Search Documents

By J. E. Harris, J. A. Whiteman, A. G. Quarrell

The graphitizing reaction has been studied in a number of Fe-C-Si alloys in the temperature range 550° to 725°C. The TTT relationships exhibit "C" curve behavior except where nuclei, either foreign or graphite itself, are present before the start of the reaction. It is suggested that the rate -controlling process is diffusion of carbon through ferrite. For the reaction to proceed at the observed rate it is calculated that the matrix surrounding the particles must deform plastically; experimental evidence for this deformation is presented. It is well-established that the decomposition of austenite to pear lite occurs at a maximum rate at an intermediate temperature.l-5 This "C curve" be- havior, which has been reported in a number of other systems,5-10 is a consequence of the relatively low rate of nucleation of the pearlite at small degrees of undercooling of the austenite. The cemen-tite phase in the pearlite is, in turn, metastable with respect to graphite and if steels are held for prolonged periods at elevated temperatures decomposition of the pearlite occurs. It is difficult to predict the shape of the subcriti-cal graphitization TTT (time, temperature, transformation) diagram for, in this case, undercooling does not occur. However, the free-energy change for the reaction does decrease with increasing temperature" (Fig. 1) and it is thus anticipated that the rate of nucleation will fall as the temperature approaches that of the eutectoid. In addition, a decreasing growth rate with increasing temperature is predicted in some circumstances with pure Fe-C alloys. However, apparently similar conditions exist for first-stage graphitization in the austenite range (malleabilization) but no evidence for C curve behavior has been presented in the extensive liter-

Jan 1, 1965

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein's process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein's bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By J. A. Scott, F. R. Hensel

The paper deals with the investigation of two types of coreless induction furnaces, one of 60 cycles, the other of 5000 cycles. Nickel was used as test material and the absorption of oxygen by molten nickel was chosen for determining the influence of the frequency on the metallurgical characteristics of the furnaces. Dr. Herty's aluminum method, slightly modified, was found suitable for determining the nickel oxide content in nickel. Also an electrolytic method for determining alumina in nickel was worked out. The solubility-temperature relations for nickel oxide in molten nickel were determined approximately. It was found that the solubility of nickel oxide increases with the temperature. Comparative tests on the rate of oxygen absorption made in a 60 and a 5000-cycle furnace showed that the absorption of nickel oxide in nickel is an increasing function of turbulence, time and temperature. The rate of oxygen pickup in the 60-cycle furnace is about three times as great as in the 5000-cycle furnace. In the 60-cycle furnace the maximum oxygen content of the melt comes close to the saturation limit. Melting under an oxygen-free atmosphere prevents oxidation in both types of furnaces. DISCUSSION (Iloward Scott presiding) H. Scott, East Pittsburgh, Pa.—When Professor Desch was in Pittsburgh recently he mentioned that the induction furnace has practically replaced the crucible furnace in Sheffield except for the carbon tool steels. Dr. Hensel is to be congratulated on the development of analytical methods for determining inclusions and for getting two different methods to agree. F. R. Hesnsel—Recently the purification of molten metals with hydrogen or other suitable gases has become an important issue and a number of patents have been taken out covering gaseous treatments of molten metals. In this connection I wish to call

Jan 1, 1933

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.; METAL MINING TECH- NICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61 Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. O. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York specting for Ore Feb., 1928 101 Relation between the Oxygen Bal- G. St. J. Perrott, New York ance and Propulsive Strength of N. A. Tolch, Feb., 1928 Eight Gelatin Dynamites J. E. Crawshaw 102 Effect of Oxygen Balance of Gelatin G. W. Jones, New York Dynamites on the Gaseous Prod- G. St. J. Perrott Feb., 1928 ucts of Detonation 108 The Financial Report of a Min- Henry B. Fernald New York ing Company-Its Content and Feb., 1928 Meaning 116 What Duty to Support the Surface R. G. Bosworth New York Does a Subsurface Owner Owe? Feb., 1927 136 Comparison of Branch Raise and C. A. Mitke Los Angeles 76, 93, 103 Combined Shrinkage and Caving Sept., 1928 Methods 141 A Mining Company Balance Sheet G. F. Wolff New York Feb., 1928

