Search Documents

By J. G. Kura, P. D. Frost, L. W. Eastwood

THE preparation and general properties of mag-nesium-lithium base alloys have been described in earlier papers.l,2 Lithium forms solid solutions with pure magnesium, lowers its density, and improves its formability. The improved isotropy and better formability of these alloys are attributed to the ability of lithium to convert the magnesium lattice from hexagonal (alpha phase) to body-centered-cubic (beta phase) structure. This change in structure is, however, accompanied by some limitations which make it difficult, if not impossible, to combine all the desirable properties in one composition. The most important of these limitations is the tendency of the high-strength alloys to overage and lose strength at temperatures of the order of 150" to 200°F. A study was made of the effects of composition and heat treatment on the age-hardening character- istics of the alloys. Stability of properties was determined by hardness and tensile testing of the alloys at room temperature after various periods of exposure to elevated temperatures. Precipitation-hardening curves are shown for a number of magnesium-lithium-zinc alloys in fig. 1. All the alloys were solution treated at 700°F and aged at 200°F. The reason for using the drastic quench, toluene at —105°F, was to reduce the rapid precipitation of the hardening phase which takes place at room temperature. Previous experience has shown that a hardness of about 90 to 95 Rockwell E is indicative of yield strengths in the range of 35,000 to 40,000 psi. This is a desirable strength level for magnesium-lithium base alloys with specific gravities of the order of 1.65 or less. Although the hardness level is raised by large zinc contents, a corresponding decrease in the cold formability of these alloys occurs with increasing zinc content. Thus, alloys containing up to about 10 pct Zn and having hardnesses of the order of 70 to 75 Rockwell E may be bent over a very small radius; however, the 16 pct Zn alloy requires a bend radius of more than 8T. The hardness relationships illustrated in fig. 1 can be explained by the partial phase diagram shown in fig. 2. The zinc-free magnesium-lithium alloys are entirely body-centered cubic (100 pct beta phase) when the lithium content of the binary is 10.3 pct or higher. When zinc is added, the boundary between the beta and alpha-plus-beta fields at 700°F is shifted to lower lithium contents. In addition, the solubility of zinc at 700°F decreases with decreasing lithium content. It is shown by a study of micro-structures that the limit of solid solubility of zinc in the 6Mg/Li* matrix at 700°F is about 19 pct. It is believed from a study of the aging curves that this limit is about 2 to 3 pct at 200°F. Zinc additions up to about 2 pct increase the hardness and strength of the magnesium-lithium base solid solution. Larger additions of zinc effect further hardness increases, but precipitate during prolonged aging at 200°F. Alloys having 14 to 20 pct Zn precipitation harden extremely rapidly during quenching, even when quenched in toluene at —105° F. The high-zinc alloys overage at 200°F but are capable of maintaining reasonably high hardnesses for periods up to 1000 hr.

Jan 1, 1951

By N. M. Levine, W. M. Fassell

In this laboratory study the problem of aerative conditioning to separate chalcopyrite and pyrite from cobaltite was simply effected with a sulfy-drate collector and pH by proper choice of mixing variables. It was shown that for a given impeller type and geometry, selectivity is governed by a relation between the Froude number and a modified power number multiplied by impeller tank-diameter ratio wherein the power factor is expressed as power intensity or horsepower per unit volume of contained pulp. In applying this approach to other systems, other criteria would be used in place of selectivity. The purpose of this paper is to show how solutions to problems of aerative conditioning of pulps may be enhanced by development of mixing parameters in a given system through application of a fundamental approach to agitation. The term aerative conditioning refers to a combination of processes which include mechanical gas dispersion, gas solution in the liquid phase, transport of dissolved gases and other reactants to the reaction zone, physico-chemico interaction within the liquid phase and/or at the solid surface, and, finally transport of products away from the reaction zone. Important elements of these processes are: 1) Air-Liquid Contact Area: This area limits the rate at which a given gas may dissolve in a given liquid. Thus, an aerative conditioning system should be designed for optimum gas dispersion. 2) Diffusional Factors: Such factors as concentration gradient, diffusion film thickness, and diffusivity may govern the rate at which dissolved constituents are transferred to the zone of interaction at a particle surface and the rate at which reaction products are transported therefrom. Thus, such systems would be designed for maximum turbulence to effect good mixing and to minimize diffusion film thickness. 3) Solids-Turbulent Liquid Contact Time: Sufficient time should be provided for interactions to take place at solid-liquid interfaces. The region of maximum turbulence for mechanical systems being in the impeller zone, it is important that the number of passes through this zone be optimized. This means that a proper balance should be struck be- tween flow and turbulent power to achieve optimum conditioning time. Too high a flow rate and insufficient turbulence may be improper if the reactions are diffusion limited. On the other hand, too much turbulent power and too little time in the reaction zone due to insufficient flow power may also be limiting. 4) Geometry and Impeller Design: The design of the conditioning vessel and the type of impeller employed are important factors in determining the relative distribution between flow and turbulent power and the degree of gas dispersion. Maximization of power input would be to no avail if the distribution between flow and turbulent power were improper or gas dispersion insufficient. 5. Physical Chemistry: The reactions between dissolved gases and solid surfaces may be limiting if gas solubility, activation energies and/or free energies are not favorable. J. H. Rushton, E. W. Costich, and H. J. Everett' have summarized the mechanical elements of the combination of processes listed in a fundamental mixing equation. This equation was derived by dimensional analysis and relates the physical variables for a single impeller, centered in a cylindrical, vertical axis, flat-bottomed tank. It is, where T is tank diameter in feet; H is liquid depth in feet; C is height of impeller off tank bottom in feet; S is pitch of impeller; L is length of impeller blades; W is width of impeller blades; R is number of baffles; D is impeller diameter in feet; Np is the power number, pg/dN3D5; P is power in foot-pounds per second; g is the gravitational constant, feet per second; J is width of baffles; B is number of im-

