems to mitigate this issue. It has been demonstrated that by integrating a computer vision system with an existing slope monitor, high precision tracking of features in the field of view can be performed. Combined with assumptions on the deformation characteristics, the true 3D deformation vector can be estimated. The applicability of using this technique for monitoring iron ore mine slopes is discussed.

Nov 8, 2021

Platinum Group metals have been known in New Zealand since the 1880's but not produced on a large scale. They have been neglected because their value was not appreciated rela- tive to gold and their value was often very low, reflecting demand, and because recovery was difficult compared with recovery of gold. With the rising price of most Platinum Group metals and the perfection of gravity and flota- tion recovery methods, recovery of platinum along with gold from alluvial deposits is more attractive. Platinum Group metals are known in several different environments in New Zealand, ranging from alluvial placer deposits to layered basic to ultrabasic intrusions and quartz veins. None of the known occurrences have been ade- quately prospected and there is a real possibi- lity of future discovery of important deposits. Several New Zealand based and at least two offshore resource companies are currently involved in exploration, prospecting or mining for Platinum Group metals in New Zealand.

Jan 1, 1987

Papua New Guinea is geologically prospective for large, medium and small mineral discoveries. All profitable developments to date have been very large mines but for every large mine there should be many small mines which could be developed under appropriate circumstances.The Papua New Guinea Government should, with appropriate changes to fiscal, legislative and policy regimes, create a favourable exploration envir-onment to encourage a major increase in exploration by small exploration companies and subsequent discoveries and mine development.

Jan 1, 1994

The importance of good winding rope practice is stressed. Details of the ropes used for various duties in the four shafts of The Zinc Corporation, Limited (ZC) and New Broken Hill Consolidated Limited (NBHC) are given. Inspection, testing (including non destructive methods), maintenance and rope discard criteria are discussed. There are sane catments about rope installation methods and an appendix is included which outlines the appropriate statutory requirements for winding ropes in New South Wales (NSW).

Jan 1, 1983

A viable flow sheet of the sorption-flotation technology for gold recovery from low-grade ores and concentrates using powdered activated carbon modified by organic compounds as the sorbent-bearer has been developed. The powdered activated carbon, with high kinetic ability and sufficient specific area, was selected as the all-purpose gold cyanide complex-bearing sorbent which is active during flotation. To improve carbon adsorption capacity and to provide the required floatability its porous structure was filled with a quaternary ammonium compound which can extract gold cyanide complexes and render additional flotation properties to the carbon. To optimise the process and to simplify the layout, adsorption and flotation processes were carried out simultaneously in a mechanical flotation cell. The proposed technology was used for extended and pilot-plant tests of sorption-flotation gold recovery from 0.6 g/t Au final tailings and 2.0 g/t Au gravity tailings. The extended tests were carried out on Taseevskaya (Chita Region) flotation tailings, whereas pilot-plant tests were conducted on Kommunarovskaya (Krasnoyarsk Region) gravity tailings passing to cyanidation, followed by processing with filtration technology. Additional gold recovery from Taseevskaya final flotation tailings was 50.8 per cent. Gold recovery from Kommunarovskaya final gravity tailings was 92.5 per cent. Compared to the complete sludge process conventionally used at the plant, gold recovery was increased by 7.5 per cent due to lower gold losses in the liquid phase and conversion of the refractory non-cyanided metal into a carbon concentrate. This paper presents the experimental results of gold adsorption onto powdered activated carbon modified with quaternary ammonium compounds (sorbent-bearer) as well as sorbent-bearer flotation with various collectors from cyanide solutions and pulps.

Jan 1, 2005

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024