Search Documents

By M. Stuart, R. F. Down

The Copper flotation concentrate produced at Gortdrum mines contains about 1% Hg. This article deals with the treatment used to produce a substantially mercury-free copper concentrate. Metallic mercury is a byproduct. Nearly all the mercury in the Gortdrum concentrate is present in the copper mineral tennantite-tetrahedrite. This mineral is variably distributed throughout the ore body so that by selective mining it was possible to produce salable concentrate relatively low in mercury while the treatment plant was being built. Roasting was the only feasible method found for removing the mercury from the concentrate, and it was decided that this should be done in an atmosphere with limited oxygen. A multiple hearth furnace is used. Mercury soot is condensed from the gas stream and treated to produce prime virgin mercury. Problems were experienced at first with materials handling, oxygen control, cooling of the calcined concentrate, treatment of the mercury soot, and in the metallurgical accounting. Precautions were necessary to avoid health problems. The plant is now operating reasonably well. The value of the mercury produced does not warrant the cost of the plant but without it, the copper concentrate could not be sold.

Jan 1, 1975

By Tadao Nagai, Masao Sato

Electrochemical measurements have been carried out in an auto- clave to investigate the electrochemistry of hydrogen precipitation of nickel from acetate buffered solution. After having previously obtained the rate equation for this reaction we have now made a concentrated effort to explain the rate equation electrochemically. A saturated NaC1-type Ag/AgC1 reference electrode has been improved so that it can be used in an autoclave. Polarization curves for the reaction, [H2=2H+ + 2e,] on nickel electrode were measured in solutions free from nickel ions at 185°C, and the parallel curves were obtained by changing PH2 and pH for normal and reverse reactions, respectively. Polarization curves in nickel solutions were complex, probably because the potential of hydrogen electrode is close to that of nickel and of the nickel surface altered during polarization. Then the nickel electrode potential and the reaction rate were measured simultaneously during pressure reduction at various hydrogen pressures and at various nickel concentrations. The reaction rates in terms of current density were plotted to obtain the local polarization curves for reactions Ni2+ + 2e ? Ni and H2 ?2H+ + 2e. The anodic and cathodic local polarization curves exhibit potential dependency. Therefore it is likely that the pres- sure reduction can be regarded as a coupled electrodes reaction.

Jan 1, 1973

By Clinton H. Crane

DR. TILNEY, the great expert on the study of the development of the brain of human beings and animals, tells us that the greatest difference between the human brain and the brain of animals is that man alone has shown evidence of being able to predict the future. Just why he throws overboard the busy bee who lays up honey for the winter, the squirrel who gathers nuts, and the humble ant, I do not know. At any rate, it is nice to be assured by an authority that we have this power of prophecy. My own experience with attempting to prophesy the future has convinced me that our only possibility of being good prophets is to be good students of history.

Jan 1, 1940

By AIME

ENGINEERS have long pondered the answer to the question of "How am I doing?" and in large measure the answer from the economics angle is provided by the 1946 survey of the engineering profession now being published by the Engineers Joint Council as an eighty-page bulletin entitled "The Engineering Profession in Transition." The survey, based upon a completely precoded mail questionnaire, aimed at three major objectives: (1) to determine the general impact of World War II upon the profession in the period 1939 through 1946; (2) to obtain re- R liable data from which valid findings could be derived to predict how active the profession would be after 1946; and (3) to determine if the war's upheaval had changed materially the pattern of professional activities, education, background, and earnings from those which existed prior to 1939. Abundant data on the economic status of the engineer based upon years of experience in his particular field, the specific branch of the industry in which he served, and his educational background are presented. Relationships between years of experience

Jan 1, 1947

By D. R. Knowlton

IF I were a minister, and this were a sermon, and such a passage appeared in the Bible, I would choose for my text: "From whence cometh the oil for our war?" And no preacher was ever more serious than I am. You petroleum engineers recognize that the producing branch of the industry is passing through an era of plenty and inflated potentials into an era of scarcity and unmet allowables. Not too long ago the oil operators of Kansas, California, and Texas were appearing before operators' meetings and regulatory authorities asserting that these States were capable of producing at rates far in excess of what the demand at that time would absorb. Today every oil-producing area in the United States except the Texas Gulf Coast and West Texas is producing close to or in excess of its maximum efficient rate.