Jan 1, 1961

By A. O. P. Casbarian

An analytical method is developed to determine the variation of the ultimate lateral resistance of a plate in a cohesionless soil with depth. This analysis is based on a modification of Rankine's classical earth pressure theory and the theory of plasticity as applied to soils. The ultimate resistance is defined as the product of the effective stress at the midpoint of the plate, the area of the plate and a dimensionless variable termed the ultimate resistance factor. This variable has been plotted us the depth ratio: i.e., the ratio of of the depth of embedment us the height of the plate. The resistance of a plate may then be calculated using the values af the ultimate resistance factor from the chart provided or the equation may be programmed for use in an analysis of anchor systems in cohesionless soils. It is emphasized that the analysis is semitheoretical. The theory has been compared with experimental results reported in the literature and results indicate general agreement. Actual field tests are necessary to further verify this theory. INTRODUCTION With the exploration for oil offshore in waters all over the world, it is of importance to determine the behavior of the various soils in relation to their ultimate resistance to deformation. Examples of such problems are the holding capacity of anchors and the lateral resistance of piles. Very little information is available in the published literature on the design and performance of anchors, in either cohesive or cohesionless soils. The analysis developed in this report is the first step in obtaining a solution for the determination of anchor holding capacity in a cohesionless material. DISCUSSION The theory used in the analysis is based on the ultimate strength of the soil and is the maximum resistance developed by the plate against further movement. In such a state the elastic deformations are disregarded in comparison with the plastic deformations. Hence, the plate can be considered as completely rigid. The theory of plasticity determines the three unknown stresses at any point by means of two equilibrium conditions for a small earth element in combination with the failure condition. However, the exact solutions can only be carried out in a few simple cases such as, for example, when the rupture or failure lines are straight (Rankine theory) or with spiral and straight rupture lines (Prandtl theory).l Kiitter 2 derived a single equation expressing the variation of the stress in any given rupture line. To utilize this equation, it is necessary to know the stress in the rupture line at a certain point. Unfortunately, this is difficult to obtain unless the rupture line intersects the free surface at a certain angle or when the earth is cohesion-less and unloaded. A method to overcome this is to consider only the boundary conditions at both ends of a rupture line without investigating the equilibrium of the earth above the rupture line. This assumes that the rupture lines meet the surface at statically correct angles, so that boundary stresses may be determined. As Kiitter's equation furnished a relation between these stresses, the unit earth pressure may be calculated at the point where the rupture line meets the wall. Another way in which Kotter's equation may be applied is in investigating the equilibrium of a soil mass above a rupture line. This method assumes that the failure or rupture line is known and that the boundary stresses in the rupture line at the ground surface can be determined. In this case it is possible to determine the earth pressure from the equations of equilibrium.

