Search Documents

By D La Rosa, D Bennett

"Exploration drill core provides for a number of standard measurements essential for determining the viability of a new mine or the extension of an existing one. Rock lithology and alteration can be visually determined and grade measured from the half core. Geotechnical parameters such as rock strength and structure can also be measured. Using suitable proxies, these metrics can then be used to estimate run-of-mine (ROM) particle size. In combination with comminution test results, these can subsequently be used to design comminution circuit configurations and estimate their performance.The Frieda River Project drill core for the large Horse-Ivaal-Trukai copper-gold porphyry deposit was unusual due to a late stage gypsum-anhydrite stockwork event that overprinted much of the deposit. Above the base of the oxidised zone, which closely matches the water table, gypsum and anhydrite has been leached out, effectively removing the glue holding the rock mass together. As a result, much of the rock above this gypsum-anhydrite surface is fragmented and gravel-like in texture, while the material below this horizon is typically uniform and competent.Large volumes of the orebody above the gypsum-anhydrite surface are expected to need minimal or no blasting for efficient excavation. In addition, the fragmented nature of much of the material was expected to reduce comminution specific energy as it already appears as though it has been crushed. While this was expected to have positive impacts to the operation, the lack of standard geological logging methods available to accurately define the degree of in situ fragmentation led to difficulty in gaining certainty over the ROM product and grinding circuit feed size distributions.Using the extensive library of core photos for the project, a novel method using image analysis techniques to take both the intact core and gravel into account to predict ROM fragmentation was developed. In addition, existing point load test data was used to infer the strength of the rock and its impact on the blasting, crushing and grinding processes. The novel approach allowed development of ROM size distribution data and improved certainty in the results of comminution circuit designs.This paper describes the methodology undertaken in detail, and discusses the results obtained.CITATION:Bennett, D and La Rosa, D, 2016. The Frieda River Project – a Novel Approach to Analysing Exploration Drill Core: How Broken is Broken?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The current boom being experienced by mining, coupled with a shortage of professionals, will mean those in the industry will have many choices. It may be easy to become carried away and run with the highest bid or the biggest promise. Without planning, however, the ærightÆ opportunity may be missed and there may be some long-term consequences. There are many choices of paths in the industry to suit work preferences, life cycles and to achieve a balanced life. People in mining have changed jobs and companies frequently û which means new leaders need to take greater responsibility in charting their own direction. Career options need to be carefully assessed and aligned to personal values and preferences. Emphasis is given on gaining site experience early on.This paper examines strategies for career planning, which incorporate life cycles, education and what is meant by a balanced lifestyle. Two tools are identified as being helpful in ensuring strategies can be successfully executed. They are ævisioningÆ and æinfluenceÆ.To make the mining industry more attractive, we need more creative solutions around advances in technology and organisation of work. It also needs the input and leadership of new entrants in to the industry to assist in its survival. New leaders are encouraged to voice a vision and effectively influence their companies. New leaders have little authority and need to learn how to effectively influence. We as a mining industry need to listen, be open-minded and give it a go.

Jan 1, 2004

By S J. Neethling and, S J. R Simons

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, have been investigated. In this study two bubbles of equal size were formed and forced to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. Data of coalescence frequency and time is presented, as well as images of the coalescence events. The coalescence frequency was used to validate a parameter, Pf, known as the film failure frequency, used in a simulation model to predict foam height in a gas-sparged vessel. Predictions determined using Pf were then validated by experimentation.

Jan 1, 2005

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That sub- ject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public atten- tion has focussed as never before on the subject of commodity prices. To advocate stabilizing com- modity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent f.11 1k

Jan 1, 1978

By P Ottenio, B CarrT

In the last 40 years, the froth flotation process widely spread in the paper industry becoming the dominant technology for ink removal from recovered paper slurries and cellulose fibres recovery. Most of current models used to describe the flotation deinking process are based on hydrodynamic and statistical theories of ink particles collision/attachment to air bubbles. The complexity of these theoretical models, together with the variability of the recovered papers composition, does not allow to define a set of æeasy to handleÆ equations to be used for modelling industrial flotation cells. This main limiting aspect makes that, in several deinking process modelling tools, basic parameters used to characterise the flotation unit, ie yield, ink removal efficiency, water loss, are constant parameters. Although in some process simulation tools the flotation yield/efficiency is adapted to process control parameters (air ratio, pulp flow, pulp consistency), physicochemical variables (namely the pulp frothing aptitude, the pulp surface tension and the ink adhesion energy to air bubbles) are not taken into account to adjust the flotation yield/efficiency. Data collected during recent laboratory and pilot plant experiments focusing on the role of surface active substances on the flotation efficiency were therefore interpreted and used to identify general trends that could be described with simple semi-empirical models. A set of model equations using surface tension and froth removal height as main variables was then defined in order to describe the behaviour of a pilot flotation cell. Trends obtained during the dynamic simulation of the deinking pilot plant were in good agreement with experimental data obtained under similar experimental conditions, thus indicating that developed equations can forecast with good approximation the behaviour of a flotation deinking unit.

