Search Documents

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J T. Smit

The theory of froth flotation developed slowly, in almost all cases lagging behind practical developments in the operation of flotation processes. This was largely the result of a lack of understanding of the required basic principles of chemistry and physics, many of which were being developed at the same time. A review of some of the early theories propounded is worthwhile, and should encourage those who are presently studying or practicing flotation to exercise some care in claiming a complete understanding of the underlying phenomena in the art. This paper considers theories presented up to and including those in Principles of Mineral Dressing by Antoine M Gaudin (1939). Of course, developments since that time are important, but they are beyond the scope of this discussion.

Jan 1, 2005

The issue of retrenchment is a topic of considerable relevance for the Papua New Guinea (PNG) mining, petroleum and gas industries. The unique environments in which Porgera Joint Venture (PJV) and other similar operations operate are likely to confront these industries with particular dilemmas that will require a range of investments to mitigate the problems associated with retrenchment and employment. This paper discusses retrenchment and employment in the PNG mining industry using the specific case study of PJV. The paper deals with the issue of employment and retrenchment of local workforces in the PNG context, which presents a serious challenge for the resources industry and the achievement of sustainable development objectives. The issue of future retrenchment of the workforce as a result of mine closure is an obvious challenge for both PJV and the Porgeran community at large, who have now come to rely upon both the employment opportunities presented through the mining. This paper examines these challenges and in doing so highlights some progress made by PJV. The paper also discusses downsizing, strategic practices and holistic approaches of retrenchment and employment. In doing so the paper highlights issues that have been overlooked in both academic and applied studies from global and local perspectives in the PNG mining sector. The latter sections articulate the relevance of the information provided by the case study in the wider context of retrenchment. The conclusion promotes a perspective that a great deal more investment will be required by all stakeholders to respond to the challenges of managing retrenchments and mine closure.

Jan 1, 2009

By M J. Nugus, F Clark, E J. Hill, J T. Carswell, J S. Cleverley, N H. S Oliver

High-nugget gold orebodies are difficult to model in 3D because samples from diamond drill core are generally too small to provide reliable estimates of the gold content of the larger body of rock, and therefore interpolation of gold assay values between drill holes is also unreliable. As a result, gold resources are generally underestimated in areas of high nugget. In practice, proxies for gold mineralisation, such as presence of alteration, specific structures or high vein density, have been used by geologists to predict rocks which are favourable for mineralisation. However, there has been no automated method for combining the predictive capabilities of several proxies, except by human judgement.We have been developing a method to combine several different types of geological features or geochemical analyses into a single measure using conditional probability. Conditional probability provides a meaningful numerical measure for the favourability of rocks for containing high-grade gold mineralisation. This measure can be interpolated in the exploration space, providing a sound basis for a 3D model of the orebody. We have developed this technique using data from the Sunrise Dam Gold Mine, which is a high-nugget orebody hosted in a structurally complex Archaean greenstone belt and which has historically proved to be a very challenging orebody to model.CITATION:Hill, E J, Nugus, M J, Clark, F, Oliver, N H S, Cleverley, J S and Carswell, J T, 2013. Predictive three-dimensional modelling of nuggety gold orebodies, Sunrise Dam, Western Australia, in Proceedings World Gold 2013 , pp 463-468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Salmon, M Kennedy

Sun Metals Corporation Pty Ltd (SMC), a wholly owned subsidiary of Korea Zinc Co Ltd (KZC) is a company formed to develop, construct and operate a zinc refinery, 11 km south of Townsville in North Queensland. The project opportunity exists because of on-going consumption growth for refined zinc metal, technological, environmental and economic obsolescence of existing zinc processing plants, and a prolonged ædroughtÆ of new zinc processing capacity under construction. The Project will utilise proven technology developed by KZC at the Onsan refinery in Korea. The Townsville Refinery has been designed to be the most environmentally-friendly zinc refinery in the world, and in particular to resolve the issue of secure, long term treatment of the ironbearing content of the zinc raw materials.

