Search Documents

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

ALBERT SAUVEUR, Chairman. A. A. STEVENSON, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, William Kelly, J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. J. E. Johnson, Jr., The innovation of a special meeting under the auspices of the Iron and Steel Committee was well justified, if we accept as a criterion the number of papers presented at the meeting held on Oct. 16 and 17 in New York and the attendance at that meeting. Twenty-four papers were read, and most of these were widely discussed orally, while doubtless the written discussions will be even larger in extent. Discussions will be received up to Dec. 1, 1913. The attendance at the meeting of 106 members and 75 guests is an evidence of the wide anti growing interest in the Institute of men interested chiefly in iron and steel. It is especially interesting to note this large attendance at a meeting where very little of a social nature was introduced into the program. An informal dinner for the men at the Engineers' Club closed the meeting. At this dinner were present about 70 members and guests. One of the Vice-Chairmen and the Secretary of the new Committee on Petroleum and Gas told of the important plans in prospect of that Committee. Brief impromptu speeches by a considerable number of the members and guests were enjoyed. Professor Marburg reiterated his previous assertion that he believed that the Institute and the American Society for Testing Materials, as well as some of the other technical societies, were all fighting for one good cause; that there was room in the field for all of these societies with their various points of view; and that they should march shoulder to shoulder. The success of this dinner was due largely to the efforts of Mr. Johnson who had the affair in charge.

Jan 11, 1913

By R. L. Sebastian

ALUMINUM'S war history is the record of a successful race to expand facilities fast enough to meet the multiple increases in military requirements, principally for aircraft. From the beginning of the war program in 1940 through 1942, requirements estimates were repeatedly lifted to new high levels, and plans for increasing capacity had to be constantly revised. In 1943, basic metal supply caught up with and exceeded requirements, and by 1944, the surplus of primary production was large enough to force reduction in output and plant closings. In the past two years, ingot capacity has been ample, though periodic critical shortages have been experienced for a few fabricated shapes as a result of sudden shifts in demand. And now with all controls lifted we are faced with surplus capacity, surplus stocks, and surplus scrap. In 1938 the Aluminum Co. of America was the only U. S. producer of primary

Jan 1, 1946

By S. P. Kinney, C. E. Wood, T. L. Joseph

In connection with its investigations of the blast-furnace process, the Bureau of Mines, in cooperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferroman-ganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the cooperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests. The Aluminum Co. of America was interested in knowing the practicability of smelting a charge of bauxite, iron ore, and limestone, of proportions that would produce slag of the following composition: A1203, 47 to 48 per cent.; CaO, 41 to 42 per cent.; SiO2,4 to 5 per cent.; TiO2, 2 to 3 per cent.; FeO, 1 percent., and MgO, 1.8 percent. In addition to determining whether it was feasible to operate a blast furnace on slag approaching the composition given above, a quantity of slag was needed for a series of experiments that would show the relative ease and cost of extracting alumina from slag which could be made in the blast furnace, as compared to extracting it from raw bauxite. The value of the slag as a raw material

By W. Tovote

This paper is based upon 12 years' experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coördinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, due to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining states. Possible Systems of Classification By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that are most striking in their uniformity. 1. The "Desert province," extending roughly from Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and down into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows. 2. The "Yavapai schist" province, similar to the one first mentioned, consists of metamorphosed basic and semi-basic rocks. It lies in northern

