Search Documents

By Lyle D. Randen

With the environmental movement beginning in the late 1960's came a deluge of permit requirements for the mining industry. Coal mining has been one of, if not the most, severely impacted of the mineral industries as a result of the passage of the Federal Surface Mining Control and Reclamation Act of 1977. Numerous provisions of this Act and numerous regulations developed under authority of the Act are being challenged in differing levels of the judicial system across the United States. Such court cases have had varied success. Numerous other regulatory programs that are not quite as dramatic as the SMCRA have presented an unending regulatory problem for mining operators. My comments in this presentation relate primarily to the major Federal and State agencies and their legal responsibilities which we in the coal mining industry must address in order to receive authority to construct and operate surface coal mines in the State of Wyoming. A list of the Federal and State agencies one could deal with in an application is as follows: 1. Bureau of Land Management (BLM). BLM is responsible for deciding where and when to lease federally owned coal and for establishing terms and conditions for leases. BLM also has some control over surface reclamation on federal land, i.e. regrading to eliminate highwalls, covering of spoils, maximum extraction of coal to limit future disturbance, contemporaneous reclamation, etc. BLM is also responsible for designation of federal lands unsuitable for all or certain types of surface coal mining operations. 2. Geological Survey (USGS). USGS coal mining responsibilities apply only to Federal and Indian lands and concern compliance with production requirements including diligent development, minimum production levels, royalty payments and resource protection, and

Jan 1, 1983

By E. P. Klier, Volker Weiss, George Sachs

IT has been shown that the isothermal transformation of austenite in a special steel can be modified by isothermal holding in the high subcritical transformation range.' Since this treatment potentially leads to increased hardenability, limited testing has been completed to determine if the stabilization effects observed with this treatment can be used to advantage in the heat-treating of 4340 steel. As an index of the effects of the several austenitizing treatments on the hardenability of the steel, Jominy-type hardenability tests were completed for specimens 2.5 in. in diameter and 8 in. long. Since the steel studied is to be used at strength levels where notch sensitivity is of major concern, notch sensitivity after selected austenitizing treatments has been evaluated by notch tensile tests for several specimen sizes. The steel composition and the austenitizing treatments are given in Table I. The test specimens are presented in Fig. 1. The hardenability data are given in Fig. 2 and the notch tensile properties are presented in Fig. 3. The hardenability of the steel investigated when determined by use of the standard Jominy test specimen2 as high and remained essentially unchanged for the different austenitizing treatments. For the larger test specimen, as has been shown by other investigations," the characteristic hardenability indexes are changed and it becomes possible to isolate austenitizing treatments which promote maximum hardenability. The stepped austenitizing treatment promotes higher hardenability as is indicated in Fig. 2. The evaluation of notch sensitivity for very high strength steels is best accomplished by means of the notch tensile test. The experimental conditions of the test, however, modify the notch strengths measured, and in the present experimentation an effort was made to achieve a limiting notch condition by fixing the notch root radius at 0.001 in. while the specimen diameter was allowed to increase from 0.3 to 1.1 in.* For this root radius the notch strength, 0.3-in.-diam specimen, and this trend differs from that for the larger specimens. At the highest tempering temperatures the 1.1-ip.-diam specimens yield comparable results for the austenitizing treatments compared. However, as the tempering temperature is progressively lowered below 800°F, em-

Jan 1, 1958

By Roy Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By David J. Dunn

At a time when mill availability is at a premium, production costs are rising, and lead time for mill liner casting is a year or more, mill liner design is an important factor in ore grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, reduce liner wear rate, and lengthen liner life. The mill liner that grinds best, lasts the longest, and costs the least is a necessity for economic mill operation. After testing four mill liner profiles for 3.96 X 3.65-m (13 x 12-ft) overflow ball mills, Climax Molybdenum Co. found that an improved design increased mill tonnage by 2.72 t/h (3 stph) while reducing finish grind by 1.7% minus 100-mesh, reduced liner wear rate, and almost doubled liner life.