Jan 1, 1967

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-A1 alloys has been measured up to the solubility limit for formation of aluminum nitride using the Sieverts method. The activity coefficient of nitrogen decreases slightly with increasing aluminum content in the range of 0 to 4 wt pct Al. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from fhe elements dissolved in liquid iron has been determined to be: ?F" = -59,250 + 25.55 T in the range from 1600º to 1750ºC. The solubility of nitrogen in liquid iron alloys and the interaction of nitrogen with dissolved alloying elements in liquid iron have been the subject of a number of research investigations.' Most of this work, however, has been reported for concentrations well below those necessary for the formation of the alloy nitride phase. Data in the concentration region near the solubility limit of the alloy nitride, particularly for systems exhibiting stable nitrides, are important in evaluating the denitrifying power of various alloying elements. They are also useful in determining the stability of a given nitride if it is to be used as a refractory to contain liquid iron alloys. In view of the importance of aluminum as a deoxidizing agent in commercial steelmaking and the fact that its nitride, AIN, is a highly stable compound and has merited some consideration as an industrial refractory, the following investigation was undertaken. The use of the Sieverts technique provided a measurement of the equilibrium nitrogen solubility in liquid Fe-A1 alloys as a function of nitrogen gas pressure up to 3.85 wt pct A1 in the temperature range of 1600º to 1750°C. The values obtained by the Sieverts method were checked by means of a quenching method in which liquid iron was equilibrated with an A1N crucible under a known partial pressure of nitrogen gas, and the solubility of A1N in liquid iron determined by chemical analysis. EXPERIMENTAL PROCEDURE The theoretical considerations involved in determining the solubility product of a solid alloy nitride phase in liquid iron by measuring the point of departure of the nitrogen gas solubility from Sieverts law have been discussed by Rao and par lee.' The principal problem is to determine the variation of nitrogen solubility in an alloy as a function of the pressure of nitrogen gas over it with sufficient precision to establish the break point in the curve at the solubility limit of the alloy nitride phase. A fairly large number of data points are required to do this. A second problem is the determination of the composition of the precipitated solid nitride phase. This is necessary in order to define completely the thermodynamic relationships. The Sieverts apparatus used to make the nitrogen solubility measurements in this investigation is of essentially the same design as that described by Pehlke and E1liott.l The charge materials were Ferrovac-E high purity iron supplied by Crucible Steel Co. and 99.99+ pct pure aluminum. Recrystal-lized alumina crucibles were used, and were not attacked by the liquid alloys. The hot volume of the system which was measured for each melt ranged from 46 to 50 standard cu cm and was found to decrease linearly with decreasing pressure and with increasing temperature. The temperature coefficient of the hot volume at 1 atm pressure of argon gas was essentially constant for all experiments at a value of -6 X 10-3 cu cm per "C. The melt temperature was measured with a Leeds and Northrup disappearing filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature scale was calibrated against the observed melting point of pure iron taken as 1536°C. The emissivity of all melts was assumed to be that of pure iron, taken as 0.43. The charge weights ranged from 110 to 140 g and the range of aluminum contents covered was from 0 to 3.85 wt pct. Aluminum additions were made as 12 to 15 wt pct A1-Fe master alloys previously prepared in the system under purified argon. The compositions of the master alloys were checked by chemical analysis and found to be in agreement with the charge analyses. Vertical cross sections of the master-alloy ingots were used as charge material for the equilibrations in order to minimize the effect of any segregation which might have occurred during solidification of the master alloys. Determinations of the solubility product of

Jan 1, 1964

Prof. Henry M. Howe, New York, N. Y. (communication to the Secretary*):—The results presented in Mr. Mathewson's paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min. from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the removal of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis.

