Search Documents

By P Warner

Mines are often located in remote areas that are not well served by æstiffÆ power grids. Radial transmission networks, high lightning incidence (eg in South Africa the Witwatersrand experiences seven to ten strikes/km2 per year), low short circuit strengths and diesel generation are not uncommon. All these factors result in the electric power supply to many mines being unusually prone to dips and disturbances. æLegacyÆ winder drives û cyclo converters and dc drives û convert power directly from the supply to the motor, with no intermediate energy storage element. Further, they rely on the supply network for commutation and are therefore sensitive to supply voltage disturbances. There is a high probability that a dc or cyclo mine winder will trip during a supply disturbance, often resulting in lost production time and call-outs for technical staff to reset or even repair equipment. In contrast, a voltage source inverter (VSI) ac drive stores a large quantity of energy (in the dc link capacitors) and is fully self-commutating. Hence, this topology is inherently more immune to supply voltage disturbances. Indeed, vendors of ac VSI mine winders make general statements about the superior performance of their drives during supply disturbances. However, the advantages have apparently not been previously quantified. This paper compares different winder drive topologies and their sensitivity to supply disturbances, considers categories of supply disturbances and quantifies the cost of the effects on the different drive types.

Jan 1, 2005

By T Vizcarra, G Sandoval, C L. Evans

One of the challenges in the development of mineral processing simulators is modelling the liberation characteristics of particles produced by comminution circuits. Understanding the mineral characteristics of these particles is one of the keys to predicting their behaviour in separation circuits. While more fundamental research seeks to model the non-random breakage of ores this work examines whether we can move forward now by using observed characteristics of ores to model the composition of particles generated in comminution processes. Several researchers have noted the similarity of the liberation characteristics for a selected size fraction of particulate material, whether the fraction comes from a coarse material, such as the product from a jaw crusher, or a more finely ground material, such as the product from a ball mill. In most cases these observations were reported as an aside and were not the main focus of the published work. This observed behaviour has the potential to be a useful tool for modelling the particle characteristics in mineral comminution and separation circuits, particularly as we move towards the development of multi-component models. However, before the behaviour can be used widely we need to understand which ore types follow the observed pattern and which do not. The current work examines a range of ores and identifies which exhibit the pattern of similarity of composition for particles in a given size class that has been produced as the result of a variety of breakage conditions. The impact of mineralogy and texture on the evolution of liberation characteristics for both valuable and gangue minerals is discussed.

Jan 1, 2008

By Cornell J. B

Scaling in Bayer Refineries is a natural consequence of the super-saturated liquors used in the process. The caustic liquor is supersaturated not only with alumina but also silica and calcia at various stages of the process. The basic scaling mechanisms are reviewed and examples of the two basic types, growth and settled scales, are given. Examples include gibbsite scales formed in the precipitators and silica scales formed in heat exchangers. The main factors affecting the rate of growth of growth scales are temperature and supersaturation and are highlighted using a silica scale example. For growth scales chemical cleaning rates can readily be predicted from kinetics and an example for a gibbsite scale is given. For settled scales the growth rate cannot be predicted and the hydrodynamics within the system have most effect. There is no simple method to predict the potential for chemical cleaning of settled scales; some of the relevant issues are discussed, in particular methods to identify the cementing phase in the scale. An example of design considerations for a scaling system, transport of slaked lime, is Given.

Jan 1, 1996

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

The technology of coal preparation, while based on similar processes to those in common useage in the 1950s, has improved significantly over the past 15 years primarily due to advances in process control. This technology at least offers the potential for most coal preparation unit operations to be optimised to a considerable degree. However, to maximise the overall yield of an operation from pit to port, factors often outside of the control of the preparation plant operator have a dominant effect. Specific factors include an in depth knowledge of the feed characteristics of the various sources of coal, the detailed mine scheduling to provide an appropriate blend to the plant, and the interim handling and stockpiling processes between the mine face and the customer.This paper summarises the criteria for optimising the yield for a variety of mining, processing and stockpiling options, based on the principle of operating at constant incremental ash. Pragmatic operating assumptions such as extension of the principle to operating at a constant density for gravity operations will be discussed. A means of optimising the compromise between maintaining specification product ash to the customer and maximising yield by always washing at constant incremental ash, without the benefit of a homogenised feed, will also be Presented.