Jan 12, 1976

By A. D. Bryant

APPROXIMATELY 2 1/2 million tons of silica sand and ground silica with a value of $7.25 million is produced annually from the Ottawa, Illinois, district. These silica products come from the well known St. Peter sandstone formation which covers part of the Mississippi Basin extending from St. Paul on the north to the central part of Arkansas on the south and from Muncie, Ind., on the east to Kansas City on the west. Practically the whole state of Illinois is underlain by this formation except where removed by erosion. Sand produced from the St. Peter sandstone in the Ottawa district is noted for its purity, uniformity, and quality. In addition to various screened grades for industry about 10 pct of the total production of the Ottawa district is ground into silica flour for use in glass, abrasives, enamel, porcelain, tile, for foundry and filter sand, and other uses.

Jan 3, 1953

By Walter Miller

A surprising development during the year was the continued high demand for petroleum products and the high level of crude oil charges to the stills. Generally speaking, the petroleum industry during 1946 succeeded in producing a greater quantity of crude oil and petroleum products than in any of the war years, and considerably exceeded the production of any prewar year. Daily crude still charges averaged between 4,700,000 and 4,800,000 bbl per day for 1946 and about equaled the 1945 record, although most pessimistic 1945 guesses, predictions, or fears ranged, for 1946, from only 3,900,000 to 4,400,000 bbl per day. In spite of the high crude charge to the stills, total stock of crude oil was higher at the end of the year by some 7,000,000 to 8,000,000 bbl. A similar story holds regarding stocks of the principal refined products. Gasoline on hand at year's end was two to three million barrels lower, and was considered low for the expected demand during the coming high consuming season, while stocks of light and heavy fuel oils, although some higher than a year previous, hardly reached a comfortable level. The trend in gasoline of high octane number, which has resulted in a marked rise in. the antiknock quality by the end of 1945 (five or six numbers higher than during the war and one number higher than the prewar quality of civilian motor gasoline of 1941) was abruptly arrested by an acute shortage of metallic lead for manufacturing tetraethyl lead. Government action in the form of lead price control, rationing, and the setting of octane ceiling specifications to conform to the reduced ethyl lead compound available were enforced until abrogated at the end of the year. It will be interesting to see how rapidly the octane levels will resume the rising trend, as more metallic lead slowly becomes available for making greater quantities of ethyl lead compound. As octane quality rises over present levels the disadvantage of the refiner without catalytic cracking equipment will increase. Gasoline made by catalytic cracking, without addition of ethyl lead, approximates 77 octane by the official ASTM Motor Method test, compared with 66 for gasoline generally similar in volatility made by the older thermal cracking operation. Catalytic gasoline shows an even greater improvement in the Research octane number, the comparison being roughly 86 Research versus 71 Research octane for the thermal cracked product. This higher differential in Research octane is credited by many, although not universally so, as contributing to better road performance, and consequently resulting in a more desirable product marketwise. In some parts of the country a premium of roughly one fourth cent per gallon is now being paid for gasoline with higher Research octane made possible by including catalytic cracked product in the final blends. If such price differentials in favor of catalytic gaso-