Jan 1, 1998

By R H. Sibson

Magmatic and/or hydrothermal fluid systems in island or mountain arcs self-organise to critical states subject to perturbation by changes in the regional stress, which plays a controlling role in the containment of overpressured fluids. Whether the magmatic arc is under compression (eg Andes, northern Honshu) or extension (eg Taupo Volcanic Zone, New Zealand) is a key factor controlling the ease of magmatic or hydrothermal fluid ascent. Abrupt changes in the stress regime have the potential to induce major episodes of fluid redistribution. Large earthquake ruptures along plate boundaries may induce such changes over broad areas, also contributing to fluid redistribution by renewing fault permeability along the causative rupture zone or reactivating distant fault-fracture permeability by shaking from radiated waves. High-resolution geophysical investigations of active arc systems and the subduction thrust interface underlying their fore-arcs reveal repositories of overpressured hydrothermal fluids. In active magmatic arcs under compression such as NE Honshu or Cascadia, there is evidence for a heterogeneous distribution of overpressured hydrothermal fluids in the middle-to-lower crust trapped around the base of the upper crustal seismogenic zone. Investigations of the subduction thrust interface responsible for great (Mw = 8.0) ‘megathrust’ earthquake ruptures has revealed in some instances (Cascadia, SW Japan) the existence of a belt of non-volcanic tremor (NVT) with accompanying slow slip episodes defining the base of the megathrust interface at 40 ± 5 km and 350°C??-??550°C. Aqueous fluid at these depths is likely derived from dehydration reactions accompanying the basalt-eclogite transition in subducted oceanic crust. NVT sequences in the hanging-wall above the interface may be defining migration pathways into the overlying crust.The potential for eruptive episodes in magmatic arcs and redistribution of hydrothermal fluids is assessed in the light of the stress changes that followed the 2011 Mw9.0 Tohoku subduction thrust rupture which extended along strike for over 500 km and down-dip for over 150 km, with maximum slip of c 50 m.

Aug 22, 2011

By M S. Reston

The Tonkolili banded iron formations (BIF), Sierra Leone, host extensive iron ore deposits which are of economic signifi cance to the seaborne iron ore trade. The deposits are dominated by a strategic JORC compliant mineral resource of 11.6 Bt grading 30.1 per cent Fe comprised of primary magnetite mineralisation in the form of a fresh metamorphosed BIF featuring a uniform mineral assemblage of quartz-magnetite ± ferro-silicate minerals. Pilot plant metallurgical test work has demonstrated that the production of a magnetite concentrate is achievable using the established beneficiation techniques of magnetic separation and flotation. The concentrates arehigh-grade, and suitable for blast furnace or direct reduced iron pellet feed. The major challenge facing the development of such magnetite deposits at industry competitive production rates is the significant capital investment required for process plant and associated infrastructure.Two well-developed weathering zones exist within the deposits, and are associated with the progressive development of a tropical weathering profile overprinting the primary BIF. These zones feature a near surface hard indurated duricrust up to 60 m thick, and a soft progressively developed saprolite between duricrust and fresh BIF. These zones have been found to be amenable to producing iron ore products including DSO lump and sinter fines from the duricrust, and concentrate from the saprolite. Mineral resources sufficient to support commercial production of such iron ore products were defined by an intensive exploration program in 2010.African Minerals Limited has developed a three phase production strategy to progressively self fund the development of the Tonkolili strategic magnetite project by:• commencing a Phase I 12 Mt/a DSO operation in Quarter 4 2011,• increasing production in Phase II to 35 Mt/a with the commissioning of a saprolite beneficitation plant and associated infrastructure upgrades, and• developing a 45 Mt/a Phase III operation producing high-grade magnetite concentrate.The comparatively low capital and operating costs of a duricrust DSO lump and sinter fines operation coupled with its proximity to ground surface make it highly attractive for the generation of early cash flow for the Tonkolili project. Revenue from this early production may be used to selffund the subsequent development of phases requiring progressively more significant beneficiation plant and infrastructure.

