Search Documents

By J. B. Scott, J. S. Nelson, G. H. Kruse, W. S. Johnson, K. L. Zerneke

The economics of pressure tunnel design emphasize the utmost utilization of the least expensive pressure-resisting material available, namely, the rock surrounding the tunnel. A major difficulty in the design is the problem of transferring internal hydraulic pressure to the rock through a tunnel lining or membrane provided to maintain watertight conditions. The lining is necessary not only to prevent water loss, but to prevent the diffusion of water at high pressure through joints and fractures beyond the confines of the tunnel, an occurrence which could ultimately affect the stability of the rock mass through which the tunnel passes. Because of its toughness and ability to bridge localized areas of weakness, steel is used for a lining material whenever high internal pressures are involved. The steel lining is coupled to the surrounding rock mass through an annular ring of concrete backfill. It is paradoxical that the steel lining, needed primarily to assure water tightness, must of necessity be incorporated into the structure as a major pressure-resisting component, not to augment the bearing capacity of the concrete and rock, but to limit the strain for the safety and preservation of the steel lining itself. With the deformation modulus of the steel so much greater than that of the rock, the liner approaches its yield strength before the load capacity of the rock can be fully mobilized. An economical determination of plate thickness for steel liners is therefore dependent upon measurement of the properties of the surround-

Jan 1, 1970

By Walter Wood

The specifications for locomotive-cylinders, which are given in a separate paper at this meeting, have been prepared so that castings (upon the successful use of which so much depends) shall be made to conform to standards that will yield good results. After the essentials, which go with a sound and perfect cauting, the requirements to be borne in mind are those concerning the quality of the material. These have been determined from the actual practice of the largest users,—representatives of the American Locomotive Company, the Baldwin shops, and the Pennsylvania Railroad being upon the Committee. The results called for by the test-bar have been carefully checked by actual experiment upon metal that has given satisfactory service in cylinders.

Jan 1, 1905

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.1 Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques.

Jan 12, 1957

By Donald Cummings

MEASURES appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-19 has accumu-lated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors-the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Con-trol of the danger arising out of prolonged contact with pernicious air-borne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects-one, medical; the other within the province of the engineer.

Jan 1, 1938

By Thomas M. Plouf

Getting optimal performance from flotation cells can, in many cases, be critical to a project's economic viability. Simple testing procedures can sound early warning signals as well as maintain optimum recoveries from the flotation cycle. The materials required for a simple testing laboratory include: (1) pH meter or pH paper, (2) bottles of reagents used in plant flotation, (3) stop watch, (4) calibrated eye droppers. (5) laboratory flotation machine (1000-g tank, open impeller), (6) froth collection pans, (7) magnifying glass, (8) sizing screen sufficient to retain 10% of the flotation feed coarse fraction, (9) sizing screen for the size particles at which desliming of the plant flotation feed is to take place, and (10) a set of screens covering the complete range of feed particle size.

Jan 4, 1978

By Derek C. Shelton

This chapter covers the preparation of specifications for a dry crushing and wet grinding comminution circuit.

Jan 1, 1982

As we understand the functions of the A. I. M. E. Petroleum Division, they are to discover and promote knowledge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends upon the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas. To some extent, A. I. M. E. activities must be determined by the changing current needs of society. The great problem ahead of the world for some time is to evolve equitable types of production control in many industries, and especially is that true of the oil industry. Production control in this industry is as much an engineering function as is production development, notwithstanding it also involves the lawyer, the economist and the politician. It must be built on and around suitable engineering planning enforced by public opinion and legislation. We believe the prerequisite to any satisfactory solution of the oil industry's ills is an educational campaign establishing a better public understanding of the needs and merits of production control, by which we mean the maximum yield at the minimum cost coordinated to society's current needs. The underlying causes of the oil industry's ills are well known and generally agreed upon. In like manner there is general agreement among students of the industry that the first step toward their correction would be general adoption of oil-field developing and operating methods that would permit most efficient use of reservoir energy; that would provide for equitable distribution of oil and gas among the several owners in the pool; and also for the extraction of these products in response to market demand. It is now found, however, that general adoption of such developing and operating methods unfortunately cannot be brought about without changes being secured in certain basic laws of oil and gas, and perhaps also in the anti-trust laws. These legal changes are difficult to secure because of the widespread fear that they would tend to place the oil industry more exclusively in the hands of the major companies, and that

