Search Documents

Both the miner and the Regional Water Board have legal obligations to ensure that all discharges of water from a mine site are free of harmful wastes, and that proper authorisation is obtained to abstract, divert, or discharge water. This requires long-term planning of water management for the whole of the mine site. Guidance is given in the paper on the issues which must be covered in water right applications.

Jan 1, 1986

By L Yang, L Chen, E Hu, D Tang

Online monitoring of particles cumulative percent passing (PCPP) for a target size at hydrocyclone overflow, compared with traditional offline methods, provides PCPP feedback in real time, and is advantageous in enabling energy-efficient comminution, increasing downstream flotation efficiency, and improving upstream resource knowledge. However, existing online approaches are generally costly and bespoke, and some are sensitive to operational changes. Therefore, this study proposes a new low-cost alternative based on accelerometer measurement for online PCPP monitoring in the overflow of hydrocyclones and provides a preliminary experimental investigation under dry condition. The proposed method uses a sensing probe inserted into the overflow pipe of a hydrocyclone to receive particle impact from the incoming slurry, with accelerometers attached to the probe and mounting frame outside the pipe for particle-probe impact detection. As a preliminary investigation before studying particle-probe impact events in slurry, tests under dry condition without fluids were conducted using dry sand particles in free fall from a fixed height. Accelerometer measurements are analysed in both time and frequency domains through root-mean-square (RMS) and fast Fourier transform (FFT). Results show that accelerometer measurements are useful in estimating mass flow rates, which are correlated to the accelerometer output amplitude RMS values in time domain, in a non-linear mapping. Different particle size classes can be identified by examining the accelerometer output amplitude at a known mass flow rate. Different particle size classes feature their distinct signature frequencies (SFs) that can be examined via FFT and the SF is found to be independent of the mass flow rate. The results imply that any PCPP changes can be detected by the change in the accelerometer output amplitude as well as a shift in SF, which demonstrates the effectiveness of using accelerometers to gauge changes in PCPP. Based on the current findings in dry condition, future work will investigate particle-probe impact events in slurry.

Aug 24, 2022

By T Amiconi

Ernest Henry Mining commenced operations on its copper-gold project in August 1997, some two months ahead of schedule and ten per cent ($35 million) under budget. The mine is located in the highly prospective Mount Isa/Cloncurry mineral district in north-west Queensland, approximately 38 km north-east of Cloncurry. The developer and operator of the project is Ernest Henry Mining Pty Ltd (EHM), an incorporated joint venture between MIM Holdings Limited (51 per cent) and Savage Resources Limited (49 per cent). The deposit is located approximately 40 km north of Cloncurry in North West Queensland and lies beneath a featureless black soil plain with no significant creeks or gullies cutting across the site. Vegetation is sparse and consists essentially of Mitchell grass with occasional low shrubs and trees. Up to nine million tonnes of ore and over 43 million tonnes of waste will be extracted each year from an open pit operation to produce approximately 350 000 tonnes of concentrate when in full production.

