Search Documents

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By W. T. Cardwell, R. L. Parsons

This paper discusses the practical problem of estimating a single equivalent permeability for an oil reservoir, or a portion thereof, whose actual permeability varies in an irregular manner. Limiting averages for general types of permeability variation are developed, and illustrated by examples involving important, specific types of variation. Introduction The theory of the flow of fluids through porous media1"4 is becoming increasingly important in predictions of oil-reservoir behavior. In practical applications, however, reservoirs are seldom found to which simple theory strictly applies. Actual reservoirs have complicated shapes and nonuniform permeabilities and porosities. This paper discusses the problem of estimating a single equivalent permeability for an oil reservoir, or a segment of an oil reservoir, whose actual permeability varies in an irregular manner. The equivalent permeability of a reservoir segment is defined as the permeability of a homogeneous segment of the same dimensions that would pass the same flux under the same pressure drop- It is the permeability value that can be used in simple theoretical formulas to calculate the reservoir behavior. To the authors' knowledge, previous theoretical calculationst on systems of nonuniform permeability have been carried out only by Muskat'"; and he has not dealt with irregular variations, except in writing down the general differential equation for the pressure in variably permeable systems.lb In practical work, many calculations necessarily have been made to estimate equivalent permeabilities from the permeabiiity profiles obtained by core analyses. Regarding such calculations, Johnston and Sherborne6 say: Simple arithmetic and weighted averages have been tried on many wells and it has been found that, where frequent sampling has occurred, the arithmetic average is as satis- factory as a weighted average. It is possible that the application of statistical methods to the analysis of permeability data as recently presented by Law8 may prove fruitful. L,, has made a valuable contribution in showing how statistical analyses may aid in picturing the characteristics of a reservoir from those of a necessarily limited number of core samples. It is believed however that the particular problem of the estimation of equivalent permeabilities can be most directly approached from a fluid dynamical viewpoint as given in the present paper. An example is presented of the use of the conclusions herein in conjunction with Law's method. Theory In order to approach the problem of heterogeneity simply, it is interesting to consider a square block composed of four smaller, homogeneous, square blocks of porous medium, two of which have a

Jan 1, 1945

By D. M. Kehn

A method has been devloped for chromatographic analysis Of the vapor and liquid phases Of a a system containing methane to components having 20 or more carbon atoms. The method uses a windowed equilibrium cell in which volumetric phase behavior of the system can be observed accurately and from which small samples of gas or liquid can be withdrawn for analysis. Analyses are made using two chromatographs, one for the lighter and one for the heavier components in a sample. Combination of the two analyses yields a detailed analysis of the gas or liquid sample. The complexity of the condensate heavy ends is evident from the chromatograms of these fractions, and the predominance of the paraffin hydrocarborn serves as a useful marker in interpreting the chromatograms. The K-values obtained in this analytical method are presented for a high-pressure condensate system and predict closely the observed volumetric behavior of the system. INTRODUCTION Quantitative analysis of hydrocarbons from natural gas reservoirs is necessary for several reasons—to calculate the amount of sales gas produced, to calculate the amount of natural gasoline produced, to plan a liquid recovery system, or to calculate the potential economic value of a reservoir produced under one or more of several different conditions. Analysis of natural gas fluids produced to the surface consists of identifying and computing the mol fraction of each component of the mixture. Although methane is the predominant component, varying amounts of ethane, propane, butane, pentanes and heavier components are also present. Materials containing up to 30 carbon atoms occur in amounts which decrease with increasing molecular weight. However, the quantities of components in the 20 to 30 carbon atom range are usually so small that their importance is negligible, and they are undetect-able in natural gas by ordinary analytical methods. All the components up to those having 20 carbon atoms may sigsficantly affect phase behavior, however. Commonly, only the methane-through-pentane fraction is analyzed quantitatively for each component, while components heavier than Pentane are lumped and repored as "hexane- plus". Expensive, tedious techniques are required for analysis of this fraction. Consequently the detailed analyses needed for prediction of reservoir behavior are usually undertaken only when major gas fields are being developed. The need for complete analyses of condensate systems is apparent when it is recalled that most gas fields are produced by pressure depletion. As the pressure declines, some of the heavier hydrocarbons are lost as liquids which are in the reservoir. In many instances the amount of liquid in equilibrium with the gas phase at high pressure constitutes only 1 or 2 mol per cent of the total system. Flash calculations generally must predict the actual amount of liquid with an accuracy of a few per cent in order to be useful. This retrograde condensation has been understood for years, but accurate correlation methods to permit quantitative prediction of phase behavior in the retrograde region are not presently available. The increasing importance of natural gas has made accurate prediction of phase behavior and composition of produced natural gas streams an economic necessity. The work reported here was undertaken to provide a rapid, economical method for obtaining the vapor-liquid equilibrium information needed to predict accurately the composition of the fluids produced from a gas reservoir throughout its life. TO develop this method, a pressure cell equipped with windows was designed and built for observing the volumes of liquid and gas present at reservoir pressures and temperatures. Use was made of established chromatographic methods for rapid and detailed analysis of both phases. This paper describes the equipment and techniques developed for obtaining vapor-liquid equilibrium data, presents the results of analyses of a condensate system, and indicates the usefulness of these data in predicting hydrocarbon phase behavior. DESCRIPTION OF EQUIPMENT USED The equipment used in obtaining the required information on phase behavior and the complete analysis of hydrocarbon mixtures through C, will be described first, followed by a discussion of the operation of the equipment. It will be helpful, however, to consider first a brief outline of the technique used. A sample of separator gas and liquid is charged to the windowed cell (see Figs. 1 and 2) where volumetric equilibrium phase behavior at reservoir pressures and temperatures can be determined. Then samples of the coexisting phases are withdrawn. The methane-through-pentane fraction is analyzed with a chromatograph equipped with a hot-wire detector, and the pentane-plus fraction is analyzed with a second chromatograph equipped