Jan 1, 1947

By Walter Miller

A surprising development during the year was the continued high demand for petroleum products and the high level of crude oil charges to the stills. Generally speaking, the petroleum industry during 1946 succeeded in producing a greater quantity of crude oil and petroleum products than in any of the war years, and considerably exceeded the production of any prewar year. Daily crude still charges averaged between 4,700,000 and 4,800,000 bbl per day for 1946 and about equaled the 1945 record, although most pessimistic 1945 guesses, predictions, or fears ranged, for 1946, from only 3,900,000 to 4,400,000 bbl per day. In spite of the high crude charge to the stills, total stock of crude oil was higher at the end of the year by some 7,000,000 to 8,000,000 bbl. A similar story holds regarding stocks of the principal refined products. Gasoline on hand at year's end was two to three million barrels lower, and was considered low for the expected demand during the coming high consuming season, while stocks of light and heavy fuel oils, although some higher than a year previous, hardly reached a comfortable level. The trend in gasoline of high octane number, which has resulted in a marked rise in. the antiknock quality by the end of 1945 (five or six numbers higher than during the war and one number higher than the prewar quality of civilian motor gasoline of 1941) was abruptly arrested by an acute shortage of metallic lead for manufacturing tetraethyl lead. Government action in the form of lead price control, rationing, and the setting of octane ceiling specifications to conform to the reduced ethyl lead compound available were enforced until abrogated at the end of the year. It will be interesting to see how rapidly the octane levels will resume the rising trend, as more metallic lead slowly becomes available for making greater quantities of ethyl lead compound. As octane quality rises over present levels the disadvantage of the refiner without catalytic cracking equipment will increase. Gasoline made by catalytic cracking, without addition of ethyl lead, approximates 77 octane by the official ASTM Motor Method test, compared with 66 for gasoline generally similar in volatility made by the older thermal cracking operation. Catalytic gasoline shows an even greater improvement in the Research octane number, the comparison being roughly 86 Research versus 71 Research octane for the thermal cracked product. This higher differential in Research octane is credited by many, although not universally so, as contributing to better road performance, and consequently resulting in a more desirable product marketwise. In some parts of the country a premium of roughly one fourth cent per gallon is now being paid for gasoline with higher Research octane made possible by including catalytic cracked product in the final blends. If such price differentials in favor of catalytic gaso-

Jan 1, 1947

By K. Thirumalai

Rock response to heating depends on properties of rock material and varies widely between different rock types. By dissipating energy, surface melting limits rapid heating and fragmentation of rocks achieved by surface heating methods. This study advances a concept of rock fragmentation by rapid internal heating of a localized inner volume of rock. The working of the method to achieve fragmentation of rocks (Charcoal granite and Dresser basalt) having poor response to surface heating is analyzed. Experimental data on elevated temperature rock properties required for the study are presented. Based on the properties of test rocks, a high frequency (50 MHz) dielectric heating method of generating localized internal heating was selected for experimental study. The test rocks were fragmented without melting under localized heating below 600ºC. The heated volume required for fragmentation was observed to be less than 2 percent of the test block volume. A practical application of the method for in situ fragmentation of rocks is suggested.

Jan 1, 1971

By L. G. Austin

The procedure for scaling breakage parameters determined in a laboratory mill to values for a full-scale mill is briefly presented. A simulation model of a closed circuit mill also requires a model of residence time distribution, a mass transfer law to predict over-filling as a function of flow rate through the mill, and a model to describe classification action. For fine dry grinding, or viscous slurry grinding, it is necessary to allow for slowing-down of breakage rates for a fine mill charge. Four examples of comparing simulation models to actual plant data are presented. The first is wet grinding of copper ore in normal closed circuit at 50 tph (metric) production, under conditions where the mill does not overfill. The second is the wet grinding of copper ore in reversed closed circuit at production of 87, 102 and 108 tph, with flow through the mill of approximately 150, 200 and 300 tph. The third is dry grinding of coal with a hot air sweeping stream to remove all of the coal as air-borne material, in open and normal closed circuit. The fourth is grinding of cement clinker in a two-compartment, air-swept tube mill in normal closed circuit with two different classifiers, producing 120 tph of 3250 Blaine cement. In all cases the simulated capacities and product size distributions were in reasonable agreement with actual plant performance.

Jan 1, 1984

By P. Barnes

THE complete and accurate filtration of water (if the word ,accurate may be thus used) for the feeding of boilers, and for many similar industrial purposes, although somewhat practiced both at home and abroad, has been by no means common. Even if the exact line cannot be defined at which filtration begins to be called for, and will be found profitable, it is certain that in a large number of cases it may be employed with real advantage in the economy of fuel, and also in. the greater durability of the boiler or other form of apparatus in

Jan 1, 1882

By Jon Kogut

This paper describes three programs, currently in use within MSHA, for graphic analysis of accident frequency data. The first program, TREND, plots confidence bands for curved trends in data compiled over a period of time. In addition to detecting statistically significant upward or downward trends, the program can be used to determine whether an observation at a particular time deviates significantly from the historical pattern. The second program, POIPORP, plots interval estimates for the risk of accident in each of several environments, given an observed number of incidents and exposure time at each environment. POIPORP is designed to quantify the uncertainty implicit in incidence rates based on limited information and to facilitate statistically valid comparisons among the rates. The third program, CINDY, plots dynamically adaptive control charts for accident or injury experience at a given location. These charts are used to detect statistically significant departures from a changing standard or a previously established trend. All three programs are written in FORTRAN IV, utilizing DISSPLA and IMSL. They exemplify forms of statistical analysis that would not be practical without a computer. Use of the programs is illustrated with applications to coal mine fatality and injury experience.