Jan 1, 1927

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL.. . MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. Louis, Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y VICE-PRESIDENTS CHARLES W. GOODALE,1 . . . . District 5 BUTTE, MONT. MARK L. REQUA,1 District 6 SAN FRANCISCO, CAL. HENRY S. DRINKER, District 2 So. BETHLEHEM, PA. ROBERT M. RAYMOND,2 . . . . District 0 NEW YORK, N. Y. EDWIN LUDLOW,3 District 2 LANSFORD, PA. A. R. LEDOUX,3 District.0 NEW YORK, N. Y.

Jan 11, 1919

By Paul Soros

Terminal facilities were recently completed at Conneaut, Ohio, on Lake Erie, for the Bessemer and Erie Railroad Co. (a wholly-owned subsidiary of U.S. Steel Corp.) which may become the blue- print for all future coal shipping terminals. Design and engineering of the new facility was by Soros Associates, New York, N. Y. Unlike terminals of conventional design, for example, those at Toledo and Newport News, which load coal directly from the railroad car to the vessel, the new installation passes the coal into temporary storage, loads the vessel from temporary storage and provides alternative reclaiming systems in case of major system failure.

Jan 1, 1966

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

Oil-well driller with extensive experience in this line of work. Location, Bolivia, South America. Salary depends on experience. R.-789. Mining Engineer, with geological knowledge, who can locate suitable spots for drilling oil wells. Location, Bolivia, South America. Salary depends on man. R-788. Construction Engineer, mechanical or civil engineer with experience in installing oil plants for foreign field. Must be able to install entire equipment including tanks, piping, buildings, etc. Salary depends on experience. R-782. Geologist, competent petrographer for micropetrographic work and training of two assistant students under the direction of the Director of a Geological Institute. Engagement is for six months with option on the part of the Director for an equal period: Location, Mexico. Salary, 450 pesos Mexican gold ($225 per month). R-765. Operating Mechanical Electrical Engineer, with extensive experience in charge of the maintenance, repair, and betterment of all mechanical and electrical equipment on mining operations. Desirable that the man have had this experience in connection with phosphate mining. Applicant must be competent to direct shop repairs on motors and generators, including rewinding, the building and maintenance of transmission lines, etc. Must also have ample machine-shop experience to enable him to direct repairs of light locomotives, steam shovels, brown hoists, caterpillar tractors, and auto trucks. Duties will include the betterment and maintenance of phosphate-rock washers and rotary-work dryers. The applicant must also be competent to conduct efficiency tests on all such equipment and be enabled to interpret data collected. Splendid opportunity for the right type of man. Climate and living conditions excellent. The company will furnish house rent free, including light .and water. Location, Florida. Salary depends on experience. R-854.

Jan 7, 1919

FRANCIS B. SILSBE,* Washington, D. C. (written discussion?). ?This paper is an interesting example of the -solution by the methods of metallography of what seemed at first a purely chemical problem. The authors have shown: in detail, how the well-known corrosion of spark-plug terminals is due to the dropping out of the individual crystals of the metal as it becomes surrounded by an oxide film. This corrosion is usually quite slow but in special cases may become a serious factor in limiting the life of spark plugs. There still remains the problem for the metallurgist to produce a material that will be entirely free from, this trouble. One of the most startling results of the work is. the demonstration that it affords of the deleterious effect of a mechanical stress continuously applied to material that is at the same time subject to adverse chemical or thermal conditions. The particular style of spark plug shown in the illustration, and in which serious trouble was caused by this corrosion, has the side terminals fastened at both ends and the method of assem-bling is such that a considerable initial tension is applied to the wire. It is without doubt this superimposed tension that causes the inter-crystal-line network to line up, as it were, into a few continuous and deeply penetrating transverse fissures instead of forming a great number of shallow surface cracks. This result is clearly shown both in the case of

