Search Documents

This paper describes the technical development of the Newman beneficiation plant over its 23 years of operation and how this development relates to the mine ore reserves of high-grade and low-grade ore. It also discusses the importance of the beneficiation product grades in the overall blending of shippable products from a range of mines to optimise overall ore resource utilisation. Also discussed is the importance of the ore reserve reconciliations in resource utilisation. Data is provided on the capacity and quality improvement results of the plant upgrade, carried out in 1999. This shows how the original capacity upgrade targets have been exceeded and the additional quality benefits that have been obtained from this capacity.

Jan 1, 2002

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

This paper gives a first-hand account of what a graduate mining engineer can learn by visiting Atlas Copco in Sweden and gives reasons why all mining engineering students should apply for this excellent scholarship. It will also (attempt to) refute the authorÆs mine managerÆs claim that the trip was a huge junket.

Jan 1, 2006

By G Deans, M Longbottom

OZ Minerals’ Carrapateena mine is one of Australia’s newest ‘greenfield’ mining deposits. It will be a 4.25 Mtpa sub level cave underground operation, with an estimated mine life of 20 years. The integration of stakeholder values to inform project development influenced the social and environmental outcomes. A Native Title Mining agreement was developed in 12 months. Project primary approval was obtained 12 months from submission, with achievable licence conditions and one public comment. The project moved from a Pre-feasibility Study in 2016 to construction in 2018. Following recent international dam failures, the Tailings Storage Facility (TSF) was a focus for Government approvals and stakeholder engagement. Significant effort was made into understanding the science around potential effects, impacts and risks. A leading practice Impact Assessment Framework that identified Sources, Pathways and Receptors was applied. A process of failure mode identification and layers of protection analysis was undertaken for robust design controls at each stage, while simultaneously transitioning between downstream and upstream discharge arrangements. Participatory selection of the TSF site and design layout was critical in managing project costs and environmental constraints, and in incorporating cultural heritage constraints and technical risks.

Jul 1, 2021

The New Broken Hill Consolidated Airshaft is the first major undertaking in the development of New Broken Hill Consolidated Ltd's. property, which adjoins that of The Zinc Corporation Ltd. on the latter's southern boundary.The Zinc Corporation ore-body has a southerly pitch. The Zinc Corporation's New Main Shaft is 1000 ft. north of the common boundary, and the general plan of development of the New Broken Hill Consolidated property is by driving south from this shaft on the lower levels. No downcast airway from the surface was available south of the Zinc Corporation's New Main Shaft; this shaft acts as the main downcast to the bottom of the Zinc Corporation mine, the general air flow then being northward and upward to the upcast shaft at the extreme north end of the Zinc Corporation property.Rock temperature is 920 F. at 2000 ft., increasing by 10 Fahr. each 72 ft., the rock temperature at 3000 ft. being estimated at 1060 Fahr. With the general air flow northward from the Zinc Corporation's New Main Shaft, adequate ventilation under these temperature conditions would not be practicable for any great distance south of this shaft without another main airway from the surface. Accordingly the New Broken Hill Consolidated Airshaft is being sunk at a point 1000 ft. south of the common boundary, i.e., 2000 ft. south of the Zinc Corporation's New Main Shaft, to ventilate future New Broken Hill Consolidated workings and that part of the Zinc Corporation mine between the boundary and the New Main Shaft.

Jan 1, 1940

By T Goswami, G Brent

In response to concerns over greenhouse gas (GHG) emissions and an imposed cost in some jurisdictions, many mining houses have committed to reductions in their GHG emissions. However, mining faces particular challenges in this regard, notably from increasing strip ratios. Furthermore, mining activity around the globe is not expected to decrease in the foreseeable future as mineral demand is driven up by the aspirations of rapidly-developing nations. Novel approaches will thus be needed if any reductions in energy consumption and GHG emissions of mining are to be achieved.This paper presents some directions for the mining industry to pursue in reducing their GHG impact, focusing on the difference that blasting methods can make. Importantly, large productivity and revenue gains can also be realised from these methods.Key directions considered here include optimising resource recovery and quality through:reducing coal damage and loss from throw blastingrecovering thin coal seamsproducing cleaner coal with less dilution.Blast design can also significantly improve the productivity of surface mining by:improving muck pile shapingimproving mine equipment productivityimproving scheduling.We show how a particular blasting method can eliminate coal loss in overburden throw blasting and can lead to large increases in coalmine profitability. Thin seams that were previously wasted can also be recovered with this method. Furthermore, the method has been implemented to combine several separate drill and blast cycles into a single cycle, leading to productivity gains.An illustrative example is given to show how increased coal recovery can increase revenues and more than offset any potential GHG emissions liabilities. Overall mine energy and GHG emission intensities can thus be reduced.CITATION:Goswami, T and Brent, G, 2015. Blasting approaches to increase mine productivity and reduce greenhouse gas emissions in surface coal mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Poliakov, E Donskoi, K Vining