Jan 1, 1992

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004

Arrow Energy NL has been operating a number of coal seam gas wells in the Darling Downs region of Queensland. At the time of writing this paper, the region is enduring an extended drought period. The local aquifers are depleting and have not been significantly recharged in over a decade. The local communities (both rural and townships) are struggling to obtain water. Currently, coal seam gas (CSG) operators (under licence) draw water from the coal seams as part of the gas production process and the majority of operators choose to evaporate this water, as it is characteristically brackish to saline in quality and as such must be contained. Although the water produced from one CSG operator is not sufficient to drought-proof the greater area of the Darling Downs, there is potential to supply smaller local areas and contribute to the sustainability of these communities. This paper outlines the work completed by Arrow and its local community partners on the Darling Downs to date, and discusses the application of the produced formation water for:stock watering in feedlots, as a feedstock for coal washing, as a potable water supply for Dalby, as an agricultural water supply for cotton farming, and use as a medium for growing salt-water fin fish.

Jan 1, 2006

The Olympic Dam copper-uranium-gold-silver deposit, located 520 km NNW of Adelaide, S.A. was discovered by Western Mining Corporation Ltd in 1975, and is now being developed as a joint venture between WMC (5107o) and the BP Group (4907o). The discovery of this deposit resulted from the application of a conceptual model for the formation of sediment-hosted copper deposits. This model postulated that the oxidation of basaltic rocks could release significant amounts of copper into solution and that, under favourable conditions, these solutions might pass upwards along faults, and the copper be precipitated in reduced- facies sediments higher in the sequence. The Stuart Shelf province was chosen for exploration because geological interpretation suggested the presence of suitable basal- tic source rocks at depth, and favourable host sedimentary rocks in the overlying sequence. The Olympic Dam site was selected for drill-testing because of the presence of coincident gravity and aeromagnetic anomalies suggesting the presence of basalts and/or mineralisation at depth. This site also had a favourable tectonic signature, indicating the presence of deep crustal structures which might have allowed fluid migration.

Jan 1, 1988

By Smith I. W

Australia has, and faces, a growing problem with regard to the ability to meet the demand for liquid fuels from indigenous petroleum resources. The position for natural gas is better but there is no room for complacency. Since the coal resources are relatively extensive, interest in the prospect of producing liquid fuels from coal is in- creasing. The approaches to the production of gaseous and liquid fuels are briefly reviewed and the present status of coal conversion technology is discussed. Many problems remain to be solved and it is estimated (in the USA) that another 8-10 years will be required before any of the processes for liquid fuel production are considered sufficiently efficient and viable to go to a demonstration plant. Coals represent complex feedstocks and the effects of variations in coal properties on oil-from-coal processes are not fully understood. The thermal efficiencies of various coal conversion processes are considered in relation to their impact on coal requirements. The production of Australia's present requirement for liquid fuels by the only commercial process in operation would require a four-fold expansion in the local consumption of coal. Any assessment of the suitability of oil-from-coal processes currently under development overseas for Austra- lian coals and requirements must take heed of the differences in coal properties and motivation. The economic via- bility of processes for producing oil from coal will continue to be uncertain because of the large difference between the World price for crude oil and the actual production cost.