Jan 1, 2005

By M Yahyaei, F Vos, J Siliezar

Site-based case studies (including data collected from industrial surveys) and their application in evaluating circuit performance, have a significant role in developing reliable process models. Such models are useful to both plant metallurgists and researchers. Appropriate process models enable the plant metallurgist to assess the impact of different operational parameters on the overall circuit performance. They also provide the researcher with a detailed understanding of process behaviour in response to changes in ore characteristics and process conditions (ie plant throughput, ore competence, ore type). Thus enabling the identification of effective operating factors, and allowing them to be ranked in order of their influence on the process response, which eventually develops into a process control tool in the hands of plant operators.The above approach has been developed and applied at the Julius Kruttschnitt Mineral Research Centre (JKMRC) separately for both comminution and flotation processes. In recent years, the JKMRC has attempted an integrated approach by developing process models that incorporate the impact of upstream processes on downstream processes. This is not possible using the traditional approach of separate comminution and flotation surveys, so conducting integrated plant surveys is crucial for success in developing integrated process models. This paper summarises industrial experience gained while conducting such an integrated plant survey at Glencore’s Ernest Henry Mining operation near Cloncurry in north Queensland. An appropriate approach should be taken to enable the alignment of different requirements from different processes during the plant survey. This, as well as the challenges faced in integrating comminution process models with flotation process models, are identified.CITATION:Yahyaei, M, Vos, F, Powell, M S, Siliezar, J and Perkins, T, 2014. Challenges in developing integrated process models based on industrial survey data, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Zengerer

The Basil Cu/Co deposit comprises a 26.5 Mt Inferred Resource of copper and cobalt, grading 0.57?per cent Cu and 0.05 per cent Co. It lies in the Harts Range, Central Australia, within the Riddock Amphibolite of the Irindina Province. Analysis of drilling within the mineralised zone of the deposit determined a spatial association between pyrrhotite with high magnetic susceptibility and chalcopyrite, following a strong magnetic trend as determined from airborne geophysics. A study was commissioned to examine if geophysical inversion could predict the distribution of sulfide mineralisation based on pyrrhotite from drill hole intersections, as well as predicting further mineralisation at depth or in the vicinity of the deposit. Petrophysical and geostatistical analysis of drilling susceptibility and mineralisation provided a basis of property distribution inside the model. This was followed by 3D geological modelling of mineralisation based on domain kriging of drill hole susceptibility sensitivity testing of signal to source depth, and distribution was performed using 3D forward modelling. Stochastic inversion generated alternative 3D geological models, which were tested for behaviour and adherence to observed drilling data and geostatistical limitations using GeoModeller software. Predicted mineralisation distribution was compared with conventional geostatistical modelling and found to be in agreement in planar behaviour but exhibiting possibly isoclinally folded trends, with reliability increasing closer to the surface. Predictions of mineralisation at greater depth and beneath weaker anomalies were more diffuse due to small model cell size having limited influence on the signal at depth.The Blackbush uranium deposit comprises a 64.5 Mt Inferred Resource, grading 230 ppm U in the Pirie Basin south of Whyalla, South Australia. It directly overlies the radiogenic Samphire Granite and is considered a tertiary unconformity deposit. Sensitivity modelling was performed using high-resolution ground gravity to see if a deposit signature could be detected using gravity. This required 3D implicit modelling of the geology and mineralisation from drill hole data and characterisation of an associated physical property model using domain kriging in GeoModeller. Density models relied on exploiting an observed relationship between logged density and measured uranium oxide percentage. The residual gravity response of the background geology model identified the location of the uranium deposit. Stochastic inversion of the litho/property 3D model has refined the known distribution of uranium from drilling and provided structural insights into the deposit.These projects have become excellent case studies for exploiting the relationship between mineralisation and potential fields and for testing the applicability of using domain kriging of properties determined from drilling to build robust 3D geological models for stochastic geophysical inversion, leading to robust methods for exploration targeting and mineral deposit prediction.CITATION:Zengerer, M, 2014. Use of geostatistically-constrained potential field inversion and downhole drilling to predict distribution of sulfide and uranium mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By ALAN J. HARGRAVES

It is normal that Shepherd and Rixon, in their contributed discussion (this issue) see differences with Hargraves (1983), as it exemplifies the present uncertain situation worldwide, a situation expected to remain until better understanding and wider agreement lead to the real goal of the prevention of instantaneous outbursts of coal and gas.