Jan 1, 1932

By R. L. Manegold

IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source -possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10. in. cannot be considered for large installations, even though they are desirable because of the continuous and, automatic tramp, iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the, presence of iron, and the conveyor belt must be stopped for its manual removal. The, stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic, head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1952

By H. W. Smith, A. K. Bjerring

A nonlinear dynamic model for a flotation cell is developed, using a number of simplifying assumptions, the most important of which is that of essentially complete liberation in the feed material. Using this model, a complete dynamic model for a flotation circuit is developed and calibrated against steady- state process data. The dynamic response of the circuit to disturbances in input feed rate and composition is simulated, as is the response of a linearized and simplified model on which control design might be more easily based. Preliminary results indicate the practicability of the modeling technique. However, difficulties in matching steady-state operating conditions in one process stream, and the apparent importance of recycle streams as indicators of process operation, indicate that inclusion of at least one species of middling particle in the model should be considered.

Jan 1, 1969

By L. Delatour, K. Voltaire

This paper presents various aspects of the legal and economic settings that govern the exploration for mineral resources in Haiti.

Jan 3, 1979

By Edward I. Salkovitz

RECENTLY a set of crystallographic angles for bismuth was calculated and a standard (111) projection was constructed. Since these calculations

Jan 1, 1957

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada. 1935. GUILLAUME DANIEL DELPRAT Melbourne, Vic., Aust. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1933. KARL EILERS New York, N. Y. 1922. FEDERICO GIOLITTI Trino,Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER New York, N. Y. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDOAEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T. A. RICKARD..... Victoria, B.C., Canada. 1933. ALBERT SAIVEUR CAMBRIDGE, MASS.

Jan 1, 1937

PROF RICHARD ÅKERMAN Stockholm, Sweden DR. FRANK DAWSON ADAMS Montreal, Canada PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England PROF HANS HOFFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE POURCEL Paris, France DR. ROSSITTER W. RAYMOND New York, N.Y. DR. ING H. C. EMIL SCHROEDTER Dusseldorf, Germany JOHN E. STEAD Middlesborugh, England JAMES M. SWANK (Associate) Philadelphia, Pa. PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1917

CURRENT MATTERS Page Page New York Meeting : v 27th Engineers xl Year Book, 1918 v Professional Classes War Relief. x1i Minutes of Meeting, Board of W. S. S x1i Directors vi American Engineering Standards xlii President's Report vi Hadfield Prize xlv Local Section News: Members in Military Service... xlviii Columbia xiii Personal li San Francisco xiv Positions Vacant liii New York xvi _ Engineers Available liv Southern California xxxi Forthcoming Meetings 1v United Engineering Society xxxii Library...% lvi Engineering Council xxxv Membership lix Other Societies: Institute Committees lxxviii Mining and Metallurgical Soc- Officers and Directors lxxxvi iety of America xxxix

Jan 3, 1918

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1938. HENRY CORT HAROLD CARPENTER, London England 1933. KARL EIKERS New York, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1938. A.M. PORTEVIN Paris France 1937. JOHN V.W. REYNDERS, New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada

Jan 1, 1939

[Trans. No,PlaceDate Vol. Page1 1. Wilkes-Barre, Pa*May, '71 13 2, Bethlehem, Pa Aug., '71110 3, Troy, N. Y Nov., '71.. 113 4. Philadelphia, PaFeb,, '72.. 117 5, New York, N, Y.*May, '72,, 120 6. Pittsburgh, Pa Oct,, '72,, 125 7. Boston, Mass Feb,, '73.. 128 8. Philadelphia, Pa,*May, '73., 23 9. Easton, PaOct., '73., 27 10. New York, N, Y Feb., '74,, 211 11. St. Louis, Mo,*May, '74.. 33 12, Hazleton, PaOct., '74., 38 13, New Haven, ConnFeb., '75., 315 14. Dover, N. J,*May, '75.. 43 15, Cleveland, 0Oct,, '75,, 49]