Jan 1, 1975

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

By Ramani R. V

In this paper, a comparative performance evaluation of geostatistical, spectral, and fractal methods is made for short-scale variability prediction. The algorithms compared are: sequential Gaussian simulation method; a random fractal algorithm based on the generalised stochastic subdivision method; and a spectral simulation approach adopted for direct multi-dimensional simulation. The data for this study have been obtained from a mined out coal property. As this property was being mined, a 7315 m by 7315 m (24000 ft by 24000 ft) coal block was extensively sampled at an approximate spacing of 107 m (350 ft) and the 60-ton samples were analysed for sulphur in the 1.50 float gravity fraction. This data set is used here with the three methods to generate the simulated realisations, which are analysed for semivariogram reproduction and for simulation errors. Although all three methods converge to the true semivariogram in an average sense, the coefficient of variation of the average semivariogram for the Fourier integral method is minimum. The realisations generated by the sequential Gaussian method have minimum mean simulation error. The choice of a simulation method based on variability reproduction and simulation errors remains difficult.

Jan 1, 1995

By Manlapig E. V

ABSTRACT- I Results are given for a series of tests in which a 300 mm pilot-scale Jameson cell has been used in copper recleaner flotation, and for the flotation of a lead rougher feed. the results indicate that the production rate of solids, at the same superficial air velocity Jg, is higher than in conventional columns. Thus in the copper recleaner application, the pulling rate reached 14 gm/cm2/min compared with between two and three for an operating column, while in the lead cleaner application the comparable figures were 12 - 14 gm/cm2/min for the Jameson cell vs 8 - 9 gm/cm2/min for a test column. A froth crowder was used to increase the air superficial velocity Jg in the Jameson cell in the copper recleaner, while holding the collection mechanism and pulp feed rates constant. The recovery increased from 50 per cent to over 90 per cent, suggesting that recovery is controlled mainly by the froth conditions, rather than the particle-bubble interactions in the Downcomer.

Jan 1, 1991

By L H. Chapman, I J. Kelso, N H. S Oliver

Utilisation of modern 3D visualisation tools, can improve our ability to correlate between different datasets, and thus to produce more accurate geological models. Here, we present an application of such techniques to the Century Zinc Deposit, northwestern Queensland, Australia. This stratiform orebody is the second largest Zn resource in the world (167.5 Mt at 8.2 per cent Zn, 1.2 per cent Pb, and 33 g/t Ag). It is hosted in the Page Creek Syncline affecting Mesoproterozoic shales and siltstones of the Wide Supersequence of the Isa Superbasin. As in other deposits, (eg McArthur River, Lady Loretta, George Fisher and Dugald River), the mineralised sequence is bound by an important regional structure, the Termite Range Fault, which partly intersects the deposit along its Eastern side. This fault is thought have been active during sedimentation and probably also during mineralisation of the lowest part of the Wide Supersequence. The anastomosing geometry of this fault system and crosscutting relationships with other NE trending structures indicate that it was reactivated several times from Mesoproterozoic to at least late Devonian times (>1000 million years in total); as a result, the ore sequence is subdivided into several fault blocks.Using two different computer modeling packages (GOCAD and 3ds max), we have reconstructed and restored the stratigraphic horizon with the highest Zn content, realised a series of isopach maps for each mine scale stratigraphic unit, plotted the three-dimensional distribution of Zn, Pb, Ag, Fe and SiO2, and have begun to evaluate the degree of correlation between thickness changes and sulphide zoning. With this approach it is possible to better understand the timing of mineralisation from a genetic perspective, because the origins of the orebody are controversial. Three-dimensional reconstruction is a vital tool for identification of syn-sedimentary and post-sedimentary fault activity. In conjunction with sulphide precipitation, these are factors that greatly influence the stratigraphic thickness distribution. Post-sedimentary deformation can be recognised directly by core logging and pit mapping, but the effect of tectonic movements during sedimentation (growth faults in particular), that represents a substantial variable when we attempt to reconstruct basin evolution, is difficult to evaluate without this methodology. The 3D models improve our understanding of the local basin architecture, identifying similar grade characteristics at different structural levels and thus suggesting that much faulting and folding are post-mineralisation events. In addition, we identified several growth faults adjacent to thickened layers, representing two possible sedimentary depocentres. These thicker domains apparently relate to the highest Pb content. If further analysis of rocks, thickness and grade distributions support this preliminary correlation, then a syn-sedimentary model for mineralisation might be applied, and would contrast with the sub-surface model for mineralisation of Broadbent et al (1998).

