Search Documents

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By Mungo Park, C. Baring Horwood

This paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes: (1) development-sampling and cornputatioll of ore-reserves; and, (2) stope-sampling and estimation of stope-values. Development-Sampling. It is with development-sampling only that this paper deals— the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estima-

Jan 1, 1909

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By T. L. Joseph

IT is a distinct privilege to participate in this meeting convened to honor the memory of Henry Marion Howe, a distinguished scientist and metallurgist. Many have added to our rapidly growing fund of metallurgical knowledge but few have made the unique contribution of formulating basic concepts essential to an over-all comprehensive view of the subject of metallography. Of those previously selected to deliver this lecture, several have added a personal touch to their discourse because they were able to refer to their associations with Dr. Howe. It was not my good fortune to know him or to enjoy his inspiring influence. Like most of you, my contact has been with his published works, which are outstanding in that they provide lucid, detailed expositions of the nature and behavior of metals and alloys. His deep understanding and clarity of expression have greatly accelerated our progress in metallography and in the use of metals. The degree to which a man's thinking, experimentation and writing contribute toward an understanding of basic laws and phenomena determines whether his life's work is of transitory or permanent value. This occasion appropriately recognizes the fundamental importance of Dr. Howe's pioneer work in the field of metallurgy. On two former occasions, gray iron was selected as a subject for discussion. The fact that the production of pig iron has not been discussed before does not reflect any lack of interest on the part of Dr. Howe or former lecturers in the process that under- lies the production of steel. Although Dr. Howe's work in his later years centered around metallography, his earlier publications show a considerable interest in the production of iron and steel. He recognized that in the ascending spiral of metallurgical advancement we are not winding a single thread but are weaving a complex fabric. Specific evidence of his interest in the production of pig iron may be found in his book1 on The Metallography of Cast Iron and Steel. In explaining why blast furnaces have been in constant use for about 600 years, he says: "The process is economical because it utilizes with extraordinary completeness the calorific power of the coke due to the thorough transfer of heat from the gaseous products of combustion to the charge." This emphasis on heat transfer, overlooked in many more extended and more recent discussions of the blast-furnace process, illustrates Professor Howe's ability to see the essentials. Other distinct advantages of the blast furnace, such as the removal of much of the sulphur and practically all of the oxygen, were mentioned. It was also stated that although the blast- furnace process is complex in nature, its outward form is comparatively simple, thus permitting large-scale production at small labor costs. All who contemplate the production of metallic iron from its ores by any other process might well consider the

Jan 1, 1946

By D. Geoffry Minnes, Ray Blair, Stanley J. LeFond

Nepheline syenite is a silica deficient crystal-line rock consisting of albite and microcline feldspars and nepheline, together with varying but small amounts of mafic silicates and other accessory minerals. Nepheline-bearing rocks are widely distributed around the world but only in Canada, Norway, the Union of Soviet Socialist Republics, and the United States are deposits worked commercially, Because of its low melting point and fluxing ability, nepheline syenite was investigated in the early 1900s by many students of glass and ceramics. Although the nepheline syenite deposits in Methuen Township, Ont., Canada, were discovered as early as 1897 it wasn't until 1935 that the first mill was erected to produce nepheline syenite products. In Canada, nepheline syenite deposits are worked by Indusmin Ltd. and International Minerals and Chemical Corp. (Canada) Ltd. who have combined production capacity in excess of 1800 stpd. Between 1935 and 1972 seven million tons valued at $78 million were produced from the Methuen Township deposits. In Norway, the Norsk Nefelin Div. of Elkem Spigerverket has produced nepheline syenite from a deposit on Stjernöy Island in western Finland since early 1960. Production has increased from 8 kt in 1961 to over 200 kt in 1980. Nepheline syenite has been under investigation in the Union of Soviet Socialist Republics (USSR) since at least 1928. In 1951 the first commercial alumina works was brought on stream at Volkhov, near Leningrad, utilizing nepheline concentrates from the Kola peninsula as mill feed. Since then two others have been completed and more are planned. Large quantities of portland cement, sodium carbonate, and potassium carbonate are produced in conjunction with the alumina. A material called nepheline syenite, but actually a pulaskite, is produced in Pulaski County, Arkansas, by the McGeorge Construction Co. for construction aggregates and by the 3M Co. for roofing granules. The Dome Fill Co. purchases the fines and uses them in the preparation of enclosed construction fill. Production is over 2,000,000 stpy. Chap. 16 on "Feldspar, Nepheline Syenite, and Aplite" in the 3rd ed. of Industrial Minerals and Rocks (Castle and Gillson, 1960) and Nepheline Syenite Deposits of Southern Ontario (Hewitt, 1960) contain excellent accounts of earlier commercial development of nepheline syenite as a glass and ceramic material. As in the 4th ed., this chapter deals mostly with the period since 1960 and with matters not previously reported in detail. An English monograph on Nepheline-Syenite and Phonolite (Allen et al., 1968) is a complete survey, at the time, of nepheline syenite which, with its very complete list of references, is an excellent source book. End Uses Nepheline syenite from the Canadian and Norwegian producers finds use primarily in the manufacture of glass and ceramics. One producer also makes several grades of nephellne syenite that are useful as extender pigments and fillers in paint, plastics, and rubber. In the Soviet Union nepheline is used in increasing quantities in the manufacture of alumina, alkali carbonates, and portland cement and to a lesser degree it is used in the manufacture of colored container glass.

