Search Documents

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general. our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2-by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn ;7± MnO + Fe [A] slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aFPI OFeO ? aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term aFe may he combined with K" to give a new constant K'. Making these changes.

Jan 1, 1942

By A. M. Gaudin, C. S. Chang

IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.1-4 The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods.5-6 In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba140 to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,4 were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand picked quartz, washed free of stains, were reduced in size to -20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This -200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then' was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn,, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.7 The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74 micron quartz particles, using a surface factor of 1.96,8 is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1952

By T. V. Moore

DURING 1910, crude-oil production in the United States reached a record level averaging about 3.700,000 barrels daily. Export declined sharply while imports increased with the result that large quantities of crude oil were run to storage during the year. Imports consisted largely of residual fuel oil brought in from South America bit because of a shortage of that product in this country and of Mexican crude. The price of petroleum products followed the declining trend of the last three year resulting in serious disparity between crude and product prices. This condition was aggravated in some areas by the increasing production of distillate by recycling operations and by the high tanker rates prevalent in the last two months of the year. As a result two small purchasers found it necessary to reduce crude-oil price in the Corpus Christie area of Texas.

Jan 1, 1941

By Frank H. Kingdon

and eventually we would have trouble. That is, these little localized overstresses may not be important if the structure is loaded a few times, but may be important if the structure is loaded many thousands of times. The existence of localized stress has been demonstrated by direct experimentation with delicate extensometers by the elaborate investigations of Coker. Localized stresses four, five, and six times those that we would get by the ordinary laws of mechanics exist in most of our structures. These stresses, ordinarily, under steady load do no damage but if they are repeated many times may start progressive failure. So far, we have seen no failure that could not be explained by localized high stress at a nick, a crack, a point where one heat treatment stopped and another began, or where there was local faulting, or any one of a dozen causes. In the case of drill rods, the actual distribution of stress must be different from that which any mathematical analysis could predict. It would seem that the spread of damage from the localized overstresses, so far as we can see now, explains the phenomenon known as fatigue. The Ideal Drill Steel By Frank H. Kingdon The essential qualities of a drill steel are: (I), It must be easily forged; (2), the forged bit end must permit easy heat treatment to obtain hardness to resist chipping; (3)) the bar or body must be stiff to resist bending or twisting and yet tough to resist shock and vibration, with resulting breakage, (4), the forged shank end must be easily heat treated to obtain hardness with great toughness. Minor requirements are that the bit and the shank are in alignment with the body; that the shank is of the proper shape and length and the shank collar or lugs of the proper diameter and length; that the hole is free from obstruction; that the striking end of the shank is flat and square; that the bit is of the proper shape, with the cutting and reaming edges formed full and to the required size; that the reaming edges are concentric with the axis of the steel, and that there are no sharp corners at the shoulder where the bit blends into the body. The essential qualities of a bit, are: That its shape be such that maximum cutting speed can be maintained for as great a distance as possible before wear of the gage and cutting edge reduces the speed of penetration to a point where a change of steel is made necessary; that the size or diameter of the drill hole corresponding to the gage of the bit can be maintained with the least possible reduction as the depth of the hole increases, and that the bit can be correctly and readily formed and heat treated. The following features of bit design require attention: Shape,

Jan 1, 1922

By A. E. Perkins

fractured ingot will show a complete diagonal structure. If the temperature is lowered, the equi-axed zone is larger and the pine tree growth is less. A small ingot, though, is prone to this columnar structure, even though the casting temperature is kept down. The speed of cooling after solidification is slower in the hollow ingot than in the solid, therefore the granulation, which takes place after the crystals have formed from the liquid metal, is apt to produce larger grains than in the solid ingot. This is not a detriment. The original crystal size is of much more importance. The size of the grains due to this granulation constantly varies in response to mechanical work and subsequent heat treatment. Surface weakness, as shown by seaming and checking on the exterior when working or by cracking in hardening, is in some measure the result of the surface stresses of the ingot when cast. The temperature of the ingot mold or speed of freezing of the exterior of the ingot is of great importance and much seamy and cracked steel is caused by a too quickly cooled skin. Ingots that are turned or milled all over will not seam very much in working, in fact they are practically free from seams, whereas an ingot rolled without a preliminary machining operation is full of seams and cracks, some long and some short. It has been said that these short seams and cracks in the surface of the bar are the result of elongated depressions in the surface of the ingot and that if an ingot is cast very smooth it should give fewer surface defects. This is partly true, but an ingot cast very hot and having a very smooth skin will crack and seam very badly in the mill, as will the surface of an ingot poured very cold, which is very crinkly, because of the low temperature of the metal. The cause of the cracks and seams in one is not the cause of the cracks and seams in the other. The tube method of hollow drill steel manufacture is superior to the older method because of: (1) Greater freedom from external and internal straining; (2) the inherent small crystal size; (3) absence of harmful segregation, resulting in weakness of wall of hole. (4) less liability for steel to crack in inside of hole during forging or hardening; (5) toughening effect, arising from mild steel wall of hole limiting the intense hardening on quenching. Breakage and Heat Treatment or Rock-drill Steel By A. E. Perkins, Pittsburgh, Pa. Actual figures showing the superiority of one section or another are difficult to obtain. In a given size of steel, however, the cruciform sec -tion shows the most breakage; it is inherently a weak section. It contains less steel per foot than any other standard section of the same size and when rolled the wings tend to cool off setting up cooling stresses.