Jan 1, 1908

By R. L. Ash, R. R. Rollins, C. J. Konya

An investigation was performed to determine conditions for optimizing the spacing of simultaneously initiated multiple explosive columns. This was done by using models of mortar, dolomite, and Plexiglas with 10-grain mild detonating fuse as the explosive charge. It was desired to simulate blastholes with multiple primers initiated by detonating fuse or when high-velocity explosives are used in low-velocity materials. It was found that optimum spacing between multiple charges was strongly influenced by charge length. At less than optimum charge length, the spacing at which complete shearing was possible between adjacent charges decreased exponentially with a subsequent loss of broken material volume. For charges fired simultaneously, larger burdens and spacings were possible as compared to those necessary for single-crater charges. For each material studied, there was a characteristic optimum charge length and a maximum attainable spacing at any given burden. Proper selection of the spacing distance between charges is fundamental to successful blasting. Its value directly affects the cost of drilling and explosives used per unit of broken material. In addition, the choice of a spacing that is Compatible with a given set of blasting conditions aids in the control of fragmentation sizing, ground vibrations, overbreak, and throw which in turn, influence other production costs. For example, normally loaded blastholes that are spaced too closely invariably promote overbreak and usually give coarse fragmentation. Unless care is taken, airblast and violent flyrock will occur and under certain conditions cutoffs and misfires may result. Too large a spacing, on the other hand, frequently leads to conditions that form bootlegs or toes. The choice of a particular spacicg to use, however, is largely a matter of individual experience and judgment, usually based on trial and error. Very little is known or can be found in the literature with regard to how the spacing between charges is related to field conditions and charge geometry. As a general rule, the firing time sequence of adjacent charges and properties of a material are thought to have the most significant influence on the spacing distance best suited for any given field condition. For example, delayed initiation of adjacent charges usually always requires a closer spacing than when charges are fired at the same time. This should be expected if one considers that the energy normally dissipated and lost in the surrounding ground from charges fired independently would be captured and utilized for breaking material between charges when they are initiated together. Spacing can be extended also when charges are aligned with structural planes of a material, such as jointing, along which shearing is relatively easy. It is customary to relate the spacing (S) between charges to their common burden (B) in the form of a spacing ratio, or SIB. The burden normally is considered as the optimum depth or distance from any single charge perpendicular to the nearest free or open face at which the desired fragmentation and maximum crater yield are obtained. For production blasting, value of the ratio is generally considered to vary from 1 to 2, depending on conditions.1-6 When adjacent charges are fired independent of one another, the value varies from 1 to about 1.4, the closer amount being employed to square corners or produce craters having the ideal 90" apex angle. The larger ratio is the geometric balance value for craters having an apex angle of 135". The basic ideal crater forms in the plane of the charge diameter for charges fired independently are shown in Fig. 1. In the event charges are fired simultaneously, geometric balance in the plane of their charge diameters suggests that a spacing ratio near 2 would be appropriate, as illustrated by Fig. 2. In practice, however, some compromise ratio value must be selected to conform with the specific ground conditions. An example would be where the jointing planes tend to produce 60° or 120° crater angles, the appropriate geometrically balanced charge arrangement being given by Fig. 3. In this condition, the spacing ratio is 1.15, not 1 or 1.4 as suggested for the 90° cratering of independently fired adjacent charges. In view of the foregoing, it would seem logical to assume that whenever charges all having the same burden are fired at the same time, spacing distances always can be greater than those permitted by charges fired independently. In practice this is not the case, however.

Jan 1, 1970

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey' have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel'perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,' and Fletcher and Wilson' have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By Hobart M. Kraner, E. B. Snyder

THIS paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, particularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercial blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. FACTORS AFFECTING CHOICE OF REFRACTORIES If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing temperature, which he in turn interprets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and resistance to the action of slag. In most refractory applications several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient stages and the progress is determined by measuring slight changes in. porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures . at which they are to be used, although in many cases it would be desirable from the user&apos;s point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. -Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By Carville E. Sparks, Rollin Farmin