Jan 1, 1983

By Arne Bergholm

Australian rutile was chlorinated in the presence of CO or carbon. The chlorination velocity in CO was found to be strongly influenced by temperature and proportional to the CO concentration, but independent of the Cl, concentration. In the presence of carbon, the reaction velocity is much higher. The reactivity of the carbon and the distance between the carbon and the rutile surfaces are important variables. The reaction velocity is approximately proportional to the Cl, concentration and independent of the CO concentration of the surrounding atmosphere. Experiments with fluidized-bed chlorination of carbon-rutile mixtures indicate that the motion of the bed has little influence on the reaction velocity. At low temperatures, the chlorination velocity of dense tablets is much greater than that of TiO, coke mixtures suitable for fluidization. The reaction mechanism is discussed. In the industrial production of TiCl, rutile is chlorinated in the presence of carbon. Disregarding intermediate steps, the reaction may be expressed by the following equations: The ultimate object of this study was to find out whether the reaction velocity was higher in fluidized bed operation compared with chlorination of pelle-tized carbon-rutile mixtures. From a literature survey and preliminary experiments it was learned that some basic knowledge about the reaction mechanism was needed for a good experimental design. Therefore the following sets of experiments were carried out: 1) Studies on the reaction velocity in the chlorination of rutile with CO as the only reducing agent. 2) Chlorination of separate rutile-carbon tablets. 3) Chlorination of rutile-carbon tablets at different temperatures with various kinds of carbon, various grain sizes, and various tablet-making techniques. This series of experiments was carried out not only with pure chlorine but also with mixtures of chlorine with argon, CO and CO,. 4) Chlorination of rutile-carbon tablets made in a strictly standardized manner. 5) Chlorination of static-bed rutile-carbon mixtures. 6) Fluidized-bed chlorination of the same mixture. The experiments 4 to 6 formed the final and direct test of the main question: Static bed vs fluidized bedo. Although there are many patents and papers dealing with the general aspects of chlorination, only few experiments from which detailed information can be obtained have been reported in the literature. Pamfilov and coworkersl3 have studied chlorination of TiO, with CO or carbon as the reducing agent. They found that the weight decrease per hour at 600o to 800°C amounted to 11 to 14 pct with CO and 45 to 51 pct with carbon. They suggest that phosgene might be an intermediate in the chlorination of TiO,. Takimoto and Hattori have chlorinated reduced titanium oxide (TiO) and found a very high rate of TiC1, -production. They proved that the composition of the gas from the chlorination of rutile-carbon mixtures contained mainly CO. They reported for instance 74.7 pct CO, and 5.6 pct CO at 800°C at which temperature the Boudouard equilibrium composition is 12 pct CO and 88 pct CO. Seligman and Segerchano6 have studied the chlorination of TiO. They proved that Ti0 and chlorine react rather rapidly at temperatures as low as 300°C. Above 400°C, the reaction was complete. At 500°C the velocity of this reaction was much higher than was chlorination of TiO, + C. McTaggart,7 Nishimura, et al. and Wilskam have chlorinated mixtures of carbon and various kinds of rutile or beneficated ilmenite. Nishimura, et al. also report the results from reduction of TiO, with H2, CO, or carbon. At 900°C only 1 pct Ti O is formed in 2 hrs. At 1100°C 23.1 pct Ti, 0, was formed if elementary carbon was present. No carbide formation occurred below 1400°C. McIntosh and Cofferll have observed that the CO, content of the exit gases from chlorination of rutile and calcined petroleum coke is appreciably higher than found in the Boudouard equilibrium. At 900°C the ratio (CO, /CO + CO) is about 80 pct, whereas the equilibrium value is about 2 pct. W. E. Dunn12 has studied the chlorination rates of several TiO,-bearing minerals with CO + Cl, or COCl . Chlorinations were carried out either in a fluidized reactor or a fixed-bed reactor, both having a 30-mm diameter. The results obtained in both reactors were comparable. It was proved that benefi-ciated ilmenite (i.e., ilmenite from which the iron oxide had been removed by chlorination) was chlorinated 10 times faster thanrutile. Sore1 slag showed an intermediate rate. When phosgene is used, the

