Search Documents

By O. G. Kiel, G. W. Swift

The concept of "a continuous succession of steady-states", which has been applied successfully by Aromfsky and Jenkins to obtain a solution for the nonlinear partial differential equation describing the transient Darcy flow of gas through porous media, is demonstrated to be equally valid for transient non-Darcy flow. A mathematical model, which numerically solves the partial differential equation, is used to check the validity of the succession of steady-states solution. Comparison of sand-face pressure histories compelted by the two methods shows excellent agreement. The utility of the succession of steady-states solution in predicting performance of gas wells rests in the fact that no special computation equipment is required. The development of the succession of steady-states solution leads also to a practical method for determining and analyzing field test data. A method for taking gas-well test data under constant-rate conditions is presented. Experimental data obtained in the field by employing the constant-rate method are presented and analyzed in accordance with the succession of steady-states solution. Analysis of data in this fashion is demonstrated to give direct "in situ" information for reservoir permeability, porosity and turbulence or non-Darcy coefficient. INTRODUCTION The economics of gas production are dependent upon the transient behavior of flow within the reservoir. For production from a finite reservoir, the transient flow behavior can be subdivided into two parts. At first, the transient caused by the movement of the pressure "wave" into the reservoir is of importance. Later in the production history, the pressure-wave movement ceases and the second transient stage of material depletion becomes controlling. For reservoirs of relatively high permeability, it can be shown that the pressure wave moves into the reservoir and stabilizes quite rapidly. In the case of relatively impermeable reservoirs, quite the opposite is true. Although it is theoretically possible to compute the production capability of a well from the properties of the reservoir as determined by static tests and core analyses, more reliable information is obtained by conducting flow tests on the well and thereby obtaining some measure of "in situ" formation properties. For gas wells, there are two basic types of tests in existence: the flow-after-flow method,' and the isochronal method.' Both of these techniques are tailored to obtain data that can be analyzed in accordance with the empirical performance equation: In addition, the isochronal method makes provision for the sluggish nature of pressure-wave movement in "tight" formations by requiring pressure build-up between flows and by stipulating that data obtained on successive flows be analyzed at equal elapsed flow times. It can be demonstrated that either test is valid for reservoirs of high permeability. Further, since it has been pointed out that the pressure wave stabilizes rapidly for reservoirs of this type, tests of relatively short duration will give stabilized information on the performance of a well. Further decline of sand-face pressure and/or production rate may be determined by employing material-balance techniques. Cullender' points out that for relatively impermeable reservoirs the flow-after-flow method gives invalid results. (See Appendix C.) If the isochronal method of testing is used, there are two alternatives: (1) the tests must be conducted for a sufficient length of time to obtain stabilized information (which may require months to accomplish); or (2) some method for extrapolating the results of short-term isochronal tests must be employed. The first alternative is impracticable because of manpower, conservation and economic considerations. Recourse to the second alternative requires some assurance regarding the reliability of the extrapolation technique. Poettmann and SchilsonJ present an empirical method for predicting stabilized performance. The present investigation was originally initiated to determine the reliability of this technique. To do this, a mathematical model was developed to simulate the Darcy and non-Darcy flow of gas through porous media. The model consisted of a finite-difference approximation of the nonlinear partial differential equation which was solved on an IBM 7090 computer. Long-term production histories were simulated by the model and compared against predictions obtained from the Poettmann-Schilson method. As the work progressed, it became apparent that a straightforward predictive equation could be developed by utilizing the concept of a succession of steady-states. As a result, the emphasis of the work was redirected to exploit the advantages of the new method.

