Search Documents

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By L. G. Evans, C. Rampacek, G. A. Freeman

A large aggregate tonnage of oxidized and mixed oxide-sulfide copper ore of the southwestern U.S. is not amenable to conventional flotation concentration or sulfuric acid leach treatment. Most of the ores contain chrysocolla as the principal oxide copper mineral, for which no successful commercial flotation method has yet been developed. Acid leaching some ores is not feasible since they contain substantial quantities of calcite and other acid-consuming constituents. Other ores decrepitate during leaching or contain excessive slime and clay minerals which cause plugging of the ore beds.

Jan 10, 1961

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

By F. M. Lyon, F. J. Chernosky

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By David S. Cahn

Pilot-plant and laboratory tests were made on blends of steel plant flue dust and portland cement to determine whether the flue dust could be pelletized for use as a source of iron in dry process cement manufacture. Strength and setting time results showed that an acceptable agglomerate can be made with a Type II portland cement binder. Abrasion-resistant and well-sized pellets were made in a horizontal drum, using a simulated closed circuit, with a binder content of 7.5% and a moisture content below 15%. Pellet quality was found to be relatively insensitive to changes in binder concentration above 5%. Simulations of stockpiling and weathering indicate that little difficulty would be encountered with use of the flue dust pellets in cement plants.

Jan 1, 1972

By J. R. Cooper, A. Bruynesteyn

The final results of the operation of the Cananea test dumps are discussed. Scale-up factors between shake-flask tests, column tests and the large test dumps are established for the Cananea ore. The formation of clay layers, which formed inside the dumps and markedly affected extraction, as well as secondary enrichment, are discussed.

Jan 1, 1974

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now hen changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical

Jan 1, 1932

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for: agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar" method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will' be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By Walter B. Devereux

Metallic copper is a product of native metallurgy in various parts of Mexico, and by somewhat varied processes. While recently examining copper mines in the State of Jalisko, I had an opportunity of witnessing Mexican copper smelting by a process which I have not seen described, and which is interesting from the fact, that a fine quality of copper is produced from sulphurous ores in three metallurgical operations, and apparently without excessive loss. The process was carried on in buildings which were part of a plant erected by an American more than twenty-five years ago for the purpose of smelting and working copper. After a few years this man met with accidental death, and the works have been but little used since. Located in the centre of a high range of mountains, far from any town or seaport, and inaccessible except over difficult mule trails, these substantial buildings, filled with furnaces and heavy machinery,

Jan 1, 1883

By S. R. Gilbert, B. W. Burdett, L. B. Hales

A brief review of grinding control systems is given with a review of the most popularly reported control loops. The trend toward more sophisticated control systems in terms of control strategies and control equipment is discussed, and the reasons for the popularity of distributed control equipment are outlined. The evolution of the interface between the operator and the process and its importance in plant control is described. Finally, the authors' view is given as to the future of grinding control.

Jan 1, 1984

By Arthur Smith

THE Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district-the United Verde and the United Verde Extension-lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., . a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to? the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Wood chute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the . smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the vicinity of Allen Springs, at the south end of Mingus mountain and all within the boundaries of the Prescott national forest reserve.

Jan 3, 1924

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By D. C. Bard

THESE notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Butte Sulphide Vein. Matter. Per Cent. Oxygen 43.00-Quartz, rhodonite, rhodochrosite, barite, calcite, and hübnerite. Silicon 36.00-Quartz, rhodonite, and willemite (very rare). Sulphur 5.00-Sulphides of. iron, zinc, copper, lead,. and sulphates of barium and rarely calcium. Iron 5.00-Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese, . . . . 2.00-Rhodonite, rhodochrosite, and hübnerite. Zinc, . . . . 1.00-Spha erite, very rare wurtzite and willemite, and tetrahedrite and tennantite.

Jan 8, 1913

By Charles F. Brush

THE compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

Jan 1, 1876

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

By Charles F. Brush

The compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

By Thomas E. Ban, Charles D. Thompson, Charles A. Czako

Continuous sintering-a metallurgical process for more than 50 years-has broadened from its origin in nonferrous metallurgy to present-day applications in ferrous, chemical, and nonmetallic fields. During the past year, self-fluxing sinter production has been a subject of active interest to iron metallurgists in North America. Accomplishments however, have come predominantly from Europe and proper interpretation of these reports requires an understanding of European raw materials and European economics. The technology, of course, can be applied universally.

