Search Documents

By Nicholas S. Young

The one million ounce Newrnont Gold loan has focussed attention on gold's new role as a financing vehicle. This paper explains the background of the new role for gold, and details various gold denominated products now available to the mining industry. The discussion highlights the importance of gold-based products, and how they should be used in developing business strategy for gold mining companies. [ ]

Jan 1, 1990

For the third year in a row total value of the Nation's mineral production broke all previous records. A new peak of $20.4 billion was reached in 1964. So says the U. S. Bureau of Mines. The Bureau's preliminary estimate for 1964 is $800 million higher than the value reported for 1963, and $1.6 billion greater than the 1962 figure. The unprecedented demand for minerals, has stimulated development of new mines and expansion of processing capacity in many parts of the country.

Jan 2, 1965

By F. J. Schuh

The drilling industry long has been plagued by failures in the bottom few joints of surface and intermediate casing strings. This paper presents an analysis of the various possible causes of failure and concludes that failures are caused by short-lived, high-energy torque impulses delivered from the drill string through the bit while drilling out the cementing plugs, cement and floating equipment. The magnitude of these torque impulses is shown to be a function of the rotational momentum of the drill string, and a method is derived to calculate the magnitude of these impulses. The available methods of strengthening the bottom joints are reviewed. It is concluded that, while present methods are ineffective, a combination of improved procedures for strengthening and minor restrictions on drillout practices will prevent failures. Introduction In most cases, failure in the bottom few joints of casing strings is not discovered until electric logs record that the bottom one, two or three joints have parted from the casing string and slipped down the hole. However, in some cases the parted section of casing uncovers a high-pressure or lost circulation zone, or shifts laterally restricting the passage of drilling equipment. In these instances extensive remedial work is required to realign the parted pieces and seal the exposed formations. Several methods used to strengthen the bottom joints of casing strings include locking set screws in the couplings, putting wedges in special collars, welding straps across the couplings, welding the couplings and, most recently, using epoxy resin-based, thread-locking compounds. Since none of these techniques has eliminated the problem, this study was initiated to find the cause of failures and to evaluate the available methods of prevention. Mechanics of Casing Failures An analysis of the various possible causes of failure indicates that the casing is unscrewed rather than broken and that therefore failure must occur before the shoe is drilled. Since there is no general agreement as to the causes of casing failure, some possible mechanisms were ATLANTIC RICHFIELD CO. DALLAS, TEX. considered in this analysis. Failure of the bottom joints of casing can occur by only one of three types of stress: tension, torsion or bending. The possible mechanisms of failure were evaluated by determining the forces required to cause casing failure by each of the stresses; and, where applicable, the possibility of failure by fatigue was considered. For casing to part under tension requires a downward load of more than the tensile strength of the casing. The lightest API weight H-40 grade casing requires a bit load on the bottom of the casing of 27,000 to 34,000 Ib per inch of bit diameter (Table 1). Since maximum drill collar weights seldom exceed 10,000 Ib per inch of bit diameter, it is apparent that casing strings cannot be parted by the downward load of the drill string. The second mechanism considered was failure by bending. This mechanism requires that the lowermost casing joints be free to be deflected laterally until the bending stress exceeds the strength of the pipe. To fail, the casing (at a height L above the shoe) requires a force and deflection' at the shoe of To deflect the casing shoe with the drill string obviously requires a dog-leg at the casing shoe. This dog-leg must have a rate of change equal to or greater than the change in curvature of the deflected casing, which is given by