By D. A. Flanagan, P. B. Crawford

A study has been made of the feasibility of storing liquid meihane at low pressures in undergrohd caverns. Methane liquefies at — 258°F at atmospheric pressure. It is shown that the methane evaporation rates will rapidly decrease and cool the surrounding rock so that at the end of one month they would be between 50 Mcf/hr for a cavern of 25-ft radius and 700 Mcf/hr for a cavern of 100-ft radius. At the end of 10 years, the evaporation rates would be 18 and 100 Mcf/hr, respectively, for caverns of the same radii. The evaporation rates may be reduced by a factor of 2 to 10 by the application of insulation. The cost for mining the caverns is estimated to be $.75 to $1.25/Mcf of storage. This is substantially less than surface storage; it is believed to be safer and to result in lower maintenance, savings in space and savings in strategic materials. INTRODUCTION During the past few years, there has been an increasing interest in the economic feasibility of liquefying methane. Methane liquefaction is being considered for tanker transport; in addition, liquefaction is being reconsidered for shaving peak gas demands. Several articles have described natural gas liquefaction and the progress of the tanker in making trial runs from the United States to Great Britain to determine the feasibility of tanker transport. At the present time, pipelines are not designed to supply peak gas loads during extremely cold periods such as are oiten encountered in the North and Northeast. Gas is being stored in underground reservoirs en-route to its destination, but in many instances satisfactory storage in porous reservoirs has not been practical, especially along the Eastern seaboard where few petroleum reservoirs have been found. In England and other foreign countries, it is unlikely that satisfactory porous structures could be found, and it may be desirable to mine or excavate the rock to obtain storage. By storing the methane near the consumption point, product availability can be increased during periods of need. Methane liquefies at - 258OF at atmospheric pressure, and 1 cu ft of liquid methane will make about 600 cu ft of gaseous methane. Methane liquefaction for shaving peak gas demands was conducted in Cleveland, Ohio in the early 1940's. The Cleveland plant was designed to liquefy 4 MMcf/D of natural gas.' Development of several low-temperature processes has resulted in some improvements in the design of low-temperature storage vessels. Liquefied-methane storage vessels can be designed for various evaporation rates. The desired rate will depend on the reason for liquefaction. For shaving peak gas demands, the desired evaporation rates would be low, possibly between 0.2 and 1.5 per cent/day. For methane tanker transport and supply, the evaporation rates must be high and must equal the total daily rate of supply. It is apparent that the cost of storage facilities will depend on the objective and will vary appreciably. Surface storage of methane may cost between $3,000 and $20,000/MMscf, depending on the size and design. The failure of the surface storage vessels at Cleveland, with the resulting injury and loss of many lives, has caused considerable emphasis to be placed upon developing new, safer and improved methods of storing liquid methane. Storage of liquefied propane and butane in underground salt domes has been very satisfactory. The per-barrel cost of underground storage for any sizeable capacity is very small compared to the cost of surface storage for LPG mixtures. The larger the capacity of the underground storage, the less is the per-barrel cost. Numerous advantages appear to exist if liquefied methane could be satisfactorily stored underground, the principal advantages being increased safety, lower initial cost, lower maintenance cost, savings in space and savings in strategic materials. The purpose of this paper is to determine the feasibility of storing liquid methane underground in mined caverns. If a large spherical cavern is dug underground and is filled instantaneously with liquid methane, the surface of the sphere may approach the liquid methane temperature almost instantaneously. The temperature distribution for a sphere of radius r. in an infinite medium, initially at one temperature with spherical surface kept at T, from time t = 0, is given by Eq. 1.'

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C'. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h'b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,' by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K' is the value for the Fe-S binary solution. and the limiting value of K' in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1' that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

By Douglas J. Robinson

A pilot scale process has been developed to separate mercury, tin, silver, and copper from dental amalgam scrap. Laboratory research led to a process which was operated in 55 gallon drum sized reactors to treat 2000 Tr oz charges of scrap per day. This paper discusses the development work, presents a flowsheet and gives an indication of the equipment necessary to carry out the process on a commercial scale.

Jan 1, 1984

By J. E. Wilson, F. P. Lebar

TYPICAL of southwestern Wyoming are coal structures that dip from 4° to 17°. Those at the Reliance and Winton mines of the Union Pacific Coal Co. average 91/2 and 15°, respectively, and dip almost directly to the west. By using a hoist for main haulage, a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 ft. a two-entry system is driven to the north and to the south. In both fields, which are nongassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy loader was introduced into The Union Pacific Coal Company's operations, slopes, aircourses, and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 ft. and entries at 230 ft. Connections to the workings above were made by driving up the pitch 75 ft. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a I¼-in. hemp rope dou- bling around it and having me end attached to the car and the other to the mule. The mulc, pulling downhill, raised to the working face a small wooden car of one-ton capacity. With the introduction of mechanical loading, mule haulage and small wooden cars disappeared and auxiliary hoists, electric locomotives, and steel cars with a capacity of 4 tons were substituted. Development work was done during two or three shifts of the 24-hr. period. Driving of haulage slopes down the pitch by hand continued. Crosscut intervals were changed to Ioo ft. and the crosscuts were driven with shaking conveyors. With the use of a 90° swivel, aircourses and manways were driven up the pitch. Entry intervals were changed from 230 ft. to 300 feet. Mobile loaders of the Joy type were first employed by this company in the year 1923 at Hanna, Wyo. In 1928, two 4-BU Joy loaders were transferred from Hanna to Winton No. I mine, where they were used in driving slopes and entries. At the time of transfer, the machines were about worn out and were not suited to the steep pitch, therefore frequent breakdowns occurred. However, experience justified the belief that the mobile loader was fitted for driving slopes in this field. During 1937 a unit was installed in Reliance No. 7 mine, and during 1939 one in Winton No. 7½ mine. With the introduction of this type of mobile loader, a new era of development began. Speed undreamed of in hand-loading days became a reality. The cost of development down the pitch has been reduced until it

