Search Documents

By James R. Swaisgood, Ronald E. Versaw

Hundreds of shafts have been sunk in the United States in the past. Most of these have been successful however, in some instances thousands of dollars have been lost due to work stoppage while emergency measures were taken to control unexpected water flows. In cases where it was not possible to control the water, the shafts were completely lost. Many thousands of dollars have also been wasted in overconservative support design for the successful shafts. These "hell for stout" designs were necessary because of the importance of the shaft in the operation of the mine. If there was trouble in the shaft, all underground operations would come to a halt. Over-design was also necessary because no reliable preconstruction investigation methods or rational support design methods were available.

Jan 6, 1974

By John D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space.

Jan 9, 1959

By W. A. Bruce

THIS paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to sell-spacing problems are shown.

Jan 1, 1942

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

Beyond the industrial suburbs of Melbourne to the southeast are brown coal deposits just under the fertile soil of the Latrobe Valley. These deposits rank as one of the wonders of the world. The manner in which this resource is put to use is one of the great engineering accomplishments of our time and also a prime example of Australian elan. The brown coal, with over 60% water content, occurs in beds from 200 to 400 ft thick, under 50 ft of cover. Fifty thousand tons of coal per day move in a nearly continuous stream from mining face to boilers. The power plants supply two thirds of the State of Victoria's requirements, about 800 megawatts. Surge capacity between mine and power plant is sufficient for 12 hr steaming time! Victorian brown coals have been known since the middle of the 19th century. However, it took a strike of bituminous coal miners in 1915 to bring brown coal permanently into the picture as a fuel for power generation. In Australia, power generation is a State function. The great development of brown coals has been under the State Electricity Commission of Victoria.

Jan 10, 1964

ASSETS Working Fund Assets Cash-unappropriated $62,41294 Members' 1951 dues receivable 14,336 98 Accounts receivable Advertising, publications and miscellaneous $43,22055 Less-Reserve for delinquent accounts 12,775 76 $30,44479 Petroleum Branch-Special Projects Fund¬ Advances re Petroleum Conservation Volume 5,37085 35,81564

Jan 1, 1952

By Robert M. Doerr

A method, based on radial distribution analysis, was developed for determining the effect of size to which a given ore is broken on the potential recovery in beneficiations targeted to selected concentrate grades. A measuring microscope and computer analysis are used to obtain the radial distribution of the valuable component in polished sections of ore.

Jan 1, 1975

By authority of the Secretary of War, and in response to frequent requests, the following suggested list of reading is issued by the War Department for the information of civilian engineers desiring to inform themselves on military subjects: These references have been selected, first, with a view to giving to engineers unfamiliar with the art of war a general survey of that sub-

Jan 1, 1916

By Sherwin Kelly

THE need for geophysicists to adopt a uniform mode of expressing the electrical resistivity of geological formations has been stressed by Dr. A. S. Eve.1 The present paper is to emphasize the point he raised, to bring the weight of disinterested authority to bear on the matter, and to urge the adoption henceforth, save in exceptional cases, of a standard expression for resistivity; all in the hope that the needed reform will thus actually be brought about. The general definition of the resistivity of a material is the resistance in ohms between two opposite faces of a unit cube of that, material. No account need be taken here of the cases in which the unit volume is not a cube, and the units of length and cross-section are different, encountered principally when dealing with metallic conductors such as wires. The idea of the resistance of a unit volume of earth or rock has found expres-sion in geophysical literature in a number of forms and with a variety of units. Fortunately, the metric system has been adhered to in most cases, so ordinarily the meter or the centimeter, usually the latter, has been the measure chosen. The resistivity is then the resistance of a cube of the given rock, or soil, one centimeter on, an edge. This is far from always being the same thing, however, as the resistance of a cubic centimeter. A long thin wire could contain a cubic centimeter and have a high resistance, whereas the same volume formed into a flat plate would have an entirely different, and quite low, resistance between faces. Con-sequently, it is not proper to express resistivity in ohms per cubic centi-meter, inch, etc., as has been done occasionally by .some writers. In an effort to emphasize the idea of cubic volume, some geophysicists, the writer among them, have used the phrase, ohms per centimeter cubed. This is a graphic way of picturing the measure, but is not in favor among highly qualified authorities. In this connection, an appeal was made to the U. S. Bureau of Standards for advice, and the Director, George K. Burgess, kindly replied in detail as to the practice adopted by his Bureau: ." . .' such expressions as ohms per centimeter cubed' or any similar expressions are objectionable, because they certainly carry the implica-tion that the resistivity is found by dividing ohms resistance by the volume in cubic centimeters." Actually, of course, resistivity is found

Jan 1, 1932

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

Time Now For Thinking In these turbulous times a natural restiveness is created among the younger men of the mining profession. Many of them are veterans of World War II and the question is raised in their minds as to whether or not to go back into military service. There is time to think about this question now and it is advisable to do so in order that snap decisions may be avoided if war is declared.

