Search Documents

By W. Fletcher, R. C. Schenk

This paper outlines a well proven and highly successful approach for eliminating many of the problem and frustrations often experienced in plant startup. The approach was developed over a period of 25 years during which some 90 plants were commissioned. This paper discusses startup from the contractor’s perspective and highlights the requirement for detailed startup planning, careful coordination during the project final construction phase, and thorough checkout of equipment prior to introduction of feed. Performance of these services has demonstrated a valuable opportunity exists for the contractor to assist in the training of the plant operating personnel.

Jan 1, 1983

By J. M. Lohr

THE characteristics and uses of thermocouples of platinum and the platinum alloys being so well known, this paper will be confined to base-metal couples. During the past decade, there has developed a strong demand for thermocouples made of metals cheaper than the platinum alloys, and suitable for industrial heat measurements. Much research has been clone but only a very limited number of alloys have been found to possess the necessary characteristics for general technical use. In the development of thermocouple alloys it is necessary to consider the following points: The electromotive force and temperature relations; permanency or constancy; reproducibility; manufacturing difficulties; durability; and accuracy in use. The electromotive force developed by the thermocouple should increase with the rise of temperature according to some definite law. It is desirable that the electromotive force should vary directly with the temperature difference of its junctions, in other words, giving a curve linear or nearly so. It is also desirable that the resulting electromotive force be as large as possible for any given range of temperature, thereby insuring greater accuracy of readings.

Jan 9, 1919

By Thomas W. Yardley

In many years' experience as a maker and purchaser of cast-iron coated pipe, I have never met with any standard form of specifications for such. Each water-works company, employing a hydraulic engineer, has, under his direction, prepared complete specifications for the particular conditions required; but I cannot find that any two are alike; and each foundry, in bidding for the supply of such pipe, makes the price to cover the conditions' required. I, therefore, have the honor of offering to the Institute a form of specifications for cast-iron coated water-pipe, that may be found useful to water-works companies and others requiring pipe of this kind. The conditions are all reasonable, and can be carried out by makers without additional cost, and with advantage to the purchaser. Section 1 gives the kind of pipe, with its general characteristics. Section 2 specifies that neutral pig-iron shall be used, since such iron possesses the strength required, and is uniform in its shrinkage. Section 5, requiring makers to give the brands of pig-iron used

Jan 1, 1890

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cureall" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made.

Jan 1, 1950

By Robert J. Brison

On the basis of experience accumulated during the completion of some 150 gold/silver process development projects, general guidelines are presented for developing the most cost effective process for a specific project. Steps involved in process development for lode ore deposits generally include a review of pertinent background information on the ore deposit, sample procurement and preparation, sample characterization, study of concentration possibilities, investigation of leaching and metal recovery methods, economic evaluation of alternative processes, optimization of the selected process, a pilot plant program if warranted, and finally, process design and feasibility studies. Each of these steps is discussed, with emphasis on the relation between technology and economics.

Jan 1, 1984

By E. P. Mathewson

(Butte Meeting, August, 1913.) IN a discussion -of a paper on " The Basic Process as Applied to Copper Smelting," by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1S91,1 Prof. W. C. Roberts Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Marshes process would afford anything like the service which it had been shown to render in the metallurgy, of iron. Claude Vautin stated that he had experimented for over two years with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned, Herman Keller, Superintendent of the Parrott smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were -too small. A short time; afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., said at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines.

Jan 6, 1913

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By O. Jay Myers

THE war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for cores and mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from 0.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content varies between 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. PROTECTIVE AGENTS In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H20 -+ H21 + MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed `burns'). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the castings unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beck. A possible explanation may lie in the following equation: 2Mg + 02 -s 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945