TRIAL installations of rock bolts, of the slit-rod-and-wedge type, were under way at several units of Day Mines, Inc., when Korean hostilities interrupted the already slow deliveries of steel bars to the Coeur d&apos;Alene district. Factory-made bolts had not yet been put on the local market, so the program was halted for lack of supplies. Interest was revived by a visitor&apos;s description of wooden roof bolts. These were said to have been used briefly with apparent success in a coal mine, until apprehension voiced by the U. S. Bureau of Mines caused the practice to be suspended. To make wooden bolts for trial in ground support, Day Mines acquired a second-hand doweling machine equipped with two cutting heads, one to turn out the desired round rods of 2-in. diam, the other to turn out 1-in. rods to be used as powder-tamping sticks. This machine was installed in the all-weather sawmill of the Hercules mine unit at Burke, Idaho, where fabrication of the wooden bolts commenced early in 1951. Most of the mining in the Coeur d&apos;Alene district is along steeply dipping veins in shaly quartzite and argillite of Algonkian age. Ground support commonly is required in zones where the rocks have been sheared, brecciated, and hydrothermally altered. Pressure from the sidewalls is more troublesome than weight overhead, but both increase with the size of the mine opening. Caving may come from a progressive sloughing of irregular rock fragments or from an exfoliation and buckling of the layered wall rocks. The disintegration is thought to develop from an initial elastic expansion of the rock toward the newly-created mine opening, followed by the dilation of many tiny partings in the rock by absorption of water. As the partings widen, masses of rock develop weight and become free to fall. The function of rock bolts is to prevent or retard widening of partings in the rock supported. Wooden Bolts, Wedges and Headboards Bolt assembly used by Day Mines consists of a bolt 4 or 6 ft long, two wedges 16 in. long, and a headboard 30 in. long, Fig. 1. All four pieces are made of local red (Douglas) fir, either green or well-soaked in the mill pond before it enters the sawmill. Bolts are fabricated from cants, 2 1/4 in. sq, cut from relatively straight-grained timber with a minimum of knots and trimmed to 4- and 6-ft lengths. The bolt then is turned in the doweling machine from 21/4 in. sq to 2 in. diam round, except for a 4-in. length at one end which is left full square to provide the striking head and the shoulder that holds the headboard in position for wedging. The foot end of the bolt is slit with a thin saw for a length of about 16 in., thereby making a slot to receive the wedge against which the bolt is driven for anchorage at the bottom of the rock hole. A similar slit, 12 in. long, is made in the opposite (head) end of the bolt to receive the second wedge, which crowds the headboard against the ground at the collar of the rock hole and puts the bolt in tension. The second slot is aligned 90" from the plane of the first slot to avoid Longitudinal splitting and is notched out slightly to allow easier insertion of the collar wedge after the bolt has been driven to bottom. To prevent splitting the headboard by spreading action of the head wedge, this slot is oriented at 90" to the grain of the headboard when the pieces are assembled, Fig. 2. The wedges are similar to standard mine wedges, but more slender; they are cut 1 7/8 in. wide and 1 in. thick at the heel and taper out in 16 in. of length. The headboard, or bearing plate, is not necessary for some types of ground but generally is desirable because it helps the bolt to support an area of loose, friable rock and reduces the tendency for the rock at the collar of the hole to split away from the wedged head by distributing the pressure over a wider rock surface. The headboard may be a 24-to 30-in. length of 3-in. plank, 8 to 12 in. wide, but a similar length of rounded sawmill slab serves equally well at 20 pct of the cost. A hole of 2-in. diam is bored or punched through the center of the headboard, either at 90" or at various high angles to its surface. The bolt is inserted to its shoulder through this hole, then driven into the rock hole. Bolts, wedges, and headboards are given a full timber preservative treatment to inhibit rot. Bundles of each are immersed in a warm saturated solution of Osmose salts in water for 48 hr, removed, dripped dry, and stored in a relatively humid underground depot to cure. Most wooden rock bolts used by Day Mines are 4 ft long. Holes to receive them, about 42 in deep and 2 1/8 in. in diam, are drilled into the rock&apos; to be supported, nearly normal to the periphery of the mine opening. The type of drill used is dictated by convenience: stoper, jackleg, or jumbo-mounted drifter. Correct depth of the hole is assured by use of a measuring stick that has been cut to the proper distance from drill chuck to the ground at the collar of the hole when a standard length drill rod is at the bottom. The bolt is seated to the shoulder through the hole in the headboard, the foot-end wedge is placed in its slot, and the assembly is inserted into the rock hole. Then the bolt is driven until it is seated solidly on the wedge against the bottom of the rock hole. Driving may be by hand with a sledge, or

Jan 1, 1954

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?&apos;, phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?&apos; layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By Howard R. Keil

Prior to World War 11, approximately 500 tons per day, or one-third of the ore being shipped to the Golden Cycle Mill at Colorado Springs, Colo., from the Cripple Creek district, was being treated in the flotation plant. The remaining 1000 tons, along with the flotation concentrates, received the usual roasting and cyanide treatment. Since it was not possible to make a disposable tailing on the general run of Cripple Creek ores by flotation alone, it was necessary to treat the flotation tailings by cyanidation, along with the roasted ore. By this treatment, an overall economical tailing could be made. The gold ores from the cripple creek district are the highly siliceous sulphotel-lurides with approximately 3 pet total sulphides. In the lower grade ores most of the values are found in very finely disseminated pyrite. In some of the higher grade ores the tellurides, calaverite and sylvanite, can be recognized. After several years of floating cripple Creek gold ores, having a very low mineral content, it was concluded that this type of ore required a type of flotation machine that would give a rather violent aeration and agitation. This action produced a fairly deep froth column which contained not only the free mineral, principally pyrite, but also most of the middling product; this was most essential in producing a low grade tailing by flotation alone that could be discarded to waste. After investigating most of the current types of flotation machines, it was decided to convert to the Fagergren type. During World War 11, the flotation plant was modified to handle lead and zinc ores. The treatment of these ores was carried on until April 1946. At this time the flotation plant was again reconverted to handle the Cripple Creek ores. Selecting Ores for Flotation During the period of reconversion a considerable amount of experimental work was carried on in the laboratory to determine if a disposable tailing could be made by flotation alone, on certain selected Ores from the Cripple Creek district. It was found that most of the dump Ores and a few of the low grade mine ores could be treated by this method with very satisfactory results. After the preliminary test work in the laboratory, it was decided to carry on further work On a plant-size scale to see if similar results could be obtained. On April 15, 1946, a part of the plant was put into operation as a pilot plant. The various ores that had been found suitable for treatment by this method in the laboratory, were run through the pilot plant at the rate of 200 tons per day for a period of several months. Results were so encouraging that it was decided to put the plant in full-scale operation. Since that time plant capacity has been the from 500 to 1000 tons per day. This has been done not by the installation of more machinery but by (I) crush-