Jan 11, 1919

By Thomas M. Dr. Drown

IN experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By Thomas M. Drown

In experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

NORMAN B. PILLING (author's reply to discussion *).-The discussion by Mr, Bassett raised one or two points that deserve further discussion. The printed figure for the lead content of the copper used was 0.015 per cent. and not 0.15 per cent., upon which his comment was based. A copper having the latter figure would, of course, be quite unusual. Mr. Bassett takes exception to the writer's statement regarding the distribution of cuprous oxide in wrought copper and states that "the FIG. 1.--ROLLED AND ANNEALED SHEET. ETCHED WITH AMMONIA AND HYDROGEN PEROXIDE. X 75. eutectic of copper with cuprous oxide is usually found between the crystals of pure copper, whether in the cast or the wrought form." While it is very well known that during the solidification of cast copper the cuprous oxide is segregated completely as an envelope of cuprous oxide-copper eutectic around the crystals of copper free from oxide, it is the writer's opinion that, as a result of repeated rolling, this eutectic structure is quite destroyed and the small particles of cuprous oxide become widely scattered, and in the recrystallization following, during annealing, the rearrangement of the grain boundaries takes place with much indifference to the actual distribution of these particles. In the accompanying micrograph, taken from a rolled and annealed sheet, the random distribution of the small cuprous-oxide particles with reference to the location of the grain boundaries may be seen.

Jan 3, 1919

By R. D. Reiswig, D. J. Mack

THE use of pyrophoric alloys in ignition devices dates back more than fifty years to a German patent granted to Carl Auer von Welsbach in 1903.' This patent named a composition essentially the same as that used in most present-day cigarette lighter "flints:" 70 pct mischmetal, 30 pct Fe, referred to here as "Auer alloy." Among the few current exceptions to this composition are those "flints" based on titanium or zirconium. The rare-earth metals of which mischmetal is composed are so similar chemically and physically remarkable similarity in their alloying behaviors would be expected. Comparison of the binary phase diagrams2 of these elements with nonrare-earth metals shows that this is true to a striking degree, so much so, in fact, that it appears that a mixture of these elements may be treated as a single component of alloys without fear of serious error. In considering alloys containing mischmetal, therefore, the mixture of rare-earth elements will be referred to merely as "cerium," the predominant element in mischmetal. In polishing cerium alloys for metallographic examination, it was soon discovered that aqueous polishing media were highly corrosive. Free cerium in the alloys acts similarly to calcium (though not quite so rapidly) in evolving bubbles of hydrogen at the metal-water interface; thus, special metallographic techniques are required. The simplest polishing technique found to be satisfactory consisted of slow hand grinding on dry emery papers through

Jan 1, 1956

By H. C. Rolseth, R. H. Kohler

Jet channeling made its entry into the granite industry in 1955 and quickly gained acceptance as an economical method of quarrying. Developed by the Linde Division of Union Carbide Corp., this method employs a small rocket-jet burner with a high-temperature, high-velocity exhaust flame that causes granite to disintegrate. It can thus make continuous vertical cuts to free large blocks from granite formations. The Thermal Spalling Process The effect of a thermal device on rock depends upon the rock's spallability. In simplest terms, spalling is the decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses.1 the individual rock properties influencing the spalling characteristic are so numerous and their interaction is so complex that it has so far been impossible to predict with accuracy the reaction of any particular rock to a high-temperature source of heat. Perhaps computers will eventually make such predictions possible, but for the present it is necessary to impose the thermal shock conditions on a sample of the rock to establish its spalling characteristics. The properties most favorable to a high degree of spallability are: (1) Large linear thermal expansion at temperatures below 700º C. (2) High thermal diffusivity at temperatures below 400º C. (3) Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. (4) No significant amounts of soft, low-melting, or elastic minerals or materials which yield after thermal decomposition.