By A. L. Bailey, B. A. Landry

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally. Of course, the matter is rendered complex by the circumstance that the float-and-sink test, not a simple analytical measurement but a process test, comprehends a number of more-or-less independent items of fundamental data; and as shown in the report, the' variability of the samples differs with respect to these different items. This condition and the wide variety of situations in which float-and-sink test data are used, in combination with other factors, to study complex process operations, indicate the difficulty of setting up fixed standards for float-and-sink sampling and testing. At this stage at least, it is the intent rather to obtain experimental data on the principal Factors involved so that the reader may arrive more intelligently at a procedure adapted to his problem. The authors of this paper have presented experimental data showing the relationship between size of sample and particle size for different variability tolerances with respect to percentage of sink. In further studies, data are being collected to appraise also the variability of the samples with respect to float-ash content and size consist. The scope of this work will be broadened to cover particle sizes up to 4 in., and a third series of tests has yielded similar data for a much cleaner type of raw coal. Thus, the further studies will make available a fairly comprehensive meas- ure of variability with respect to size consist, percentage of sink, percentage of middlings, and percentage of ash in the float, for three coals ranging from 3.87 to 17.68 pct in refuse content (heavy sink material) and from 4.18 to 17.52 pct in middlings. Introduction At present there are no published standards for float-and-sink test sampling. During the rapid expansion of float-and-sink test work, varying procedures have been based on adaptations of the ASTM standards for sampling coal for analyses. For this reason, a special study of gross sample reduction has been undertaken to determine the limits for this step in the operation where no reduction in particle size is to be made before testing. Float-and-sink tests are made whenever a thorough study of coal characteristics is desired. The tests may be made on samples from coal-cleaning units such as jigs or tables, or coal samples may be tested which are taken from a loading boom, railroad car, or the coal seam itself. The resultant gross sample may be large and pose a problem of sample reduction. The question is, then, how much can the sample be reduced and still fall within preassigned limits of accuracy of the original gross sample of coal? Coal from channel samples may be crushed to liberate impurities and then separated into various gravity fractions from which washability curves are drawn; from these curves, it is possible to determine the cleaning characteristics of the coal. However, coal samples from coal-cleaning units cannot be

Jan 1, 1950

By C. P. Miller

In order to determine the usefulness of geochemical and biogeochemical prospecting for nickel, ten localities representing several types of nickel occurrences were selected as sites from which to collect plant and soil samples. This report covers the investigations in two of the areas. After a brief geologic description of the areas, the author presents details of the experimental tests and resulting data. Conclusions drawn from the studies led to several general guides for further prospecting. In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about three years ago, approximately ten localities, representing several different types of nickel occurrences, were sampled and about 1500 samples of plant and soil were collected. This report will cover briefly the data and results for two areas, and a summary of guides for prospecting. DESCRIPTION OF AREAS SAMPLED One locality is the Red Flats nickel prospect in Curry County, Ore., about six miles southeast of Goldbeach, and the other is the Little Rocky Creek prospect in Stillwater County, southcentral Montana, just southeast of the Benbow chromite mine. The Oregon area is a lateritic-type nickel deposit formed on a nickel-rich serpentinite peridotite complex, similar to the Josephine intrusion in southwestern Oregon. The Montana area is a nickel prospect in norite, peridotite, and related rocks of the Stillwater igneous complex. The Stillwater complex is a series of layered basic and ultrabasic rocks, with a layer of norite-gabbro at the base and a series of peridotites and gabbros above. The nickel in the Oregon deposit occurs in both the peridotite and the overlying soil. A deep lateritic soil is developed locally on the peridotite and serpentinite and constitutes the ore. The average nickel content of the lateritic soil is less than 1 pct, whereas the nickel content of the weathered peridotite is about 1 to 1.5 pct. The nickel occurs as garnierite (Mg, Fe, Ni, Mn)3 (OH)4 (SiA1)2O5 in the soil and in the olivine and pyroxene in the peridotite where it probably substitutes for Fe2+ or Mg2+ in the silicate lattices. Nickel is found in three distinct ways in the Still-water rocks: 1) it is in the olivine and pyroxene minerals in norite, harzburgite, etc.; 2) it occurs as widely disseminated grains of pentlandite-pyr-rhotite, which tend to be concentrated in the lower norite band; and 3) it occurs as discrete bodies of pentlandite-pyrrhotite and chalcopyrite which are localized in the norite zone, close to the contact with the underlying rocks. The nickel content of the norite is probably less than 1 pct, and the nickel content of the pods and lenses within the norite is about 1 pct. PROSPECTING APPROACH Although the areas are different geologically, the approach in prospecting them is fundamentally the same. The procedure is twofold: 1) a rapid reconnaissance survey to outline an area of high nickel content, and 2) a more detailed survey to outline zones of possible ore grade within the area of high nickel. The possible ore at Red Flats is concentrated in the lateritic soil, whereas at Little Rocky Creek it is in the sulfide pods. Both types are surrounded by an area of relatively high nickel content. CHEMICAL ANALYSIS Chemical analyses of nickel were made by a di-methylglyoxime colorimetric test, similar to the standard test for nickel, utilizing concentrated sul-furic acid for extraction. The lower limit of detection for nickel in soil by the method used was about 10 ppm and for nickel in plants about 5 ppm. The relative deviation was about 25 pct. SOIL PROSPECTING General Statements: A summary of the approximate average parts per million of nickel in soil, as compiled from the literature and from my study, is given in Table I. Selected references are given at the end of the paper. Few of the investigators reported the type of extraction or analysis, so the data given may not be strictly comparable to mine, which were made with a sulfuric acid extraction. Any nickel concentration greater than these average values might be considered anomalous, although each area must be studied in relation to the surrounding rocks. Method of Soil Sampling: The soil samples were taken in a zone from 1 in. to 1 ft below the humus layer, and within a 15-ft radius around a station.