Jan 2, 1951

By John C. Robison

INTRODUCTION Sensitivity analysis is a means of gauging the impact of individual risks on a financing. Key risks can occur in three time periods: - Feasibility, engineering and construction phase; - Start up phase (usually through completion); - Operating phase (post completion). If a company has agreed to cover these risks prior to completion, then less attention will be paid to the sensitivity of the project in the first two time periods. Since the operating phase of the project generates cash for both operations and debt service and generally does not begin until two to six years after the loan is signed, it is wise to look at scenarios other than the projected "base-case" scenario in order to determine the project's capability to operate successfully under a broad range of probable future events. Lenders are compensated at a fixed spread over their borrowing base and generally are not compensated if the project is successful beyond expectation. They are also subject to the loss of principal plus funding costs if the project performs below expectation. Because of this, lenders establish sensitivities around the parameters of conservative projections developed in the project feasibility studies and the cash flows resulting from these projections. The initial cash flow projections should demonstrate the project's ability to meet cash costs, debt service requirements (principal and interest), and still have sufficient cushion to cover contingencies such as strikes, price fluctuations, force majeur situations, etc. (See Schreiber, Chapter 10). The selection of the level of sensitivity analysis to be performed is the result of both objective criteria, including probabilistic analysis applied to the technical parameters, and, of equal importance, subjective criteria applied by the analysts, especially with regard to the economic and financial parameters impacting the project cash flows. RISK SENSITIVITY Assumptions used in the cash flow projections should be realistic. Risks identified by the lenders should be identified and cash flows prepared to assess whether these project risks are acceptable. Typical project risks include the following (see also Chapter 9): - Sufficient reserves - quantity and quality - Product price - Production level - Operating costs - Availability of energy and supplies - Transportation and infrastructure requirements and costs - Interest rate - Completion risks - Tax level - Political risks - Cost over-run risks - Operator experience - Management - Technological risks - Environmental permits and risks - Foreign exchange risks - Insurance coverage - Equity of sponsors - Inflation rate - Capital expenditure during project life In order to see the effect on the cash flow projections, each risk should be analyzed for its impact on the cash flow generating capacity of the project. Sensitivities can be examined to see if the resultant cash flow projection will meet the lenders minimum credit standards. 1.Reserve Sensitivity In general, lenders will not assume the reserve risk. However, it should also be noted that lenders receive loan proposals in which reserves range anywhere from proven to possible. Sensitivities are not generally run for various reserve levels and reserve estimates are either considered acceptable or not acceptable by the lenders.

Jan 1, 1985

By Fred A. Anderson, George B. Wallace, Edward J. Slebir

Auburn Dam will be a thin, double-curvature concrete arch dam about 685 ft high. With a crest length of about 4000 ft, it will be the world's longest single-arch dam. The site is located on the North Fork of the American River about 40 miles northeast of Sacramento, Calif. Construction is scheduled to get under way in 1970. In planning for the design and construction of Auburn Dam (see artist's conception), the foundation material, with its various discontinuities, is being investigated and the structural characteristics of the rock mass evaluated. The investigation and testing programs will aid in defining the pertinent geologic features and their individual and cumulative influence on the foundation. The work includes geologic surface mapping, surface trenching, core drilling, geophysics, tunneling, excavating shafts and raises, performing in-situ tests, and conducting laboratory tests on core and block samples. Competent amphibolite is the predominant material in the foundation, but significant bodies of chloritic, talcose, and metasedimentary rocks, a strongly developed jointing pattern, faults, and shear zones also affect the deformability of the rock mass. A comprehensive rock mechanics program, closely coordinated with geologic investigations as well as the engineering studies, therefore is required The rock mechanics work is a combination of many analytical studies and experimental investigations. The experimental work includes laboratory tests on core samples from holes drilled for geological studies of the entire foundation and in-situ tests performed in selected areas. The laboratory testing program evaluates the general properties of all important rock types and aids in correlating many of the key structural features encountered within the foundation. To derive maximum benefit from the field tests, they are conducted in materials which represent a