Jan 1, 1920

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating tables of modern design on unclassified feeds of —Vz in. particle sizes, including tests on high-sulphur coals. THE increased economic necessity of cleaning the small sizes of coal has forced wide attention upon various methods or processes being used. Although numerous cleaning plants in the past have been cleaning coal smaller than Vz or % in., the large quantities of higher ash fines being produced by mechanical mining and the need for cleaner coal under competitive market conditions have brought about many new installations of fine-coal cleaning plants. Of various methods used, one of the more popular types is the wet concentrating table. Approximately 525 tables have been installed in the United States in the past four years of which 320 have been installed in 20, large new plants. There are now probably 1600 tables of all types in existence in this country for cleaning coal. The purpose of this paper is to describe the cleaning of fine coal by wet concentrating tables. Its scope is confined to a discussion of the theory of tabling and some of the factors entering into tabling action, a description of the Deister SuperDuty diagonal-deck coal table and a discussion of the results of tabling various fine sizes of coals. Al- though tables have been used for cleaning coal as coarse as 2 in. and favorable results are reported, this paper is limited to reporting on the results of cleaning coal fines from 1/2 in. down. Also, although it is well known that the performance of tables is even superior under classified or closely sized feed conditions, this paper concerns itself with the results achieved by tabling unclassified feeds. History of Wet Concentrating Tables The wet concentration of minerals by some form of tabling is quite old, starting originally from fixed, smooth surfaced, tilted boards taking advantage of the laminar flow of liquid films and the separation of minerals according to specific gravity. This was followed by the development of rough deck surfaces

Jan 1, 1951

By James Terry Duce

The gross production on the Island of Sahreirl during 1944 was approximately 6,700,000 U. S. bbl. No additional wells were drilled in the field during the year, but a number that were plugged off during the critical days of the war were brought back on production. This work is continuing. The construction of the extension of the refining plant was continued during the year and the new crude still was started in November. In Arabia, the production for the year 1940 was 5,074,838 U. S. bbl. Four wells were completed in Dammam field and all were commercial producers. Production for 1941 was 4,310,110 U. S. bbl. Seven more commercial producing wells were completed in Dammam field, and Well No. I at Abqaiq was complcted at 6180 ft. and was also a commercial producer. In 1942 production was 4,530,492 U. S. bbl. Abqaiq No. 2 was drilled to 5785 ft. but was left standing because of mechanical difficulty. The 1943 production was 4,868,- 184 with one well drilled, Abqaiq No. 3 completed at 6488 ft. and a commercial producer. Total production in Arabia for the year 1944 was around 7,800,000 U. S. bbl. and at the close of the year was running at approximately 40,000 bbl. per day. The small refinery, built in 1939, at Ras Tanura was in operation in the fall and a new refinery is being constructed. Only three wells were completed during the year—the El Jauf well in Northern Arabia (completed at 10,974 ft.) which did not bring in commercial production and Wells No. 4 (completed at 6270 ft.) and No. 5 at Abqaiq (completed at 6751 ft.), which were brought in as substantial commercial producers. Production for the year was entirely from the Dammam field. In this field, some of the wells that had been plugged off early in the war were brought back in production and this work is continuing. At the close of the year, one well was drilling in the Abqaiq field and an additional well was drilling at Qatif, the latter being a wildcat. Neither of the wells in question had reached producing horizons on the first of January.

Jan 1, 1945

By D. Turnbull, J. H. Hollomon, J. C. Fisher

The concepts of nucleation and of growth have adequately described the isothermal phase transformations to which they have been applied.ls2 However, these concepts have not yet been used successfully to describe the kinetics of a number of transformations that are not observed to take place isothermally. A typical reaction of this type is the austenite to martensite transformation in steels, for which the new phase appears only during cooling of the parent phase. If the cooling is interrupted, transformation ceases; yet had the cooling continued, transformation would also have continued. Nuclei of a new phase do not leap into existence all at once by the simultaneous cooperation of a large number of atoms or molecules of the parent phase; rather they are formed at finite rates by gaining or losing atoms one at a time from the surrounding materiaL3,4 Further thermo-dynamic considerations require a finite concentration of small transitory nuclei of all unstable phases to exist at equilibrium in a stable phase.= For steel in particular, nuclei of ferrite (a iron) exist at equilibrium in austenite (y iron) at temperatures where austenite is the stable phase. If a high-temperature phase a be cooled sufficiently rapidly from temperature TI above the a-ß equilibrium temperature To, to temperature T-1 below To where ß is the stable phase, the equilibrium distribution of ß nuclei corresponding to the high temperature will be retained. There are two limiting possibilities of particular interest: I. The steady state rate of nucleation of ß may be appreciable at T_1, and may require a concentration of sub-critical nuclei exceeding that retained from the high temperature. Time will be required then for the concentration of nuclei to build up to the steady state value, and an induction period will be observed during which the rate of nucleation will increase to the steady state value. 2. The steady state rate of nucleation of ß may be negligible at T-l, while the critical size for continuous growth of ß nuclei, which decreases with increased subcooling of the a phase, may reach a value so small that some. of the retained high-temperature nu-