Jul 11, 2011

By J Millard, K Sexsmith

BHP Billiton Diamonds Inc (BHPB) has been mining kimberlite from several pipes at the Ekati Diamond MineTM located 300 km north of Yellowknife since 1997. Processing of kimberlite produces coarse kimberlite rejects (CKR, 0.5 to 8 mm) and fine tailings (less than 0.5 mm). The CKR are trucked to the Coarse Kimberlite Reject Storage Area (CKRSA) located within the drainage area of the tailings impoundment (Long Lake Containment Facility û LLCF). The coarse rejects are wet when dumped and are expected to freeze as a result of annual average site temperatures of about -10¦C. Seasonal thawing occurs along the exposed edges of the pile. Monitoring of the CKR indicates they have consistently low sulfur concentrations (0.4 per cent) accompanied by high acid neutralisation potentials (78 to 337 kg CaCO3/t). Carbonate concentrations vary from 0.9 per cent to 3.4 per cent. The CKR are therefore not potentially acid generating based on conventional laboratory testing. Monitoring of stagnant pools on the tundra downgradient of the CKRSA has shown that water originating from the pile resembles acid rock drainage (ARD). Water pHs can be less than 4, and sulfate concentrations are typically in the thousands of milligrams per litre. Conventional flowing toe seeps are pH neutral but also have elevated sulfate concentrations. Investigations conducted in the summer of 2002 revealed no evidence of in situ acid generation. Pore water chemistry is probably controlled by oxidation of fine-grained pyrite, neutralisation of acidity by calcium and magnesium carbonates and silicates, and freeze concentration of pore water. The acidity observed in tundra pools downgradient of the CKRSA appears to be a result of leaching and mobilisation of iron under reducing conditions at the CKR-soil contact. Downstream of the CKRSA, reduced iron oxidises and is hydrolysed on contact with the atmosphere causing pH depression. BHPB is applying the findings of this study by constructing facilities containing kimberlite on granite pads. These in turn are placed on frozen ground so that the foundations remain frozen and limits contact of wastes with the acidic soils.

Jan 1, 2003

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

Bureau of Medical Inspection, Broken Hill, New South Wales.INTRODUCTIONFor a considerable time it has be3n realised that the pathological changes produced in human lungs by the inhalation of free silica varied, not only according to the amount of silica inhaled, its particle size and the period during which it was inhaled, but also according to other mineral elements which might be admixed with the fine silica dust and inhaled along with it, or inhaled subsequently to the silica containing dust. It was observed that, in many instances, these admixed dusts tended to inhibit the action of the free silica in causing injury to the lungs, as well as the development of certain complications, whilst in other cases it was felt that certain substances could actually accelerate the tissue damage caused by the silica.A fresh impetus to the problem of the prevention of the development of silicosis was given when, in 1937 and 1939, Denny, Robson and Irwin published papers entitled "The Prevention of Silicosis by Metallic Aluminum." Working at the same time at the Saranac La.boratory, and quite independently, and using a colloidal aluminum hydroxide, Gardner arrived at the same conclusions as Denny, Robson and Irwin, namely, that in experimental animals the development of silicotic changes could be prevented if eithertogether with the silica, or subsequent to its inhalation...

Jan 1, 1946

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

In recent years, due to advances in designing of various magnet assemblies, a wide range of magnetic materials with different properties can be concentrated. Jalal Abad iron ore beneficiation plant, which is located in Iran, Kerman province, is currently producing iron ore concentrate with the capacity of 0.8 Mt/a by having medium intensity magnetic separators (MIMS) with rougher and cleaner stages that finally leads to the production of an iron concentrate with the Fe grade of about 65 per cent. In this plant, the rougher tailings directly goes to the thickener as the final tailings and cleaner tailings feeds to the ball mill for regrinding. Since some hematite particles with weak magnetic properties cannot be recovered from only these two stages of magnetic separation, the obtained tailings from this concentration plant has approximately an iron grade of 25 per cent to 27 per cent. Accordingly, laboratory processing tests were conducted on the obtained representative sample of the final tailings. Based on the experimental results performed on final tailings, a new magnetic drum separator with a specific magnetic assembly was designed that could finally lead to product with iron grade range of 58 per cent to 60 per cent with relative and total weight per cent of 8.6 per cent and 3.86 per cent. Finally, it could be concluded that feeding of magnetite particles to the existing drum separators, due to their high magnetic field intensity, cannot efficiently lead to improvement of the grade of concentrate. Therefore, pilot magnetic separation tests were done on the final concentrate for evaluation of product upgrading probability. Consequently, by increasing another stage of cleaning and by decreasing the magnetic field intensity, the final product grade could be enhanced from 65 per cent to 67 per cent.

