Search Documents

By Mark D. Zoback, Bezalel C. Haimson

INTRODUCTION A Workshop on Hydraulic Fracturing Stress Measurements was convened by the authors in December 1981 in Monterey, California under the auspices of the U.S. Geological Survey and the U.S. National Committee on Rock Mechanics. There are now over a dozen groups of investigators around the world who are actively using the hydraulic fracturing method for making in-situ stress measurements. Because of the extensive recent experience of these different groups, the Workshop enabled forty investigators from eight countries to comprehensively assess the status of the method. Based on the presentations and discussions at the Workshop, in this paper we briefly discuss the current status of the hydraulic fracturing stress measurement method concentrating on problem areas where further research needs to be done. A complete account of the presentations at the Workshop will be available through the Proceedings of the Workshop which will be published by the U.S. National Committee on Rock Mechanics in early 1983. The most exciting aspect of the Workshop was the discovery by the various groups of investigators that others were having very similar experiences with the method. The consensus among the different groups of investigators at the Workshop was that they were recording very similar pressure-time data in the field, they were able to interpret them in similar ways, and they were achieving results that were quite encouraging because of several factors. First, the results at various locales were found to be internally quite consistent. This was reported by investigators from Germany (Rummel, Baumgartner, and Alheid, 1982), Japan (Tsukahara, 1982), Australia (Enever, 1982), and the U.S. (see, for example, Haimson, 1978, 1982a; Zoback

Jan 1, 1982

By George W. Becker, Blair R. Benner, Ronald J. Roman

A computer model for the leaching of oxide copper heaps is developed and verified in laboratory tests. The model can be used to scale-up laboratory test data and to simulate the results of various operating philosophies on heap leaching. The model is applicable to leaching processes where the rate of leaching is controlled by a deficiency of reactant or diffusion of a reactant through the leached rock. Several examples are presented showing the sensitivity of the recovery vs. time curve to the variables in leaching.

Jan 1, 1975

By David H. Carlson, John H. Johnson

The paper presents background information, a description of mine characteristics that affect air monitoring techniques, and a review of Portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the experimental mine, the diesel dilution tunnel test cell, the mine air monitoring lab (MAML), portable instruments, and the production mines used.

Jan 1, 1982

By M. Gangal, B. Paul

It may be seen from Maurer's survey (Maurer,l 1966) that most of the common methods used in rock drilling today depend upon mechanical loading of the rock. In order to predict the behavior of rock under an imposed system of stresses, it is necessary to have a valid criterion which delineates those combinations of stress which cause macroscopic rock failure from those which do not. Admittedly, the conditions under which brittle materials fracture depend very much upon statistically variable local effects such as inclusions, grain boundaries, minute imperfections, etc. However, it is extremely desirable to be able to predict fracture under complex states of stress by means of a stress-criterion of failure, where, for a given material, the effects of the other variables mentioned are incorporated into a small number of experimentally observable parameters. One of the most successful of these "macroscopic stress criteria" has been the Coulomb-Mohr theory 2,3 (also see Jaeger 4 and Terzaghi 5), modified by the addition of tension cutoffs (Paul 6). At first thought it might seem rather odd that a macroscopic theory is capable of predicting fractures which originate at highly localized random imperfections at an atomic level (or more likely at the level of individual mineral grains in rocks). However, Griffith7 showed that fractures originating near the tips of randomly oriented elliptical cracks lead to the macroscopic stress criterion of failure indicated in Fig. 1 (a). Fig. I (a) is to be interpreted in the following way: P and Q represent the maxi mum and minimum principal stresses (compression is considered positive) in a macroscopically isotropic body; fracture will not occur for any combination of principal stresses lying within the 'fracture curve' shown, but

Jan 1, 1967

By Horace Pops, J. F. Libsch

THE discovery of SAP alloys (sintered aluminum powders) by lrmannl has stimulated investigations in other alloy systems.23 Not only do such alloys have good room-temperature properties, but they maintain high strength after prolonged service at elevated temperatures. In addition, they show high structural stability, including unusually high recrystallization temperatures. These characteristics are secured by dispersion hardening. For this investigation, Zn-ZnO alloys were selected. Practically, the fact that commercially pure zinc recrystallizes near room temperature prohibits strengthening and hardening by cold deformation and therefore limits the application of zinc where mechanical strength is important. Similarly, the poor

Jan 1, 1961

By V. Rajaram, H. W. Earnest, A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneumatic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 2700 t/h (3000 stph) to the backfill level, situated about 610 m (2000 ft) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This Paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1980