Jan 1, 1949

By AIME

HAPPILY, a large group of the non-ferrous fraternity have long valued a personal association with the new Chairman of the Institute of Metals Division. Many others who will meet him, either officially or unofficially this year, will find themselves sharing the enthusiasm with which he has been welcomed to his new office. Albert A. Smith, Jr., was born at Butler, N. J., on Dec. 28, 1904, and moved to New Haven in time to initiate his preparation for Yale University on the home grounds. After receiving a B.S. degree cum laude in 1926, he stayed on for graduate work at the Hammond Laboratory under C. H. Mathewson, and was awarded an M.S. degree in 1928.

Jan 1, 1948

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a very general loosely used term that includes virtually all finely divided types of limestone as well as burned forms of lime. However, actually (and according to Webster) lime is only calcined limestone (known as quicklime, calcium oxide, or calcia). It also embraces the secondary product of quicklime-namely hydrated lime or slaked lime (calcium hydroxide). Fundamentally there are two basic types of limestone-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts in terminology. The only difference is that the dolomitic types are a combination of the elements, calcium and magnesium, whereas high calcium limes contain only 0.5 to 2 pct of magnesium. Both types, which are made through calcination at high temperatures, are shown chemically as follows: [ ] In the above reactions either type of limestone is burned (calcined) in furnaces known as lime kilns so that the carbon dioxide content of the stone is expelled as a gas. With high calcium limestone 44 pct of the weight of the stone is lost; with dolomitic limestone the loss is 48 pct. Also, both reactions are chemically reversible since quicklime absorbs carbon dioxide readily and in so doing transforms itself back to the original carbonate form. Most quicklimes correspond in size to the original rock, which varies from one to eight inches, depending upon the type of kiln employed. Slight shrinkage occurs during calcination. A few limestones when calcined will decrepitate (break down) into a fine powdery form; however, chemically it is the same as the pebble or lump-sized material. For some uses the lumps of quicklime are pulverized and packaged. Since quicklime has great affinity for moisture and carbon dioxide, it is perishable. When it absorbs moisture and CO2 slowly from the atmosphere, the resulting product is "airslaked." Consequently, it must be stored in dry, moisture-proof areas that are free from CO2. Because of its fugitive nature, it is usually consumed within a few weeks after manufacture. A more stable form of lime is hydrated lime-commercially made by adding water to the quicklime until the lumps break down into a fine, white powder. This product, which is usually packaged, can be stored more safely; and many of its uses are interchangeable with quicklime. The irreversible chemical reactions of hydrated lime for both high calcium and dolomitic types are: [ ]

Jan 1, 1960

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

The Mining Journal Annual Review. The Mining Journal, London. $1.00, 200 pp., 1952.-Contains 70 specially contributed articles reporting on events in the metalliferous mining industry throughout the world during 1951. The articles are written from the standpoints of: Economics, world mining fields, progress reports on Empire mining companies, and British mining taxation. The review has appeared for a period of 20 years. Technical developments in mining, ore treatment, refining, and metallurgy are covered. Dun & Bradstreet Reference Book. Dun & Bradstreet Inc. 4000 pp., 1952. -Changes, brought about by the expanding economy, have been made for the three million listings for the United States and Canada. Planning for the changes started more than 10 years ago. New listings have been included for the metals and mining industries on all levels. The rapid development and specialization of industry have made the old symbols used in previous editions outmoded and a new system is substituted. Atlas of World Mineral Resources, . Edited by William Van Royen and Dr. Oliver Bowles. Prentice-Hall Inc. $10.75, 180 pp., 1952.-Scheduled for publication this fall, the book contains information that has never been published in map form before, as well as much that has not been presented in map form for many years. Facts on 29 minerals most important in world trade are dealt with, along with interpretation of all data available on each mineral, discussion of the world&apos;s mineral economy from viewpoint of specific minerals related to mineral exploration, geographical distribution of world&apos;s consumption, and appraisal of the adequacy of world&apos;s mineral resources.

