Search Documents

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By E. A. Anderson, C. W. Siller, Gerald Edmunds

In the pressurc die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger arid a complcte shutdown of the equipment. All of the zinc alloys used for pressure dir-rnsting today contain approximately 4 per cent of aLUminum, which is more than suffieient to make plunger opcration feasible. The clearancc bet,ween the plunger and its bushing is an important matter. As the space bccomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still uscd in some machines. However, the rate at which the plunger c1earance. increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new matcrinls more: capable of retaining the desired clearance during long periods of use. Today marly die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger. operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the pluriger will operatc for a long time, of course.. The authors have developed a laboratory apparat,us in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clearance area.

Jan 1, 1940

By Gerald Edmunds, C. W. Siller, E. A. Anderson

In the pressurc die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger arid a complcte shutdown of the equipment. All of the zinc alloys used for pressure dir-rnsting today contain approximately 4 per cent of aLUminum, which is more than suffieient to make plunger opcration feasible. The clearancc bet,ween the plunger and its bushing is an important matter. As the space bccomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still uscd in some machines. However, the rate at which the plunger c1earance. increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new matcrinls more: capable of retaining the desired clearance during long periods of use. Today marly die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger. operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the pluriger will operatc for a long time, of course.. The authors have developed a laboratory apparat,us in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clearance area.

Jan 1, 1940

By John D. Sullivan

Leaching of copper ores is a comparatively old art, probably dating back to medieval times. The leaching of mixed oxidized-sulfide ores, however, is modern. The first modern plant leaching mixed ores was at Ajo, Ariz., where commercial operations commenced in 1917. While the ore at Ajo was primarily oxidized there was always some sulfide present. The Inspiration leaching plant, which was put in operation in 1926, may be considered the first plant constructed for the extraction of both sulfide and oxidized copper. The pioneers in leaching mixed ores had a difficult task before them since they had very little fundamental data on the chemical and physical factors of leaching. For the very large amount of painstaking experimental work that was done before building the Ajo and Inspiration leaching plants the reader is referred to the original articles.' For a period of several years the writer worked on problems connected with the chemistry and physics of leaching mixed oxidized-sulfide ores. This paper summarizes the experimental work and discusses various factors involved in leaching ores. It also presents many data heretofore unpublished. Among the new data are those on chrysocolla, pages 518 to 519, inclusive; dioptase, page 519; covellite, page 529; virtually all those on chalcopyrite, pages 531 to 533, inclusive; enargite, page 533; and tetrahedrite and tennantite, pages 534 and 533. The oxidized copper minerals of commercial importance in American ores are azurite, Cu3(OH)2(CO3)2; malachite, Cu2(OH)2CO3; chrysocolla, CuSi03.2H2O; tenorite (or melaconite), CuO; and cuprite, Cu2O. Dioptase, CuSiO3.H2O is less common. Brochantite, CuSO4.3Cu(OH)2, while the chief mineral in the ore at Chuquicamata, is not of major importance in the United States. Metallic copper, while chemically not so, is frequently classed as an oxidized mineral of copper. The most important sulfide minerals are chalcocite, Cu2s; covellite, CuS; bornite, Cu5FeS4; and chalcopyrite, CuFeS2. Less important complex sulfides are enargite,

Jan 1, 1934

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939

By C. G. Fink, E. P. Polushkin

A PART of the material incorporated in this paper was derived from the studies of ancient metal objects examined by the authors from time to time for museums and art collectors, in order to verify the age of the metal. The data thus accumulated during several years were systematically surveyed and supplemented by new material obtained in examination of a set of specimens that had been generously donated by museums for this study. Altogether over 50 pieces were investigated, of which 39 are described in this paper. Every specimen is at least 1500 years old; the majority are considerably older. Exact conditions to which these bronze and copper objects were exposed in the ground are unknown, unfortunately. It is safe to say that exposure conditions did not remain constant during the long period of burial. Although the collection of specimens studied represents a wide variation in location and age of the objects, as well as in the nature and composition of the metals, it was found that fundamental changes in the metal structure were limited to a few typical cases which, therefore, may be considered as more or less general. The authors' chief aim was to study the effect of extremely long periods of corrosion on the structure of bronze and copper. Specimens Studied As the majority of specimens were very small and sometimes had a heavy coat of patina, or crust, which further reduced the amount of metal available for analysis, quantitative chemical analyses were not made. Small detached specimens were not always obtainable and studies had to be made on the statue, or other object, itself. In the description of specimens (Table I), their approximate compositions determined under the microscopc are given. The proportion of tin in bronze containing eutectoid was found by visual estimation of the area occupied by the eutectoid. It was based on the assumption that maximum solubility of tin in copper on moderately slow cooling is 7 to 8 per cent in thin castings and 9 to 10 per cent in heavy castings. When the metal was all