Jan 1, 1942

By H. M. Morse

This report on oil and gas development in Mississippi covers the period from Jan. I, 1944, to Dec. 31, 1944: Salt Domes During the year six salt domes were drilled for sulphur, but no commercial sulphur deposits were found. One salt dome, the Bruinsburg, in Claiborne County, has produced gas- at 935 to 940 ft' in Moody's Branch marl. The Stringer salt dome in Smith County and the Ruth salt dome in Lincoln County both had a slight showing of heavy oil. Other salt domes have been dry. In addition to the Bruinsburg dome, the Allen salt dome, in Copiah County, and the Richton salt dome, in Perry County, were discovered in 1944; also the Sumrall dome, in Covington County. New Oil Fields Baxtemille Oil Field.—The Baxterville oil field was discoveredby the Gulf Refining Co, in sec. 7, T. I N., R. 16 W., Lamar County. At the end of the year this field had one oil well, with two active operations. Production for 1944 was 1047 bbl. of oil. GwinvilLe Field.—Gwinville field was discovered by S. W. Richardson, in sec. 24, T. 9 N., R. 19 W., Jefferson Davis County. This discovery well was a gas-distillate well, the oil being crystal clear. At the end of 1944 there were two gas wells and one oil well in the field. The oil well is approximately 2 1/2-miles from the gas- distillate wells. Gas production was 55,801 M cu. ft. and the distillate production was 2644 barrels. Heidelberg Oil Field.— The Gulf Refining Co. discovered the Heidelberg field in sec. 30, T. I N., R. 13 E., Jasper County, in January 1944. This field has by far exceeded the other 1943 and 1944 discoveries, having approximately 56 oil wells, 7 dry holes, and 10 active wells at the end of the year. Production to Jan. I, 1945 was 1,441,192 bbl. of oil. Mallalieu Oil Field.—The california Company discovered the Mallalieu oil field in set. 10, T. 7 N., R. 8 E,, Licoln. County. At the end of the year there was one well in the field with three active operations. Production was 32,303 bbl. of oil. Old Oil Fields Brookhaven Oil Field, in Lincoln County, has one oil well, which produced 2590 bbl. of oil during 1944. CarY Oil Field, Sharkey County1 has only one producing well, which produced 11,818 bbl- of oil during the Year- In Cranfield Oil Field, dams County, II oil wells and two gas-distillate wells were drilled in 1944 and there were five active wells on Dee. 31, 1944- The total production for the Year was 5251422 bbl-of oil. The gravity of the oil is 40" to 54.9'- In Eucutta Oil Field1 Wayne County1 34 oil wells were completed during 1944. There were five dry holes and six active wells at the end of the year.. The field produced 454,332 bbl. of all d the average gravity is 25" Flora Oil Field, Madison County, pro-

Jan 1, 1945

By J. E. Wilson, F. P. Lebar

TYPICAL of southwestern Wyoming are coal structures that dip from 4° to 17°. Those at the Reliance and Winton mines of the Union Pacific Coal Co. average 91/2 and 15°, respectively, and dip almost directly to the west. By using a hoist for main haulage, a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 ft. a two-entry system is driven to the north and to the south. In both fields, which are nongassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy loader was introduced into The Union Pacific Coal Company's operations, slopes, aircourses, and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 ft. and entries at 230 ft. Connections to the workings above were made by driving up the pitch 75 ft. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a I¼-in. hemp rope dou- bling around it and having me end attached to the car and the other to the mule. The mulc, pulling downhill, raised to the working face a small wooden car of one-ton capacity. With the introduction of mechanical loading, mule haulage and small wooden cars disappeared and auxiliary hoists, electric locomotives, and steel cars with a capacity of 4 tons were substituted. Development work was done during two or three shifts of the 24-hr. period. Driving of haulage slopes down the pitch by hand continued. Crosscut intervals were changed to Ioo ft. and the crosscuts were driven with shaking conveyors. With the use of a 90° swivel, aircourses and manways were driven up the pitch. Entry intervals were changed from 230 ft. to 300 feet. Mobile loaders of the Joy type were first employed by this company in the year 1923 at Hanna, Wyo. In 1928, two 4-BU Joy loaders were transferred from Hanna to Winton No. I mine, where they were used in driving slopes and entries. At the time of transfer, the machines were about worn out and were not suited to the steep pitch, therefore frequent breakdowns occurred. However, experience justified the belief that the mobile loader was fitted for driving slopes in this field. During 1937 a unit was installed in Reliance No. 7 mine, and during 1939 one in Winton No. 7½ mine. With the introduction of this type of mobile loader, a new era of development began. Speed undreamed of in hand-loading days became a reality. The cost of development down the pitch has been reduced until it