Jan 7, 1969

By Warren Blauvelt

IN VIEW of the enormous wastes of natural resources, of labor and of capital, due primarily to the economic environment, established by legislation, the general neglect of this phase of the problem of the elimination of waste is difficult to understand. In such a study, the engineering method of attacking a problem should be employed. The engineer does not try to solve his problem by disregarding natural laws, but by utilizing them. The successful engineer establishes an environ-ment in which forces, acting in harmony with natural laws upon an object or objects, will produce the desired results. The engineer who notices that the water level in a vessel, into which a gallon of water per minute is flowing, is two feet higher than the level in an adjacent vessel, connected therewith by a 6-in. pipe, does not assume that the law of gravity has ceased to work, or that water no longer seeks its level; he examines the connecting pipe for obstacles which prevent the free flow of water. Some editors, many reformers and most politicians tell us that the law of supply and demand no longer works; hence governmental control of commerce is necessary. Governmental control may temporarily-that is, until trial proves its futility- "insure domestic tranquility" and "promote the general welfare;" but it cannot "secure the blessings of liberty" which it cur-tails, nor can it "establish justice" which it violates.

Jan 9, 1922

By S. Fugleberg

As a result of research work done during the planning of the Kokkola zinc plant it was found that a very efficient cementation of impurities from the suspension obtained after leaching copper and cadmium cakes was achieved by adding zinc dust to the batch without filtration after the leaching. All elements nobler than cadmium are precipitated with the exception of lead, which must be removed in a separate step. Using pure zinc dust, free from noble metals, the cadmium sponge produced will only contain elements that can be re- moved from cadmium by meltrefining. The process is thus : 1. Leaching and purification 2. Removal of lead (with BaCO3) 3. Precipitation of cadmium sponge with pure zinc dust 4. Meltrefining of briquetted sponge with NaOH for removal of Zn (and others) The paper deals with the removal of the most critical elements, i.e. Co, Ni, As, Sb, Cu, Pb, T1 in the liquid phase and Zn and T1 in the melt. A survey is also given of the behaviour of most of the other elements normally found in Cd raw material, such as Ge, Te, Se, Sn, In, Ga. It is shown that in most cases the benefit of an electrolysis in Cd production is very limited. In Kokkola 99.998% Cd is achieved by this method, but in favourable cases it may be possible to come quite close to five nines.

Jan 1, 1973

By G. B. Craig, J. Rezek

The critical resolved shear stress of zone-refined zinc single crystals deformed in tension is found to increase with increasing amount of striation substructure. The increase in strength with numbers of striations can be accounted for by a dislocation pile-up mechanism. A somewhat different means of plotting stress-strain data is introduced which allows a more unambiguous choice of yield stress to be made. FEW systematic studies of the role played by mac-romosaic or striation-type substructure in the de- formation of high-purity metal single crystals grown from the melt have been reported. McGrath and Craig' found that striations increased the critical resolved shear stress of zone-refined aluminum crystals, postulating a dislocation blockage by the striations as the strengthening mechanism. Lauri-ente and Pond2 found that, as the etch pit density increased in aluminum crystals grown from the melt, the critical resolved shear stress also increased. Fleischer and Chalmers3 also found changes in the critical resolved shear stress of aluminum crystals grown from the melt at varying rates, but could not be certain whether an increase of strength with rate was due to a higher concentration of impurity in the gage length or to an increase in the number of small-angled boundaries. An early work by Hibbard4 indicated that copper crystals containing lineage boundaries were stronger than those free from this type of imperfection.