Jan 1, 1965

By A. J. McEvily, R. C. Boettner, C. Laird

The processes leading to fatigue failure in the low-cycle range were studied to obtain an understanding of the basis of Coffin's law. Particular attention was paid to the manner of mack nucleation and to the determination of the portion of the total lifetime spent in crack propagation. It was observed that cracks are nucleated at surface notches meated during reversed plastic deformation, Principally at grain boundaries, and that crack growth occupies greater than 75 pct of the fatigue life. When inclusions are present, they are often the primary sites of crack initiation. From consideration of the incremental distances advanced by a crack in each cycle and of the lifetimes of different materials, it appears that the universality of Coffin's law arises from the similarity of crack-tip strain for a given applied strain amplitude, irrespecti7:e of material. STUDIES of low-cycle fatigue have been particularly rewarding in that a simple correlation between fatigue lifetime and plastic-strain range has been shown to exist. This empirical relationship takes the forml,2 Nner=C [1] where N is the number of cycles to failure, Er is the plastic-strain range defined as the total plastic strain per cycle (the sum of the tensile plastic strain plus the compressive plastic strain), n, the exponent, is a constant independent of the material to a first-order approximation and often has a value of about 0.5, and C is a constant which for a number of ductile and metallurgically stable materials is approximately 0.65 for fully reversed strain.3 This relationship has been shown to be valid for a wide variety of metals and alloys and is often referred to as Coffin's law. However, it is yet not clear why so many different metals and alloys exhibit the same over-all behavior in the low-cycle range. Less is known about the mechanisms of fatigue failure in the low-cycle range than in the high-cycle range, but it is expected that the processes would have much in common. For example, an important characteristic common to both high-and low-cycle ranges is that fatigue crack propagation can occupy a considerable portion of the total lifetime. This has been shown by Laird and smith4 by a count of the number of ripples present on the fracture surface of copper specimens, each ripple corresponding to one cycle of load. On the other hand, some marked differences have been noted. For example, in copper,5 nickel, and aluminum4 there is a greater tendency for grain boundary cracking to occur as the strain amplitude is increased. The purpose of the present work was to study further the processes leading to fatigue failure in the low-cycle range and to obtain an understanding of the basis for the validity of Coffin's law. Particular attention has been paid to the manner of crack initiation and to the determination of the portion of total lifetime spent in crack propagation. MATERIALS A number of metals and alloys were tested, although more attention was focused on a particular few, once general trends had become apparent. Alloys were selected so as to investigate the effects of crystal structure, number of phases, stacking-fault energy, and impurity content. The materials in this grouping were: high-purity copper OFHC copper 1100 aluminum (commercially pure) 70-30 brass (Cu-30 wt pct Zn)

Jan 1, 1965

By Tell Ertl, Ernest E. Burgh

INTRODUCTION THE Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose-that of finding out how to mine oil shale most cheaply-entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, factors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing. When the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. PROCEDURE Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 1 ¼ in. in diameter was used in 6, 12, and 18 ft lengths with 2 1/8 -in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton. During the experiments air pressure varied between 75 and 90 psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings To facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-steel sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a 1-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1947