By D. M. Lewis, R. C. Emmett, B. C. Wojcik, F. A. Baczek

The ElectroSlurry™ electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon cathode, while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes. The dust is processed through several stages consisting of leaching, copper precipitation, ElectroSlurry electrowinning, and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1981

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By Y. L. Yao

A scale based on existing data for the mutual solid solubilities of metals in binary systems has been compiled. This scale is useful for estimating the relative magnitude of two solubilities, provided that these two metals do not form a continuous series of solid solutions. In his classic work on the theory of metallic solid solutions, Hume-Rothery proposed that, other things being equal, a metal of lower valency should be regarded as more likely to dissolve one of higher valency than vice versa. He called this the "relative valency effect". Later he found that the application of this general principle was limited to the three univalent metals: copper, silver, and gold. In dealing with alloys of these metals with metals of higher valency, Hume-Rothery stated, it is usually found that the solid solution of the univalent metal is of the greater extent.&apos; The question of whether there is a systematic trend in comparing the relative magnitude of mutual solubilities, if valency is not considered a criterion, naturally arises. The present paper proposes a "mutual solid solubility" scale on an empirical basis. The order of its arrangement is determined by the relative magnitude of mutual solid solubilities. Some applications of and inferences from this scale are given. ORIGIN AND SCOPE OF THE SCALE An extensive survey of over 400 binary phase diagrams shows that, with certain exceptions and within certain limitations, metals can be arranged in the following order: Na Zn Cd Ga Bi Ge Sb As Hg Sn Si Mg Li Ba In Tl Pb Al Ca Be Mn Cr Re W Mo Cu V Ta Fe Ru Cb Co Ti Hf Ni Os Zr Ir Pt Au U Rh Ce Pd Ag Th so that a metal higher on the scale tends to have a higher solubility in a metal lower on the scale than vice versa. some experimental solubility data are given in Table I. These data, unless otherwise specified, are taken from Hansen and Anderko.6 Throughout this paper, the term "solubility of A in B" is taken to mean the maximum solid solubility of A in B in atomic percent, while the maximum solid solubility of B in A in atomic percent is called "reciprocal solubility". The exceptions found in the above-mentioned survey are: Al-Ag system, 20.34 at. pct Al in Ag, 23.8 Ag in Al; Mg-Pb system, 5.9 Mg in Pb, 7.75 Pb in Mg; As-Sn system, vanishingly small amount of As in Sn, a large As primary solid solution; Cd-Hg system, Cd in Hg <Hg in Cd; Mg-T1 system, 5(?) Mg in ßT1, 15.4 T1 in Mg; W-Ti system, -21 W in ßTi, -25 Ti in W; Zr-Ag system, probably small amount of Zr in Ag, 20 Ag in ßZr.7 Considering the large number of examples, the exceptions are few. It is remarkable that metals may be so arranged without considering other factors such as size, crystal structure, electronic structure, and so forth. A limitation to the use of the scale is the fact that it cannot be tested for two metals forming a continuous series of solid solutions. It is interesting to point out that when the continuous solid solutions have a miscibility gap the critical composition is