Jan 1, 1952

By L. T. Lloyd, H. H. Chiswik

The operative deformation elements in a-uranium single crystals under compression at room temperature have been determined as a function of the compression directions. The deformation mechanisms noted may be arranged with respect to their frequency of occurrence and ease of operation in the following order: 1 — (010)-[I001 slip, 2—{130} twinning, 3—{~172} twinning, and 4bunder special conditions of stress application, kinking, cross-slip, {.-176) twinning, and (011) slip. The composition planes of the (172) and (176) systems were found to be irrational. Cross-slip was shown to be associated with the major (010) slip system, coupled with localized interaction of slip on the (001) planes. The mechanism of kinking was found to be similar to that observed in other metals in that it occurred chiefly when the compression direction was, nearly parallel to the principal slip direction [loo] and was associated with a lattice rotation about an axis contained in the slip plane and normal to the slip direction: the [001] in the uranium lattice. The resolved critical shear stress for slip on the (010)-[100] system was found to be 0.34 kg per mm2 In a single test it was shown that under compression in suitable directions twinning on the (130) also occurs at 600°C. DEFORMATION mechanisms of large grained polycrystalline orthorhombic a-uranium have been studied by Cahn.1 A major slip system identified as the (010) with a probable [loo] slip direction and a minor slip system on the (110) planes were reported; the slip direction of the minor system was not determined. The twinning systems that were identified experimentally included the (130) and the irrational (172) composition planes; observations of other traces which were not as frequent and which did not lend themselves to positive experimental identification led Cahn to postulate on the basis of indirect evidence that twinning also occurred on (112) and (121) planes. In addition to the foregoing slip and twinning mechanisms, Cahn also observed kinking and cross-slip in conjunction with the major (010) system; the cooperative cross-slip plane was not identified. The availability of single crystals to the present authors has enabled them to check these results, particularly with reference to the doubtful mechanisms and the preference of operation of any one mechanism in relation to the direction of stress application. The tests were confined to compression only, primarily because of experimental limitations imposed by the size and shape of the available crystals. The tests were performed at room temperature except for one crystal compressed at 600°C. The compression directions were chosen to obtain a representative coverage of one quadrant of the stereo-graphic projection. To test the existence of some of the deformation elements that were reported by Cahn, but were not found in the present study, several additional crystals were compressed in specifically chosen directions considered most ideal for their operation. Experimental Techniques The single crystals were obtained by the grain coarsening technique described by Fisher? They grinding and polishing on rotating laps, with final surface preparation performed in a H3PO4-HNO3 electropolishing bath. A typical crystal readied for compression is shown in Fig. 1; their dimensions were rather small and depended upon the testing direction. Crystals isolated for compression in a direction close to the [010] axis, which lay roughly parallel to the longitudinal axis of the polycrystalline rod, were about 3 to 4 mm long and 5 mm2 in cross-section, while those prepared for compression in other directions were smaller. Most of the crystals were free from twin markings and showed no evidence of Laue asterism. Several crystals, however, contained twin traces prior to compression; these were identified prior to compression so as to clearly distinguish them from those initiated during deformation. The origin of the twin markings prior to deformation may be ascribed to two sources: thermal stresses and specimen handling during isolation and preparation. Two other types of imperfections in the crystals should be mentioned: inclusions, which were probably oxides or carbides. and three of the crystals contained a small number of spherical included grains (<0.01 mm diam), which were remnants of unabsorbed grains from the coarsening treatment. The volume represented by these imperfections was small, and their presence presented no difficulties in the interpretation of the macrodeformation processes during subsequent compression. Two compression fixtures were employed: crystals A, B, C, E, and G were compressed in a hand-operated screw-driven jig whose compression platens were designed to minimize axial rotation;

Jan 1, 1956

By W. G. Lidman, H. J. Hamjian

&apos; I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:&apos; the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F&apos;) at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.&apos; Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By J. S. Rinehart, W. C. Maurer

