Search Documents

By Wilford L. Stork

Certain influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,l such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, 'thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is redly burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the . world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book.3 The work of J. E. Johnson, Jr., has revolutionized the metallurgy of cast iron and it seems apparent that all future work must include an oxygen determination just as we include silicon, sul-

Jan 1, 1920

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. 'The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar' trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser's,Ar' temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

APPROXIMATELY 3500 people thronged the Hotel Statler from February 18 to 24 for the 173rd general meeting of AIME. It was a technical extravaganza in that 82 technical sessions were held, at which 500 authors presented some 350 papers. Fortunately, Jerry Peirce, outgoing President, didn't have, to preside at all the events although after his year's stint as President, he has more than a nodding acquaintance with some of the latest problems in the mining, metals, and petroleum industries. Although the Welcoming Luncheon on Monday noon was the official opening of the meeting, Local Section Delegates and the Board of Directors convened on Saturday and Sunday, respectively. The large attendance and business like demeanor of these two groups was in accord with the energetic and competent service they have rendered the Institute through the year. To the applause of engineers and their wives who thronged the grand ballroom of the Statler for the Welcoming Luncheon, President Peirce introduced Oliver B. Hopkins, president of the Canadian Institute of Mining and Metallurgy and C. Gerow, secretary of CIM. Dr. Hopkins brought greetings from the CIM and expressed his satisfaction in the splendid spirit of cooperation that exists between the two Institutes. Dr. Hopkins is president, Interprovincial Pipe Line Co., Toronto, and counts as a close personal friend M. L. Haider, who is the 1952 President of AIME and lately of Toronto where he was a director and general manager of Imperial Oil Ltd. Mr. Haider will be known shortly as Mike to thousands of AIME members as he makes his Local Sections presidential tour. There was a pause in luncheon proceedings when Judge Harold R. Medina arrived amid the applause of the audience and somewhat breathless from his trip via motorcade from an antitrust trial against investment bankers at the courthouse downtown. With the Judge at his elbow, President Peirce took the opportunity in his introduction to good humoredly chide the Judge for the vixenish habits of public servants in their treatment of astute businessmen. The successful inventor who patents his inventions is a monopoly; the copper manufacturer who buys his competitors a drink is in collusion; but the business failure need only look to the government for a subsidy, Mr. Peirce pointed out. Judge Medina, quickly captured the admiration of his listeners. He spoke about justice, deploring partisan deals on nominations for judge-

Jan 1, 1952

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05 ? ACKER, E. O'C., Supt., Treatment Dept., Bethlehem Steel Co., So. Bethlehem, Pa. '86

Jan 1, 1910

By F. W. Lee

Historical-From the beginning of time, all ingenuity of mankind has been concentrated upon the methods of finding gold and unusual deposits in the earth. An illustration (Fig. 1) from the old treatise by Agricola, "De Re Metallica," published in 1580, will serve to show the im-plicit faith of that generation in divining methods. However, it was not until 1920 that real progress was made in prospecting by using the latest advances of the physical sciences. The public interest was stimulated by the successes of these methods on the part of commercial oper-ators, and governmental agencies received many requests for information concerning their relia-bility. There were also, in the late 1920's.high- pressure mine-promotion schemes which used geophysical methods in a very questionable manner, symbolized in Figure 2 as of 1928 by an elec-trified forked stick. Authoritative information concerning such practices for public protection was needed to curb such notorious undertakings. Dr. Scott Turner, then Director of the United States Bureau of Mines, thoroughly understood the situation and was first in the governmental de-partments to recognize the possible value of a study of modern prospecting methods. The Bureau of Mines began this investigation by employing Drs. A. S. Eve and D. A. Keys of McGill University for short periods in the summer in 1927. Their first publication [see 1 of "References" at end of paper] served to illustrate the fundamental scientific principles which underlie geophysical prospecting. This was followed by a second publication [21 giving the results of field-tests. In the light of the rapid improvements during the intervening ten years, these two papers take a historical position. Later a full-time position under Civil Service was planned by the Bureau of Mines for con-tinuous investigations and research concerning geophysics and its applications to prospecting. It was Turner's idea that. since the oil-industry had been making very rapid progress with good results, if mineral mining could also benefit to the same degree, it would be of great help to that industry.