Jan 1, 1928

PROF RICHARD ÅKERMAN Stockholm, Sweden PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England PROF HANS HOFFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France ALEXANDRE POURCEL Paris, France DR. ROSSITER W. RAYMOND New York, N.Y. PROF ROBERT W. RICHARDS Boston Mass. DR. ING H. C. EMIL SCHROEDTER Dusseldorf, Germany JOHN E. STEAD Middlesborugh, England JAMES M. SWANK (Associate) Philadelphia, Pa. PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1917

By Harold Cook

THE purpose of this paper is to state briefly the inspection requirements of the Bureau of Ordnance, the specifications governing the inspection, and the physical and chemical properties of the steel used in the construction of ordnance for our Navy. It would be of interest to evoke discussion on points in these specifications which do not tend to insure the production of the very best material for the purpose intended. In other words, what requirements of our specifications are useless and also in what manner are our specifications deficient? It might be well at the, start to answer the first criticism of this paper which will probably be made, and that is that the title does not agree with the subject matter. Considering metallographic work as covering only the macroscopic and microscopic examination of metals, this paper will have gone beyond the subject; but it is believed that a broader definition of metallography is that it is the study of the relation of the internal structure of metals and alloys to their composition and to their physical and- other properties. The internal structure of steel is dependent on its physical and its chemical properties. These physical properties are dependent on the chemical composition and the mechanical and thermal treatment of the steel. So it seems that this subtitle would not be entirely necessary and that the title "Metallography of Steel for Ordnance Purposes" would cover a study, not only of what we can learn of macroscopic and microscopic examination, but broadly of the whole subject of the specifications, the fulfillment of the requirements of which produce the structural conditions revealed by macroscopic and microscopic examination. .

Jan 2, 1916

By J. V. Richards

(Canal Zone Meeting, November, 1910,) THE Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present paper is to describe some of the more common Mexican dry-washing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt." This argo masa occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft.. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted pay-ground was high.

Apr 1, 1911

By John I. Yellott

SINCE the days of Newcomen and Watt, when men first sought to turn the energy of fuels to useful purposes, coal-generated steam has supplied most of the power needed for both stationary and mobile applications. The low efficiency and large water requirements of the nineteenth century steam-power plant caused many engineers to turn their thoughts toward more direct means of converting heat into power. As far back as 1791, John Barber secured an English patent on a combination' which he might well have called a "gas turbine." He proposed to generate procducer gas from coal or charcoal, to burn it under pressure in air obtained from a reciprocating compressor, and to drive a turbine wheel with the resultant hot combustion products. With the optimism characteristic of the inventor, he hoped that the turbine would not only operate his compressor but also perform useful work. There is no record that Barber ever built his machine, but if he had done so he would have learned that useful power can result from such a combination only when both turbine and compressor are highly efficient and when the temperature of the gas entering the turbine is not far below 1000°F. Hot-air prime movers continued to attract attention, and both Stirling in England and Ericsson in America2 built reciprocating engines that operated with some success upon coal-heated air. The internal-combustion engine, burning liquid fuels, supplanted the hot-air type, and, for the first time, challenged the supremacy of both the steam cycle and its familiar fuel, coal. LIQUID FUELS COMPETE WITH COAL As the increasing use of the automobile multiplied the demand for gasoline, the supply of residual fuel increased rapidly, and heavy oil declined in price to the point where it became competitive with coal. First in the marine field and later in stationary plants in areas adjacent to refineries, oil began to be widely used. Oil's greater convenience and higher heating value per pound of weight or per cubic foot of bunker space have caused it to take over much of the marine field. The introduction of the highly efficient diesel engine, capable of burning a fuel that is cheaper than gasoline, again threatened the position of coal, for the operating costs of the diesel became directly competitive with those of coal- burning equipment. In isolated power plants and smaller marine installations, the diesel provided the medium by which oil again successfully invaded fields formerly dominated by coal. The diesel engine, provided with an

Jan 1, 1946