Jan 1, 1943

E. Hill, South Norwalk, Conn. (communication to the Secretary*) :—The phenomenon described by Dr. Ledoux, involving an apparently abnormal high temperature in the air-cylinders of compressors, has not been, so far as I know, discussed in technical literature. The common formula for the adiabatic compression of dry air does not account for heat suficient to flash ordinarily decent cylinder-oils, nor do the text-books include in their theoretical statements any quantitative consideration of the effect of leaks in the ideal machines which they contemplate. This lack I have endeavored to supply by preparing, in the form of a circular, for the use of the customers and correspondents of the Norwalk Iron-Works, a brief mathematical

Jan 1, 1904

By Robert T. DeGavre

The $650 million financing for Into Ltd.'s Soroako nickel project is a story worth telling-not only because the project itself represents a significant achievement but also because there are certain important lessons that can be derived from our experience in financing the project. A critical appraisal of the methods and successes in the financing plan is presented in this article, in light of goals which Inco sought to achieve. A technical assessment of the project is not included, since Inco Ltd. has submitted a series of papers on this subject at the International Laterite Symposium as part of the 108th Annual Meeting of AIME in February 1979. Progress in developing and financing the project is encapsulated in the accompanying project factsheet.

Jan 3, 1979

By W. E. C. Eustis

1st. THE fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down in an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contain-, no phosphorus or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con¬sequently the resulting iron should be free from both of these impu¬rities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferronmanganose. I have merely given above the rough outlines of the process, but it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By Richard M. Foose

Five miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. Geology Lower Cambrian Antietam quartzite and the Rilontalto quartzite, stratigraphi-cally older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65" to vertical. The clay crops out at an elevation of about 1000 feet. Origin and Character The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there Are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about loo ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: SiO2, 67.05 per cent; Al2O3, 22.27; Fe2O3, 0.40; CaO, 0.00; TiO2, 1.05; MgO, 0.52; Na20, 0.04; K2O, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1948

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By R. V. Riley

IN the metallographic examination of the alloys of iron and silicon, several investigators1-' have reported on the occurrence of an unusual type of etched structure, particularly in the alloys of higher silicon content. This, the so-called "barley shell" structure, has been observed with iron-silicon alloys over a wide range of silicon content, and under certain circumstances it can be seen upon the micro-sections of pure iron. The barley shell structure may be demonstrated most easily with iron-silicon alloys in the range 8 to 20 pct Si after etching in a hydrofluoric acid base etchant. Two etchants which produce the structure are: Corson's reagent, which is 2 parts hydrofluoric acid, 1 part nitric acid, and 2 parts glycerol; and picric acid reagent, which is 1 part hydrofluoric acid and 1 part saturated solution of picric acid in alcohol. Both when freshly prepared and used for etching commercial silicon-iron alloys containing 14 to 16 pct Si, invariably produce the barley shell structure shown in Fig. la. It is now well known that the barley shell structure is a pseudomorph and the true structure of an alloy of this composition consists of a single phase of silico-ferrite together with graphite as shown in Fig. lb. Lower silicon alloys and even pure electrolytic iron may also be etched in the above reagents to give the barley shell provided the etchant has been either: 1—Stored in contact with glass or silica, or 2—used previously for etching an iron containing silicon. Pure iron etched in perfectly pure hydrofluoric acid base etchants free from silicon contamination gives a normal structure free from the barley shells. Therefore, although the hydrofluoric acid in the reagent primarily is responsible for the barley shells, silicon, or its compounds, also must be present, either in the etching reagent or in the specimen. It was of considerable interest to the author to read the paper by Wachtell,? in which the barley shell etch was deliberately used for the identification of the boundaries of high and low silicon areas in diffusion experiments made upon laminate bars of compacted and sintered pure iron and ferrosili-con powders. This method of utilizing the barley shell etch is novel and in the hands of the investigator gave a useful differentiation between the high and low silicon areas in those specimens. For the reasons already given, however, the technique is not to be regarded as of universal application. Misleading results might be obtained, for example, if two or more specimens were etched in the same etchant. Fresh pure reagents only must be used each time. Provided this is done and the investigators are well aware of the limitations of the method, then the barley shell pseudomorph can be made of limited use in distinguishing between higher and lower silicon areas in a microspecimen of a ferrous material. The greatest of care must be exercised in the interpretation of the results which may be regarded as qualitative only and may, in fact, not be specific to silicon alloys.