Jan 1, 1961

By William B. Plank

PRESENT enrollment of 182,361 students in the engineering schools of the United States and Canada represents an increase of 6.6 pct over the enrollment in these schools in 1951-52. Thus is brought to a halt the steady decrease in engineering enrollment that began with the close of the 1947-48 academic year, five years ago. The mineral engineering student picture is similarly encouraging. In the United States schools, 9453 students are preparing themselves for positions in the Mineral Industry. This is an increase of 8.3 pct over last year as compared with an increase of 6.6 pct in the total United States engineering enrollment. The rate of recovery for the mineral engineering group is thus more rapid than for the engineers as a whole.

Jan 4, 1953

By Robert L. Grayson, Y. J. Wang, R. Mike Mishra

Prediction of ventilation needs in long range mining projections requires serious consideration when formulating those projections. Predicting the behavior of the ventilation system of an old, complex mine poses an especially provocative problem. Air-flow around and through mined-out areas via bleeder systems, leakage flows through stoppings or other air control devices, and the use of multiple fans all add to the basic complexity of a ventilation system and make predictions of ventilation changes very difficult. Fortunately, the task of making ventilation decisions can be greatly assisted by ventilation surveying and computer simulation. The Nemacolin Mine of Jones and Laughlin Steel Corporation, located in Southwestern Pennsylvania, is one such old mine which used the computerized approach successfully. A mine-wide pressure-quantity survey was used to obtain realistic values for airway resistance factors. These values, together with network topology, formed the basic input for computer simulation. Results from this simulation indicated that air quantities generated at critical airways by the model were generally within a couple of percent of those measured in the actual survey. It was then concluded that the model was acceptable for practical application, and it was used immediately for studying the effects on the ventilation system of changing the blade settings of fans. Additionally, the model was modified to incorporate projected mine development and used to predict future ventilation.