Jan 10, 1959

The annual report f the Secretary of the Navy for the fiscal year, ending June 30, 1917, but including operations and recommendations up to Dec. 1 of that year, contains the following remark about the activities of the Naval Consulting Board. The members of the Institute who are members f this Board are William L. Saunders, Benjamin B. Thayer, Thomas A. Edison, Thomas Robins, Lawrence Addicks, Joseph W. Richards, W. R. Whitney, assisted by 47 other members f the Institute, in the capacity of associate members of the Naval Consulting Board. During the year, the work of this board, organized and approved by Congress in 1915, has increased very materially in importance and volume, its meetings have been frequent and the work of its individual members has been such in some cases as to occupy almost their entire time in the service of the Government. Some time before the active entry of this country into war the board called a special meeting to which were invited some 50 of the leading scientists and industrial managers, whose special study fitted them to advise on the methods of meeting the

Jan 2, 1918

By Stuart S. Forbes

Changes and additions made to the Canadian Copper Refiners Ltd. electrolytic refinery between 1949 and 1955 are reviewed. The effect of high current density on current efficiency and section work is discussed. OPERATING and physical changes which have been made to the electrolytic tank house of Canadian Copper Refiners Ltd. suggest a review of present conditions. Previous papers1 a have described the general arrangement. Since then, expansion, closer anode spacing, and higher current densities have increased annual cathode capacity from 112,000 to 182,000 tons. A recent extension to the tank house, begun in the spring of 1954 and completed in August 1955, was undertaken to handle the monthly production of about 3,000 tons of anodes from Gasp6 Copper Mines. The anticipation of these additional receipts and large stocks of unrefined copper caused by the increase in custom smelting at Noranda made it necessary to increase production without immediately available additional cell capacity. Accordingly, from December 1954 through March 1955, the tank house was operated successfully at a current density of 24.0 amp per sq ft. Again, as of September 1955, one of the two tank house circuits is being operated at this high density. Although other refineries may operate at current densities higher than 24 amp per sq ft, none is doing so with anodes which contain silver and gold content as high as those being refined at Canadian Copper Refiners Ltd. General Arrangement The original building consisted of two parallel bays, each 660 ft long and 60 ft wide, with a 24 ft pump bay extending along the west side of the building. A previous expansion, completed in 1939, was to the west of the original building and consisted of two 60 ft parallel bays 240 ft long. The length of these two bays was extended in 1954 to 540 ft, adding one stripper and 12 commercial sections to No. 2 electrical circuit. Space is still available for an additional six commercial sections and one stripper section. Construction on these seven sections started in September 1955, and will be completed early in 1956. The tank house capacity will then be 206,000 tons of cathodes per year. In the two tank houses there is a total of 900 cells distributed as follows—commercial, 468; stripper, 36; total, 504 in the No. 1 tank house (No. 1 circuit): commercial, 360; stripper, 36; total, 396 in the No. 2 tank house (No. 2 circuit). Section arrangement consists of nine cells to a tier and two tiers or 18 cells to a section. Anodes, weighing 620 lb each, are cast with a Baltimore groove and are refined by the multiple system. Solution enters each cell through a bottom inlet at one end and overflows at the top of the opposite end. Rate of solution flow through the cells is controlled by valves at each section to 4.5 gpm. Electrical power to the tank house is now provided by nine 675 kw motor generator sets. Each set consists of a 135-12 v 5000 amp dc generator, driven by a 980 hp 2300 v synchronous motor. When No. 1 circuit is operated at 22,000 amp, five sets, at 4400 amp each, are connected in parallel. As the maximum allowable current on No. 2 electrical circuit has recently been set at 18,000 amp, only four sets are connected in parallel on No. 2 circuit. A tenth set, now being installed, will be reserved as a spare, for use in either circuit as required. Recent Changes In 1949, the annual capacity of the tank house was increased from 112,000 to 132,000 tons by closing the

Jan 1, 1957

By W. A. Hustrulid, N. A. Ross

An analysis of the design of medium to hard rock tunneling machines is presented. The developed equations are used to compare performances and machine requirements using kerf and fixed pick cutters to bore a given rock. With the use of pick cutters, required thrusts can be greatly reduced and still achieve the same boring rate as with present day tooth or kerf cutters. It appears that the cutting coefficient, which for most boring machines is of the order of 0.1, should be increased to one or larger to facilitate rock removal by cutting rather than grinding. The depth of cut and the indexing distance should be greatly increased to make use of inherent rock weakness.

Jan 1, 1971