Jan 1, 1998

By T Baumgartl, A Costine, B Boshrouyeh, M Edraki

In mineral processing, the management of tailings may become increasingly more challenging with a change of ore type and the quality of water used in the plant. This, in turn, may affect the overall costs of the operation and water usage and, in the long-term, pose challenges for mine closure and rehabilitation. Depending on the applied treatment technique, the short and long-term properties of tailings are largely determined by the fine particles. Most clay materials and ultrafine particles exist in tailings from oil sands, coalmines and base metals, bringing about challenges in dewatering performance. Moreover, given the growing concern for water scarcity, the minerals industry is increasingly turning towards the use of saline water, which poses yet another challenge for tailings management. The high salt content alters the behaviour of clay particles, making dewatering a more complex process than in freshwater systems (Boshrouyeh Ghandashtani et al, 2022; Costine et al, 2018). High-density techniques for tailings management have been used for several years in the mineral industry. In this regard, one of the novel and promising dewatering methods is in-pipe or inline flocculation, where the polymer is added at high dosages to thickener underflows, giving additional (likely denser) aggregation, releasing more water on deposition compared to low solids thickening. Previous research in the field of flocculation has primarily focused on the process of flocculation itself, specifically the settling rate and size of aggregates, rather than the long-term impacts of the produced tailings materials (Liu et al, 2020; Jeldres et al, 2017). This is particularly true for the novel method of this technology, where polymer is added to the thickener underflow. Furthermore, these studies have used small-scale set-ups using buckets/beakers, plungers and mechanical stirrers for the flocculation process. Unfortunately, these methods lack the necessary control over the properties of the treated tailings, which can lead to irreproducible mixing and dispersion of viscous polymer solutions (Fawell, Costine and Grabsch, 2015). Consequently, a system that can work with a wide range of operational conditions for high-solid tailings material is essential for reliable and reproducible results. The objectives of this study were to determine the effect of different type of polymers in the presence of monovalent and divalent salts on the inline flocculation of artificial tailings. The next step was to evaluate the impact of high-dosage polymer addition on geotechnical properties such as settling rate, consolidated density, rate of consolidation and the hydraulic conductivity of tailings. In addition, this research aimed to fill a knowledge gap and investigate the feasibility of using polymer-treated tailing in removing the copper ions and then quantify the performance of produced aggregates under time-dependent processes.

Aug 2, 2023

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

No Paper

Jan 1, 1996

By E Jak, M Shevchenko, D Shishin

One of the key aspects to develop sustainable metallurgical production is to ensure that the predictive power of thermodynamic tools is brought up to a new level of accuracy and reliability. Exploring new polymetallic processes, integrating primary and recycled materials, means utilising the uncharted areas within the Cu-Pb-Zn-Fe-Ca-Al-Mg-Si-O (major) – Cr-Na (slagging) – As-Sn-Sb- Bi-Ag-Au-Ni-Co (minor) slag-solids-metal-matte-speiss-sulfate system. This requires extensive integrated experimental and thermodynamic modelling study, which is underway at PyroSearch at the University of Queensland (UQ).

Aug 21, 2024

Obtaining correct assays for gold determinations relies on the correct methods being chosen and the assayer being made aware of the mineralogy of the sample and its general origin. Usually when a geologist or metallurgist obtains "incorrect" gold assays the problem can be traced to poor communication between the geologist or metallurgist and the assayer.

Jan 1, 1986

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

Diamond bearing deposits are extremely low grade and require large bulk samples to be tested to determine the grade and quality of the stones. The semi portable plants, for treatment of these bulk samples, have followed the development of commercial processes for diamond concentration. These processes included jigs and diamond pans, which have been largely supplanted by heavy media processes for primary concentration, due to the higher efficiencies in all size ranges. A number'of flowsheets including these processes are presented. The final recovery of diamonds from the bulk sample concentrates can be accomplished by rejigging, adherance to grease or by X-ray sorting. Flowsheets incorporating all the processes are presented. Two plants are described; one incorporating jigging, rejigging and hand sorting; the other using heavy media separation, and wet X-ray sorting.

Jan 1, 1984

The methods employed in dressing 'the tin ore up to the required percentage of purity depend mainly on the type of ore crushed.These may be briefly divided into two distinct classes-viz., q, free: milling ore and a complex milling ore. In the former the ore is practically free from the common metallic sulphides, such as pyrites, mispickel, blende, galena, etc., and 1!' clean concentrate of 70 per cent metallic tin can be directly obtained in one continuous act of concentration; in the latter, however, in order to get a good extraction, it is only advisable to primarily concentrate up to 30 to 40 per cent. tin oxide, the rest being the sulphides of the metals. This concentrate is then roasted, re-ground, and re-concentrated up to 70 per cent. metallic tin on a separate set of tables.In the complex milling ore the tin is intermixed very closely with the sulphides, so that it becomes necessary to collect all the mineral present in order to obtain clean tailings. Stamp mills are the most popular machines for the primary crushing in the district, but whether they are invariably the best for the purpose is rather an open question. No doubt for some of the very tough chloritic ores they are the most efficient, but for a brittle quartzose ore, such as the free milling proposition usually is, the writer thinks Oornish rolls would well hold their own, especially when the tin occurs coarse, as is so often the case with this class of ore. Of course, the great drawback to stamps is the excessive quantity of tin slimed and slime tin is one of the problems of tin-dressing-while rolls give...