Jan 1, 1970

By G. J. Cardwell

The rock and mineral analyst will be called upon to determine both the major and minor constituents in materials as varied as rocks, soil, sediments, concentrates and various liquids. These analyses will have interactions requiring extraction, matrix modification, and background correction. Analytical methodologies include classical gravimetric methods, such as fire assay, emission spectroscopy, X-ray fluorescence, atomic absorption, inductively coupled plasma, and neutron activation. With these capabilities the analyst can be called on to determine three-fourths of the elements in the periodic table. How can the earth scientist pick the method best suited for his particular sample?

Jan 1, 1984

By Roswell Johnson

THE prevailing system of wells on a rectangular basis, as shown in Fig. 1-A, has developed because of the exigencies of offsetting at boundary lines. When, however, a very large tract is, being drilled, it is often possible to abandon this inferior method for the superior arrangement C- PROPER STAGGERING FIG. 1.-THREE SYSTEMS OF SPACING WELLS. known as "staggering," which is illustrated in Fig. 1, B and C. The advantages of the triangular over the rectangular method are evident from Fig. 2, computed on the basis of one well to 10 acres (4 ha.). With the triangular system, no land is more than 409.4 ft. (124.8 m.) from a

Jan 8, 1918

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples.

Jan 9, 1959

By J. C. Osler

The design of a tailings dam is a geotechnical engineering project of considerable scope. For the design, it is necessary to establish the engineering properties of the soil or rock strata which will support the dam and the tailings or other fill which will be used to construct the dam. The various field and laboratory investigations which are necessary to obtain the required design parameters are discussed in the paper and the use of these parameters to compute stability, settlement, and seepage are considered. The designer of a tailings dam can never assume an absolute knowledge of the properties of the foundation strata. Further, initial design assumptions are often approximate, particularly with regard to the distribution of pore pressures through and beneath the dam. Thus, the installation of performance monitoring instruments is recommended, since data obtained from such instrumentation can be used to check the stability of the structure both during construction and after its completion.

Jan 1, 1972

By George Otis Smith

The Secretary of the Interior in his recent report to the President has defined the new public-land policy, which is in fact "but a new application of an old policy." His words may be more acceptable on this subject of land classification than the repetition of phrases which have served some of us for several years. Secretary Lane says of the past: 1'Congress has always been most generous as to the disposition of the national lands.... There was land for all, and it was the government's glad function to distribute it and let those profit who could.... And this generous donor was not so petty as to discriminate between kinds of lands, the uses to which they could be put, or the purposes which those might have who got them. Land is land, save when it contains minerals; this was roughly the broad principle adopted. To classify was a task too difficult or not worth while. The lands would classify themselves when they arrived in individual ownership. And so the door was opened for monopoly and for fraud." Of the reaction and the evolution of a new policy, the Secretary con. tinues: • ' " A reaction was inevitable. If lands were to be withdrawn from public service, why might not the government do the withdrawing itself? The old philosophy that land is land' was evidently unfitted to a country where land is sometimes timber and sometimes coal; indeed, where land may mean water—water for tens of thousands of needy neighboring acres. For the lands of the West differ as men do, in character and condition and degree of usefulness. We had not recognized this fact when we said 'land is land.' Lands fitted for dry farming and lands that must forever lie unused without irrigation; lands that are worthless save for their timber; lands that are rich in grasses and lands that are poor in grasses; lands underlain with the non-precious minerals essential to industry or agriculture; lands that are invaluable for reservoir or dam sites— these varieties may be multiplied, and each new variety emphasizes the fact that each kind of land has its own future and affords its own opportunity for contributing to the nation's wealth.

Jan 1, 1915

By WALDEMAR T. SCHALLER, EDWARD P. HENDERSON

THE material available for mineralogic study, consisted of drill cores, 2 to 3 in. thick, supplemented by small well cuttings. Such study has added no essential new information regarding the minerals, though the refractive indices, used for determinative purposes, have been determined more accurately than before, permitting the development of a scheme for the rapid identification of these minerals. The essential points brought out by the investigation are two: (1) that certain mineral associations evidently point the way to an understanding of the geologic history and (2) that a definite sequence of mineral formation has taken place so that the original minerals formed have been in part-reacted on producing new compounds and associations; Twenty minerals have been found. The most important are :

Jan 1, 1929

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985