Search Documents

By Oswald J. Heinrich

(Read at the Philadelphia Meeting, February, 1878.) DURING the last twenty years much has been done to investigate and define the Mesozoic formation of the United States along the Atlantic States, as well as in the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geological surveys of Penn-

Jan 1, 1878

By William Marsh Baldwin

THE ROLLING OPERATION proper is applied to metals and alloys not only in the production of flat products but also in the production of shapes, rods, wire and even in specialized forms in the production of tubes. The present discussion of rolling copper and copper alloys will be [ ] limited to a consideration of rolling flat products such as strip, sheet, foil, plate, and others. In this case (as in the others listed above), the rolling operation itself is only part of an integrated sequence of operations. In Fig I such a sequence going to make up a brass strip mill is sketched out. It is seen that the rolling opera-

Jan 1, 1948

Jan 1, 1969

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952

By Reinhardt Thiessen

IN THE general study of coal, all evidence points in the one direction -that coals had their origin in a manner analogous to that of peat. The best method of studying coal, whether it concerns its chemistry, composition, or physical condition, is to study peat. The essentials in a study of peat are a knowledge of the chemistry of plants, knowledge of decay and of the transformation process of plant-substances into peat. A number of facts must be emphasized, namely, (1) peat is formed under wet conditions only; (2) plants grow in the place where peat is formed; (3) all the plant substances go into the bog; and (4) all the plant substances are subjected to a series of phases of decay which are (a) in the air completely above the water level but in relatively moist conditions; (b) above the water level, but covered by debris; and (c) completely submerged by both water and debris.

Jan 3, 1925

[NORTH AMERICA ALASKA Anchorage.-Strandberg, H. Chlchagoff.-Russell, J. C. College.-Barber. R. J. Dorsh, J. B. Fox, E. F. Joesting, H. R. McAnerney, J., M. Douglas.-Cahill, W. E. Fairbanks.-Beistline, E. H. Crawford, J. D. Earling, R. B. Greves, J. H. Harris, Q. P., Jr. Henton, H. M. Herbert, C. F. Hester. W. B. Hopkins, J. E. Kreitlow, E. J. MacDonald, D., III March, J. P. Mathews, T. C.]

Jan 1, 1940

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By George Sachs, S. M. Clark, George Espey

he tendency of a commercially drawn cartridge case to crack in the mercury test and the relation of cracking tendency to residual stress retained after drawing were studied. The fourth drawpiece (next to the final) of caliber 0.30 cartridge cases produced by Frankford Arsenal were selected as test pieces. These exhibited an exceptionally high cracking tendency, making a detailed study possible. To obtain fast cracking in the mercury test, about 0.0015 to 0.003 in. must be removed from the wall thickness of the drawpiece by pickling, and it must be subjected to the mercury test immediately after washing. Removal of the adhering mercury by annealing and subsequent squeezing of the case in a vise was used to reveal definitely the presence or absence of cracks. Various lots of apparently identically fabricated cases were shown to possess a different cracking tendency. Machining off or boring a hole in the base gradually reduced and eventually eliminated the cracking tendency. On the contrary, shortening of the wall (body) reduced the cracking tendency only if the wall became so short that the cracking zone was directly affected. By boring out the base and pickling from the outside and then splitting the resulting rings, it was possible to determine the approximate stress distribution in the base and in the adjacent part of the wall. Small compression stresses were present in the core and the major part of the base, while the surface of the base and the adjacent wall contained high circumferential tensile stresses. On the contrary, the wall when parted from the base contained only insignificant residual stress. The conception is advanced, that the stress distribution in a drawn cartridge case corresponds fundamentally to that of a tube (wall) shrunk on a disk (base). Such a stress distribution results from the tendency of the base to recover elastically by an increase in diameter from the biaxial compression during drawing while the wall exhibits little tendency to change its diameter after progressing through the die. This is confirmed by measurements which show the base diameter to be slightly larger than the wall diameter.

Jan 1, 1945

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

Philip Argall, Denver Col. (communication to the Secretary): Dr. Raymond claims (Trans., xxiii., 560)) that my statement (p. 557) regarding the crystallization of iron "is beyond question incorrect." He says: "It is not even settled that vibration will crystallize iron under any conditions." While admitting that authorities differ on the possibility of cold crystallization of iron, I believe it is a settled and undisputed fact that vibration in the presence of heat will crystallize iron. Bloxam and Huntington say :* " Vibration assists 'in converting fibrous metal (iron) back into a crystalline state when heated, a lower temperature sufficing than in the absence of vibration." Mr. A. F. Hill, summing up a very exhaustive review upon the crystallization of iron and steel, pronounces against crystallization, but only at temperatures below 900' F. Mr. Howe, discussing ,the breakage of a 20-foot porter-bar with a crystalline fracture, suggests that it was attributable to heat, jointly with the jar. We see, then, that vibration of heated iron bars will induce crystallization and consequent change of structure. Referring to my statement, I wish to point out, that I was discussing the vibration of stamps arid should have said, "vibration under all such conditions," etc. That is, vibration attended with sharp blows, such as a stamp-stem is subjected to, will crystallize iron; yet I believe that intense vibration under any condition will

Jan 1, 1895

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show's graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By Thomas Wilson