Nov 8, 2021

By H Sichani-Teimouri, B N. Noller, J C. Ng, R N. Alsaadi, P L. Breuer, S Shini

Cyanide has been used for over a century worldwide for gold extraction. However, the presence of several metals and metalloids in ore requires greater amount of cyanide for an efficient gold recovery due to their solubilisation in conjunction with gold. The extraction residues are discharged into tailing storage facilities (TSFs) and may cause bird mortality if there is exposure to cyanide-bearing wastewater exceeding the toxic threshold. The toxicity arises from free cyanide released from weak acid dissociable (WAD) cyanide complexes. The International Cyanide Management Code (ICMC) has deemed 50 mg/L of WAD cyanide released into TSFs to be safe for wildlife protection. However, this concentration is based on observations of an apparent lack of toxicity rather than a toxicological approach. The National Industrial Chemicals Notification and Assessment Scheme (NICNAS) identified in 2010 that there is a lack of toxicity data to properly assess the environmental significance of cyanide levels at gold mines. Lack of knowledge for the toxicity of free cyanide and metal cyanide complexes to wildlife led to consider alternative direct assessment techniques for designating safe levels. Whilst toxicity may be assessed by using young chickens with animal ethics approval, the traditional bioassay approach to assess cyanide toxicity is impractical for gold mine TSFs. Bioassays using algal species such as Euglena gracilis, a unicellular alga, are widely used for ecotoxicological studies. A unique feature is that the Euglena gracilis Z cell has plant-like while SMZ cell has animal-like characteristics. The aims of this project are to evaluate the suitability of Euglena gracilis Z and SMZ strains to assess the toxicity of free cyanide and both strong (cobalt) and weak (zinc, copper and nickel) acid dissociable metal-cyanide complexes that may be present in TSFs.CITATION:Noller, B N, Ng, J C, Shini, S, Breuer, P L, Sichani-Teimouri, H and Alsaadi, R N, 2014. Development of a toxicity approach to evaluate free cyanide and metal cyanide complexes in waters associated with gold and other mining, in Proceedings Life-of-Mine 2014 , pp 573–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

By R F. Sandenbergh

Due to environmental considerations, mineral processing plants are increasingly recycling water to decrease the impacts of wastewater on environment and the depletion of fresh water resources. Industrial experience has shown that increasing recycling water in flotation typically negatively impacts the recovery and selectivity, especially in the selective flotation of minerals from complex sulfide ores. The major reason for the reduced selectivity is typically the inadvertent activation of sphalerite or pyrite by the heavy metal ions (HMI) in solution. These HMI are often produced during milling and flotation and absorbed by other minerals. In the normal flotation pH value range (8 - 10), these HMI are often in the form of precipitates or complex ions that may re-appear in solution or become active should conditions favour this. In this paper, microflotation, batch flotation and XPS surface measurement were used to investigate the use of HMI absorbents additions to the pulp to improve flotation selectivity of a complex sulfide ore. It has been demonstrated that HMI removal does improve flotation selectivity by facilitating more effective depression of the sphalerite. Microflotation and XPS surface measurements have shown that HMI absorbents compete with sphalerite to absorb HMI, and thus reduce the surface concentration of HMI on those sulfides. The practical use of HMI absorbents in complex sulfide ore flotation is also discussed.

Jan 1, 2005

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006