Jan 1, 1962

By John V. Beall

There was optimism on 14th Street on April 22, Earth Day. We only have the report second hand because the demonstration conflicted with another appointment. Fifth Avenue was closed to vehicular traffic from 14th Street to the Park for a few hours and the crowd that showed up to promenade rivaled anything that can be imagined, even one at a country fair in Merry Old England. Certainly the domestic animals were there and the costumes were wild-as they are almost any day on 5th Avenue. However, the mood was friendly, happy and optimistic according to one of our neighbors who filmed and taped interviews with some of the characters. People think the air is going to be clean, and the water pure in the future. Land is going to be treated with respect. Even if the demonstration temporarily fouled the streets with litter, it served the purpose of dramatizing awareness. In talking to our friend about his experiences we didn't miss the opportunity to sound out his impression of whether or not people recognize that no group of people nor industry has a monopoly on pollution.

Jan 1, 1970

By Theodor Knutzen, Charles H. Fulton

The plant of the National Smelting Co., a corporation controlled by the Horseshoe Mining Co., was built during 1901 to smelt the dry siliceous ores of the northern Black Hills, extracting the gold- and silver-values in a matte of low copper-percentage which is shipped to Omaha and Denver for refining. Originally, the plant was designed to collect the values of the siliceous ores in an iron-matte, which mas to be resmelted with lead-ores, in a lead-furnace, the lead-bullion produced to be refined into Doré bullion in English cupelling-furnaces. However, the scarcity of lead-silver ores in the Black Hills, owing to the present non-productiveness of the Galena district, led to

Jan 1, 1905

By G. Carman Ridland

Front Range, Colorado: The majority of the rocks comprising the Front Range of Colorado are pre- Cambrian schists, gneisses, and intrusives which have been elevated to form part of the Southern Rocky Mountain physiographic province. The region is noted mainly for its production of gold and silver, but ores of tungsten, fluorspar, uranium, copper, and iron have been worked. Geological literature describes pitchblende and other radioactive minerals occurring at Jamestown, Boulder County; Central City, Gilpin County; and Lawson, Clear Creek County (fig. 1). These three adjoining counties cover most of the highly mineralized section of the Front Range which extends from James- town to Breckenridge. As far as the writer is aware, uranium has been found only in the portion north-east of Lawson.

Jan 1, 1950

By O. C. Wheeler

The activity in exploration and in the acquisition of prospective oil lands that reached such a high level in Colombia during 1936 gained momentum and reached unprecedented proportions during 1937. Both national and private lands were taken up. In the Magdalena Valley above Puerto Berrio, leases on large tracts of private lands are held by Richmond (Standard of California), Shell and Texas. Tropical also owns leases covering a block of acreage in this area near Honda. From Puerto Berrio to El Banco most of the acreage is of national ownership, and concessions covering parts of this area have been granted to Tropical, Socony Vacuum, Shell and others, while applications for additional concessions are pending. Latterly leases on private lands below the Lebrija River have been taken out by Shell and Richmond. In the drainage basins of the Meta and Guaviare Rivers of the Llanos region of eastern Colombia, several of the major companies have carried on geological exploration and it is understood that some private properties have been leased or optioned. Under Colombian law, subsoil rights are reserved to the nation on all lands that passed from Government ownership after Oct. 28, 1873. Private titles antedating that day carry both surface and subsurface rights. Conditions under which lands may be acquired, explored and

Jan 1, 1938

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants.

Jan 4, 1953

By Jonathan Ludlow, Paul J. Guay

Based on two studies that were funded by the U.S. Department of Energy, the authors provide an overview of the benefits expected from mining deeper webs on United States longwalls. The first study, completed in November 1979, identified the limits and potential gains from taking deeper webs with presently available equipment. The second on-going study discusses the conceptual design and benefits of a future system for taking very deep webs.

Jan 1, 1981

By R. B. Gavert, David J. Mack

ROOM- and elevated-temperature compression tests were made on the binary 3/2 electron compounds AuZn, CuAu, AgZn, AgMg, AuCd, and NiA1. These compounds possess either the B2 CsC1-type ordered structure or the A2 bee disordered structure represented commonly as ß and ß on equilibrium phase diagrams. In testing at room temperature, cylindrical specimens 0.508 cm by 0.330 cm diam were seated directly on an instron compression load cell (CF 0 to 10,000 lb). At elevated temperatures, testing included a special apparatus with a furnace heat source and a protective atmosphere.' The specimens were strained at a rate of 1 pet per min. The compounds were prepared from 99.99 pet or better high-purity elements. Vacuum and/or argon cover gas was used throughout the mixing, melting, and specimen drawing processes. The generally equi-axed specimen grains varied in size from 0.5 to 1.5 mm for the five different compounds. The stress-strain curves in compression showed