Jan 1, 1983

By P Audet, D Doley

The mining industry often embraces mine closure criteria that require the reinstatement of predisturbance or even presettlement (ie historic) ecosystems. However, the extent and severity of disturbance associated with most mining activities mean that critical physical and biological characteristics are irreversibly altered. Consequently, it is rare that a reconstructed landscape can support ecosystems even close to the historic condition, and this rarity is reflected in the small number of mine leases that have been extinguished by attainment of such completion criteria. Novel ecosystems are defined as those in which some or all physical and biotic components are irreversibly different from the historic condition. Recognition of the concept of novel ecosystems allows mine closure criteria to be set according to attainable physical and biological conditions that provide safe, stable and manageable environments with acceptable ecological functions. We propose that a landscape that first maximises physical stability and economy yet will provide a range of environments for vegetation communities and fauna habitats that may be very different from those existing prior to a disturbance should be considered suitable alternatives to, eg targeting idealised historic environments. As a result, mine closure criteria should be established by detailed description of the best attainable physical conditions, with negotiated identification and testing of the most appropriate biological systems for the various parts of the reconstructed landscape. As a general practice, revegetation would use native, but not necessarily local species if the new physical environment is not conducive to the survival and growth of local species. These new ecosystems would need to be managed in perpetuity, although the intensity of management might be low if landscape design and engineering are combined with appropriate species introductions. Here, we suggest an abbreviated procedure that may be adapted in light of local conditions and circumstances for guiding decisions influencing the physical and biological properties of reconstructed landscapes that will enable novel ecosystems to meet realistic closure criteria.CITATION:Doley, D and Audet, P, 2014. Changing restoration priorities in the 21st century – opportunities for novel ecosystem design in mine closure, in Proceedings Life-of-Mine 2014 , pp 649–662 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By G Cao, Y R. Cui, J X. Zhao, H P. Gui, G H. Wang, Z M. Wang, M M. Ren, B Li

Pyro-metallurgy is still the main process for lead production and a lot of lead direct smelting processes have been developed in recent years. All the processes will experience two steps in common. The first is the oxidisation of PbS to PbO and then reduction from PbO to Pb, furthermore, from ZnO to Zn. So, the composition of melts, especially the slag composition at reduction step change continuously. Up to now, there are few systematic results on the slag physical-chemical properties with its composition change. In this work, the typical lead direct smelting processes were analysed from theoretical and practical standpoints. The full-period slag composition and slag melting point change were compared. Especially, to the PbO and ZnO reduction steps, based on the full-period slag composition change, the slag properties were predicted. Based on dust composition and test results, the mechanism of Pb compound evaporation and its effect on practice and measurement of high PbO bearing slag physical-chemical property is discussed. It is suggested that to restrain the evaporation in practice and to obtain more accurate measurement results of physicochemical properties of smelting slag are the key problem not only to set high efficiency, energy saving process, but also to environmental pollution control.

Aug 21, 2024

By F R. M Pires, R M. Carvalho

Supergene processes in banded iron formation (BIF) result in important dissolution, material transport and simultaneous disorder of the residual bands. The rock physical properties such as density, porosity and rheology change during the weathering attack. The itabirite, Paleoproterozoic metamorphic BIF from Quadrilßtero Ferrffero (QF) û Brazil, shows several weathered facies. Strong linking between topographic surface, rock density and iron grade occurs within the weathered zones. This linking is due to partial dissolution of silica and carbonate from itabirite and gravitational rotation and break of the remaining blades, generating kink-like slump structures. The original itabirite density, 3.7 t/m3, decrease at the first leaching steps, until 2.7 t/m3, and increase at the end of the leaching process until 3.6 t/m3. Iron grade increases from 38 per cent to 68 per cent and depressions (sinkhole), subsequently filled by Cenozoic basinal sediments, are developed over the enrichment zones. The formation of important supergene iron ore deposits of QF is intimately related to such a process. Several iron deposits at QF, such as Pico do Itabirito, Fßbrica Nova, Casa de Pedra, Tamanduß, -gua Claras, Cappo Xavier, etc., reveal the aspects related to the proposed evolution, implying that the formational process of the soft iron ores had a regional character. Granular medium model helped in the understanding of the development of the structure and the formation of the deposits. A numerical model has been developed in order to simulate a leaching system in a two-dimensional matrix, composed of two types of materials: leachable and unleachable. Equal volume proportion and vertical banding were considered. Drilling data was used as multipoint attractors to remove leachable matrix nodes.