Jan 1, 1969

By R. F. Hehemann, R. H. Goodenow

Thermal arrest, hot-stage microscopy, and transtnission electron microscopy techniques have been employed to study the transformations in low-carbon iron and Fe-9 pct Ni alloys. In continuous cooling experiments, each alloy transforms at an essentially constant temperature for cooling rates below the critical rate required for martensite formation. However, high-tenzperature transformation in pure iron takes place by a different mechanism than that in the 9 pct Ni alloys. Pure iron exhibits an equi-a a structure with a low and random dislocation density while the 9 pct Ni alloy exhibits a cell or lathlike substructure analogous to that of low-carbon martensite. This same substructure characterizes upper bainite in higher-carbon inaterials. UNTIL relatively recently, diffusionless transformations have been considered to take place by the same mechanism and have been termed mar-tensitic transformations.l-3 The most characteristic feature2 of this mode of transformation is the shape change produced by a shear deformation and growth of the product phase frequently occurs at an extremely high velocity approaching that of an elastic wave.4'5 A different mechanism of diffusionless transformation was recognized first in Cu-Ga and other copper-base alloys.6,7 From the absence of surface tilting in these alloys, it has been concluded that transformation is not accomplished by the cooperative shear displacements that occur in mar-tensitic reactions. Transformation presumably takes place by the rapid movement of an incoherent interface which is capable of propagating across parent grain boundaries. Although the transformation is diffusionless in the macroscopic sense, advancement of these interfaces is accomplished by an atom by atom rearrangement. Transformations of this type therefore require thermal activation and are generally operative only at high temperature. Although requiring short-range diffusion at the interface, propagation still occurs so rapidly that the reaction cannot be suppressed with normal cooling rates.7 The resulting microstructures exhibit large, irregular-shaped regions of the product phase, which are essentially free of crystallographic features. Consequently, these reactions have been termed massive transformations. Transformation by the massive mechanism has been reported to occur in ferrous systems involving pure iron and binary alloys of iron with nickel, chromium, and silicon by Gilbert and owen.' The Fe-Ni system is of special interest in that the massive transformation was observed in alloys with less than 15 pct Ni while alloys having more than about 28 pct Ni transformed by the conventional mar-tensitic mechanism. By employing cooling rates substantially higher than those used by Gilbert and Owen, Swanson and Parr have been able to suppress the massive transformation in alloys with 0 to 10 pct Ni9 and produce martensite as revealed by surface relief. The massive transformation in the alloys having less than 15 pct Ni was identified by the lack of surface relief and an irregular rather than clearly acicular microstructure.' Speich and Swann, using thin-foil electron microscopy, identified three distinctly different structures10 in quenched binary Fe-Ni alloys. From 0 to 4 pct Ni the structure consisted of blocky grains of a with a low and random dislocation density. Alloys with 4 to 25 pct Ni exhibited a cell structure with a high dislocation density; and at greater than 25 pct Ni the structure consisted of internally twinned plates. The structural change at approximately 4 pct Ni suggests that alloys with low nickel content transform by a different mechanism than those with intermediate nickel contents and the transition from the cellular to the internally twinned structures at approximately 25 pct Ni is analogous to the transition from needles to internally twinned plates that occurs over a narrow range of carbon contents in Fe-C martensites.11,12 Conventional bainitic and martensitic modes of austenite decomposition operate in ternary Fe-C-Ni alloys having less than 10 pct Ni. This investigation was conducted in order to explore the conditions under which the massive, bainitic, and martensitic transformations occur and the relationships between these modes of decomposition.

Jan 1, 1965

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By W. B. Heroy

The rapid development of transportation routes on the African continent in recent years has greatly stimulated the demand for motor fuels and this in turn has led to more extensive exploration of such limited portions of the continent as seem to give promise of commercial oil production. In 1930, however, only two countries were classed as producers of petroleum and only one, Egypt, attained any importance. Egypt The petroleum production of Egypt is derived from the Gemsah and Hurghada fields on the west coast of the Red Sea and the Abu Durba, on its eastern shore in the Sinai peninsula. The Gemsah field, which began to produce commercially in 1912, has now practically ceased production, owing to the invasion of salt water. The Hurghada field has been producing since October, 1914. It now has about 60 producing wells. During 1929, a deeper sand with flowing produition was discovered in the eastern part of the field, producing oil of lighter gravity and free from water. The Abu Durba field was discovered by the exploration work of the Egyptian Government in 1918, oil having been found at a depth of 172 ft. This field has now 15 producing wells but a very small production. The production of these Egyptian fields over the last five years, is as follows: Metric Tons Metric Tons 1926......................... 172,881 1929....................... 271,520 1927......................... 184,557 1930....................... 277,146 1928......................... 269,324 This oil was all produced by the Anglo-Egyptian Oilfields Ltd., a constituent corporation of the Royal Dutch Shell group. During the year 1930 the Egyptian Government was engaged in geophysical prospecting of reserved areas along the Red Sea coast. Other Countries Soma1iland.—A geological survey of Somaliland was undertaken by the Somaliland Petroleum Co., Ltd., a subsidiary of the Royal Dutch