Jan 1, 1936

By Henry Siegmann

HISTORY OF PRODUCTION AND USE In 1899 the consumption of fluorspar in the United States was reported as 16,000 tons. The invention of the open-hearth method of steel manufacture, plus the beginnings of a fluorine chemical industry, pushed consumption of fluorspar to 250,000 tons by 1918. In contrast to these consumption statistics of the past, the most recent statistics available (1972) indicate a total fluorspar usage in the United States of 1.352 million st (Table 15.4D.1). Fluorspar remains the world's cheapest source of fluorine, and its unique properties make the mineral the most desirable fluxing agent for steel refining. The linking of fluorine with carbon in the late 1930s resulted in the production of fluorocarbon, and constant growth in production over the years has formed the backbone of a strong fluorine chemical industry. For example, in 1972 it is estimated that total fluorocarbon production amounted to 2.113 million tons, and that, in this process, over 1.351 million tons of acid-grade fluorspar was consumed. The producers of primary aluminum long have been concerned about the fast dwindling reserves of natural cryolite. They found the solution to their problem by utilizing fluorspar for the manufacture of synthetic cryolite and aluminum fluoride. Nuclear weapons, as well as the growing number of peaceful uses for atomic reactors, constitute a market for uranium hexafluoride. This chemical and chlorine pentafluoride, used as an oxidizer with rocket fuels, are products that are as much a novelty as fluorocarbons were 25 years ago. Judging from past success in the field of fluorine chemistry research, it is safe to assume that the market for these chemicals will grow in the future. Three major industries account for the bulk of the fluorspar consumption: steel refining, fluorine chemical, and primary aluminum production. These industries have had a pattern of fabulous growth in the past, and their future plans point to a continuation of this pattern. It seems logical that the fluorspar usage also should continue its upward trend. Considering the growth of the fluorspar industry since 1899, and the obvious dependence on imports of fluorspar as a raw material, one of the most puzzling aspects of the past has been the apparent lack of coordination between fluorspar production and fluorspar consumption. A few authoritative voices have spoken out concerning the need to expand fluorspar production in order to meet consumption of the future. During World War II, the U.S. Government took positive steps in this direction by authorizing purchases at attractive prices for its "stockpile program." As a consequence, new fluorspar producing facilities were built, not only in

Jan 1, 1976

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947

INTRODUCTION This chapter summarizes porphyry copper deposits within the State of Alaska. Prospecting for porphyry copper-type deposits in Alaska germinated during the 1940's, grew slowly during the '50's, boomed during the '60's, and matured in the '70's. Although large expenditures have been made in the search for porphyry-type deposits, most accrued data lies dormant in company files. However, an adequate base exists in the literature for a general synthesis of areas that contain porphyry prospects. To simplify the summary, porphyry molybdenum deposits as defined by Clark (1972) are omitted. Description of deposits in their geologic setting permits some correlations between deposit characteristics and crustal environment. These correlations allow speculation about the genesis of the deposits. The summary also attempts to group deposits on the basis of general mineralogic characteristics because diorite model deposits are separated from quartz phenocryst-bearing hosts. Data presented in this chapter summarize observations by the author, published descriptions of specific areas and deposits as noted in the bibliography, and comments by various government geologists. E. M. MacKevett, Jr., D. H. Richter, and H. C. Berg of the US Geological Survey have been particularly helpful. Because few comprehensive descriptions of individual porphyry copper deposits exist for this area, much of the data presented is new to the literature. Details of structure, isotopic geochemistry, and petro- genesis for individual deposits are largely lacking and even the general geology of some belts is not well understood. Details on petrography of Alaskan porphyry copper occurrences are inadequate for construction of ternary diagrams (e.g., Figs. 36a, b, pp. 103, 104, for the northern Cordilleran orogen). Petrographic descriptions summarized in the text are largely from published descriptions whose sources are cited. Porphyry copper-type deposits in Alaska include deposits with pervasive pyrite that contain disseminated copper (but not necessarily coproduct molybdenum). Available data preclude differentiating the deposits by size. No Alaskan porphyry copper deposit is now in production but this is believed to be, in part, a function of economics. In some cases available geologic information is in- adequate for classifying deposits. Some de- posits included with porphyry copper may, with further exploration, be demonstrated to be some other genetic type. Alaska has three distinct porphyry copper provinces: the Hogatza plutonic belt, the Continental Margin belt, and the Interior belt. Each belt contains deposits with characteristic geologic features distinct from those of other belts. Fig. 24 shows the continental margin belt to extend inland from