Jan 1, 1940

By J. H. Westbrook

IT is always of interest to document the origin of real microstructures which closely approach various idealized morphologies. Such instances constitute excellent bases for experimental studies of the effect of microstructure on properties. Typical examples include the eutectoid steels (lamellae) used by many investigators and the two phase Cu-Cr alloys (spheres) recently employed by Hibbard and Hart The present note describes a structure with cylindrical particles. In a study of certain alloys in the Cr-C system, an alloy was arc melted whose composition was very close to the aCr-Cr,C, eutectic (3.2 wt pct C, according to the latest phase diagram published by Bloom and Grant2). The alloy was not analyzed but previous experience with the melting technique employed indicates good correspondence between intended and analyzed compositions with negligible tungsten contamination from the electrode. The phases present in the alloy were identified by X-ray powder patterns as a chromium and Cr,C,. Typical micrographs, presented in Fig. 1, show unmistakable evidence of the cylindrical geometry of the carbide phase. The eutectic grains are randomly oriented and, consequently, only a few show the true fibrous nature of the carbide particles, most being cut so as to show slightly elliptical cross sections. Within any particular grain, remarkable uniformity is to be observed with respect to the size, shape, spacing, and orientation of the carbide particles. Length to diameter ratios have been estimated from the micrographs to be at least 250:1, with diameters of about lp. This alloy may be of further interest from different viewpoints. On the one hand, it might be used to check the applicability of the equations derived by Fullman3 for computing true particle dimensions of cylindrical particles from opaque random sections. On the other hand, it might be possible to extract the carbide particles from this alloy and repack them in a ductile matrix to form a synthetic structure of the type discussed by Metcalfe et al.4 With the large l:d ratio and the small diameter of the carbide fibers, it is likely that the interdefect distance in each fiber is sufficiently great to permit realization of a large fraction of the presumed high strength of the carbide. References 1W. R. Hibbard, Jr. and E. W. Hart: Dispersion Hardening of Copper-Chromium Alloys. AIME Trans., 1955, vol. 203, p. 200; Joun-nal of Metals, January 1955. 2D. S. Bloom and N. J. Grant: The System Chromium-Carbon. AIME Trans.. 1950. vol. 188. p. 41; JouRnal of Metals, January 1950. aR. L. Fullman: Measurement of Approximately Cylindrical Particles in Ooaaue Samples. AIME Trans.. 1953, vol. 197, p. 1267; Journal of Metals. ~ebtember 1953 4 A. G. Metcalfe, C. H. Sump, and W. C. Troy: Fiber Metallurgy. Metal Progress, 1955, vol. 67, p. 81.

Jan 1, 1958

By Frederick Beckett

WIDESPREAD experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this difficulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.1 Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly aus-tenitic ; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater per-centages. The results of the work to be described disclose that titanium and columbium in proper proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valu-able properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimum corrosion resistance, the producer strives for a carbon content as low as commercially practicable.

Jan 1, 1933

By H. L. Riley, B. W. Gandrud

AS far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales.' The system has been described and discussed in a number of publications.2-5 The following is quoted from an abstract of the latest of these,5 a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption. The situation referred to above explains why an investigation is being made of the possibilities of achieving better cell capacities. Results obtained from this investigation, which is still in progress, are believed significant with regard to both cell capacity in general and the relation of cell design to cell capacity in particular. Commercial equipment now being used in a laboratory-type investigation should have performance characteristics similar to those of the larger machines. Equipment and Procedures: All flotation tests have been made in a standard Denver sub-A 24x24-in. unit cell of 12-cu ft volume. Cell modifications to make it more suitable for the tests were an adjustable front-wall section for varying cell depth and a perforated scraper-drag assembly for removal of the float product. There is also an apron dry-coal feeder, a gravity-feed water supply, reagent feeders, and a centrifugal pump that feeds the mixture of coal, water, and reagents into the flotation cell. A wattmeter connected into the drive-motor circuit records the power requirements of the impeller throughout each run. Dry coal, water, and reagents are all fed through a pan-type intake to the feed pump. A Sturtevant blower was set up to furnish air for supercharging. A centrifugal pump with a garbage-can intake provides for disposal of refuse flow to an outside settling tank. Figs. 1 and 2 show the flotation cell; Fig. 2 also illustrates the blower for supercharging. For purposes of this investigation, the percentage by weight of the feed coal recovered in the float product under a standard set of conditions has been considered as the criterion of cell capacity. The authors realize that such a criterion may be somewhat unorthodox, as the term cell capacity is usually understood to refer to feed input and ordinarily takes into account the ash analyses of the float product and refuse. However, the word capacity is flexible enough so that Webster gives one definition as maximum output, a definition which seems to justify, at least partly, acceptance of the above criterion. It has been the authors' experience in the Birmingham district that the ash-reduction efficiency of the coal-flotation process is generally satisfactory and that the only real problem is to increase the rate of float recovery so that the feed rate to any given bank of cells can be increased without undue loss of coal in the refuse. Originally it was planned to operate the flotation cell to simulate continuous operation during sampling periods. It was assumed that operating for reasonable time with feed coal, water, and reagents turned on would stabilize conditions so that the weight of float coal discharged during a fixed time interval would be an accurate measure of the rate at which the coal was being floated. It developed, however, that this supposition was erroneous. The float coal, caught for fixed time intervals and weighed, gave widely varying results in duplicate runs. Efforts to correct this trouble failed, and it was decided to try to operate on a batch-test basis, whereby all the float coal produced during a run on a known weight of feed coal would be caught in tubs, dewatered, and weighed. This method gives consistent and reproducible results, with total float product weight rarely varying by more than 3 or 4 pct on duplicate runs. The standard test procedure is as follows: A 132-lb sample of dry feed coal is weighed and placed in the feed hopper. The feeder is adjusted for a rate of 800 lb per hr. Feed water and reagents are turned on, and the feed and refuse pumps are started. One minute later the impeller is started. Six minutes are allowed for the cell to fill up with the water-reagent mixture. The feed of dry coal is started at the end of this 6-min period. One minute later the float-coal removal drag is started. The float coal is caught in one tub for the first 6 min after the flow of feed coal starts. Tubs are then changed, and the float coal is caught in a second tub until the feed coal runs out, when the tubs are again interchanged to catch the float coal for the remainder of the run in the first tub. The cell is kept running for 3 min with the water and reagents on after the feed stops to allow residual float coal to be removed. At the end of a test the wet float coal in both tubs is weighed and the total weight recorded. The product in the second tub is used for moisture determination and screen-size analyses. When the