Jan 1, 1983

By B. J. Kochanowsky

The primary use of a portable crusher, i.e., a crusher mounted on crawlers or tires, in the rock and mining industries is to reduce costs by permitting the substitution of conveyor belt haulage for truck or track haulage. The usual sequence of operations in surface mining is drilling, blasting, loading, haulage, and crushing. Haulage is normally accomplished by truck or track-mounted cars, the latter method being used for the longer distances. However, by using a portable crusher in the pit, the sequence of operations would be changed so that the crushing stage would occur before haulage (Fig. 1). Such a sequence would permit the use of conveyors to replace the more expensive truck or track haulage methods. Since most quarry and open pit operations normally require a crushing stage, the only additional costs incurred will be due to the investment required to purchase or construct a mobile arrangement for a crusher. But this factor has to be weighed against the advantages to be gained by conveyor haulage. As shown in Fig. 2, transportation of material by belt conveyor over short distances is less ex- pensive than by truck. The inclination of the belt has no effect on belt speed; consequently, the hourly tonnage moved remains the same. Conversely, the output rate of trucks as expressed in tons or ton- miles per shift decreases proportionally to the haulage speed, which is considerably slowed by the steepness of the road (Fig. 3a). Although maximum possible grades and maximum economic grades of haulage are greater for a belt than for a truck (over the same total lift), the longer haulage distances favor the use of trucks.

Jan 12, 1960

By S. K. Kawatra

The paper describes a system for on-line analysis of ash in solids in coal slurries for coal cleaning operations. The system consists of two sensors: 1) gama density gauge, and 2) ash sensor. The operational characteristics of each sensor are discussed.

Jan 1, 1980

By R. E. J. Putman

Introduction Self-tuning regulators are a class of controllers built around the concepts of sampled data theory, and are especially suitable for implementation in a digital microprocessor or minicomputer control system. The algorithms used are distinctly different from those based upon analog control techniques and include automatic adjustment features which permit them to adapt to unmeasured changes (in, for example, ore grindability) or process nonlinearities (as exhibited by cyclone classifiers). They are also designed to handle transport lags in a simple manner, for example, anticipating the effects of a variable recycle rate on particle size distribution. The advent of distributed control systems will encourage the exploration of these techniques in the minerals processing industries, and particularly for improving the control of comminution circuits, which are especially energy intensive. This paper outlines some current work in progress on this topic. Background Those engaged in the practice of process control have long had two philosophical problems for which solutions have been actively sought - what is optimal control and how can we attain it in some heuristic fashion automatically. The basic analog controller can be represented by the differential equation: [V = Ko + K1 f y • dt + K2 dt(1)] where: v and y are the instantaneous values of output and error respectively and K0, K1, and K2 are tuning constants. The empirical rules for establishing the values of K0, K1, and K2, which provide stability, have evolved from the initial suggestions of Ziegler and Nichols(9) in 1942 and have served their purpose well. However, later analyses demonstrated that there are in fact many combinations of the values of K0, K1, and K2 which, besides being stable, behave better or worse in relation to other process control criteria; some examples are duration of error, amplitude of a damped response, magnitude or rate of movement of control valve or adjustment of speed regulator, etc. The definition of optimality had broadened. In 1964, Kalman(4) published his classic paper which tried to resolve these problems. He defined a