The automated optical image analysis software Mineral4/Recognition4 (M4/R4) is capable of performing comprehensive characterisation of different materials throughout the iron ore value chain, including ore fines, lump, sinter, pellets and coke. It has been successfully used by CSIRO for industrial and research projects and has been independently licensed to several world leaders in iron ore production and ironmaking. The M4/R4 software was strongly integrated with a Zeiss microscope to make use of the company’s powerful AxioVision software. This required users to own both Zeiss microscope hardware and AxioVision software in order to be able to use M4/R4 to its full image acquisition and analysis capacity. Therefore, it was not available to the users of equipment produced by other major microscope manufacturers. In recent times however, Zeiss has indicated that the AxioVision software will no longer be supported. To overcome this limitation, CSIRO has proceeded with the next generation of this software, Mineral5/Recognition5 (M5/R5). Importantly, the M5/R5 system has been developed without any dependence on a specific microscope hardware/software platform. Furthermore, the image analysis functionality is now based on openCV open access software and has been fully rewritten using stateof- the-art software development tools to allow reading and processing of all major image formats. Although past applications have been specific to iron ore and ironmaking applications, other improvements, such as an increased number of minerals allowing better gangue segmentation, flexible mineral definitions, improved software modules behaviour and refined analysis routines enables the platform independent M5/R5 image analysis system to be used by researchers in any area of mineralogical or materials research.

Nov 8, 2021

By K G. van den Boogaart, U Mueller

"An accurate prediction of benefit for some types of ore may require not just the ore grade, but a whole compositional characterisation of the estimates; that is, its full mineral composition including waste composition and nuisance elements. An example is Nickel laterite ores, where Ni/Co content must be complemented by estimates of many other elements, as these might have a notable impact on ore processing.Estimates are often obtained with (co-)kriging or co-simulation; however, geostatistics applied to compositional data may yield spurious and inconsistent results because of the constant sum constraint. The log-ratio approach avoids such problems. It proposes a three-step procedure: data are mapped to a set of log ratios of components; for example, the additive log-ratio transformation (alr) transformed scores are modelled with an appropriate fully multivariate geostatistical toolbox; for example, direct/cross-semivariograms and co-kriging or co-simulation results are back-transformed to the original units.Some practical aspects may make the application of this technique difficult: the assumption of Gaussianity and the high dimensionality of the compositions combined with the need for using multivariate methods. This contribution compares several ways of treating compositional data (combining normal score transformation, log-ratio transformations, and minimum/maximum autocorrelation factor (MAF) decomposition) with respect to their ability to generate sensible simulations. The various approaches considered are illustrated with a Nickel laterite data set for which ten variables are available. Both theoretical considerations and illustration results suggest that the best combination is (log)ratio-normal score transform-MAF, in this order. The factors so obtained are closer to Gaussian, approximately spatially decorrelated and can be simulated independently. Simulations can later be recombined to alr-simulations, which in turn may be converted back to point compositions. The resulting simulated compositions are compared with a full Gaussian co-simulation of the raw data. The log-ratio methods show reasonable to good reproduction of mean values, and distribution of the data set and by construction satisfy the total sum constraint, in contrast to the simulations based on raw data for which the total sums fluctuate strongly.CITATION:Mueller, U, Tolosana-Delgado, R and van den Boogaart, K G, 2014. Approaches to the simulation of compositional data – a nickel-laterite comparative case study, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 61–72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By A V. Ozsever

The selectivity in flotation columns involving the separation of particles of varying degrees of floatability is based on differential flotation rates in the collection zone, reflux action between the froth and collection zones, and differential detachment rates in the froth zone. Using well known theoretical models describing the separation process and experimental data, froth zone and overall flotation recovery values were quantified for particles in an anthracite coal that have a wide range of floatability potential. For highly floatable particles, froth recovery had a very minimal impact on overall recovery while the recovery of weakly floatable material was decreased substantially by reductions in froth recovery values. In addition, under carrying-capacity limiting conditions, selectivity was enhanced by the preferential detachment of the weakly floatable material. Based on this concept, highly floatable material was added directly into the froth zone when treating the anthracite coal. The enriched froth phase reduced the product ash content of the anthracite product by five absolute percentage points while maintaining a constant recovery value.

