Search Documents

By B Harvey

Achieving community and stakeholder endorsement during life-of-mine planning and implementation requires a business-connected approach, as opposed to charitable giving, disconnected offsets and environmental adventurism.CITATION:Harvey, B, 2014. Extractive companies, development and environmental agendas, in Proceedings Life-of-Mine 2014 , pp 19–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

By S M. W Rajaratnam, P Varma, T L. Sletten

Mining employees undertaking shift work are at considerable risk of experiencing sleep disturbances and circadian rhythm disruptions. In the complex, high-risk environment of mining, these sleep and circadian disruptions lead to adverse impacts on employee health, alertness and safety. Evidence-based tools that effectively target improvements in sleep health amongst shift workers are needed. Variability in work hours and individual differences in the response to shift work mean that a ‘one-size-fits-all’ solution is often insufficient in complex work environments. Currently no interventions provide tailored support for shift workers based on their rosters, personal commitments and sleep habits. Existing technologies, such as smartphone applications and watches, allow sleep monitoring, but their strategies are targeted towards night sleepers, which does not translate to shift work contexts. To address this, our team has developed an innovative digital tool that implements biomathematical models to provide automated, personalised sleep and circadian intervention strategies to optimise sleep, alertness and performance during shift work. The tool uses mathematical models of sleep and alertness regulation that provide physiologically optimal times for an individual to sleep when experiencing circadian disruption. This program of work included co-designed development of a world-first app with shift workers and the examination of the preliminary efficacy of the intervention for improving sleep, alertness and performance.

Apr 16, 2024

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By Richards RG

The Australian glass sand industry produces some 2.8 million tonnes per annum of silica sand, of which about 2.0 million tonnes are exported and the rest is for the domestic market. Approximate production rates for each Australian state are listed.The variety of processing methods used in the currently exploited deposits reflects the size, location, and characteristics of the various deposits and the requirement of the end market/s. The industry uses to a large extent equipment developed for the separation of mineral sands, particularly as it applies to low grade heavy mineral deposits, where low cost, high capacity and metallurgically efficient equipment has proved eminently suitable for the production of the low value glass sands.The requirements of the domestic market, as well as those of the present and potential export markets are discussed covering quality requirements, distribution channels and other factors critical to success.

Jan 1, 1990

In recent years, the. art of electric steelmaking has received a great deal of attention, and naturally, much controversy has existed from time to time regarding the relative merits of different practices and tywes of furnaces. Nevertheless, at the present time, the basic principles of the process are reasonably well established, and by far the greatest percentage of electric steel is a product of the basic lined, direct arc type furnace. Ferro alloy manufacture has demanded the development of furnaces having very different characteristics to those used for steel. Some special alloys, however, require conditions of manufacture which are more closely approached in the steel type furnace, and thus the latter has been adapted where necessary for the production of these alloys.One such alloy, low carbon ferro-manganese, is manufactured at Whyalla, South Australia, in a basic-lined, direct arc furnace, which is used alternatively for the production of alloy steels.BRIEF HISTORY OF THE ELECTRIC FURNACEThe principle of melting by electricity was first applied to the melting of iron in 1879 by William von Siemens, whose equipment consisted of a small crucible into which were introduced two carbon electrodes. Very little practical development took place in the next 20 years, although in 1890 a Frenchman named Heroult designed a direct arc furnace for the production of ferro alloys. At the beginning of the 20th century, several types of furnaces were patented for steel melting, the most important of these being the Heroult, using a direct arc, the...