Jan 1, 1931

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

J. L. JONES,* Pittsburgh, Pa.-If a nickel anode is cast under commer-cial conditions, will it contain nickel oxide? Will the nickel oxide affect the rate of corrosion in a double sulfate solution; or will the nickel oxide dissolve in a double sulfate solution? I would also like to ask whether a 98 per cent. pure nickel anode will corrode as fast as a 96 per cent. nickel anode; whether electrolytic nickel will corrode less rapidly than nickel containing a small amount of carbon; and whether the materials some-times used in coating molds for casting nickel anodes will affect the rate of corrosion of the anode? In other words, whether an electrically non conducting coating is likely to be present that will prevent the nickel anode from corroding rapidly. JOHN F. THOMPSON.-The nickel oxide will not dissolve in the double sulfate solution, as far as we know. We do not make the ordinary nickel anode of commerce, but we supply nickel to the nickel anode makers. Those makers almost invariably buy a high-carbon nickel shot, ranging around 0.45 per cent. carbon. In their process, they even further, car-burize it so as to get nickel that will melt easily and be fluid enough to fill the mold, so that the ordinary cast anode on the market is unquestion-ably oxide free. The only time that such an anode will have oxide will be through an error in melting. Some cupola makers of anodes have had trouble with oxidation, but as a rule the anodes are thoroughly carburized; so much so that they probably carry a couple of per cent. of carbon of which around. 1.6 per cent. is graphite.

Jan 12, 1919

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20'24'25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M'1B|28'i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown' that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By Orson Cutler Shepard

RECENT research work in the flotation concentration of minerals has been concerned mainly with flotation reagents and the mechanism by which collecting reagents are held to the surface of certain mineral particles. The fundamental question of why air bubbles cling to properly prepared mineral surfaces is usually dismissed with the statement that the surface is air-avid or water-repellent. In my article in MINING AND METALLURGY for June, 1932, I showed theoretically that surface tension relationships govern bubble attachment in Rotation. This explanation has not been accepted by many; probably be¬cause the difficulty of measuring solid-solution surface tensions prevented obtaining experimental evidence. If the surface tensions involved in the system [solution, mineral, air bubble] are responsible for attachment of the air bubble to the mineral, any change in the surface tensions should cause a corresponding change in the attachment of the air bubble. An example in which the mineral-solution surface tension could be varied was found with mercury. When mercury is in contact with solutions of certain electrolytes the surface tension at the contact of mercury and solution can be altered by electrical polarization of the mercury. The surface tension rises to a maximum as the mercury is given an increasing negative potential and then decreases with further increase in potential. The theoretical relation between the surface tensions and the attachment of an air bubble is given by the following equation:

Jan 1, 1936

Soil Testing for Engineers. By T. W. Lambe. Published by John Wiley & Sons. 165 P. $5.00.-Filling a need for a text for the teaching of soil testing in the laboratory, this book is also of value as a reference for practicing engineers and for personnel in soil laboratories. Following an introductory chapter on general laboratory procedures are chapters devoted to the individual laboratory soil tests which are commonly employed. Apparatus, supplies, recommended procedures, discussion of procedure, calculations results, and numerical examples are provided for each test. Brief derivations of formulas and explanations and discussions of calibration procedures and special techniques are given in the appendix. Mesabi Pioneer. Copyrighted 1951 by the Minnesota Historical Society.- Publication of this book has been made possible by a generous gift to Society from the E. J. Longyear Co. of Minneapolis. This book covers the evolution of the Mesabi Range from a wilderness into the nation's greatest iron producing area. In this book is found the first hand experiences of Edmund J. Longyear who saw the development of the range from its beginnings, and who himself took a notable part in it. In 1890 Edmund J. Longyear sank the first diamond drill hole on the Mesabi. During the next two decades he sank pits and holes- 7133 of them-throughout the length and breadth of the Mesabi Range, exploring for iron ore. He saw roads and railroads built. He watched the range communities--Hibbing, Chisholm, Biwabik, Mountain Iron and the others change from exploration camps to

Jan 11, 1951

By H. J. Rose

In a paper1 presented before this Institute in 1926,I briefly discussed the evaluation of coking coals by means of ultimate analysis. The paper contained several graphic studies in which coal analyses calculated free of moisture, ash, sulfur and nitrogen were plotted on triaxial diagrams in which carbon + hydrogen + oxygen = 100 per cent. From a study of such data for 600 coking coals of the United States, and 150 coking coals of Wales, France and Germany, it was concluded that it was usually possible to predict coking properties and by-product yields with fair success from ultimate analysis. The coals which have proved exceptions to the general rules were found to have physical peculiarities. Run-of-mine Coal It must not be forgotten that run-of-mine coal is a composite material consisting of many constituents differing in physical properties and chemical analysis. A coal sample usually contains: 1. Glossy black coal known as anthraxylon or vitrain. This constituent usually has the strongest coking properties, and the lowest ash content. 2. Dull black coal consisting of attritus containing thin layers of anthraxylon. It is also known as clarain. This constituent, in a coking coal, usually has good to excellent coking properties. 3. Mineral charcoal or fusain. This is a porous black material which is soft and crumbly (unless impregnated with mineral matter) and which has absolutely no coking properties. It is different in every respect from the other constituents in coal. The volatile matter content of mineral charcoal is less than 20 per cent. even when it is associated with high-volatile coals. As would be expected the hydrogen content is low, and the carbon content is high. 4. A coal sample may contain tough gray canneloid material which has a high-volatile matter and a high hydrogen content, but is poor in coking qualities.