Jan 1, 1978

By J. B. Newkirk, A. H. Geisler

Certain of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some perrnanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems oA&apos;er for study over the usual in which an intermetallic compound is formed are many: 1. Since the precipitate has the same crystal strutture as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be ex. petted to have the same orientation. 3, Small &,registry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from 0 to 100 pet* thus permitting wide freedom for the study of the effect of cornposition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1&apos;2 The two have the same <Jo parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for CU-Ni-CO alloys because of the similarity in constitution but this had not been demonstrated. The Present investigation was conducted on a CU-Ni-CO alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established, however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system Was chosen for a comprehensive investiga-

Jan 1, 1949

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By J. B. Newkirk, A. H. Geisler

INTRODUCTION CERTAIN of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some permanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems offer for study over the usual in which an intermetallic compound is formed are many: I. Since the precipitate has the same crystal structure as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be expected to have the same orientation. 3. Small disregistry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from o to 100 pct* thus permitting wide freedom for the study of the effect of composition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1,2 The two have the same [ao] parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for Cu-Ni-Co alloys because of the similarity in constitution but this had not been demonstrated. The present investigation was conducted on a Cu-Ni-Co alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established 4,5 however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system was chosen for a comprehensive investiga-

Jan 1, 1948

By Wm. R. Dotson

Forty years ago the atom was split and the Age of Fission dawned. Uranium was the element used in this earth-shaking accomplishment. Thitherto almost unknown to the man in the street, uranium soon became widely and persistently sought. And the quest for this unique material is not likely to diminish during this century. To find is one thing; to own is another. Who owns uranium in the ground? Where no mineral rights in the land have been severed by devise, grant, reservation or lease, the uranium belongs to the fee simple owner of the land. But where there has been a conveyance or reservation of all or part of the "minerals", determining WHAT a substance is has been the traditional way of determining WHO owns it. What, then, is this element called uranium? The 1907 edition of Watts Dictionary of Chemistry calls it "a lustrous, hard, silver-white metal". Of nature&apos;s three prime divisions it falls within the embrace of the mineral kingdom - substances neither animal nor vegetable. In its natural state uranium always is combined with other elements or substances in the form of an ore mineral. May we, then, put to rest any doubt or question as to the nature of uranium and classify it for all purposes, including that of ownership, as mineral? Not quite! That self-same logic would find oil and gas primly ensconced in the animal or vegetable kingdom. Technically, oil and gas are not minerals but legally they have been classified as such. Why? The Supreme Court of Tennessee sought the answer in 1897 in the case of Murray v. Allard, 43 S.W. 355. After citing authorities pro and con, and while admitting their origin to be "decomposition of marine or vegetable organises" that court firmly concluded that since they were obtained by a form of mining, oil and gas were minerals. From the above example two elementary truths emerge. First, for purposes of ownership, uranium is and will be whatever the courts say it is. Secondly, the courts historically and currently favor a practical rather than technical test to determine the "mineral" character of a substance. So now we turn to the jurisprudence for enlightenment and definition. EARLY CASES ALLOT URANIUM TO MINERAL OWNERS Two early cases involving the ownership of uranium followed what had been well-settled mineral within the meaning of the conveyances involved, confirming ownership in the mineral owners. In 1956 the U. S. District Court for New Mexico in the case of New Mexico and Arizona Land Company v. Elkins, 137 F. Supp. 767, appeal dism&apos;d 239 F.2d 645 (10th Cir. 1956), found that a 1946 deed reservation of "all oil, gas and minerals underlying or appurtenant to said lands" included uranium and thorium. The court reasoned that uranium and thorium, being minerals within the scientific, geological and practical meaning of the term, would certainly constitute minerals within the purview of the reservation. While agreeing that uranium and thorium were "minerals", defendants argued that at the tine of execution of the conveyance it could not have been the intention of the parties to reserve them because they had no commercial value in the locality and were, in fact, not known to there exist until their later discovery in 1950. The court re¬jected, as a matter of law, this "lack of knowledge" theory citing the Supreme Court of Kentucky holding in Maynard v. McHenry, 113 S.W. 2d 13, that: "The mere fact that a particular mineral has not been discovered in the vicinity of the land conveyed or is unknown at the time the deed is executed rules of construction and held that uranium was a does not alter the rule . . ." that a grant or exception of "mineral" in a deed includes all mineral substances which can be taken from the land unless restrictive language is used indicating that the parties contemplated something less general than all substances legally cognizable as minerals. Further, argued the defendants, the only feasible mining procedure for such substances was open pit or strip mining, which would destroy the value of the land for grazing or agriculture. Finding that the language of the reservation was clear and unambiguous, the court would not permit the admission of extrinsic evidence as to mining procedures required. Elkins is the first uranium case construing the granting clause involved. In 1958 the Texas Court of Civil Appeals at San Antonio, in Cain v. Neuman, 316 S.W. 2d 915, no writ, held that a 1918 lease conveying "all of the oil, gas, coal and other minerals in and under" the land involved covered uranium. The lease provided a royalty of 1/10th on "other minerals." "We find no Texas precedent which discusses uranium," said the court, "but the usual arguments that uranium is not embraced within a lease are that the ejusden generis rule excludes uranium from the meaning of the lease