Jan 1, 2002

By J Morgan

Regular monitoring of surface deformation over mine sites is important for providing updated information to managers regarding geotechnical risks related to ground instabilities. This is particularly true in cases where unexpected or accelerating movement patterns are observed, as these trends may have implications related to worker safety within active mining environments, as well as continuity of ongoing operations. InSAR is an active remote sensing technique that uses radar satellite imagery to precisely measure ground movement. This technology has started to become a standard tool for monitoring surface stability in many different sectors, including underground and open pit/cut mining applications. In recent years the launch of satellites that collect radar imagery on a more frequent basis, coupled with advances in InSAR processing techniques, has improved both the extent to which movement patterns typical of mining operations can be characterized and the temporal scale on which results can be reported to geotechnical departments. As a result of these developments, InSAR monitoring can now better meet the operational needs of mine sites. An overview of the more recently launched satellites that have a particular relevance to the monitoring of mines is provided, along with an explanation of the InSAR tools that are the most valuable to mine managers and geotechnical engineers. First, broad differences between high resolution X-band imagery and low resolution (but freely available) Sentinel imagery are discussed. Second, the various InSAR tools and their particular applications for different types of mine sites and operations are covered, which include fast delivery deformation maps for short-term reporting, multi-interferometric algorithms for longer-term analyses and rapid movement tracking (RMT) for emergency monitoring or high-risk situations. The ability of the technology to resolve 2D and 3D movement is also touched upon. Practical examples of InSAR application over a variety of mine sites will be presented, as well as surrounding hazards including landslides, to illustrate how InSAR can help provide geotechnical engineers with a picture of surface stability over the full mine site and surrounding areas to help manage risk. CITATION:Morgan, J, 2018. Wide area mapping of ground instabilities from space: InSAR for geotechnical risk assessment and hazard monitoring, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 375–382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Jak, G Khartcyzov, M Shevchenko

The increasing complexity of ore resources and recycled materials in the feed of pyrometallurgical processes present a technical challenge to the metallurgical engineers working on maximising the recovery of the valuable elements and minimising the environmental impact of the processes. To address this challenge, the availability of computational tools that can predict the mass and energy balance in complex systems is required. Then the accurate description of phase equilibria in the complex multicomponent systems describing the chemistry of the pyrometallurgical processes becomes critical for the correct implementation of the indicated tools and facing the outlined industrial challenges. In the present study the distribution of selected elements (Pb, Zn, Fe, As, Sn, Sb, Bi and Ni) between oxide liquid and metal in the ‘CuO0.5’-CaO-AlO1.5 system in equilibrium with Cu metal at 1400°C (liquidus of CaAl2O4) was experimentally studied using the equilibration and quenching technique followed by the electron probe X-ray microanalysis of the resulted samples. The study covered a wide range of effective p(O2) over the system from 10-11 to 10-3.5 (corresponding to formation of immiscible CuO0.5-rich slag). To avoid loss of volatile elements (Pb, Zn, As, Sn, Sb and Bi), a correlation between ‘CuO0.5’ in oxide liquid and p(O2) in open system was obtained first, followed by studying the volatile elements distribution in closed conditions (Al2O3 crucible sealed in SiO2 ampoule), where ‘CuO0.5’ concentration was used as a marker to evaluate the effective p(O2) over the system. The experimental results were then used for the optimisation of the thermodynamic model parameters of the system as part of the integrated experimental and self-consisting thermodynamic modelling research program of phase equilibria in the Cu-Pb-Zn-Fe-Ca-Si-Al-Mg-O-S-(As, Sn, Sb, Bi, Ag, Au, Ni, Cr, Co and Na) gas/oxide liquid/matte/speiss/metal/solids system.

Jun 19, 2024

By Lock PR

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 kin north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bed's life cycle of construction and placement and mucking of ore from the marker bed.