IN a single-crystal cube of iron the arrangement of the atoms is that characteristic of iron at room temperature: the body-centered cubic lattice. X-ray investigation has shown this structure to be characteristic of iron, as it has shown the atomic arrangement of other metals to be characteristic of those metals also. Rarely do substances have more than one characteristic atomic arrangement. Many physical properties of metals are directly connected with their atomic arrangements, so that changes of arrangements produce changes of properties. Only chemical change influences atomic arrangement. If a difference in the physical properties of a metal is caused by a process which involves no chemical change, the cause of the difference in properties must be sought elsewhere than in the atomic arrangement. Frequently this cause can be traced to alteration of crystal orientation. The orientation of a crystal may be defined as the relationship which the crystallographic axes bear to some quantity of reference. A cube of iron appears cubic whether it is regarded from a face, an edge, or a corner. Yet these three positions represent three different orientations of the cube with respect to the observer. It is evident that the orientation of this cube of iron, unlike the atomic arrangement, is not characteristic of iron but is entirely dependent on the previous history of the cube. Most of the processes of metal working, such as wire-drawing, rolling, and bending, change the orientation of the crystals present in the worked metals. These processes usually tend to produce rotation of the crystals into positions approaching a mean. Specimens of metals show-ing this characteristic are said to possess a preferred, orientation. Tensile strength, ductility, and many other properties are influenced by orientation changes; therefore two specimens of the same metal may show different values of these quantities. In metal specimens possessing a narrowly limited preferred orientation, these quantities will vary in magnitude in different directions throughout the specimens. The investigation of the influence of manufacturing operations upon crystal orientation, and hence upon physical properties of metals, is an important

Jan 1, 1929

By Charles R. Keyes

I. Introductory,.......... 185 II. Hypotheses oF the Origin of OzaRk Ores..... 186 1. General Considerations........ 186 2. Schmidt-Leonhard and Gage View...... 187 3. Jenney Opinion.......... 187 4. Posepny Idea,.......... 188 5. Winslow-Robertson Hypothesis....... 188 6. Branner Proposition......... 189 7. Keyes Statement.......... 189 8. Van Hise-Bain Theory........ 190 III. Requirements of an Adequate WoRking-Hypothesis,... 190 IV. GeneRal Geotectonics of the OzaRk Region.... 192 1. Salient Aspects.......... 192 2. Geologic Formations......... 192 3. Character of Faulting...192 4. Extent of Flexing......... 193 5. Unconformity Inequalities....195 6. Warping of Strata...195 V. Classes of Ore-Deposits... 196 VI. Vadose ORe-ConcentRation,........ 197 VII. GeogRaphic DistRibution of the Ore-Bodies,... 199 VIII. Relation of ORe-Deposit to Geologic Structure... 201 1. General Occurrence of Ore-Bodies in Basins.... 201 2. Deposits of the Central Missouri District..... 203 3. Deposits of the Southwestern Missouri District.... 203 4. Deposits of the Northern Arkansas District... 305 5. Deposits of the Southeastern Missouri District.... 206 6. Synclinal Ore-Deposits of Other Districts.....207 7. Significance of Ore-Troughs in Prospecting... 209 8. Origin of the so-called Synclines,...210 9. Significance of the Cross-Bars of Joplin..... 213 10. Relation of Ore-Run to Ancient Relief-Features,... 215 IX. Direction of GRound-Water Circulation..... 216 X. VeRtical Range of Workable Ore-Bodies,... 218 XI. Oscillation of Ground-WateR Level...... 219 XII. Relations of Ore-Bodies to Lithoclasic Features,.. 220 XIII. PRimaRy Source of Ore-Materials,...... 220 XIV. Zone of Ore-Enrichment,......... 222

Jan 1, 1910

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By M. Baeyertz

SINCE 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer1, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallography. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types.

Jan 1, 1930

By J. V. Emmons

It has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass.

Jan 1, 1915

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By Charles B. Dudley

DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails end their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? Yon will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to Crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light

Jan 1, 1881

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O'Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961

By Robert Lewis

THE Utah coal field to which the name Book Cliffs is applied runs in a northeast direction from Mt. Hilgarde, in Sevier county, along the escarpment of the Wasatch Plateau to the vicinity of Castle Gate, thence southeast along the Book cliffs, which lie to the north of and generally within sight of the Denver & Rio Grande Railroad,. to the Colorado line. The Book cliffs form the southern escarpment of the West and East Travaputs Plateaus, and vary in height from 2,000 to 6,000 ft. At the base of the Wasatch and Book Cliffs escarpments is a broad plain known as Castle valley. The coal beds outcropping in the escarpments along this valley are worked on the largest scale of any in the State, and this particular area is known locally as the Castle Valley coal field. Geology The Book cliffs are capped by the Tertiary-Eocene-formation, consisting of varicolored shales; buff sandstone, conglomerate, and subordinate thin beds of limestone. Different sections show diverse stratigraphy. This is mainly the Wasatch formation, and lies unconformably upon the rocks of the Upper Cretaceous. Fig. 1 is a generalized section of the rocks of the. Book Cliffs field. The Mesaverde formation contains the cliff-making rocks of the Book cliffs, and is composed of massive sandstone interbedded with sandy shales and beds of coal and carbonaceous shale. The sandstone has greater resistance to erosion and the formation is characterized by escarpment ledges and cliffs. The shale is commonly sandy and is drab in color, but where it is associated with the coal it is usually carbonaceous. The sandstone is generally buff, though occasionally it is white, and in places red. The bedding ranges from thin to massive. In the lower part. of the formation the sandstone is red in

Jan 7, 1914