Jan 1, 1979

By G. Borelius

ABOUT the turn of the century, Gibbs&apos; thermo-dynamic theory of heterogeneous equilibrium, on the one hand, and the experimental methods of thermal and microscopic analysis, on the other, gave to the physical metallurgist his first scientific tool, the equilibrium diagram. The classical equilibrium diagram of a binary alloy system shows the boundaries between ranges of homogeneous and heterogeneous equilibrium in their dependence of concentration and temperature. A homogeneous solid sohtion which on cooling passes such a boundary is assumed to precipitate, forming a mixture of two phases with different concentrations. The equilibriunl diagram and the equilibrium theory, however, give no information about the time scheme of the process or the intermediate states passed during precipitation. For this reason it satisfies neither the practical need of the metallurgist nor the curiosity of the physicist. As a matter of fact, in the heat treatment of alloys for technical use the objective very seldom is the equilibrium state. Thus good mechanical properties of construction material are connected, for the most part, with some intermediate state. As these intermediate states are thermodynamically unstable, there is, from a theoretical point of view, always to be expected a decay of the good properties with time; and it is a matter also of practical interest to know whether this natural life time of a material is of the order of, say, ten or thousands of years. Thus, for many reasons, there is a current demand to complete our knowledge of equilibrium through knowledge of the kinetics of the precipitation phenomena. From the point of view of the physicist, the most interesting question in this case is whether there are any general laws governing the kinetics. According to a generally accepted view, precipitation is ruled by two more or less independent phenomena, the formation of nuclei of a new phase and the growth of these nuclei. It is also commonly accepted that there is a tendency for the velocity of growth to increase with increasing temperature because of the increasing mobility of the atoms. There is also a tendency for the velocity of growth to decrease in the neighborhood of the two-phase boundaries. So far, however, very little is known quantitatively about this fundamental phenomenon in the case of solid metallic systems. In our laboratory attention has been directed especially toward the nucleation phenomena, and a series of measurements have been carried out with the guidance of a work- ing hypothesis (based on experiences from previous work on order-disorder transformations in alloys) about the influence on the nucleation of thermo-dynamic potential barriers. However, before discussing the experiments, the theoretical ideas will be considered. In a binary solid solution the arrangement of atoms on the lattice points approaches with increasing temperature a state of full randomness, as illustrated by the ball model of Fig. 1, that might represent a [111] plane of a face-centered alloy with 30 pct "black" and 70 pct "white" atoms. In reality the atoms are changing places continually with their neighbors so that the picture should rightly have been a moving one. On account of this thermal motion the concentration of black atoms within a certain group of, say, a hundred or a thousand lattice points fluctuates with time around the bulk concentration of 30 pct in a manner governed by statistical laws. With decreasing temperature two independent changes in this state grow more and more important. First, the mobility of the atoms decreases, and second, the forces between the atoms will have an increased influence on the fluctuations. In alloys with a tendency for precipitation, which are the concern of this lecture, the distribution function of concentration fluctuations will broaden, so that the relative probability of great local variations from the bulk concentration increases. Fig. 2 gives an example of such a fluctuation. When the alloy is supercooled below the solubility limit into the range of two-phase equilibrium, the fluctuations will now and then at some point give rise to a state that resembles the equilibrium state and thus will form a stable nucleus that is capable of growing by diffusion processes. In discussions with colleagues and in the literature, I have often encountered the idea that three or four atoms of the dissolved metal could form a nucleus of the new phase. A look at the ball model might be enough to indicate that this cannot be true. If it were true, there should be nothing but nuclei, whereas we know from experiment that nucleation must be a rather rare occurrence. In fact we have, as will be mentioned later, certain reasons to believe that the nuclei are formed by fluctuations containing some hundreds of atoms, which should be the order of the number of black balls in the fluctuating group of the figure, if it were extended into three dimensions. As a working hypothesis we have assumed that the fluctuations producing nuclei, though large and rare, still are ruled by the distribution laws of fluctuations of the supercooled solid solution in its initial state. Thus the probability of nucleation will be connected to the thermodynamic properties of the solid