Jan 1, 1961

By N. H. MacMillan, W. M. Mularie, R. E. Jackson, A. R. C. Westwood

The initial results of a study of the environment-sensitive microhardness and diamond rotary drilling behavior of granite and its constituent minerals quartz and feldspar (microcline)1 have established that many similarities exist between the environment-sensitive mechanical (chemomechanical) behavior of these materials and that of the simpler solids such as periclase, soda-lime glass, and alumina4 studied previously, at least as far as n-alcohol (straight-chain alcohol) environments are concerned. The results of this study (hereafter designated study I) also suggested that the rate of drilling of granite in these environments is controlled by the chemomechanical behavior of its quartz constituent, and is greatest in those environments which impart a zero l-potential to this phase, thereby maximizing its hardness. Now, cationic surface-active species strongly influence the l-potentials of silicate minerals. For this reason they are widely used in mineral separation operations. In particular, dodecyl trimethyl ammonium bromide (DTAB) was found in study I to produce f 0 for quartz at a concentration in water of 107 to 10-4 moles per 1. Accordingly, the influence of dilute aqueous solutions of this surfactant on the drilling behavior of granite also was examined in study I. This revealed that granite could be drilled three to four times faster in 10-° molar aqueous DTAB than in water, and confirmed by experiment the suggestion that granite is most effectively drilled with a diamond core bit in environments which impart a zero l-potential to quartz. According to O&apos;Connor and Buchanan&apos; however, the isoelectric point for quartz in aqueous DTAB solutions occurs at a concentration of .•.•2 x 10-° moles per 1, rather than [101 to 10-1] moles per 1. To confirm the results of study I, therefore, a more comprehensive investigation of the [ ]-potentials of quartz, microcline, and Westerly granite in aqueous DTAB environments has now been undertaken. At the same time an examination has been made of one of the basic assumptions of the current conceptual understanding of chemomechanical effects. In this view, although hardness changes occur essentially instantaneously following wetting of the solid, they are confined to a surface layer at most a few micrometers (µm) deep. Hence, to maximize the influence of chemomechanical effects on bit penetration rate only shallow cuts should be taken. Practical penetration rates are then obtained by increasing bit rotation speed. Experimental l-potentials were determined by the streaming potential technique using an automated rapid-cycling apparatus recently developed by Martin Marietta Laboratory from a design by Somasundaran and Kulkarni. The drilling studies employed 3.2-mm-OD 120-grit diamond-loaded core bits with a wall thickness of ~0.7 mm, and bit rotation speeds of 2200 and 25,000 rpm. The load applied to the bit was independent of the depth drilled in both cases. The 2200 rpm measurements employed the same drill press and puddle drilling technique as used in study I. The higher rotation speed was obtained using a water-driven dental turbine drill. In the case, the surface active fluid was pumped down the axis of the bit to ensure efficient wetting and flushing of the drilling debris from the hole. In both cases drilling rate was measured by the parameter D(200), defined as the average rate of bit penetration during the interval from 150 to 250 sec after drilling commenced.

Jan 1, 1976

By T. J. O’Neil, S. J. Kirk

In 1978, a multidisciplinary team from the University of Arizona, the Mines Project Group, conducted a study to examine reclamation alternatives for a proposed open-pit copper mine. The cost of a waste dumping plan designed by a mining consulting firm was determined as well as the cost of dumping configuration prepared by the Mines Project Group. The latter dumps were designed to be more socially acceptable and aesthetically pleasing, in addition to serving more creative end land uses than the dumps designed by the mining consultant. One dump configuration designed by the interdisciplinary team was the least expensive plan of all the alternatives considered.

Jan 1, 1984

By Clarence Fenner

THE manufacture of optical glass is a process that demands careful regulation and control at all stages in order that satisfactory results may be obtained. The product, to serve its purpose, must meet stringent requirements, which can be assured only by careful procedure in manufacture. During the greater part of the time that a pot of glass is in the furnace, temperatures should be kept within certain rather narrow limits; a departure on either side is likely to be detrimental to the glass and may result in total loss. If the temperature during melting and fining be low, the melt is likely not to fine properly and the glass will contain quantities of bubbles, or "seed," or it may become milky and unfit for use; too high a temperature, on the other hand, is severe on the pot and may cause it to leak or cast stones, or the increased solution of pot material in the melt may acid to the color of the glass and decrease its transmission. Moreover, variations in the working temperature will mean variations in the amount of selective volatilization and, consequently, variations in optical properties from pot to pot. Furthermore, in the closing stages of furnace treatment, the melt is cooled until a certain degree of stiffness is attained, when the pot is withdrawn. The quality of the glass-its freedom from striae and bubbles-will depend in large measure on whether the temperature to which cooling has been carried is suitable. For each type of glass there is a narrowly restricted range of temperature to which each pot of the given type should be cooled before withdrawal. A quick and reliable method of measuring temperatures is, therefore, of the first importance. In the optical-glass work conducted by the staff of the Geophysical Laboratory during the period of the war, much attention was given to the clatter of determining what methods would meet the requirements. This article will deal with these investigations and with the application of the results to actual practice at various plants. At the. time that the work of the Geophysical Laboratory was begun at the Bausch & Lomb plant, each melting furnace was equipped with