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By J. P. Morris

PREVIOUS investigations1,2 have shown that alloying elements in liquid iron influence the thermodynamic activity of sulphur and thereby affect the partition of sulphur between metal and slag in the desulphurization process. For example, the greater efficiency of desulphurization in the blast furnace as compared to the open hearth can be attributed in part to a higher level of sulphur activity in blast-furnace metal due to the higher concentration of carbon and silicon. In the present investigation, a short study was made of the influence of manganese on the activity of sulphur in liquid iron and iron-carbon alloys. In contrast to carbon and silicon, manganese was found to decrease the activity coefficient of sulphur; and in iron-carbon alloys it counteracts to some extent the influence of carbon. However, at manganese concentrations normally present in the blast furnace or open hearth, the effect of manganese is small. Since manganese sulphide has a limited solubility in iron, manganese can act, under certain conditions as a desulphurizing agent. Considerable data on the manganese-sulphur product in carbon-saturated melts were obtained in the investigation and have been included in this report. The experimental procedure was the same as that used in the earlier investigations on the effect of silicon' and carbon' on sulphur activity. Briefly, the method was as follows: The molten alloy, contained in a graphite or sintered alumina crucible, was brought to equilibrium at a constant temperature with a mixture of hydrogen and hydrogen sulphide of constant composition by bubbling the gas through the metal. Samples of' the melt were taken for analysis at regular intervals by suction through a 2 to 3 mm bore silica tube dipped into the metal. The experiments were run in a graphite spiral resistance furnace with melts weighing 50 to 60 g. The gas bubbling tubes were made of sintered alumina and were 5/16 in. OD, 1/16 in. ID, and 24 in. long. Equilibrium was assumed to have been attained when the sulphur content of the liquid metal reached a constant value. During an experiment there was a rapid loss of manganese from the melt by volatilization. To offset this loss, small additions of manganese were made periodically. The rate of manganese addition needed to maintain a constant manganese concentration was determined in preliminary tests. In all of the experiments, deposits of manganese sulphide formed above the melts in a cooler region of the furnace. Apparently, these deposits resulted from a reaction between manganese vapor and hydrogen sulphide in the gas. To prove that manganese sulphide did not volatilize from the melts to a measurable extent, an experiment was run in which helium was bubbled through liquid iron containing both manganese and sulphur. Although manganese volatilized rapidly in this test, there was no appreciable loss of sulphur. Volatilization of manganese sulphide from a melt would have led to an apparent equilibrium condition in which the sulphur content of the metal was lower than the true equilibrium value. The experimental results are shown in the first seven columns of Table I. The data in the last two columns were obtained from the previous work on the effect of carbon' and show what the results would have been in the absence of manganese but with temperature, gas composition, and carbon content of the metal remaining the same. Comparison of the last four columns show that, in the presence of manganese, the sulphur content of the metal increased at equilibrium and the activity coefficient of sulphur decreased. However, the results show that, for manganese concentrations below 3 pct, the effect of manganese is small. The values for activity coefficient of sulphur given in Table I were calculated from the following relations: S (in liquid metal) + H2 (gas) = H2S (gas) [l] K ph2s/?s X %S X phg = 0.00251 [2] where K is the equilibrium constant for the reaction, PH2S and ph2 are the partial pressures of hydrogen sulphide and hydrogen, respectively, and ?s is the activity coefficient of sulphur. The standard state for sulphur was taken to be a 1 pct solution of sulphur in pure iron. The numerical value for K at 1600°C was determined in the earlier work. For the purpose of showing graphically the results of the tests run at 1600°C, the activity coefficients of sulphur were recalculated so as to correspond to a manganese concentration in the metal of 2 pct in each case. In the calculation it was assumed that the increase in sulphur content of the metal at equilibrium caused by the presence of manganese