Jan 1, 1952

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and (2) cover the various aspects of the major raw materials used to make glass. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks used in glassmaking, the reader is referred to chapters in the commodity section of this book. Glass Industry Statistics Glass manufacture in the United States can be divided into three major product classifications as follows: 1) Glass containers 2) Pressed and blown glass 3) Flat glass Glass containers include bottles and jars for the packaging of food and beverages, as well as drugs, chemicals, and cosmetics. Pressed and blown glass includes table, kitchen, art and novelty ware, lighting and electronic glassware, and fiber glass. Flat glass covers sheet or window glass, plate, laminated, and safety glass. The US Department of Commerce statistics, as recorded in the 1977 Census of Manufacturers, compares the dollar value of glass shipments for each product category. These statistics are shown in Table 1 (Anon., 1980) and are self-explanatory. A comparison of the tonnage output in each product classification is difficult, as production data is reported in "gross" for glass containers, "pounds" for fiber glass, "pieces" for glassware, [ ] and "square feet" for flat glass. In the case of glass containers, an average "pounds per gross" factor can be applied to the total production figures reported in thousands of gross in Bureau of Census industrial reports. Table 2 presents the calculated annual production tonnage for glass containers for the years 1974-1979. Except for 1979, there was a yearly increase in production. The tonnage figures of Table 2 are further influenced by decreasing weight per gross which has occurred in the glass container industry since 1975. This reflects the gradual shift to lighter weight containers for beverages. Other segments of the glass industry have experienced growth, but the figures in tons are not published information. Fiber glass growth has been influenced by the heavy demand for insulation as part of energy conservation efforts on a national basis. The production of flat glass by the float process has continued to grow with several new plants entering production. All portions of the glass industry experienced the effects of the general economic decline of 1979-1980, but the outlook for the future is bright. Batch Materials For Glass Use Materials and Function Soda-lime-silica glass represents the largest proportion of glass manufactured for commercial use. It is produced by the fluxing and

Jan 1, 1983

By P. R. Sperry, A. P. Beck

It has been shown1 that in poly-crystalline strips of high purity aluminum with a fairly random orientation distribution, grain growth progresses gradually until the average grain diameter reaches a value approximately equal to the strip thickness. Recent work at this laboratory led to the realization that grain growth might be impeded to a considerable extent in the presence of a sharply defined texture, where orientation differences between neighboring grains are small. In order to investigate this effect the following experiment was carried out with the same lot of high purity aluminum previously used for grain growth studies in randomly oriented material.&apos; Very large grain size was developed by grain growth at 650°C in specimens of 0.200 in. thickness. These specimens were then rolled to a thickness of 0.050 in. or 1.25 mm—a reduction of 75 pct. In the rolled strip each large grain corresponded to an elongated area easily identified by etching. After annealing for 1 to 25 min at 600°C and re-etching, these elongated areas were again recognizable. Within each area, corresponding to a single large grain before annealing, there formed by recrystallization a multitude of new grains with a fairly well developed preferred orientation. The orientation and the size of the new grains formed in areas corresponding to different large grains, varied widely depending on the orientation of the parent grains with respect to the rolling direction and the plane of rolling. Many areas were found where the average grain size was considerably smaller than the specimen thickness. Such an area occurred in a specimen cut in half before annealing. One half, containing a portion of the area in question, was annealed 1 min at 600°C, the other half, with the remaining portion of this area, for 25 min at the same tempera-Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951