Jan 1, 1930

By John Porter

THE requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet process and the dry.

Jan 1, 1925

Single orders 2.5 c. Pamphlets 10. c. each in lots of three or more. Pamphlets 5 c. each in lots of fifty or more. These prices prevail for orders for pamphlet, of the same or different titles. The pamphlets listed on the following sheets are advance copies printed to facilitate discussion at the meetings of the Institute. They are offered for sale at the reduced prices given above as long as the supply, lasts. This list is published in the Bulletin in order that members may have the first opportunity to secure pamphlets, which sometimes are in such great demand that the supply is exhausted before the wants of members can be supplied. The following list includes only a fraction of the pamphlets that have been published by the Institute. Any other paper published by the Institute may be obtained for the price of $1, except those published in Volume XXXI, which are rare.

Jan 5, 1917

The Committee appointed by your Board of Directors to nominate Officers for the Institute for the year 1915 invites the participation of all members in the nominations. The suggestion of names for the various offices will be appreciated and given full consideration when making the selection of candidates which this Committee will recommend. The officers to be elected at the annual meeting in February, 1915, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows:

Jan 6, 1914

By John W. Cloud

IN 1877 the Pennsylvania Railroad Company removed an old bridge from its line at Duncannon, Pa., built intermediate piers and erected shorter spans of the Pratt truss type, which had previously been in use on another portion of the road. The design of this truss would not admit of diagonals larger than 1 5/8 inches diameter, and in order to stiffen the bridge somewhat steel rods were introduced for the main diagonals in the first and second panels, 1 5/8 inches and 1 3/8 inches diameter respectively. These rods were threaded without upsetting, and by the ordinary formulae the strains were of the same intensity upon both, viz., 16,000 pounds per square inch with the maximum loading. The other main diagonals in the truss are 1 5/8 inches diameter, and of iron. It was specified for the steel rods : Elastic limit, - 45,000 lbs. Tensile strength, - 80,000 lbs. Elongation, - 20 per cent. The steel was procured without difficulty, and it allowed a factor of safety of 2 3/4 at elastic limit, while a similar factor of 2 1/2 had for a long time been successfully used for iron. In the course of three years, from time to time, six of these steel rods broke, three of them being 1 3/8 inches in diameter, and three 1 5/8 inches in. diameter. The broken rods were tested, and three of them. analyzed at Altoona to ascertain the cause of failure, and what modi¬fications should be made in the steel for such service. Examination showed that all the rods were broken in detail close under the nut. The threads were well cut and properly rounded at the root. In testing the rods micrometer screws,. reading to .0001" with electric bell to signal the contact, were attached to the test pieces, and by this means the modulus of elasticity and elastic limit accurately obtained.

Jan 1, 1881

Volumes 57 and 58 of the Transactions were mailed together during the third week of August to all members whose dues for 1918 had been paid on Aug. 1. Any member whose copies fail to reach him within a reasonable time is requested to notify the Secretary. Volume 59 is on the press, and will be ready for distribution early in October.

Jan 9, 1918

Notice is hereby given that all members whose dues are paid for the year 1917 will be supplied with a copy of the Volumes MV and LV. Volume LVI has been delayed by the fact that our printer, like almost every other industrial society, has taken up war work and is under great pressure in addition thereto. Volume LVI will be sent before the end of the year, to members whose dues for the year 1917 are paid.

Jan 12, 1917

Mr. Address Member ,is hereby proposed by the undersigned; as a Associate Junior Member of the American Institute of Mining Engineers. Signatures of three Members or Associates. Place of birth Year of birth Education, when, where and how acquired, with degrees, if any. A technical education is not requisite for membership. Dates Please give record of experience on following page with dates; for example, in the form used by "Who's Who In America" and similar publications.

Jan 5, 1917

By E. H. Greener, M. E. Fine

The internal friction (1/Q) of cobalt Fig. 1 (measured by an electrostatic dynamic method1) near 250°C begins to increase rapidly on heating and continues to increase until 560°C, the highest tem- perature measured. In the plot of log of 1/Q against 1/T, above 250°C the data nearly fit two straight lines intersecting at 400°C, approximately the temperature of the hexagonal-cubic transformation. The higher temperature branch corresponds to an effective activation energy of 6500 cal per mole, the lower temperature branch 11,000 cal per mole. Young's modulus Fig. 2 increases approximately

Jan 1, 1959