Jan 1, 1949

By Benj. E. Shackelford

THE present paper is concerned with typical temperature values experienced in lamp-filament measurements as made on regular factory and engineering products. It deals with the relations existing between temperature, efficiency, lamp size, and life of incandescent lamps, insofar as they affect the rating of the product and its use by the individual consumer. The temperatures measured lie in that range covered only by the general method of radiation pyrometry, as opposed to direct methods used under contact conditions. The range of temperatures ordinarily experienced extends from about 2125° K., for the now almost extinct carbon-filament lamp, to 3200° K. for the comparatively new tungsten-filament motion-picture lamp. Most of the more common sizes of tungsten lamps have temperatures ranging from 2500 to 3000° K. Because of the high temperatures involved and the relatively small area of the sources used, we are practically restricted to two methods of measurement, both of which depend on the light radiated front the filament. The first and more usual method is that of the Morse pyrometer, dependent on the variation in temperature of the amount of light of a given color range yielded by the filament. In this case, the measured temperature is that of a small part of the incandescent body, that is, the part which is focused on the comparison filament. The second method, known usually in this country as that of "color match" and in England as "color-identity" is based on the color of the total light yielded by the filament, the comparison being facilitated by the use of an ordinary photometer- head. A more definite idea of the temperatures involved in the case of filaments of various vacuum and gas-filled lamps, is given by Fig. 1. The size of the lamp, in watts, is plotted along the horizontal axis and the temperature of the filament is plotted along the vertical axis. The lamps concerned are regular product, rated for 1000 hr. life. The temperature values for the old 16-candlepower carbon lamp and the new motion-picture lamp are shown by the cross and circle respectively.

Jan 9, 1919

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating tables of modern design on unclassified feeds of —Vz in. particle sizes, including tests on high-sulphur coals. THE increased economic necessity of cleaning the small sizes of coal has forced wide attention upon various methods or processes being used. Although numerous cleaning plants in the past have been cleaning coal smaller than Vz or % in., the large quantities of higher ash fines being produced by mechanical mining and the need for cleaner coal under competitive market conditions have brought about many new installations of fine-coal cleaning plants. Of various methods used, one of the more popular types is the wet concentrating table. Approximately 525 tables have been installed in the United States in the past four years of which 320 have been installed in 20, large new plants. There are now probably 1600 tables of all types in existence in this country for cleaning coal. The purpose of this paper is to describe the cleaning of fine coal by wet concentrating tables. Its scope is confined to a discussion of the theory of tabling and some of the factors entering into tabling action, a description of the Deister SuperDuty diagonal-deck coal table and a discussion of the results of tabling various fine sizes of coals. Al- though tables have been used for cleaning coal as coarse as 2 in. and favorable results are reported, this paper is limited to reporting on the results of cleaning coal fines from 1/2 in. down. Also, although it is well known that the performance of tables is even superior under classified or closely sized feed conditions, this paper concerns itself with the results achieved by tabling unclassified feeds. History of Wet Concentrating Tables The wet concentration of minerals by some form of tabling is quite old, starting originally from fixed, smooth surfaced, tilted boards taking advantage of the laminar flow of liquid films and the separation of minerals according to specific gravity. This was followed by the development of rough deck surfaces