Jan 1, 1953

By S. E. Bronisz, Dana L. Douglass

a Uranium was deformed by cold rolling, and the effects of this plustic deformation on the microstruc-ture of the metal were observed by the technique of transmission elecbon microscopy. The recrystalli-zation of selected cold-wmked samples was also studied by this method. The samples were prepared for examination by electrolytic thinning in a standard metallographic electrolyte which has not been previously reported as being used in producing thin foils of uranium. The microstructural changes observed in the a uranium were generally similar to those seen by optical microscopy. The changes in the microstructure of a uranium following cold work and recrystallization treatments have been the subjects of several studies employing optical and X-ray techniques.12-19 These studies indicated that twinning was the redominant mode of deformation at room temperature20 and that the regions of high energy associated with the deformation twins were preferred sites for the initiation of recrystallization.15,18, Recently several workers have prepared thin foils of uranium suitable for examination by transmission electron microscopy.'-lo The foils thus prepared have been used to study fission fragment damage; a particular dislocation reaction,' and gas precipitation." At this laboratory the microstructural changes occurring during the cold working and recrystallizing of a uranium samples have been studied by using transmission electron-microscopy techniques. The foils used in this work were electrolytically thinned in a polishing bath not reported previously in the literature as being used for this purpose. EXPERIMENTAL PROCEDURE The uranium used in this investigation was depleted a uranium sheet 4 mils thick. The results of a spectrochemical analysis of this material are shown in Table I. The as-received uranium was cut into strips, 1 in. wide by 5 in. long, and annealed in vacuo at 600°C for 2-1/2 hr. The resulting microstructure consisted of relatively uniform, equiaxed grains having diameters of 10 to 50 p. Cold Working. The cold-worked samples were prepared by rolling several of the annealed uranium strips to various thicknesses. The strips were reduced 3.5 ± 0.5, 6.0 ± 0.6, 10.0 ± 0.5, 19.5 ± 1.0, and 28.5 ± 2.0 pct in thickness. It was not possible to achieve these reductions with a single pass through the rolling mill, so the strips were turned end for end during the rolling procedure. The cold-rolled strips were stored in dry ice until samples from them could be thinned and examined (within 24 hr after rolling). Annealing. The samples used in studying the re-crystallization behavior of a uranium were obtained by annealing sections of the strips which had been reduced 10.0 and 28.5 pct. These samples were sealed in evacuated Pyrex capsules and were annealed in a tube furnace at temperatures from 200" to 600°C and for times from 1/2 to 2 hr, see Table l. Thinning: The samples from the rolling and heat treatments were prepared for examination in the electron microscope by electropolishing in a bath composed of 25 g chromic acid, 133 ml glacial acetic acid, and 25 ml water. This electrolyte has been used and recommended for preparing specimens for optical metallography It was necessary to mask the edges of the sample with a stop-off paint in order to prevent preferential attack in these areas. The paint used was made by dissolving polystyrene in benzene. The electrolytic cell consisted of a cylindrical stainless-steel cathode placed in a beaker containing the electrolyte, with the sample as the anode positioned at the cell axis. The temperature of the electrolyte was held below 15°C by cooling with liquid

Jan 1, 1963

By A. A. Janke, G. J. Vogel, W. M. Swift

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations, and design studies are being carried out by various organizations under contract with the Department of Interior (Office of Coal Research, OCR) and with the U.S. Environmental Protection Agency, (EPA). The Atomic Energy Commission's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. The principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process are covered in this paper. The participants in the multiorganizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1976

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By W. S. Landis

IN brief, this is the story of an attempt to Americanize a process originally developed in Europe. The story will be recited in two sections, the first dealing with the process as developed by the European engineers; the second containing the improvements and modifications of American origin, together with some details of the operating results of the unit as finally assembled. Developments in other directions in this same field have not, up to the present, pointed out an economic future for the process, therefore our record here is largely a report of development progress. Whether some particularly favorable location will be found at some future time for a commercial installation cannot as yet be fore-told. The project is now at a standstill. The peculiar tools of the electrometallurgist should be of great interest to the zinc smelter. The low thermal efficiency of the zinc retort, its comparatively small-scale unit and its intermittent cycle as it stood in 1925, should make this art a particularly fertile field for the electric fur-nace. Yet in spite of years of work recorded in volumes of literature, and an expenditure of large sums of money, there is not a single electrothermic zinc smelter operating anywhere in the world. In this industry the electric furnace plays only a secondary part today.