Jan 1, 1907

By G M. Tranell, M Tangstad

The CO2 footprints in the production of Mn-ferroalloys and silicon/ferrosilicon are correlated with the fossil carbon consumption. The CO2 emissions may be reduced in the Mn-ferroalloy process by increasing the degree of prereduction and reduction of carbonate materials, while the silicon/ferrosilicon process is optimised based on silicon yield. By changing the fossil reductant into biogenic reductants, the global warming potential will be decreased even more. Even if the reductants are biogenic reductants, there will still be a global warming potential (GWP) in eg the electrode consumption and the CH4 emissions in the charcoal production. To reduce the use of fossil reductants there are also more disruptive technologies like the use of H2 that at least for the silicon production is on a very low technology readiness level (TRL). Using metallothermic processes will reduce the use of carbon but requires carbon neutral metal reductants. Electrowinning can have low CO2 emissions, and the electrowinning of pure Mn is a technology of high TRL. Salt and oxide electrolysis is under investigation for both Mn and Si production however the research is still on a low TRL. The use of CCS/CCU (carbon capture storage/utilisation) is a part of obtaining carbon neutral processes. Last, the energy mix used for these energy demanding processes is discussed.

Aug 21, 2024

By Howes PM

In the iron and steelmaking processes, dusts are generated and treated by wet dedust- ing methods to form slurries which are high in iron content, but also contain certain impuri- ties. For many years these slurries have been processed and the wet cake, which is produced, has been dumped because of the high zinc and alkali chloride contents. Sintering is an appropriate process for recycling of these materials, provided the deleterious impurities can be kept under control. Zinc is a deleterious element in blast furnaces because it promotes the formation of accretions on the upper walls of the furnace. This results in irregular furnace performance. Alkali chlorides effect the emissions from the sinter plant waste gas due to the high resis- tivity of these components, resulting in decreased efficiency of the electrostatic precipitator. Experimental work indicated a concentra- tion of zinc in the -11 pmt particle size frac- tion. A cyclone plant was installed producing a "coarse" usable product and a "fine" waste Product.

Jan 1, 1984

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

The explosion at Appin Colliery on July 24th, 1979, demonstrated the need for a large scale facility to simulate an underground type explosion and study its effects. The effects of an explosion cannot be established quantitat- ively using small scale models. A gallery was constructed for this purpose at Londonderry Centre and commissioned in Feb- ruary, 1980. It is 50 metres long, 2.7 metres in diameter, capable of withstanding an internal pressure of 210 kPa and is the only facility available for this purpose in Australia. The gallery has provided valuable inform- ation on blast effects of explosions in tunnels and is to be used for testing the performance of explosion arresting devices, further invest- igation of explosion effects, research into basic explosion phenomena and instrumentation development. Additionally, it will provide a demonstration facility for training purposes.

Jan 1, 1981

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

Traditional methods for the production of transition metals from their ores usually include the electric arc smelting of the ore or concentrate to produce a ferroalloy. This is subsequently refined to produce either a ferroalloy or to produce the metal or metallic carbide. Recent trends in the treatment of iron ores have seen the development of many processes for solid state carbothermic reduction followed by melting of the prereduced iron to produce steel and similar types of processes are under consideration for the production of ferroalloys. There are clear potential savings in energy and control of emissions from such processes. This paper discusses some research which is currently underway at La Trobe University into the solid state carbothermic reduction of chromium and tungsten ores to produce the metallic ferroalloy or the carbide for subsequent further processing. The kinetics of the carbothermic reduction of both chromite and scheelite were found to be dominated by gaseous CO rather than by direct carbon reduction. However the diffusion of carbon into the ore is certainly an important feature of the process. The production of tungsten carbide from the metal is the slow step in tungsten reduction. The development of phases during reduction were studied using a scanning electron microscope and an electron probe and knowledge of the phases produced allows analysis of the reduction process.

Jan 1, 1997