Search Documents

By LeRoy Scharon, P. Uhley

TEST gravity surveys were made in the Washington County barite district of Missouri on properly owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maximum difference in elevation being 400 ft in a distance of 3½ miles. The purpose of the test gravity survey was to determine whether the gravity method of geophysical prospecting might be applied in the exploration for barite deposits in the Washington County barite district, since a satisfactory systematic procedure had not been devised to explore and ultimately determine barite ore reserves with desired accuracy. No previous geophysical work with respect to barite is known to have been done in this area. Stratigraphy: The formations over which the barite deposits occur' are Paleozoic in age, representing rocks involving sandstones and dolomites unconformably underlain by pre-Cambrain granites and rhyolite porphyries. The areas covered by the granite survey were directly underlain by almost

Jan 1, 1955

By H. W. McCue

In 1945 the number of oil wells drilled was less than in 1944 but the number of gas wells was greater. The oil wells numbered 176, completed for an initial production of 25,214 bbl., an average of 143 bbl. per well as against a total in 1944 of 245 drilled for 32,886 bbl., or 134 bbl. per well. All of these wells were in proven areas and no new discoveries

Jan 1, 1946

By F. J. Haller

The need for permanent, fireproof support indicated structural steel sets. Experience over the past six years, involving more than five miles of permanent underground openings, has proved that steel is permanent, safer and, in the long run, cheaper than either treated or untreated wood supports. Excavation is reduced, as are installation, transportation, and handling costs. A number of hazards are reduced or eliminated by the use of steel.

Jan 4, 1950

By S. Jess Larsen

Modern technology has provided the world with many innovations to improve living standards, ease of job performance, efficiency, and managerial control. While not expected to compete with the computer revolution, Kerr-McGee Coal Corporation has found a way using laser technology to solve one of their haulage problems. Operating successful and profitable surface coal mine facilities in Wyoming's Powder River Basin require economies of scale, flexibility of operation, conscientious cost control, and ever-present innovative effort. Because haulage costs are the major source of expenditure in surface mining, Kerr-McGee recognized early the need for maximum haulage productivity and the economies of scale provided by large haulage trucks. Special conditions that exist in the Powder River Basin coal fields require consideration. The coal thickness (up to 100 feet and more) and varying depths of overburden dictate that a haulage unit with good gradability characteristics be used to avoid undesirable long ramps. Two and often three coal seams are encountered by most mines, which necessitates operating from several coal and parting faces simultaneously. This situation consumes much space, and to minimize the scope of problems, a coal haulage unit with good maneuverability and stability is needed. Finally, the low density of coal (±1500 pounds/loose cubic yard) demands a large volume capacity to utilize truck load carrying capability effectively. These conditions prompted Kerr-McGee to select unitized two-axle bottom dump trucks of the 160-170 ton size for primary coal haulage at its two Gillette-area mines. Use of 170-ton bottom dump trucks at the Clovis Point Mine handles most of the coal haulage, but the truck

Jan 1, 1983

By Archer E. Wheeler, Milo W. Krejci

There are two general methods in use for the production of metallic copper from matte which are worthy of consideration : (1) the Welsh blister process, and (2) the converter process.' As practically all of the copper produced to-day is made in converters, we will give a brief outline of that process before proceeding with the special subject of this paper. Matte may be roughly defined as a mixture of the sulphides of copper, iron, nickel, silver, etc. In the converter process this is blown up to metallic copper in a modified type of Bessemer converter. The conversion of matte consists mainly in, (1) the removal of sulphur in the form of SO2, and (2) the slagging of the iron. With this brief statement we come to the two subdivisions of the process of converting mattes: Converting with acid linings. Converting with basic linings. Converting with Acid Lininys, This is carried out by lining the converter with siliceous rock or ore, which performs two functions: It protects the iron shell of the converter from the molten charge, and it furnishes the silica for combining with the iron as it is oxidized from the matte, to form a ferrous silicate. It follows from the second of these functions that this siliceous lining must be replaced from time to time, and in practice it has been necessary to reline converters every 8 to 40 hr., this time varying in different plants and even with different linings in the same plant, the life of a lining depending upon the grade of the matte treated, and upon the composition, the thickness, the tamping, and the drying of the lining.