Jan 1, 1956

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith' and of A. G. H. Andersen .2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford," using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,1,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates h in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By K. G. Wikle, W. W. Beaver

A general survey of the mechanical properties of commercially pure beryllium fabricated from powder by vacuum hot pressing and other consolidation methods is presented. The effect of fabrication method, grain size, strain rate, and directionality upon both room and elevated temperature tensile properties is reported. BERYLLIUM metal, in spite of its rather restricted use, has been the object of attention for many researchers in the past half century. However, such work was performed on special experimental lots of metal made in small quantities by a variety of reduction methods. Not until 1946 was there a substantial production of beryllium metal, and not until 1950 was there a steady production of a commercially standard beryllium in the United States. This output was both the result of a requirement of the Atomic Energy Commission for a high grade beryllium of consistent quality and the development of a powder metallurgy process, by the Brush Beryllium Co., known originally as Process Q, which yielded a fine grained beryllium suitable for fabrication. Because this powder metallurgy product, known as QMV, superceded other types of metal made previously and represents the great majority of beryllium in use today, it seems worthwhile to present the results of studies on the mechanical properties of this metal as currently made. To the design engineer and the metallurgist, beryllium has extremely interesting properties. It is as light as magnesium alloys while having a stiffness modulus 40 pct greater than steel and a strength-weight ratio superior to titanium and aluminum alloys and aircraft steels. The melting point is high, 1287°C (2348°F), and it has good corrosion resistance both in air and water. Also, it is highly transparent to X-rays and has good heat and electrical conductivity (electric conductivity is greater than 40 pct of Cu). To the atomic energy program beryllium is considered a valuable material because of its low neutron-capture cross section and high neutron-scattering cross section which make it a good moderator and reflector for the lower velocity neutrons. A major technical difficulty limiting the use of beryllium, especially in structural applications, has been its notch sensitivity and consequent room temperature brittleness. Kaufmann, Gordon, and Lillie1 have reported their work on the mechanical properties of beryllium performed from 1946 to 1950. They studied the room and elevated temperature properties of cast and extruded beryllium and extruded electrolytic flake, Table I. Cast and extruded alloys of 85 to 99 pct Be were tested also. They found that extruded metal developed good strength and appreciable ductility in the extrusion direction and that thermal treatment and alloying provided little improvement in mechanical properties. They concluded that preferred orientation and fine grain size were the means of obtaining optimum tensile properties in beryllium. Other investigators have measured and commented on one of the most striking mechanical properties of beryllium, namely, its abnormally low Poisson's ratio.2 Udy, Shaw, and Boulger3 presented the latest published survey on properties of beryllium but their information is based only on published data available before April 1949 and cites little information on metal fabricated by powder metallurgy

Jan 1, 1955

There are no data available of shipments until 1858, and then estimated, when railroad service became available. By reason of the iron made in the county, and the large amounts of salt, the tonnage used locally was quite large, and until 1860 these are estimated from the probable salt and iron production. After 1859 the tonnages shipped by rail are partly estimated from the total shipments of the Allegheny Valley Railroad from four counties. It is believed that the totals are below, rather than above, what the actual production was. While considerably larger for the same years than figures given by the Secretary of Internal Affairs and census reports, these data were always too low in those days, partly because of lack of facilities for gathering them, but more largely because of the strong prejudice existing in those days against furnishing such data to any governmental agencies.

Jan 1, 1942

By H. L. Riley, B. W. Gandrud

As far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales. The system has been described and discussed in a number of publications. The following is quoted from an abstract of the latest of these," a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption.

Nov 1, 1955

By John Griffen, David H. Davis

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow's kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan's death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944

By David H. Davis, John Griffen

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow's kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan's death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944