Jan 1, 1982

By Wilbur Stout

IN Ohio, the annual output of coke made from native coals has averaged not more than 70,000 tons, or about enough to run a 200-ton blast furnace. Raw coal locally mined from the Sharon, or No. 1, bed was used for iron smelting in Mahoning furnace at Lowellville, Mahoning Co., as early as 1846. This practice was continued in the Youngstown district until the coal became scarce and the Connellsville coke more popular. At present, the Sharon bed contributes a part of the fuel for the production of ferrosilicon iron at Jackson, Jackson Co. About one-third native coal and two-thirds soft coal are used. In this state, coke, on a commercial basis, was first made in Jefferson County probably about 1861 or 1862. The coals used were the Steubenville Shaft, or Lower Freeport, and the Strip Vein or Middle Kittanning. The practice, however, was discontinued before 1880 because of the competition of superior foreign cokes. Beehive ovens, later built at Leetonia, Columbiana Co., were operated for only a few years; the coal used at this place is the Lower Kittanning or No. 5. In a desultory way, slack from the Pittsburgh coal has been coked at a few places in eastern Ohio, and attempts, either for experimental or for commercial purposes, have been made in other parts of the State. Small quantities of coke were made from the Upper. Freeport coal at Salineville, Columbiana Co., and near Nelsonville, Hocking Co.; the results were poor. Tests were made of the Middle Kittanning coal near Zanesville, Muskingum Co., at Moxahala Furnace, Perry Co., and at Washington Furnace, Lawrence Co.; the cokes were all high in sulfur and ash. Attempts were made to coke the Clarion coal at Vinton Furnace, Vinton Co.; a small battery of molding ovens and a pile of high-sulfur coke yet remain to tell the story. The Pittsburgh coal was coked on a commercial scale at Utley and at Lathrop, Athens Co.; but the operations were not successful and were soon abandoned.

Jan 9, 1919

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By Jan M. Mutmansky

Main purpose of the research described is to apply the method of computer simulation to the process of tunneling by rapid excavation methods. Primary attention was focused on the materials handling subsystem because of its potential for improvement from a systems standpoint. A description is given of the computer model and a summary of some applications of the model for improving the rapid excavation process is included.

Jan 1, 1975

By Sinha D. K.

As the main source of indigineous energy, coal has a big role to play in the development of national economy of India. Nationalization of the coal mining has brought the entire industry under the unit control of the Central Government following which an ambitious plan for increasing the coal production in the next few five year plans has been undertaken. In order to achieve best all round results, economy-mathematical models of Planning the total system, right from the highest to lowest hierarchial levels of decision making, have been proposed through a Global Model which is detailed in Local Models in stages right up to a mine. Optimum obtained by computer solution of the models would provide basis for objective decision making in the fields of selection of optimum plan for developing the industry, the coal fields and the mines with construction and/or reconstruction of mines, capacity optimization of enterprises and mines therein. Different types of Models and the optimization processes are presented.

Jan 1, 1977

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,' Si." —large a solubility: Al.9

Jan 1, 1954

By Alfred H. Brooks

Less than a decade ago the consumption of coal in Alaska was practically limited to the salmon canneries and the few ode-mines and settlements along the Pacific coast of the The-itory. The sparse population of the interior depended on the forests, that of the shores of Bering sea and the Arctic ocean on driftwood for fuel. All this has changed. The thousands, who have sought and mined gold on the Seward peninsula since 1898, have much impoverished the long-accumulated supply of driftwood, and at the same time the constantly increas-ng demand for fuel, on the part of the placer-camps and steamers, has resulted in heavy inroads being made on the accessible timber of the Yukon and its tributaries. While, on the one hand, the immediately available store of wood has decreased, on the other, the consumption of fuel because of the rapid expansion of the mining and fishery industries, and the attendant growth of population has much in-creased. Alaska, therefore, offers a constantly growing market or coal and other fuels. As the local coal-production has been nsignificant, the demand has been met by importations from Washington, British Columbia, and even from Pennsylvania and Australia. Fuel- Consumption. Mr. D. H. Jarvis, Collector for Alaska, has kept systematic records of the trade of the Territory since 1903. The statis-ics of the coal-importations of the past two years are shown n Table I. If data were available for a longer period of years, he increase of coal-importations would be much more striking.

Jan 1, 1906

By Ralph Wilcox

THE diamond drilling of certain characters of unstable rock forma-tion, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as " caving" of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving-with resultant difficulties, such as decreased speed of sinking and increased consumption. of diamonds-would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the outside of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the .drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole.

Jan 10, 1913

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field. which furnishes us

Jan 1, 1927