Jan 1, 1952

By B. L. Averbach, Morris Cohen, L. L. Seigle

Free energies, enthalpies, and entropies of mixing of Ni-Au solid solutions containing 5 to 95 atomic pct Ni have been determined by the electromotive force method at 700° to 900°C. The thermodynamic activities exhibit large positive deviations from Raoult's law, and the entropies of mixing are almost twice those of ideal solutions. The enthalpies of mixing are positive (heat is absorbed) and are attributable to the lattice distortional energy resulting from the size difference between the nickel and gold atoms. This factor appears to be responsible for the miscibility gap at lower temperatures. IN the thermodynamic study of metallic solid solutions, most interest has been directed toward systems with negative deviation from Raoult's law, namely, those exhibiting superlattice or compound formation. The results of previous investigations are summarized in recent publications.'-' Relatively little experimental work has been carried out on solid solutions which manifest a positive deviation, possibly because the range of solubility in such cases is usually quite limited. Nevertheless, the relationship of the thermodynamic properties of these solutions to diffusion, nucleation, and precipitation in the solid state are of considerable importance. The binary Ni-Au alloys are particularly suited to an investigation of these relationships. Despite the presence of a miscibility gap at lower temperatures, Fig. 1, indicating a large positive deviation from Raoult's law, complete solid solubility is found above 840°C. Moreover, the difference in the atomic scattering powers of nickel and gold is sufficiently great to permit X-ray diffraction studies of atomic arrangements and pre-precipitation phenomena. Radioisotopes of both nickel and gold are available for diffusion work, and finally, a large difference in nobility between the two elements facilitates measurement of the thermodynamic properties. The present paper describes the experimental determination of the free energies, enthalpies, and entropies of mixing of solid Ni-Au alloys. Table I gives a list of the symbols used in the paper. Experimental Method The stability of nickel chloride relative to gold chloride" indicated that the galvanic cell method could be used for determining the thermodynamic properties of Ni-Au alloys. An electrolytic cell (Fig. 2) was constructed, similar to that of Weibke and Matthes,7 in which the electrodes were solid nickel and Ni-Au alloys, and the electrolyte was a fused mixture of alkali chlorides containing NiCl,. The cell electrodes were made from fine gold granules and carbonyl nickel shot melted together under argon, chill cast, swaged to 1/16 in. diam rod, and annealed for one week at 850°C. Commercial reagent and chemically pure grade salts, purified by dehydration, were used for the electrolyte. The cell, operating in an atmosphere of purified argon, was heated in a resistance-wound cylindrical furnace whose temperature was controlled to within ±0.5ºC. The potential developed between the pure nickel and the alloy electrodes, which is related to the thermodynamic properties of the alloys by standard equations to be presented later, was measured with a potentiometer and a mirror galvanometer sensitive to 10-7 v. Dehydration of the electrolyte was carried out in the assembled cell by evacuating at 100°C for about