Jan 1, 1922

HENRY M. HOWE, Bedford Hills, N. T. (communication to the Secretary?).-The authors valuable results as to the effects of the air-hardening temperature on high-speed steel may be summed up thus: Influence of Rising Air-Hardening Temperature on. High-Speed Steel Air-hardening microstructure Cutting Properties temperature S Austenite Grain Free Carbide Grains Boundaries Too low Small or Narrow Maximum Too soft undeveloped Intermediate, Well-developed Intermediate Little or even Best correct none Too high Coarse hide, even with Minimum . Weak, brittle, three-rayed crumbling stars Here the suggestion is that as the air-hardening temperature rises it causes two prominent effects, one helpful and the other harmful, the increase of the former exceeding that; of the latter up to a certain point, at which the steel is most useful, and then in turn being outrun by it. The first is the progressive dissolving of the free carbide in the austenite, increasing the stability of the red-hard state. The second is the progressive coarsening of the grains, and thickening of the intergranular cement, developing at last into spandril-like three-rayed stars of the 1,288° specimen. (2,350° F.) of Plate D, thus giving clear proof of incipient fusion, that is of crossing the solidus. This causes intergranular weakness. The individual grains may have great red-hardness, but they do not cohere. They approach the condition of a bag of emery grains.

Jan 6, 1917

By AIME AIME

ELECTRICAL methods of geophysical exploration attracted major attention at the three sessions devoted to geophysics on Monday and Tuesday. At the opening' meeting Monday morning Hans Lundberg gave the paper by himself and Folke Kihlstedt; he described the use of the Racom, discussed last year, and the method whereby it is possible to eliminate all but subsurface, effects in electrical exploration. In the discussion Theodor Zuschlag pointed out some of the theoretical considerations behind the field procedure. Karl Sundberg's paper on the effect of impregnating waters was presented by title only, and S. F. Kelly then gave an abstract of a paper on the electrical properties of ores, by J. J. Jakosky, R. N. Anderson and Clyde H. Wilson. , This dealt with an exhaustive series of laboratory tests on the variation of -conductivity of ore specimens with the frequency of the energizing current, and of the effect of moisture content in typical clays and gouges on their conductivities at various frequencies. Considerable discussion was provoked during which the authors came in for some-criticism on their measuring circuits and for their assumption that a solid conductor could be compared with linear ones. They were praised, however, for making a start toward a compilation of resistivities for ores and rocks. Dr. Slichter disagreed with them that the conductivity of an orebody was primarily capacitive. He also called attention to the fact that it was high time geophysicists adopted the standard physical expression of ohm-,centimeters or ohm-meters to express resistivities. This same point was the burden of the next paper,. "Uniform Expression for Resistivity," by Sherwin F. Kelly, presented by title only.

Jan 1, 1932

By Walter Mathesius

The use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100" F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible ' to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800" and 1,000" F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available. In an endeavor to obtain results, even with inadequate equipment, we find that, at many plants, the stoves are worked far beyond their capacity. This leads, in many instances, to a situation in which the coke saving in the

Jan 1, 1915

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By L. C. Armstrong

Twice in the past two years and in two widely separated localities-one near Williamsville, Mo., and the other in the Allard Lake district of Quebec- the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately intergrown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely.

Jan 1, 1949

By N. Standish

By contrast with viscometry and sedimentation, no actual measurements of the applicability of Stokes' law to steelmaking have ever been reported; instead, the proof for and against Stokes' law has been inferred from the frequently observed phenomenon that inclusions collect in the top scum and the bottom of ingots. As such proof is unsatisfactory, continued reference to Stokes' law in steelmaking, even as a model for calculating the terminal velocities of rising inclusions, should be avoided. In fact, all conclusions that have been reached regarding size, density, and viscosity on the flotation of inclusions could be made more rationally without Stokes' law. A worthwhile exception is that of Mitsche1 who in 1934 used Stokes' law to show not only the expected effects of size, density, and viscosity on flotation but also the beneficial effects of i) melting under a slag layer (now Electro Slag Refining); ii) treating melts with synthetic slags (Ref. 2 gives recent applications); iii) bubbling an inert gas through the melt (recent applications in Refs. 3 and 4); and iv) altering the solid/ liquid interface characteristics. At this point, it should again be emphasized that the boundary conditions for which Stokes' law was derived place enormous restrictions on the law but its application, as noted earlier, can yield useful results in some fields under certain conditions and within well-defined limits. When compared with inclusions, which may be solid or liquid, spherical or irregular, dispersed or coagulated, interacting between themselves and the melt, floating in a liquid which is in a state of motion of varying intensity5 and contained in vessels of various shapes and sizes that may change with time as in a solidifying ingot, the conclusion is obvious-Stokes'