Jan 1, 1968

By Rudolf Gahl

Page Tests Conducted in Small Test Mill................... 577 Demonstration Tests Conducted by Minerals Separation Co....... 577 Flotation Tcsts Conducted by Inspiration Co............. 577 Sampling of Orebody........................ 578 Other Results Obtained in Small Test Mill.............. 580 Tests Conducted in Large Test Mill................... 580 Flow Sheet............................. 580 Discussion of the Value of Preliminary Table Treatment......582 Callow Flotation Installation..................... 585 Flinn-Towne ~nstallation...................... 587 Cole-Bergman Installation...................... 588 Methods Followed in Competitive Tests................ 590 Advantage of Pneumatic Flotation Machines.............. 591 Pneumatic Machines of Minerals Separation Co............. 591 Float Skimming Device......................; 594 Experimental Inspiration Flotation Machine.............. 596 Arrangement of Callow Cells in Series ................ 598 Variations of Flow Sheet....................... 599 Coal Tar as Flotation Agent..................... 600 Experience with Primary Slime.................... 602 Influence of Iron on Flotation..................... 605 Influence of Chemicals on Primary Slime............... 607 Fineness of Crushing Desired.................... 607 Operation of Large Concentrator..................... 608 Flow Sheet of Callow Sections.................... 608 Flow Sheet of Inspiration Sections.................• 609 Inspiration Flotation Machine of Steel Construction.......... 610 Minerals Separation Section..................... 613 Filter Plant............................ 613 Results Obtained in Commercial Concentrator............... 616 Tonnage............................... 616 Air and Power Consumption...................... 616 Floor Space............................ 617 Water Consumption......................... 617 Recovery............................. 618 Oil Consumption.......................... 618 Operating Costs for Flotation..................... 620 Discussion of Results Obtained.................... 620 Prospects for Futurc Development of the Flotation Process......... 621 Porous-Bottom Experiments..................... 622 Raising the Grade of Concentrates.................. 624 Recovering Carbonates by Flotation................. 624 Recovery of Silicates by Flotation.................. 627 General Theory......................... 628 Conclusion............................... 630

Jan 1, 1917

By V. Jares

DESPITE the fact that a combination of metals-aluminum-zinc-tin, and sometimes aluminium-zinc-cadmium-is extensively used for aluminum solders, as well as for die-castings, the constitution of these alloys has not yet been made clear. I. BINARY SYSTEMS The system aluminium-zinc is the basis of the ternary alloys under consideration. Their composition was made sufficiently clear by the investigations of Roscnhein and Archbutt,1 Bauer and Vogel,2 Sander .and Meissner,3 Hanson and Gayler4 and Isihara.5 Only the temperature of decomposition of the crystals s seems still to be doubtful, whether it is considered as a compound of Al2Zn3 (according to Bauer and Vogel) or as an intermediate phase of variant composition (according to Hanson and Gayler). This temperature is given by most of the authors, as in the neighborhood of 256° C., only Isihara giving 280° C. As its accurate determination is of special importance in the study of the ternary alloys under consideration it was experimentally controlled in the following manner: An alloy corresponding in composition to the formula Al2Zn3 was made, in which the temperature effect was found to be the greatest. This was drilled and a silver-constantan thermoelement inserted into the cavity so as to be in direct contact with the alloy. The whole was then very slowly heated and the heating and cooling curves determined. The transition temperature from the heating curve was found to be 281° C., whereas-from the cooling curve it was 252° C.

Jan 10, 1926

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1943

By Clintford R. Jones, Om P. Pande

This chapter presents a survey of instrumentation and control systems used on ball mill circuits from the past to the present. It is based on the concept of optimization of plant practice, and addresses the influence of the circuit design on the control strategy and on the instrumentation philosophy. Methods of optimization of the grinding circuit, within the constraints of the mill design requirements, are reviewed. The modern use of automation and circuit optimization is critically reviewed for known and possible conceptual control loops. A comparative study of circuit variations due to instrument hardware, location and installation is provided. Future trends i.e., computer control (DDC) and the effects on both the control stratagems and the optimization stratagems are described.

Jan 1, 1982

By W. L. Freyberger, H. Alter, K. L. Woodruff, E. L. Michaels

Laboratory and pilot scale tests have been made to determine the utility of heavymedia separation, particularly a cone-type separator, as a means of recovering aluminum and other values from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy-media system was determined. Two-stage pilot-scale heavy-media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses determined. The experimental results indicate that with certain reservations a heavy-media cone system can be utilized for aluminum separation and recovery from shredded and air-classified municipal solid waste. Observations made using two-stage heavy-media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1976