Jan 1, 1953

By D. Weinstein

Yieldilzg in annealed arc-cast molybdenunz in torsion was studied as a function of strain rate and tem-perature. The temperature dependence of the yield point for different strain rates was used to calculate a heat of activation for the yield point. The heat of activation was not a constant but was approximately a linear function of the stress at yield. It is proposed that the rate effect in yielding is determined in part by a site place-change of C (or other interstitial atom) in the metal. THE low-temperature embrittlement phenomenon in metals and alloys has been known to exist for a long time. Although a transition from ductile to brit-tle behavior has been observed in some close-packed hexagonal metals1 and a face-centered cubic alloy, the most common class of metals exhibiting this be-havior has a body-centered cubic lattice structure. For example, a ductile to brittle transition has been observed in iron,3 molybdenum,4 chromium,5 colum-bium,6 and tungsten.7 In the present investigation, molybdenum specimens were tested in torsion over a wide range of temperatures at three widely separated strain rates, and the temperature for onset of embrittlement was determined. Characteristic of body-centered cubic metals and closely associated with plastic deformation is the appearance of a sharp upper and lower yield point. Theoretical explanation of the yield point in iron and low-carbon steel is due to Cottrell,8 who attributes the phenomenon to the pinning of dislocations by the formation of impurity atmospheres around the dislocations. These atmospheres tend to lock the dislocations and make them more difficult to move. The stress required to move a dislocation and thereby cause plastic deformation is greatly increased, and thus an upper yield point is observed. In addition, theoretical analysis,9 as well as experimental observations, show that the upper yield point is strongly a function of temperature. The upper yield point is observed to decrease with an increase in testing temperature, and above a certain temperature (-700° K in iron) it no longer appears. This is consistent with the concept that thermal vibrations will help free a dislocation from its atmosphere, so that the external stress required to free a dislocation from its pinning atmosphere decreases with increasing temperature. Furthermore, with increasing temperature the equilibrium concentration of impurity atoms around a dislocation decreases exponentially with the result that the dislocation is less firmly pinned. In Cottrell's theory of yield point a static model is visualized in which the pinning atmospheres, particularly interstitial atoms, are immobile, and the dislocations are anchored to stationary positions in the lattice. However, experiments1,7 show the upper yield point to be time-dependent or a function of the rate of straining, a high strain rate causing a high upper yield point. Present theory does not adequately account for the rate dependence of the yield point, and the exact function of the interstitial atom is not under stood. Nevertheless, observation of the temperature dependence and rate dependence strongly suggests that the upper yield point phenomenon is due to the interaction between dislocations and pinning atoms, and that a diffusion mechanism is important in determining the yield point.

Jan 1, 1962

By F. Keller

ALUMINUM alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenth1 of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was com-pleted in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound Mg2Si caused a noticeable decrease in the solid solubility of Mg2Si in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of Mg2Si in aluminum was 1.85 per cent at 595° C. and decreased to 0.30 per cent at 300° C. The results of the latter investigation were used as the basis for the present work.

Jan 1, 1936

By W. E. C. Eustis

1st. The fine iron ore is mixed with a sufficient proportion of fine coking coal, and is coked in any of the ordinary methods for making coke. The effect of this is to convert the iron oxide into sponge in such a shape that the usual trouble of oxidation is avoided. 2d. The resulting mixture of coke and sponge is melted down ill an ordinary cupola, the coke furnishing more than sufficient fuel for that purpose. I may briefly point out here that in the first place the iron is sponged, and this sponge, as is well known, contains no phosphoras or silicon when the reduction takes place at a low temperature; and in the second place this sponge is melted down in a cupola in which there is no zone of reduction for phosphorus or silicon, and that con . sequently the resulting iron should be free from both of these impurities. 3d. The liquid sponge, now carburized, is run into an open-hearth furnace, where the requisite degree of hardness or softness is obtained by adding some of the fine ore, and the usual dose of ferromanganese, I have merely given above the rough outlines of the prows, bat it is my intention, as early as possible, to bring the process more fully before the Institute.

Jan 1, 1881

By R. M. Hudson

Equilibrium constants have been determined for the jeaction C (in steel) + H2O = CO + H2 as a function of carbon content (0.013 to 0.74 ujt pct) and temperature (1200° to 1800°F) by using a flow system in which the water-vapor content of various gas mixtures containing hydrogen, carbon monoxide, and nitrogen was systematically controlled. The equilibrium partial-pressure ratio K1 = PcoPH2/PH2O was obtained for two low-carbon steels and four Fe-C binaries from a series of runs made at each temperature. By comparison of Ki with the analogous ratio for the reaction C (graphite) + H2O = CO + H2, the activity of carbon in steel (ac) was comDuted for each temperature and carbon content studied. From these data values of the equilibrium constants for two other carburization-decarburiza-tion reactions of importance were estimated. The chemical compositions of the two steels and four Fe-C binaries used are given in Table I. Specimens of Steel E were cut from a 0.035-in.-thick commercially box-annealed and temper-rolled lot of a low-carbon low-metalloid steel. Steel F was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to a 0.059-in. thickness. Fe-C binaries A, B, C, and D were vacuum-melted and poured, hot-rolled, pickled, and cold-reduced at the Laboratory to furnish specimens 0.035 in. thick. Sheet specimens were cut from all lots to approximately 3/4 by 3 in. by gage and were vapor-degreased with trichlo-roethylene and weighed before heat treatment. Heat treatments were carried out in a hinged-top Hevi-Duty electric furnace with a Vycor-glass tube. When the furnace was at the desired