Jan 1, 1969

By Robert L. Kidd

ONE time or another placer mining attracts the attention of a large number of people, because of the possible low initial investment, low operating cost, and quick returns. Much has been said about sampling and operating placer deposits but many are still inclined to jump at a property without giving much, if any, consideration to proper sampling. This statement does not apply to experienced mining engineers but I am hoping that readers will tear out this article and pass it along where it will do the most good and thus help to preserve the reputation of legitimate mining. It would appear that some people have an ability to sink test pits in high-grade gravel that is positively uncanny. One pit showing high-grade values proves to some property owners and promoters that the entire property will do the same. This is

Jan 1, 1937

By Jack Washburn, E. R. Parker

Kinking in zinc single-crystal tension specimens was observed under conditions of low stress and high temperature. Kinking is discussed in relation to other plastic bending phenomena on the basis of dislocation theory. Experiments on the stress-induced motion of small angle boundaries are reported. KINKING was first reported by Orowan1 as a new deformation mechanism. He observed the phenomenon in cadmium single crystals loaded in compression. Glide lamellae in a local region of the rod were observed to snap over suddenly to a tilted position, resulting in a sudden shortening of the specimen. Between the tilted portion and the rest of the crystal there were fairly sharp boundaries, with the slip plane assuming approximately mirror image positions on opposite sides of these boundaries. Orowan considered the boundaries to be regions where dislocations had concentrated. Hess and Barrett' observed the formation of kinks in critically oriented zinc compression specimens. It was found that the sudden snapping over of the tilted region was not an essential part of the kinking phenomenon but rather was associated with the method of loading. Kinking was explained on the basis of the accepted mechanisms of slip and flexural glide. It was also suggested that a kink can be considered as a special type of deformation band. During a recent investigation of the effect of surface condition on creep of zinc single crystals," a similar phenomenon was observed in crystals which were loaded in tension. The specimens were 0.4 in. diam cylindrical rods with a free length of 4 in. between end connections. All of the crystals were tested at a constant load. adjusted to give an extension rate of approximately 0.05 pct per hr. Kinking, as shown in Fig. 1, occurred in some of the tests performed at temperatures above 200°C. Kinking was observed in specimens varying widely in initial orientation, scattering about a 45" angle between the slip plane and the specimen axis. The condition leading to kinking in tension appeared to be non-uniform distribution of flow along the gage length combined with the restraint imposed by the tensile load. At low temperatures and fast strain rates, the distribution of strain throughout the midsection of tension specimens was generally quite uniform; therefore, bend planes developed only near the ends as described by Miller.4 However, at high temperatures under creep conditions it was difficult to obtain specimens in which the distribution of flow was uniform. Some of the factors which may have caused differences in flow stress along the length of the crystals are: Nonuniform distribution of impurities, accidents of growth (lineage structure), slight bending or other damage during handling, surface conditions, and strain-aging characteristics due to dissolved nitrogen." Plastic flow, once started in a local region, often continued to a relatively large strain before other parts of the gage length became active. Under these conditions a series of kinks, such as those in Fig. 1, were produced. Fig. 2 illustrates how a nonuniform distribution of slip produces bending moments which- are responsible for kink formation. If no plastic bending were to occur while the rod extended by pure slip in two separate sections of the rod, it would assume a shape such as that in Fig. 2a. A specimen having this shape and being subjected to a tension load would have concentrations of stress at the concave surfaces C and lower than average stress would exist at the convex surfaces D. Therefore a bending moment is superimposed on the average stress in the regions between C and D. The positions of potential bend planes under these conditions are shown as dotted lines. Actually no such shape as Fig. 2a develops because plastic bending in the region C-D occurs simultaneously with pure slip in the intervening regions. The observed structure of a tension kink is indicated by Fig. 2b. Perhaps the best approach to an understanding of kinking as well as other related plastic bending phenomena, such as the bend planes discussed by Miller,' cell formation studied by Wood et al.,6 and polygonization,7 is consideration of the dislocation model of a bent lattice. Current theories of the slip process postulate generation or multiplication of dislocations at certain lattice imperfections. The mechanism proposed by Frank and Read8 results in continuous generation of concentric dislocation loops which spread out