Jan 7, 1919

THE Institute assembled in the metallurgical lecture-room of Pardee Hall, Lafayette College, at 7 o&apos;clock P.M. on Tuesday evening, October 21st. The session was opened by the President, R. W. Raymond, with an address on Mining Industry as illustrated at the Vienna Exposition. The second session was held on Wednesday morning. The Council reported the following names for election as members and associates. They were unanimously elected. †Ayres, W. S., - Easton, Pa. *Baker, Prof. A. L., - Easton, Pa. †Browne, Thomas Nicholl, - Hamilton, Nev. *Carter, Frank, - Pottsville, Pa. *Davis, E. F. C., - Pottsville, Pa. *Fox, Prof. J. G., - Easton, Pa. *Haight, Ogden, - Etna, Pa. †Hall, Norman, - Sharon, Pa. *Knap, Joseph, - Fountain Mill, Pa. †Miller William McKeen, - Easton, Pa. †Pardee, I. P., - Easton, Pa. *Plater, John E., - Eureka, Nev. *Platt, Joseph L., Jr., - Franklin Furnace, N. J. *Plumb, W. H., - Mauch Chunk, Pa. *Reis, George L., - New Castle, Pa. *Samuel, Edward, - Philadelphia, Pa. *Smith, William Allen, - Trenton, N. J. *Smock, Prof. John C., - New Brunswick, N. J. *Weberling, Charles, - Salt Lake City, Utah. Also the following as foreign members Beaulieu, Ad. le Hardy de, - Brussels, Belgium.. Beaumont, Major Fred., - London, England. Beck, Alexander, - Mons, Belgium. Bodmer, J. J., - London, England. Brassert, Berghauptmann, Dr., - Bonn, Prussia. Brogden, James, - London, England * Members. † Associates.

Jan 1, 1874

It is desired to call the attention of young men who have had technical training and experience to the fact that their abilities can best be put at the service of the country by selecting a branch of service in which their special qualifications will be of the greatest use. The submarine force of the United States Navy requires the services, as officers on board submarines, of young men who have had technical training in mechanical and electrical engineering and who have had experience in these professions. It is intended to enroll a number of such men as provisional ensigns in the Naval Reserve Force, give then a course of instruction in deck duties at Annapolis and a course in submarine work at New London. Those who successfully pass these courses will then be sent on hoard submarines for regular duty. It is requested that any men who desire this duty and who are qualified as below outlined send their names and addresses to the Commander Submarine Force, U. S. S. Chicago, care of Postmaster, New York. Qualifications required: Desire to serve in submarines. Degree of M. E. E. E., or E. M. Two and one-half years&apos; practical experience in profession. Not over 35 years old. Physically strong and sound.

Jan 7, 1918

The Institute assembled in the metallurgical lecture-room of Pardee Hall, Lafayette College, at 7 o&apos;clock P.M. on Tuesday evening, October 21st. The session was opened by the President, R. W. Raymond, with an address on Mining Industry as illustrated at the Vienna Exposition. The second session was held on Wednesday morning. The Council reported the following names for election as members and associates. They were unanimously elected. Ayres, W. S.,.......Easton, Pa. *Baker, Prof. A. L.,.. Easton, PR. Browne, Thomas Nicholl,.... Hamilton, Nev. *Carter, Frank,......Pottsville, Pa. *Davis, E. F. C.,... Pottsville, Pa. *Fox, Prof. J. G.,...,..Easton, Pa. *Haight, Ogden,...Etna, Pa. Hall, Norman,...Sharon, Pa. *Knap, Joseph,......Fountain Mill, Pa. Miller William McKeen,.... Easton, Pa. Pardee, I. P.,....Easton, Pa. *Plater, John E.,......Eureka, Nev. *Platt, Joseph L., Jr.,.....Franklin Furnace, N. J. *Plumb, W. H.,......Mauch Chunk, Pa. *Reis, George L.,......New Castle, Pa. *Samuel, Edward,. ..Philadelphia, Pa. *Smith, William Allen,.....Trenton, N. J. *Smock, Prof. John C.,..... New Brunswick, N. J. *Weberling, Charles,.....Salt Lake City, Utah. Also the following as foreign members: Beaulieu, Ad. le Hardy de,. . Brussels, Belgium. Beaumont, Major Fred.,..London, England. Beck, Alexander,.Mons, Belgium. Bodmer, J. J.,..London, England. Brassert, Berghauptmann, Dr.,. .. Bonn, Prussia. Brogden, James,.London, England.