Jan 1, 1982

J. C. WRIGHT.-The problem of organizing and maintaining a vocational class for those employees who are engaged in the mining industry depends on several most important factors. The first is the sympathetic cooperation of employer and employee; the second is to find the subject matter that must be presented to these men; and the third is to find the instructor who can present that subject matter. This is perhaps the most difficult, for we usually find a man who knows the material that is to be presented but is not a teacher or does not know how to organize his material. The man must know the subject matter from the standpoint of absolute contact with industry in order to be a successful teacher. I have come into contact with two kinds of schools organized in connection with mining occupations. In one type the instruction leans very largely toward elementary subjects, arithmetic, reading and writing and spelling; it is not of such a character as to help or improve the working man in his occupation in the sense that we are attempting when we speak of vocational education. In the other type of school, an engineer is usually employed as a teacher. He immediately begins to give the things with which he is most familiar and the instruction becomes such as only those who possess a high-school or college education, perhaps, are able to receive. In between these two schools is the school we are trying to, promote, a school that will meet the needs of those employed. MARGUERITE W. JORDAN,* Altoona, Pa. -Vocational education has become the business man's problem; for he is the keeper of that white elephant, labor turnover, and anything that will decrease the size of the monster is worthy of serious consideration. This vocational education can do; for it can supply many of those deficiencies in upbringing and. environment that make for the discontent and restlessness of our varied classes of unskilled labor: the Anglo-Saxon mountaineer; the Southern negroes who have crossed Mason & Dixon's line by the thousands, "searching satisfaction for our minds;" and the still greater number who have sought across the sea America, "the promised land.

Jan 4, 1919

By Mark R. Lamb

The recent growth of a sentiment among cyanide-plant designers against the use of gravity-stamps for the crushing preliminary to cyanidation may be said to date from the almost simultaneous perfection of the ribbed tube-rnill liner and of the tall, air-agitation tank. The first step in the resulting change of practice mas the universal adoption of the tube-mill for fine-grinding and the use of coarse screening on the battery. This was the beginning of the surrender of supremacy by the gravity-stamp; since merely the single fact that it was a more economical machine for crushing fine had retained it in favor as conlpared with ball-mills, rolls, or steam-stamps. The surrender, however, is not yet complete.

Jan 1, 1911

By Charles J. Speake, Dennis R. Haley, Thomas E. Finch

The tremendous interest in development of surface- mineable coal throughout the western US will bring with it a requirement for many manhours spent in mine planning and equipment selection. One problem in particular that engineers face during the planning stage is that of selecting a dragline with the proper reach capability. Reach, expressed in terms of operating radius and effective spoil radius, can be a major problem when mining deeper than originally planned, and aside from production requirements, the ability of a particular dragline to spoil across a strip is essential. Determination of dragline reach needed for a multiple-seam western coal operation can be simplified by use of an equation derived below that eliminates the need for tedious and repetitive calculations.

Jan 5, 1977

By C. A. Heiland

THE Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an, equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station, whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of 100 meters, as under most circumstances it is difficult to level along a larger concentric circle about the station.

Jan 1, 1928

By C. A. Heiland

THE Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station; whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of 100 meters, as under most circumstances it is difficult to level along a larger concentric circle about the station.

Jan 1, 1928

By Bension Varon

Systematic projections of mineral supply, demand and prices are an integral part of the mineral sector planning process. As such, their primary value is not as prophecies but as devices for imposing discipline on thinking about the future and as means of ensuring consistency in policy decisions. Both the present and the broad outline of the future as presently discernable affect projections on specific minerals. The present world mineral situation reflects most prominantly the recent commodity cycle while our view of the future is largely shaped by perceptions and attitudes of policy-makers and the public over larger issues. Mineral commodities are of considerable importance to various countries. This in itself dictates a strong interest in systematic projection activities, the need for which is heightened by the volatility of certain basic variables affecting mineral demand in the world. It is useful for presentation purposes to discuss the various techniques suited for projecting mineral trends under three principal headings, viz., econometric modeling, systems analysis and technological forecasting. In addition, two specialized variants, input-output analysis and resource base modeling, are discussed. In each case, a brief description of the approach and some indication of its application to projections of mineral commodities are provided.

Jan 1, 1977