Jan 1, 1953

By Willard P. Ward

HAVING been engaged during the past year in the manufacture of ferro-manganese in a blast furnace, I have imagined that some further information on this subject might be of interest to that large number of members of the Institute who are engaged in the iron and steel industries. The great question of the economical production of good steel, ingot metal, or homogeneous iron (we scarcely know now what to call it) from good materials, and at reasonable prices, has, thanks to the intelligence and energy of a few American engineers, been successfully solved in this country. Nearly all first-class railroads, and many that would riot rank so high, have adopted the Bessemer rail. Martin boiler-plates are rapidly gaining ground, in competition with

Jan 1, 1877

By Wilson T. Lundy

The history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur CO. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico. Terrain Characteristic of the delta region, the terrain consists of a low, flat, uninhabited area of marsh land intersected by many shallow lakes and bayous. With the exception of salt grasses, the region is devoid of vegetation and presents, in all directions, an unobstructed path to the vagaries of the winds. The general character of this area can be best visualized from the mechanism of its formation.' Offshore bars formed enclosing long narrow lagoons between the bar and the inner shore line, the lagoons communicating with the sea by means of tidal inlets. The water in the lagoons, being comparatively quiet, favored the deposition of fine debris composed of sand carried into the lagoons by action of the waves, tides and river-borne sediments from the land surface. As this material accumulated the bottoms of the lagoons were built up and eventually salt grasses obtained a foothold. The successions of growth and decay of these grasses formed a brown fibrous mat varying in depth from a few inches to several feet. This mat of vegetation virtually floats on an ooze that is several feet thick and is composed of alluvial sediments and very fine sand, and the whole is underlain by an unctuous clay. The decayed vegetation from the upper layer when dried has a peaty appearance.

Jan 1, 1934

By AIME AIME

FOR the development of a mine, a shaft of small cross-section is usually sunk, of no larger size than is absolutely necessary. After the mine has been developed and put on a production basis it is a common practice to sink a shaft of larger cross-section for hoisting and use the original shaft for the handling of men and material into the mine. While that ar¬rangement is usually expedient, the small size of the supply cages presents a problem in the handling of ma¬terial. Where a cage is, say, 4 by 4 ft., which is not an uncommon size, all lengthy and bulky material must be handled piece by piece several times from the supply department to the underground stations. Thus drill steel and timbers over 4 ft. long will be loaded on cars at the supply department and wheeled to the shaft, where each piece must be unloaded from the cars and stood up in the cage. They are then lowered to the shaft station, unloaded piece by piece and placed in cars, run to the supply station and again unloaded and stored until called for. In such a case handling becomes a major item in the cost of supplies.

Jan 1, 1930

By AIME AIME

THE initial meeting on Mining Methods* opened at 10 o'clock Monday morning with Scott Turner as chairman and W. Spencer Hutchinson as vice- chairman; about 60 attending. After preliminary announcements Theodore Marvin was called on for his paper,, entitled "Rock Tunnel Methods," which has been appearing serially in The Explosives Engineer. Marvin read the introduction and called attention to the account of one or' two particularly' interesting projects, such as the. Brooklyn water supply tunnel. E. D. 'Gardner, Char1e.s S. Hurter, L. D. Lamont and Spencer P. Howell took part in the discussion, Howell commenting on the fact that, in one case cited, misfires had occurred through detonator wires 'coming in contact with the case of an unapproved flashlight, .,: and that all flashlights should be approved.

Jan 1, 1931

By William Victor Vietti

A METHOD of determining the average density of the fluid column in a flowing oil well is presented. Actual field data from several wells are used to illustrate the application of the method in the Yates Field, Pecos County, Texas. The depth of the wells in the Yates Field varies from 900 to 1700 ft. depending on surface elevation and the location of the wells on structure. Production rates over 8000 bbl. hourly have been determined and many

Jan 1, 1930

By Robert L. Dean

THE pioneer mining company in Idaho to use airplanes extensively is the Yellow Pine project at Stibnite now owned by the Bradley interests. From 1901 to 1903 the gold boom at Thunder Mountain, in central Idaho overflowed to adjacent areas, prospectors discovering cinnabar and stibnite near the present site of Stibnite in Valley County. The workings were practically abandoned by 1911 through lack of capital and high costs of transportation on pack train roads over several mountain passes open only five months each year. During the World War there was some prospecting and production, and in 1921 twelve of the original companies were merged. Small-scale mining up to 1927 proved that an expenditure of several million dollars would be necessary to operate profitably. These properties were purchased by the Bradley interests during the period of 1927 to 1930. In 1927, there was no mining equipment except hand tools, no telephones, and only one building. Two mountain

Jan 1, 1935