Jan 1, 1965

By P. F. MINISTER

AT Lime Spur, Mont., the East Butte Copper Mining Co. has been quarrying limestone for twenty years. The quarry is beside the Northern Pacific R. R. in the Jefferson River canyon, 4 ½ miles east of Cardwell, at Lime Spur, Montana. HISTORY This quarry was opened early in 1900 by Dan Morrison of Whitehall, the discoverer of the Morrison cave, to supply a demand for smelter flux. Limestone was sold to the Pittsmont smelter of The East Butte Copper Mining Co. and to the Butte Reduction Works. As no particular effort was made at the quarry to select the rock that delivered to the smelters was unduly high in magnesia and impurities. The East Butte com¬pany, therefore. Bought the quarry. in 1909 and confined operations to the high-grade beds in order to supply rock of the desired purity for its own smelter and the Butte Reduction Works until the latter shut down. It also developed a market for some of its rock with the sugar factories. The latter market increased until in later years all rock, larger than 4 in. in size over a bar grizzly, was being shipped to the sugar factories, and the rock smaller than 4 in. was being used as a flux in the blast furnaces at the Pittsmont smelter. In 1924, the East Butte concluded a contract with the Anaconda company for the treatment of its ores, and the Pittsmont -smelter -was shut down: which made the minus 4-in. rock a useless by-product. Since there was not enough revenue in the sugar rock alone and also because of limited waste room it became necessary, if Lime Spur was to continue to operate, to increase- the proportion of plus 4-in. rock and to develop a market for the minus 4-in.

Jan 1, 1930

By C. E. Birchenall, H. M. Schadel

Vapor pressure of silver over silver-gold alloys has been measured over a range of temperatures for four compositions. Orifice effusion has been compared with electromotive force measurement as a means for determining thermodynamic activities in these solid metallic alloys. Correlated activity coefficients are given for silver-gold alloys for the temperature range 200' to 1000°C. SOUND development of a technique for the measurement of some property of matter requires a comparison with other recognized procedures which have been used to measure the same property. Such a check is especially useful if the assumptions on which the applications stand are basically different for the two methods. Agreement in the results tends to confirm both sets of assumptions. The electromotive force method for determining thermodynamic activities depends upon the reversibility of the electrode processes and a knowledge of the valence states involved. The orifice effusion technique of determining vapor pressures requires that certain mean free path conditions be met, that the state of association of the vapor be known, and that efficient collection of vapors be maintained. Thus the requirements are quite different in nature. Although procedures often exist by which the fulfillment of these conditions may be tested internally, agreement of thermodynamic activities for a single system obtained by both methods constitutes a more severe test of the assumptions. The binary alloy system silver-gold is excellent for this purpose for several series of emf measure-

Jan 1, 1954

By Charles H. Fulton

THE Engineering Education group began its sessions Tuesday morning, Feb. 16, as a Committee and wound up the day as the Institute's fifth " Division." C.II. Fulton presided. The first paper for discussion was entitled "Teaching Management in Engineering Schools,"' by Eugene McAuliffe, president of the Union Pacific Coal Co., space for which may be found later in these pages. In it, Mr. McAuliffe argued that an engineering student should be taught the knowledge of men, much as a medical school teaches surgery. He then went on to indicate, out of the wealth of his administrative experience, the problems an executive needs to be equipped to handle, and said that every student engineer should look on himself as a potential manager.

Jan 1, 1932