Jan 1, 1951

Butte Meeting. It is expected that the technical program of the Butte meeting will be a sufficient attraction to draw to that point every member who can possibly get away long enough to attend. Attention is particularly called to the papers already sent in by the Committee on Precious and Base Metals, and the papers which they are undertaking to secure for the meeting, as published on pp. ix and x. In addition to these papers, and in addition to those published in this Bulletin, the office of the Institute already has in hand several papers, which will be published at an early date, and presented in abstract and discussed at the meeting. Of the discussion of these papers a special feature is being made. Therefore, let every member come to Butte who can do so. A meeting of the Board of Directors of the Institute will also be held at Butte. In the May Bulletin, we stated for the information of members the railway excursion rates for two suggested tours in connection with the meeting, which included Glacier Park before the meeting and Yellowstone after it. The itineraries there given and rates quoted were planned and offered by the railway agent bureaus in New York. Circulars have been sent to the members of the Institute by A. E. Vaughan & Co., a tourist trip agency of New York City, containing details of tours nearly identical with those outlined in the Bulletin, and quoting rates covering, the expenses of the whole trip. Members can easily compare these rates with the rates offered by the railroads, and published in the last Bulletin. In order that no misapprehension may exist, the statement is here made that the Institute and its officers have no connection whatever with Vaughan & Co.'s proposals and that any such tours will be strictly personal matters between said company and the members of the Institute who take them. Nevertheless, the Board of Directors calls to the attention of members the circumstance that tours such as these will afford an opportunity for members to travel together to the meeting.

Jan 6, 1913

By Joseph E. Pouge

For the purposes of this analysis it is assumed that the petroleum industry has undergone a basic economic change whereby the degree of competition present in its operation is reduced by the collective control of production brought about by statme-directed proration. Formerly freely competitive in all its parts, the industry is now fully competitive only in its marketing, its manufacturing and transportation, its search for new oil supplies, its drilling operations (with some qualifications), and its capital movements. The practical problem before the industry in its new status is the maintenance of equilibrium, with planned control of crude-oil production (proration) substituted for competition and price as the regulatory mechanism at one point in the supply-demand system. It is further assumed that proration has become so firmly established in the legal and operating framework of the business that it may be looked upon as an institution. The purpose of this paper is to call attention to the effect of unregulated drilling upon the orderly functioning of proration. Economic Structure of Petroleum Industry The economic structure of the petroleum industry, under the current form of proration, may be visualized, in simplified form, as shown in Fig. 1. This diagram is designed to indicate the existing mechanism whereby supply and demand are equated. Demand is created largely by conditions external to the oil business, whereas supply is conditioned by a series of stages incidental to the discovery, development and production of a resource. The time elements involved in changes in demand and supply are of an entirely different order, the demand factor being much more flexible and "quicker" than the supply factors. It should be observed, also, that the position of price, formerly between "demand" and "supply," has been moved to a sidewise location where it still affects demand but influences current supply only through its bearing upon proration, drilling and search. Proration has been substituted for price as a throttle at the well head, but at this point only. The mechanism now works in this fashion: a declining price stimulates demand and the