The mechanics of impact crater formation in rock, particularly sandstone, has been sutdied, the velocity range being approximately that normally associated with oilwell gun perforators. The bullets were small steel spheres having diameters of 3/16, 9/32 and 7/16 in; impact velocities ranged from 300 to 7,000 ft/sec. The craters have two distinct parts — a cylindrical hole (or burrow) with a diameter the same as that of the impacting sphere, and a wide-angle cup comprising most of the volume of the crater. The burrow is fornred as material in front of the projectile is crushed and pushed aside, forming a cylindrical hole surrounded by a high-density zone. The clip forms as fractures are initiated in front of the projectile and propagate along logarithmic spirals, approximaling maximum shear trajectories, to the free surface of the rock. A most significant observation (made for the first time) was that, below the base of the cup in one type of sandstone, there are a group of similar fractures, not extending to the surface, which are spaced uniformly a few millimeters apart. Each fracture follows roughly the contour of the base of the cup and appears to require a certain threshold impulse to initiate it. These fractures comprise a relatively high fraction of the total, newly exposed surface area. The volume of the material removed by crushing varies as the first power of the impact velocity and the volume removed by fracturing, as the second power of the impact velocity. Penetration varies linearly with the impact velocity and is inversely proportional to the specific acoustic resistance of the target material, the proportionality constant being dependent upon the shape of the projectile. INTRODUCTION Yield of oil from a producing well is frequently enhanced by firing bullets and shaped charges through the well casing into the oil-bearing rock, forming craters and fractures from which oil can flow more readily. The purpose of this investigation has been to develop a better understanding of the mechanics of impact crater formation in rock, particularly sandstone, the velocity range being approximately that normally associated with oilwell gun perforators. FORCES OPERATIVE DURING IMPACT When a projectile moving at considerable velocity strikes a- massive target such as oil-bearing sandstone, intense and complex transient stress situations develop within both the projectile and the rock or sandstone against which it is striking. Usually the struck rock fails, the missile or projectile penetrating into the rock to some depth where it comes to rest or is forcibly ejected from its burrow by expansion of a plug of target material compressed in front of it. When the impact velocity is very high, the projectile itself may fail, breaking apart or becoming distorted; this situation is not considered here, the discussion being limited to nondeforming projectiles. Many experimental studies&apos;.&apos; have been carried out to determine the nature of the mechanics of crater formation and the salient features of the forces coming into play, some of the earliest studies being the French Army experiments performed at Metz between 1835 and 1845.&apos; The stratagem in most instances has been to make a post-mortem examination of the crater, measuring volume and depth of penetration and deducing force relationships from these observations rather than performing the more difficult (usually almost impossible) feat of measuring stresses during penetration. In many materials, the force acting during penetration of the projectile is found to be the sum of two components—(1) a constant force, independent of the velocity, representing some inherent strength of the target material; and (2) a component, proportional to the square of the velocity, representing inertial forces. For such materials, the average force per unit area acting on the projectile at any instant while it is in motion and being decelerated may be written F/A = a + bv2 . . . (1) where v is the velocity of the projectile at that instant, A is the cross-sectional area of the penetrating projectile taken normal to its trajectory, and a and b are constants which are dependent upon the target material and the shape of the projectile. It follows that the total penetration s is given by .........(2) where v, is the velocity of the projectile when it just strikes the target. Values of a and b for spherical projectiles impacting in a loose sand-gravel mixture and compacted earth were obtained in the Metz experiments. For sand-gravel, a and b are 620 psi and 0.0115 (psi) (ft/sec)&apos;, respectively; and for compacted earthworks, a and b are 432 psi and 0.0008 (psi) (ft/sec)&apos;. Figs 1 and 2

By C. D. King

THE advances in basic open-hearth practice which have occurred during the past decade, have been principally in the direction of the physical development of larger units, decreased fuel consumption and increased length of furnace campaigns. However gratifying the economies which have resulted from these improvements are, it must be granted that like advances in chemical, physical-chemical and metallurgical knowledge pertaining to open-hearth practice would have added greatly to these already attained reductions in costs and it is the purpose of this paper to stimulate the discussion and study of these phases of cooperation and their relation to ingot yields. DEFINITION AND CALCULATION OF LOSSES In discussing basic open-hearth yields, the writer refers to the ingot yields obtained in the process of converting pig iron, scrap and ore to steel. In this conversion some scrap is produced. The difference between the total weight of ingots and scrap produced and the original metallic charge, constitutes the loss. Basic open-hearth yields vary considerably, and while some of the divergencies can be explained metal-lurgically because of differences in slag analysis, proportion of pig charges, and character of steel made, there often remain differences that apparently do not readily disclose themselves. In reconciling yields by the usual accepted methods of calculation, one is often forced to evaluate large losses as "unaccounted for." Such a system is prone to accept these large losses as inherent to the operation and not susceptible of appraisement and correction. It is obvious that if the ingot yield, plus the scrap recovered subtracted from 100 per cent. determines the loss, a drop in yield may increase the loss or the scrap, and both contribute to a monetary loss. To be sure, one can subdivide these unaccounted for losses into various components, such as metallics in slag, free Fe in slag, spillage, etc., and thereby reduce the amount of losses considered as "unaccounted for." If empirical methods could indicate with some degree of accuracy all losses, however slight, the undetermined losses become appreciably smaller and resultant calculations will check actual

Jan 1, 1929