Jan 1, 1951

By B, T Norgate, S Sanetsis, R Davidson

Global cement production accounts for about five per cent of man-made CO2 emissions (WBCSD, 2002). Such operating practices will increasingly be considered unsustainable, unless significant reductions in environmental impact can be realised by the industry.Slag is a high volume waste product from ironmaking, with about 300 kg of slag being produced per ton of iron. Critically, one ton of slag waste, if used as a replacement feedstock for Ordinary Portland cement (OPC), can prevent around one ton of emitted CO2 since no calcining is required. Slag cement blends can also show superior properties compared to OPC, such as lower heats of hydration and higher late strengths, but more development is needed to overcome their low early strengths. Rapid quenching of molten slag is required to produce æhydraulically-activeÆ binder when reacting with OPC; but water quenching can also require between five to ten tons of water per ton of slag at the plant. æDryÆ granulation (atomisation) is emerging as an alternative technology, the resulting solid product does not require drying, and possibilities exist for recovering heat energy from the hot slag.CSIRO Minerals has well-developed skills and equipment in pilot-scale pyrometallurgical treatment, and granulation of molten slag, including traditional wet, and also dry methods. Techno-economic desktop studies can also be used to help quantify factors such as value-adding of treated waste products, potential reductions in CO2 emissions and carbon credits, reductions in water consumption, and the possible decreased energy costs associated with fine grinding of dry slag granulate.The authors will present preliminary results from slag atomisation/dry granulation testwork (0.5 - 2.5 kg scale) and associated modelling studies, conducted using a æsyntheticÆ and industrial ironmaking slag. Outcomes from a techno-economic study on production of cement utilising wet or dry atomised slag granulate will also be discussed in detail.

Jan 1, 2004

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

By F Schoenbrunn, T Laros

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to be successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings impoundment design, underflow pumping, and control system.

Jan 1, 1998

The AusIMM came into being to foster the spread of professional knowledge within its client industry. It has evolved along with the Australian mining industry for more than a century. If the AusIMM is to become the world's premier mining professional body (whether by design, or by default), then draw up a strategic plan to get there. Define your strengths and market them Define the priority areas for professional competence which we most need, Target the groups within Australia who can produce the people, Create an industry peer group to speed technology transfer.

Jan 1, 1994

By L B. Zhou, Q Wang

The present discussion focuses on the developmental directions of eco-restoration of acid mine waste rock dump, by using acid mine waste rock of Shuilong Mountain as an example. Based on the analysis of site factors, the current slope ecological restoration technologies of domestic and international and local practices have been integrated into the eco-restoration of acid mine waste rock in Shuilong Mountain. A set of suitable slope Eco-restoration technologies have been formulated locally for acid mine waste rock of Shuilong Mountain, which include establishing green barrier, implementing ecology buffer zones, selecting suitable plant species and combined seeding and tube-stock planting. It aims to restore the plant ecosystem to a near natural state, in couple with slope stabilisation and soil remediation.CITATION :Wang, Q and Zhou, L B, 2012. Projection of ecological restoration of acid mine waste rock of Shuilong Mountain at Dexing Copper Mine, in Proceedings Life-of-Mine 2012 , pp 305-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

Tasker (1985) has detailed the accepted practices for constructing polygonal blocks of influerrce in the estimation of ore reserves. Further he suggests that users might fall into traps such as omission or overlap when determining the area of influence for each sample point.As an example of these types of errors Tasker (1985) describes under "Coverage ofthe Area" how 25 per cent of the exploration area will not be included in an equiangular triangular grid where hexagonal blocks of influence are used.The introductory suggestion of Tasker (1985) of "incorrect procedure" by Rudenno (1983) (and Armstrong (1983)) reiterated around the Figure 2a of Tasker (1985), is based on the brief description of the polygonal area of influence by Rudenno (1983). That description is not too different from that given by King, McMahon and Bujtor (1982).

Jan 1, 1985

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

The QSL continuous lead smelting process incorporates two basically different pyro- metallurgical operations: roast-reaction, smelting of galena concentrate, followed by carbothermic reduction of some by-product lead oxide slag. Both steps are performed simultaneously in separate compartments of a long horizontal cylindrical reactor, which is lined with fused chrome-magnesite bricks. This converter-type reactor contains a liquid bath consisting of a shallow layer of lead bullion with a superimposed layer of slag, the lead content of which is gradually reduced from about 50% to discardible levels. Metal relative to slag, and slag relative to the gas phase are in continuous countercurrent motion. A lead well is arranged at the flue end of the reactor, and an overflow tap for slag at the opposite end. Tonnage oxygen for oxidation and smelting of the charge, and sub- stoichiometric mixtures of pulverized coal and oxygen for reduction and heating of the slag, are directly blown into the bath using fluid-protected Savard-Lee injectors. High gas-liquid momentum transfer ensures intensive local mixing, and enables rapid mass and heat transfer.

Jan 1, 1984

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007