Jan 1, 1936

GEORGE S. RICE (written discussion *).-An interesting and important question arose during the coal famine of last winter as to whether the development of new mines should be discouraged on account of the need of labor for the necessary construction and development work at a time of scarcity of labor, more especially as there was an apparent overcapacity of existing mines. The question was referred to the author for his comments, which led to the study of the statistics. The essential results of this study are indicated on the accompanying chart, which illustrates, among other things, the increase in production or consumption, and the estimated maximum production capacity of the bituminous and sub-bituminous mines of the United States. The curves shown are based on data published in the "Mineral Resources" of the United States Geological Survey, and cover the period from 1900 to 1916 inclusive. The following curves have been drawn from the data secured: 1. Average number of days that the mines worked. 2. Yearly total production of bituminous and sub-bituminous mines. 2a. Yearly production of machine-mined coal. 3. Average annual production, equivalent to consumption, for a period of 17 years. 4. Number of coal mine employees each year. 5. Estimated capacity of mines, on basis of 300 working clays in the year. 6. Estimated drop in capacity if no new mines are opened. Considering these curves and the data from which they were constructed: It will be noted that the average number of days the miners worked varied from 193 in 1908 to 234 in 1900, the average being 217. The causes for so many idle days out of the possible total number of working days in the year are well known, namely: (a) Lack of business; (b) lack of cars. Taking the country as a whole, (a) is the important factor, which might otherwise be expressed as being an excess of productive capacity. The yearly production of the mines, which is practically synonymous with consumption, has shown a steady increase, with a few set-backs. An average line has been struck which indicates that the average annual increase of production has been 18 million short tons (16,330,000 metric tons).

Jan 5, 1918

By Joseph E. Pouge

For the purposes of this analysis it is assumed that the petroleum industry has undergone a basic economic change whereby the degree of competition present in its operation is reduced by the collective control of production brought about by statme-directed proration. Formerly freely competitive in all its parts, the industry is now fully competitive only in its marketing, its manufacturing and transportation, its search for new oil supplies, its drilling operations (with some qualifications), and its capital movements. The practical problem before the industry in its new status is the maintenance of equilibrium, with planned control of crude-oil production (proration) substituted for competition and price as the regulatory mechanism at one point in the supply-demand system. It is further assumed that proration has become so firmly established in the legal and operating framework of the business that it may be looked upon as an institution. The purpose of this paper is to call attention to the effect of unregulated drilling upon the orderly functioning of proration. Economic Structure of Petroleum Industry The economic structure of the petroleum industry, under the current form of proration, may be visualized, in simplified form, as shown in Fig. 1. This diagram is designed to indicate the existing mechanism whereby supply and demand are equated. Demand is created largely by conditions external to the oil business, whereas supply is conditioned by a series of stages incidental to the discovery, development and production of a resource. The time elements involved in changes in demand and supply are of an entirely different order, the demand factor being much more flexible and "quicker" than the supply factors. It should be observed, also, that the position of price, formerly between "demand" and "supply," has been moved to a sidewise location where it still affects demand but influences current supply only through its bearing upon proration, drilling and search. Proration has been substituted for price as a throttle at the well head, but at this point only. The mechanism now works in this fashion: a declining price stimulates demand and the

Jan 1, 1936

By P. R. Martin, R. B. Kelly

Drilling in Central Texas during 1933 was confined, for the most part, to the search for new serpentine plugs. Bastrop County led in this particular activity, with 50 completions during the 12 months' period, 12 of which were productive. Only one new field was opened in Central Texas during the year, it being known as "Hilbig" (Bastrop County) and was discovered by the Humble Oil & Refining Co. The finding of commercial production in the serpentine at 2500 ft. led to further search in this and surrounding counties, but without success. Bexar County actually provided the greatest amount of drilling but the activity was limited to shallow development from 400 to 2000 ft. The Edwards limestone pay, which has been such a factor in past years, received but slight attention during 1933. Unsuccessful exploration was carried on in Lee and Burleson counties. With the exception of Freestone County, the Woodbine sand area was given even less consideration. This county, because of its close proximity to Anderson and Leon counties, saw a very active leasing campaign and several important tests drilled. In Central Texas, 252 wells were completed in 1933, and of this number 52, or 21 per cent, were productive. Hilbig Field The discovery well, Humble Oil & Refining Company's Annie Hassler No. 1, was completed Feb. 16, 1933, for an initial production of 65 bbl. the first hour, through tubing and 1/2-in. choke. The production was found in serpentine at 2468 ft. and tested 37.2" A.P.I. gravity. Twelve producing wells were drilled during the year and served to indicate that not more than 300 acres would comprise the entire field. Daily production at the end of the year was 775 bbl., although the field potential was 18,240 bbl. daily through 1-in. choke. The field adapts itself to pressure maintenance, and this scientific handling is being undertaken by the Humble Oil & Refining Co. through one injection well. It is the only area in the district where work of this nature is under way. Proration of Oil The more stringent application of proration in 1933 did not affect materially the producing fields in Central Texas. This is accounted for

Jan 1, 1934

By W. R. Ingalls

THE manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been clone chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the reverberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Canyon City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose.