Jan 1, 1962

By T. E. Leontis

Several publications1-7 during the past few years have demonstrated the markedly greater effect of cerium, as compared to all other alloying elements, in enhancing the strength and creep resistance of magnesium at elevated temperature either with or without the presence of other elements. In the work reported in Ref. 1-6, the cerium was added in the form of Mischmetal, which contains all the rare earth elements in essentially the same proportions as they occur in monazite sand, the principal ore of these metals. Mellor and Ridley7 have presented the creep characteristics at 200°C of magnesium alloys prepared both with pure cerium and with Mischmetal. Up to the present time, however, no comprehensive study of the effect of the various component elements of Mischmetal on the properties of sand-cast magnesium has been made. This hiatus in magnesium technology undoubtedly is associated with the difficulty in obtaining the rare earth metals separately. This investigation provides such a survey, the object of which was to determine which of the elements present in Mischmetal contributes the greatest effect in developing high strength and high resistance to creep at elevated temperatures. Toward this end the compositional variation of these properties has been determined as a function of temperature in the following alloy systems: 1. Magnesium-Mischmetal 2. Magnesium-cerium-free Misch- metal 3. Magnesium-didymiuin 4. Magnesium-praseodymium- lanthanum 5. Magnesium-cerium 6. Magnesium-lanthanum This designation, based on the names of the metals as furnished by the producer, is used throughout the paper in order to avoid the complicated system of listing all the elements present in the more complex alloys. The composition of the metals and the alloys is discussed in detail below. Preparation of Alloys ALLOYING INGREDIENTS The chemical composition of each of the six alloying ingredients used to prepare the alloys reported in this paper is given in Table 1. In each case, the percent total rare earths, percent cerium, percent neodymium, percent praseodymium, and percent thorium were determined in addition to the listed impurities. The percent lanthanum was determined by difference from the total rare earth content and consequently includes the other elements (samarium, terbium, yttrium, etc.) present in Mischmetal. These additional elements, however, seldom amount to more than 1 to 2 pet of the total rare earth content of Mischmetal. The iron content of the Mischmetal is considerably lower than that of the other metals. This grade of Mischmetal is now readily available. The metals are listed in the order of decreasing complexity. Elimination of the cerium from Mischmetal results in what the trade calls "Cerium-free Mischmetal." Carrying the separation a step further by eliminating the lantha-

Jan 1, 1950

By Henry J. Schwellenbach

Lack of a system in scheduling the replacement of capital equipment can result in emergency purchases of units which may later be found unsuitable for the job. New York Trap Rock Corp., which produces crushed stone for use as construction aggregate, was faced with just such a situation some years ago. The company replaced capital equipment only when machinery in use was no longer serviceable, or when there was an obvious need for different equipment. Operating and maintenance costs were generally neglected because an efficient method was lacking. New York Trap Rock has four plants located along the Hudson River, all within 70 miles of New York City. Crushed stone output-6 million tons a year-is moved to markets in metropolitan New York, New Jersey, and Long Island areas by water transport. Customers are contractors with ready-mix concrete and asphalt plants located on the water.

Jan 10, 1959

By G. R. Speich

RECENT studies by Smith and Olney,1,2 Olney,3 Greifer and Salli,4 Rys etal., and Olney and smith 6 have established that graphite is the first decomposition product to format the surface of hypereutectoid plain-carbon steels when they are austenitized in a vacuum or inert atmosphere and slowly cooled. This graphite evidently forms directly from the austenite and only at the surface of the specimen. The interior of the specimen is found to be free of graphite. The graphite layer can almost completely cover the specimen surface and the rate of its formation is markedly sensitive to the orientation of the austenite. The present work was undertaken to study this phenomenon further, especially with regard to the effect of temperature and austenite orientation. The material studied in this work was a high-purity iron-carbon alloy containing 0.88 pct C, 0.005 pct Mn, 0.016 pct Si, 0.005 pct S, and 0.002 pct P. Specimens were heat-treated in a commercial hot stage modified for rapid quenching.7 This permitted direct observation of the formation of the surface graphite. A vacuum of 10"" to 10-5 mm of Hg prevented oxidation or decarburization of the specimens. Specimens were austenitized for 30 min at 1100°C and quenched to a series of lower temperatures where they were isothermally transformed. Surface graphite was observed to form at 700°, 750°, and 780°C but not at 825°, 900° or 1000°C. Since the maximum solubility of austenite for graphite is 0.88 pct C at 800°C,8 surface graphite only forms at tem-

Jan 1, 1962