The following is an incomplete list of members and guests who called at Institute headquarters during the period Oct. 10, 1918 to Nov. 10, 1918. J. Carson Adkerson, Virginia. George H. Parsons, Hayden, Ariz. Andrew B. Armstrong, Connecticut. W. E. Pomeroy, New York. Courtenay DeKalb, San Francisco. Ezra C. Rider, Bisbee, Ariz. Clifford G. Dennis, San Francisco. H. W. Seaman, Chicago, Ill. Rudolph Emmel, Boston, Mass. William Allen Smith, Northampton. Emil Gathmann, Baltimore Md. R. K. Stockwell, Salt Lake City, Utah. Ernest S. Geary, Denver, Colo. W. G. Swart, Duluth, Minn. W. E. Hopper, Washington, D. C. Kirby Thomas, New York. W. Spencer Hutchinson, Boston, Mass. - Warren D. Thompson, Harvard Club. E. W. Kohl, Jr., Philadelphia, Pa. H. Vincent Wallace, Los Angeles, Cal. E. C. Nighman, Butte, Mont. Paul T. Benson, formerly with the Tacoma smelter, has resigned his position there to accept one with the Great Metals Mining and Milling Co. at Nespelem, Wash. Prof. Edward E. Bugbee, of the Mining Department of the Massachusetts Institute of Technology, has been granted a leave of absence to accept the position of Assistant Director of Education for the S.A.T.C. of five southern states with headquarters at Raleigh, N. C.

Jan 12, 1918

By Alvin Kaufman

At the turn of the century the U.S. had a gross ALVIN KAUFMAN Mineral Economist U.S. Bureau of Mines area slightly in excess of three million square miles, a population of 76 million, a gross national product of $37 billion (constant 1929 dollars) and a mineral production valued at $2 billion (1929 dollars). Some 60 years later its area had increased by 600 thousand square miles, population had risen 140%, gross national product was seven times greater and mineral production had grown to a value five times that of 1900. Of perhaps greater significance, however, were the changes wrought by technology. It was during this period that the "American Way of Life" was revolutionized by the introduction of the airplane and the automobile; man also took his first probing steps in the utilization of nuclear energy and pre- pared to unlock the secrets of space. It was during these six decades, also, that he learned to create additional new materials, some of which were from old sources such as plastics from petroleum and coal. These new materials have created competition and attendant problems for the traditional materials such as iron, copper, lead and zinc. Additional problems undoubtedly will be created by technologic advances in the future.

Jan 2, 1963

Discussion of the paper of WALTER 0. SNELLING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. F. LUCAS, Washington, D. C.-Are the results of the experiments in practical operation? WALTER 0. SNELLING.-There have been no large-scale operations up to the present. The necessary conditions of temperature are easily arranged for, but the required condition of pressure, 800 lb., is not so simple a matter. The company has been working on this problem, and at the refinery in Oklahoma work of this kind is now being carried on. The way in which an ordinary still will leak at 50 lb., and more at 100 lb., leaves some doubt in the mind of many as to what can be clone at a continuous working pressure of 800 lb. On the other hand, the fact that they are making ammonia abroad by a method which employs higher pressures and temperatures than anything involved in this method, leads me to believe that the difficulties, which will undoubtedly arise when this is attempted on a commercial scale, can be overcome. WILLIAM N. BEST, New York, N. Y.-Is there any change in the calorific value of these oils?

Jan 5, 1915

C. R. CORNING, Chairman. ADOLPHE E. BORIE, First Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. Vie-Chairmen. JOHN H. ALLEN, GEORGE M. COLVOCORESSES, RICHARD M. ATWATER, JR., ROBERT PEELE, GEORGE D. BARRON, CHARLES P. PERIN, A. CHESTER BEATTY, JOSEPH A. VAN MATER, J. PARKE CHANNING, ARTHUR L. WALKER. D. C. Bard, Howard Eckfeldt. Philip N. Moore, W. de L. Benedict, R. C. Gemmell, T. H. O&apos;Brien, John C. Branner, F. Louis Grammer, James J. Ormsbee. Palmer Carter, Ernest A. Hersam, Edward W. Parker, Allen J. Clark, Edwin C. Holden, John B. Porter, F. Crabtree, William L. Honnold, R. DI. Raymond, George G. Crawford, Reginald E. Hore, Robert H. Richards, O. C. Davidson, C. Colcock Jones, LeRoy Slash, E. V. D&apos;Invilliers, Eugene P. Kennedy, Frederick H. Sexton, James S. Douglas, Chester F. Lee, Henry L. Smyth, Walter Douglas, Richard S. McCaffery, F. W. Traphagen, Howard N. Eavenson, James F. McClelland, Elton W. Walker. Milton H. McLean, The Chairman of the Committee on the eve of his departure frog -,he country for an extended stay, addressed the following letter t ,he President of the Institute NEW YORK, N. Y., APRIL 19, 1913.

Jan 5, 1913

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation&apos;s Utah Copper Division. This operation is the world&apos;s largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979