Jan 1, 1936

By A. E. Bellis

ROBERT J. ANDERSON, Cleveland, Ohio (communication to the Secretary *).-The paper by Messrs. Bellis and Hardy was interesting to me and has led me to make a few remarks concerning some of the points brought out. The question of employing correct hardening temperatures is one that is sadly neglected, particularly in many large plants that forge and treat their machine tools for private use. As is most aptly remarked in this paper, "The custom of using one, high-speed temperature for all tools is very poor practice;" still, such practice is more common than otherwise. An instance came to my attention some time ago, in connection with some work with the standardization of high-speed steels for machine tools, where there were no less than six different brands of alloy steels being used for machine tools such as lathe, shaper, planer, boring mill and cutters of like nature. All of these different steels received identical heat and forging treatment-or at least that was the aim of the tool hardener. That the results were highly unsatisfactory goes without saying. That the hardening department of many plants is conducted on a rule-of-thumb fashion is the reason for a great deal of the trouble and disappointment which seems to be the lot of many tool-steel users. Exceedingly crude execution is the rule rather than the exception, and it is no small wonder that the results are as good as they sometimes happen to be. It would seem that at the present price of alloy steels the subject should receive a closer scrutiny by purchasers than it does. One not familiar with the workings of souse plants that disdain to lend an ear to scientific heat treatment would scarcely give credence to some of the methods employed, not only in the treatment of the steel but also in its selection and purchase. Heating for hardening should be conducted under close pyrometric control only after the correct hardening temperature has been determined.

Jan 3, 1917

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By Walter Crafts

Structural steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwallal (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time. General Effects of Chromium Chromium is so widely known for its carbide-forming tendency that its capacity to stabilize oxygen, nitrogen, and phosphorus is often overlooked. In low-carbon steels of the structural type these so-called secondary characteristics become more prominent. For this reason also, chromium in structural steel is definitely a toughening agent. As the carbon content is increased, the more widely known hardening effect becomes more evident. In low-carbon steels chromium increases the notched-bar impact strength substantially. This property persists at subzero temperatures and is utilized for low-temperature service in chromium-copper steel.4 Chromium also reduces any tendency to strain-aging embrittlement. In addition to improving the toughness of steels with the usual impurities, chromium has the specific property of counteracting the brittleness induced by high phosphorus.5,6 In steels low in carbon and alloys, chromium has an almost negligible effect on tensile strength, and a hardening influence is noticeable only in the stronger steels. The ductility of welds adjacent to the base plate is also improved by chromium, both in the range of foolproof welding steels having strengths of less than 80,000 lb. per sq. in. as well as in the higher strength steels.

Jan 1, 1939

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Eric Jette

THE unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investi-gations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrews1. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treat-ment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900° to 950° C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today.. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points

Jan 1, 1936

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

By S. Leber, R. F. Hehemann

Diffusion coefficients for the Cb-W system were measured using couples prepared from poly crystalline, commercially pure metals. The diffusion coefficients, measured in the temperature range between 1700° and 2300°C, decreased exponentially as the tungsten concentration was increased from 0 to 50 at. pct, then decreased abruptly at higher concentrations. A decrease of two orders of magnitude was observed over the entin? compositional range. The diffusion coefficients were in the range defined by the self-difiusion coefficients of the individual elements, indicating their general validity. An activation energy of 60,500 cal per mole was measured for the 20 pct W composition. Such low values, when compared with energies over 100,000 cal per mole for the pure constituent elements, indicated that transport mechanisnzs more rapid than volume diffusion were contributing substantially to inter dijfusion. Difference should, therefore, be expected between these data and the intrinsic diffusion coefficients. These differences should be significant in the kinetics of 'transport phenomena in practical systems. CONSIDERABLE attention has been devoted in recent years to the mechanical behavior and other properties of the refractory metals and their alloys. The Cb-W system has been of special interest as a base for the development of more complex compositions of commercial interest. In spite of the importance of mass transport to all aspects of elevated-temperature behavior, and especially to the production of alloys by powder-metallurgy techniques, little attention has been paid to diffusion in the Cb-W system. Results from a previous study of this system1 appeared to be anomalously high. The present investigation is, therefore, an attempt to obtain more accurate diffusion coefficients in this system. Intrinsic diffusion coefficients, of primary importance from the theoretical viewpoint, can only be obtained accurately from studies utilizing compositional gradients approaching zero. However, many practical problems involve diffusion under significant concentration gradients. The diffusion coefficients determined in this investigation were, therefore, obtained from couples prepared from elemental metals. The data obtained should be of value in the analysis of problems such as homogenization during powder-metallurgy alloying or reactions between base and clad in coated structures. In this vein, the investigation was conducted on poly crystalline materials of commercial purity. PROCEDURE Diffusion couples were prepared by sandwiching a columbium sheet between two sheets of tungsten. The composite was welded around all edges, the tungsten forming a protective can for the columbium. The composite was soaked for 4 min at 1600°C in a hydrogen-atmosphere furnace, quickly forged to 40 pct reduction in thickness, and then rapidly cooled to room tempera-

Jan 1, 1967