Jan 1, 2003

By Weatherstone N

Ironstone outcrops on the Savage River were discovered by State Government Surveyor C. P. Sprent in 1877. The limonitic outcrops were initially regarded as the surface expressions of pos- sible tin-bearing lodes, the tin deposits at Mt. Bischoff to the east having been found in 1871. By the turn of the century, shafts, adits and trenches had been developed on the deposits in the unsuccessful quest for gold, silver and base metals. The deposits were first reported as a possible source of iron ore by Tasmania Department of Mines (TDM) geologists in 1919. Modern exploration began in 1956 with the area registering the best magnetic response during an aeromagnetic survey of North- western Tasmania by the Bureau of Mineral Resources (BMR). The area had previously been reserved by TDM in anticipation of the lifting of the iron ore embargo. Reconnaissance Geologi- cal mapping (TDM) and grid-based magnetometer surveys (BMR) indicated that resources of iron-bearing material could approach hundreds of millions of tons. This provided the incentive for two diamond drill holes funded by TDM which demonstrated iron mineralisation in substantial tonnages, suitable grades and, fol

Jan 1, 1988

For an exploration area with a predetermined grid of data points, a construction is given for elementary blocks which subdivide the entire area without omission or overlap, and with the property that each data point is situated at the centre of its corresponding block. The construction has a useful optimal property, and more importantly avoids an error which has been made recently in more than one publication.

Jan 1, 1985

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024

The 5.6 km Canning Tunnel was constructed to improve water supply from Canning Dam to the Perth metropolitan area. The site area is in the Darling Range which is essentially a laterite-capped plateau-remnant underlain by Archaean granitic rocks, intruded by dolerite. Two arrangements were available. After geotechnical investigations which included geological mapping, seismic refraction geo- physics, diamond drilling and mechanical rock testing, a single tunnel was selected in pre- ference to two short tunnels and a connecting pipeline. The tunnel is hydraulically equivalent to a fully lined tunnel 1.83 m in diameter and 5 580 m long. The alignment diverged from a straight line so that the initial upstream section was almost normal to the contours which allowed for minimal support requirements in a weathered zone. Although steel and con- crete lining was needed at both ends, the main section of the tunnel was unlined except for a concrete floor. A sand and rock trap with a capacity of 46 m3 was constructed near the outlet portal to collect debris and sand down to a size of about 2 mm. Portal excavations were in highly to completely weathered rock which extended 56 m into the tunnel at the upstream end, and 18 m at the downstream end. Conventional drilling and blasting were used for tunnel excavation with survey control by laser. Breakage lEngineering Geologist, Mines Department, Perth, W.A.

Jan 1, 1976

By Percival T. J

Precious metal deposits containing fine-grained disseminated or dispersed gold-silver form by reactions between metal-bearing hydrothermal fluids and sedimentary host rocks. Host rock permeability and chemical composition exert a primary influence on the fluid movement necessary for any primary dispersion halos to form around ore bodies, and determine whether a disseminated style orebody itself will even form. Where the mineralized rocks are relatively unfractured the margins of the orebodies exhibit abrupt decreases in gold content, and strong corresponding decreases in the contents of other metals. Primary dispersion patterns of this type are difficult to recognize and commonly are only a few meters (or less) in width. If the host rocks were well shattered and broken before mineralization, remnant amounts of the hydrothermal fluids may be dissipated in fractures lateral to or above the ore zones. This causes geochemical anomalies to form with clays and silt- size silica within the fractures over distances of up to at least 30-50 meters away from the main orebodies. The tendency for large primary dispersion halos not to form around these deposits explains the disappointing results from so many drilling programs where no multi-gram gold-grade material was even found: if large areas and apparent large volumes of rock contain one gram or less gold that likely is the "orebody" and not a halo effect around high grade mineralization.

Jan 1, 1988

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002