Jan 1, 1998

By M I. Pownceby, S P. Suthers, V Nunna, G J. Sparrow

Global demand for iron and steel has increased substantially over the past 20 years and there has been a greater focus on developing suitable processing options to treat low-grade hematite-goethite ores containing higher levels of silica and alumina impurities. The processing applicable to reduce the impurity levels in these lower-grade iron ores depends on their mineralogy and a thorough understanding of the process dynamics associated with the separation technology. Different separation technologies used to remove silica and alumina from low-grade iron ores were reviewed. The major concentration methods that may be applied to upgrade lower-grade lump iron ores include magnetic separation, wet and dry heavy media separation, and air-pulsed jigging. The technologies applicable to beneficiating iron ore fines include wet and dry gravity and magnetic separation, flotation, and roasting followed by magnetic separation. It is necessary to investigate the application of separation technologies on a case-by-case basis to select economically viable beneficiation strategies suitable for the particular low-grade iron ore. A commercial flow sheet is expected to involve the implementation of several separation technologies.

Nov 8, 2021

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Ahler

Future developments in the mining sector will be driven by the need to increase safety, ecological sustainability and efficiency. Autonomous systems represent a huge step towards achieving these goals. This paper describes the basic infrastructure of an autonomous system – essentially a network of distributed sensors. Although the sensors are distributed, the overarching communication network with its related middleware offers a transparent and uniform layer. This middleware acts as an abstraction layer which priorities information and provides information to other platforms on request. This permits higher-level autonomous functionality to utilise all information available in the system regardless of where data has been generated or via which physical communication link it has been processed.The Personnel Proximity Detection (PDD) system is described in detail as an example, with details not only of the system itself, but also of the essential full integration and how the abstraction layer allows this technology to be plugged in at any location of the network. The paper ends with a summary of the content and a conclusion.

Nov 22, 2011

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By J Channell, G Phillips

"The Chesney deposit, located 4 km south-east of Cobar consists of three copper-gold rich shoots that lie within a larger, copper dominant lode. A fourth gold rich shoot is located adjacent to the main deposit. The deposit exhibits a strong structural control on mineralisation, as brittle deformation during subvertical extension provided the requisite structural traps to precipitate sulfides from solution. It is postulated that the Great Chesney Fault acted as a fluid conduit, conveying fluids to the site of orebody formation. The continual supply of fluids resulted in cyclic brittle deformation when the fluid pressure exceeded the lithostatic pressure and the tensile strength of the Great Cobar Slate.Evidence supports the hypothesis that ore deposit formation was controlled by: a supply of mineralised fluids transported along the Great Chesney Faulta suitable location for the mineralised fluids to accumulate, accommodated by vertical extension and dilation in certain locationsthe creation of suitable structural traps to capture the sulfides. These traps formed as a result of fault-valve behaviour. Understanding the controls on mineralisation enables prediction of the location of other deposits with similar emplacement history, or extensions of current deposits.CITATION:Channell, J and Phillips, G, 2014. Understanding mineralisation controls – a case study of the Chesney deposit, in Proceedings Ninth International Mining Geology Conference 2014 , pp 301–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By J Berg, M Hahn, R Winkel

Imaging sensor systems designed for the mining and minerals industry incorporate different physical measurement technologies that can be used to detect the machine environment, such as laser, ultrasonic/sonar, video and RF-sensors. The underlying physical measurement principles cannot be employed in most applications near the face without regular maintenance due to the harsh environmental conditions like dust, dirt or moisture. However, that is the area, where imaging sensors are most valuable to the machine operator. In the domain of 2D radar sensors these have been either restricted by the angular coverage area or by limited adaptability of signal processing algorithms. The unique full digital solid state design will establish a generation step in mining applications.In order to fill this gap of terrain imaging sensors, the Institute for Mining and Metallurgy Machinery (IMR) of the RWTH Aachen University, in cooperation with the radar company indurad, developed an imaging sensor based on radar technology employing the digital beam forming (DBF) concept. Through multiple transmitting and receiving antennas the sensor delivers high accuracy range and angular information. Using adaptive digital signal processing with multiple imaging algorithms and target detection routines, data of the surrounding environment can be used to enable automation functions in mining.A comprehensive range of radar scans in different environments have been evaluated and benchmarked by using laser scanners. Accuracy measurements in range and angular direction have shown minimal differences. Experimental measurements have been performed at slopes, on conveyor belts and hot cement clinker silos. The experimental system uses a frequency modulated continuous wave (FMCW) front-end combined with a processing unit for signal analysis and target detection.

Sep 26, 2011