Jan 1, 1914

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By Terry G. Richard, Vernal H. Kenner, Sunder H. Advani

This paper presents and discusses the results of thirty-one fracture toughness tests on Pennsylvanian Age Clay Shale. Two different orientations for this anisotropic material were studied and two series of tests were conducted, namely, 1. a test series to determine the effect of moisture content on fracture toughness, and 2. a test series to study mixed mode fracture. Increased absorbed moisture is found to reduce fracture toughness. Several analyses of mixed mode failure are found to give varying non-conservative predictions of failure stress intensity level.

Jan 1, 1982

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

By F. G. Miller, J. M. Podgursky

Laboratory and pilot plant work on tabling of 14-mesh X 0 hydrocyclone under flow are summarized. Included are: operating principles of hydrocyclones and tables; performance of these two devices, separately as well as in combination; comparison of the combination hydrocyclone-table system with other fine-coal processing systems; and application of the hydrocyclone-table system in fine-coal circuits. The data show that the table actually compensates for the shortcomings of hydrocyclone and makes a combination table-hydrocyclone system attractive, particularly in those cases where fine pyrite is one of the major contaminants.

Jan 1, 1973

By Philip B. Bucky

THE Mining Methods sessions, one of which was run jointly with the Industrial Minerals Division, were fortunate in having a number of exceptionally fine papers. At the Tuesday session R. P. Smith presented the results of six years' experience with prepaid medical care for the employees of the Hollinger mine. It was felt that this paper was a real contribution to the cross field of mining-medicine, and the presentation was exceptionally well done. Olof V. Lindqvist acquainted us with the consider- able progress made in blast-hole diamond drilling in recent times, especially in Canada. The opening of a mine is always a matter of considerable interest and the description of the procedure and problems encountered in opening the Mather mine of Cleveland Cliffs Iron was presented by L. C. Moore.

Jan 1, 1944

By Dan Chun

Abstract-To facilitate the efficient handling of large volumes of information generated by logging exploration drill cores, a computer data bank system (GEOBANK) has been developed to store and retrieve the normally difficult to handle geologic information as well as the physical testing data. The data bank systematized the logging of drill core by first developing a standard list of adjectives or descriptors (with the corresponding assigned numerical codes) for the various stratigraphic categories that are also assigned numerical codes. The system uses the "floating-slot" concept and handles the data bank with one single input form.

Jan 9, 1978

By Robert H. Richards

DuRing the winter of 1868-9,I was called upon by Professor F. H. Storer, to put up the Bunsen filter pump in the chemical laboratory of the Masschusetts Institute of Technology. As the laboratory is on the lower floor, it was found necessary to use a great deal of cumbrous pipe and apparatus to get the necessary column. It was then suggested that if an instrun~ent could be devised which would make use of the hydrant pressure in the service-pipe, it would do away with the objectionable features of the Bunsen pump. After using the Bunsen pump for some years, the jet pump to be described in this paper was devised, and it has since been adopted by Prof, Wing in the quantitative laboratory of the school. I am much indebted to Prof. Wing for his aid in starting the manufacture in brass of these jet pumps, whieh are now to be had in Boston. The jet pump much resembles the Giffard injector in form. It, differs from it in the fact that water is the impelling fluid, and air the impelled, while with the injector steam is used to impel water. The principle of condensation of steam, which is availed of in the injector, is entirely wanting in the jet pomp. The jet pump consists in a water jet, w, (see figure), a constriction or waist, a, and a waste tube, o. The success of the jet pump depends on the follow ing conditions: 1. The relation between the sizes of sectional area of a and w. ' 2. The proximity of n and w. 3. The form and angle of the two hollow cones whose vertices make the constriction a. 4. The relative size of sectional area of w and o. 5. The zigzags, or an equivalent means of making foam. In the following discussion, let a, w, and o repre sent the diameters of these parts of the jet pump. A number of experiments were' .tried to ascertain

Jan 1, 1879

By D. E. Munson, H. J. Sutherland

Surface subsidence caused by underground mining is described through complementary influence functions. The complementary functions developed here differ from the simple functions previously used in that the surface displacement is the result of the combined contributions of the mined and unmined zones. This eliminates computational difficulties experienced with the simple functions in determining the deflections above the rib side and in the eventual application of influence functions to complex room-and-pillar configurations. Although the analysis framework presented is intended for predicting subsidence over complex mine configurations, use of the complementary functions is illustrated adequately by application to a longwall panel of the Old Ben No. 24 coal mine.