Jan 9, 1917

By M. T. Hepworth, R. Schuhmann

Hydrogen solubility measurements were made on a series of Ti-O alloys, and a portion of the 800°C isotherm for the Ti-O-H system was determined. Activities of oxygen and titanium were calculated from the experimentally measured activities of hydrogen, using ternary Gibbs-Duhem integrations. The data were extrapolated to obtain thermo-dynamic properties of binary Ti-O solutions. The thermodynamic properties of a Ti-0 solid solutions thus determined were compared with properties predicted from interstitial models. The Gibbs-Duhem equation, long used to calculate activities in binary systems, has been extended. recently to ternary systems.1"3 When the activity of one component in a ternary system is known as a function of composition, the activities of the other two components can be calculated from that of the first by an integration procedure, provided certain restrictions are observed on the path of integration. Often the activity of one component in a ternary system can be measured readily, while the activities of the other two components are difficult to measure. Gibbs-Duhem calculations are especially applicable to such systems. The further possibility arises of developing a new and indirect approach to activity measurement in binary systems. The proposed new method for binary systems consists of adding varying amounts of a third component whose thermodynamic behavior is easily measured. The activity of this added component is determined experimentally as a function of composition. Then the activities of the two components of the original binary system are calculated by Gibbs-Duhem integrations and extrapolations. For the work to be described in this paper, the Ti-0-H system was selected as a promising system for evaluating this approach. Investigations of the Ti-H system have shown that the activity of hydrogen can be measured precisely with little difficulty. Pure titanium transforms from a low-temperature a form (hcp) to a higher-temperature /3 firm (bcc) at 882.5"~ The phase transformation occurs in a temperature range where hydrogen pressures are easily measured. Also, the diffusivity of hydrogen at temperatures above 600" or 700"~ is large enough that equilibrium can be reached within a reasonable time.

Jan 1, 1962

By J. G. Hall

Introduction When one thinks about world metal economics today, it seems to me he must go beyond the traditional factors such as exploration, discovery, economic feasibility of development, management, labor, and the application of technology. These elements have been and will continue to be very important, of course, in making available the resources that experts believe the world will require during the remainder of this century. There are, however, some new forces as well as new or different emphasis on some of the old factors that could materially affect the development of the world metal mining industries. For example, in my own company two of the most significant considerations affecting our economics today have to do with foreign political decisions and with environmental concerns here in the U. S. -both of which play a far more significant role in our economic considerations than they did as recently as 10 years ago. After a brief look at some historical data and some projections of probable future demands for the world's major metals, I shall then identify and comment upon some of the factors that I believe will have an increasing impact on the future of the economics of our industries. I do not have any magic solutions to the problems we will face; nevertheless, we in the mining industries of the world are going to have to cope with these matters and find satisfactory answers to the problems they will create. The Past Although the age in which we live has been described as the atomic age, the space age and the computer age, we are, in fact, living in a metals age, and we have lived in a metals age for a very long time. The discovery of copper smelting, for example, is placed at about 4000 B.C. Gold was used in a primitive way before that. Other metals - lead, silver, tin, iron and mercury - were discovered and used before 2000 B.C. In all probability, we will be dependent upon metals beyond the vision of anyone living today. In industrialized nations of the world, man's mode of living is based to a great extent on metals, and it is extremely unlikely

Jan 1, 1971