Jan 1, 2005

By K T. Broekman, R L. Koenig

"The Braemar Iron Formation is atypical ore when compared to the current magnetite ores being processed. In attempting to process and economically recover the vast quantities of iron ore stored within the Braemar Iron Formation, æshifting the paradigmÆ is required. The formation has a low Davis tube recovery (DTR) grade of 15 - 20 per cent, which is much lower than magnetite ores processed in Australia. Despite this, by thoroughly testing and understanding the ore characteristics, it is found that the Braemar ores have significant advantages to processing than the harder banded iron formation (BIF) and taconite resources.The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. The grade was low and the Pilbara region discovery lead to the development of high-grade direct shipping hematite ores. Carpentaria Exploration (CAP) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. Shifting the paradigm away from grade the advantages of processing this ore are achieved by having an extremely low waste to ore ratio, lower Bond work index, lower abrasion levels and high-grade magnetite concentrates with little impurities other than silica. While developing the Hawsons Iron Project (HIP) it became more apparent that a positive business case is achievable when the following factors are exploited: very large resource - the resource is contained within one pit the rock fractures easily along grain boundaries - ideal for cheap impact crushing of the ore the ore is extremely soft, with a Bond work index of 6.3 - 8.0 kWh/t all major infrastructure required is readily available - rail, power, access and port the mine is in close proximity to Broken Hill - rich mining history and skill set available the resource contains many billions of tonnes of magnetite mineralisation.Shifting the paradigm by selecting equipment suitable for processing soft ores and not hard BIF or taconite ores and taking locality and available infrastructure into account may change the way people approach new low-grade resources in future.CITATION:Koenig, R L and Broekman, K T, 2013. Understanding ore characteristics and equipment selection, in Proceedings Iron Ore 2013, pp 403-410 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

Two key elements in the design of a pastefill or high density backfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: Vacuum or pressure filters. These represent the ætraditionalÆ approach to the preparation of pastefill. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producingpaste/high density backfills. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach.This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material. No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mines in Canada.

Jan 1, 1998

By Wang J, Ma Y, Jia H

The Hedong Gold Mine is located in the Yan(ai area, tihandong hroo%ill, e. China. It is an underground mine with an annual gold output of some 700 0(H) grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called 'sublevel open and fill stoping method' in the mine. Experience to-date is that new mining method is Satisfactory.

Jan 1, 1998

By Behl S

Flocculation behaviour of six different dolomite samples, four from the Florida mining district, one from Perry, South Georgia and another from New Jersey was examined using polyethylene oxide (PEO) as a flocculant. The samples were similar in chemical composition, however the porosity of the samples from the Florida mining district was higher than the others. FT-IR, adsorption and surface modification by leaching revealed that flocculation was directly related to the presence of isolated hydroxyl groups on the surface. The adsorption mechanism was believed to be hydrogen bonding of the ether oxygen of PEO with isolated -OH sites on the solid.

Jan 1, 1993

By Tapp B. A

The minerals industry in Australia is currently regarded as the country's economic saviour; the bastion of economic security. As Fitzgerald (1974) stated, 'Australia's natural endowments in minerals are the envy of most countries of the world'. As a result the proposed new mineral developments are on a scale that hitherto in the sixties would have been completely unenvisaged. It is reported that Australia is poised on the verge'of a sixteen billion dollar mining-based investment boom: a boom that will see Australia dominate the energy export field, the mineral processing field, and create the 'coal dollar'. This growth scenario has many inherent dangers, and it is the authors' contention that these should be carefully considered before further development proceeds. Two of the major problems related to the mineral industry growth scenario are the predictability of the future metal market, and the energy cost of mining. The latter problem is the one discussed here. The mining-mineral processing industries in Australia currently use about 36% of Australia's primary energy

Jan 1, 1980

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By M R. Lane, M L. Cramer, N P. Wines

Increasing attention is being focused by regulators and industry on the residual environmental liabilities associated with mining projects following site relinquishment (termed surrender in Queensland). Even sites that have been rehabilitated to a high standard and to the satisfaction of the regulator are not completely risk free and may require some degree of ongoing management. As well as ongoing monitoring and maintenance costs, considerations should include how costs associated with potential risk event occurrence can be quantified and, if considered material, how provisioning should be undertaken to minimise the risk to the state and to taxpayers. In Queensland for example, once a resource site is fully rehabilitated and meets its environmental authority conditions or rehabilitation completion criteria, the tenure and environmental authority can be surrendered. During the surrender process any ‘residual risks’ resulting from the use of the site for the resource activity must be considered, and, if requested, a payment given to the government to cover any ongoing management and risk costs. Accent Environmental, in conjunction with Lane Associates, was engaged by the Queensland Government as part of the government’s financial assurance framework reforms to develop an innovative, ‘one-size fits most’ Residual Risk Calculator for the Queensland resources industry. The calculator is an Excel-based tool that uses detailed user inputs to estimate post-surrender management requirements and liability at resource sites. If residual environmental risks associated with rehabilitated mine sites can be identified, quantified and managed through pragmatic regulatory tools and effective provisioning, site relinquishment/surrender can be achieved without compromising environmental and social outcomes or exposing the state to unreasonable financial risk. The effective management of residual risk can also help facilitate operations as well as relinquishment/surrender of sites where a ‘walkaway’ solution may not be otherwise technically feasible.

Aug 2, 2023

By N Takamatsu

The environments surrounding the iron and steel industry have changed greatly in recent years. Reported in this paper are the technologies adopted by the Japanese iron and steel industry to fititself to change in global steel demands, degradation of iron ore and coal, prolonging service life of the facilities and requirements of energy saving. In addition, innovative technologies for CO2 emission control in iron making processes are also discussed.

Jul 11, 2011

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011