Jan 1, 1982

By M. G. Schuerger, D. W. Park

An improved gage for monitoring fractures in underground openings was successfully developed using the reflection photoelastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so reme¬dial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by using rubber backing. Crack growth as little as 76µm (0.003 in.) up to as much as a 2.54-mm (0.1-in.) width were detect¬ed in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in a laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1984

By Alex G. Sciulli

This paper discusses the primary computer programs used by the Mine Safety and Health Administration's Bruceton Safety Technology Center to evaluate coal refuse disposal plans. These programs are currently being used by private consultants, government, and the coal industry for today's coal refuse disposal problems. This paper outlines five programs, their special features, and their importance in the design and construction of coal refuse disposal facilities. The purpose of the paper is to present the general steps necessary in the computer-modeling of each program. The programs that are discussed include BISHOP, STABL, RWE, DAMS2, and HEC-2, which cover the subject areas of slope stability, hydrographs, flood routing, and water surface profiles.

Jan 1, 1983

By A. L. Field

This general subject has been so thoroughly discussed by Dr. Herty and his associates, especially with regard to the degree of oxidation of the metal at the time that the silicon pig or spiegel is added, that I am not going to spend much time on that today. I should like to propound a question, which is based on my own observations made some years ago while with a large alloy-steel company which had two open-hearth furnace plants. It is true that one of these plants was not engaged particularly in making alloy steels, but there were certain relations between slag and metal composition which appeared to me to be entirely different in the two plants. I have an explanation for it that is more or less incomplete, but possibly Dr. Herty or Mr. Reinartz or some of the others may be able to complete it. Suppose we take our three layers; the metal on the bottom, on top of that the slag, and on top of the slag, the gas. We cannot overlook the gaseous phase. Regardless of the effect of the iron oxide in the slag on the rate of carbon elimination—and that, of course, is rather important in alloy practice since it is not desirable to have the carbon dropping too rapidly at the time the deoxidizing is had in the furnace—it will probably be admitted that it depends on the iron oxide in the metal for a given carbon oxide. I have seen cases where with approximately identical metal and slag compositions one furnace would work twice as rapidly as another in removing carbon. Of course, there is some explanation of this in what others have already said, that the question of the exact lime and silica content of the slag determines the activity and viscosity of the slag; but I am convinced, without having reviewed the actual records since I was asked to make this talk, because they were not available at the time, that the slags in these two furnaces were not materially different. Putting it another way, one furnace would have

Jan 1, 1935

By A. L. Field

This general subject has been so thoroughly discussed by Dr. Herty and his associates, especially with regard to the degree of oxidation of the metal at the time that the silicon pig or spiegel is added, that I am not going to spend much time on that today. I should like to propound a question, which is based on my own observations made some years ago while with a large alloy-steel company which had two open-hearth furnace plants. It is true that one of these plants was not engaged particularly in making alloy steels, but there were certain relations between slag and metal composition which appeared to me to be entirely different in the two plants. I have an explanation for it that is more or less incomplete, but possibly Dr. Herty or Mr. Reinartz or some of the others may be able to complete it. Suppose we take our three layers; the metal on the bottom, on top of that the slag, and on top of the slag, the gas. We cannot overlook the gaseous phase. Regardless of the effect of the iron oxide in the slag on the rate of carbon elimination—and that, of course, is rather important in alloy practice since it is not desirable to have the carbon dropping too rapidly at the time the deoxidizing is had in the furnace—it will probably be admitted that it depends on the iron oxide in the metal for a given carbon oxide. I have seen cases where with approximately identical metal and slag compositions one furnace would work twice as rapidly as another in removing carbon. Of course, there is some explanation of this in what others have already said, that the question of the exact lime and silica content of the slag determines the activity and viscosity of the slag; but I am convinced, without having reviewed the actual records since I was asked to make this talk, because they were not available at the time, that the slags in these two furnaces were not materially different. Putting it another way, one furnace would have

Jan 1, 1935

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By John H. Smith

Because of increased pressure from federal and state regulatory agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Development of a waste treatment process minimizing equipment cost and utilizing land efficiently is mandatory. Methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, such as iron, needing aeration, add to the problem of concentrating neutralized solids.

Jan 12, 1972