Jan 1, 1942

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By N. Mungan

Laboratory water floods were performed in oil-wet and waterwet alundum and Torpedo cores, displacing a refined oil with n-hexylamine or Triton X-100 solution. Also, some floods were performed in which a sucrose solution was displaced with n-butyl alcohol. The Purpose ot the tests was to see if the oil recotlery could be increased and to examine what role the inter-facial tension reduction and wettability change play in the recovery mechanism. it was found that the chromatographic transport of amine was influenced by core wettability. In oil-wet cores, the rate of advance of the amine band could be predicted from equilibrium chromato-graphy, while in water-wet cores the amine band moved faster than predicted, indicating a non-equilibrium process. By reducing the interfacial tension to 1.1 dyne/ cm, oil recovery was increased. More oil was recovered from Dri-filmed cores than from water-wet cores. Reversing the wettability of the porous media from oil-wet condition also resulted in some additional oil recovery. Neutral wettability floods did not increase oil recovery. INTRODUCTION Interfacial forces in petroleum reservoirs are responsible for retention of large quantities of residual oil. Increasing exploration costs have created an incentive to attempt recovery of this residual oil by new and novel processes. One novel process involves changing the interfacial forces by introducing a chemical into the reservoir during water flooding. Recently, several investigators have carried out laboratory displacement tests using amines. lt3.4 The amines adsorbed onto initially water-wet core surfaces, changing them to oil wet. Additional oil was recovered when the cores were flooded in a manner reversing the. wettability from oil-wet conditions. In all these studies, the wettability reversal was considered responsible for increased oil recoveries although it was noted that amines also reduced oil-water interfacial tension. In the present study, displacement experiments were performed in water-wet and Dri-filmed cores. The purpose was to separate the effects of lowering the interfacial tension from changing the wettability. LABORATORY STUDY All experimental data given in this paper have been obtained at a temperature of 70F + 1 and prevailing atmospheric pressure. FLUIDS AND MATERIALS The oil used in these experiments* was washed with H2S04 and passed through two 100-200 mesh silica-gel beds to remove unsaturates and surface active impurities. Normal hexylamine** of practical purity was used, and the alundum cores*** were composed of nearly pure A1203. Fused quartz (SiOi) and Lucalox (A12 )t plates were used in the contact angle measurements. DISPLACEMENT TESTS Displacement tests were performed in alundum and Torpedo cores. Before displacement runs, cores were acidized with 0.1 normal HCI, flushed with distilled water and fired at 1,200F to make them water wet. This procedure also reduced water sensitivity of the Torpedo cores. Oil-wet cores were prepared from water-wet cores by flowing several pore volumes of 1 per cent by weight Dri-film SC-87 solution in heptane through the cores, flushing the cores with nitrogen, evacuating, and finally heating the cores at 300F for 4 or 5 hours. Between floods, cores were cleaned by conventional procedures and treated again as above.

Jan 1, 1965

By Howard R. Keil

Reactor at Carlton mill successfully calcines pyrite-telluride flotation concentrate for cyanidation. CARLTON mill in the Cripple Creek district, 45 miles southwest of Colorado Springs, Colo., has been in operation for approximately three years, treating the custom sulpho-telluride ores formerly handled by the Golden Cycle mill in Colorado Springs. At the new mill the pyrite-telluride flotation concentrates have been roasted, prior to cyani-dation, in a Dorrco FluoSolids reactor, which has proved capable of yielding calcine readily amenable to cyanidation. Incoming ores are crushed at Carlton to % in. and sampled in 30 to 75-ton lots before the individual lots are mixed in the fine ore bin. The composite ore then goes to the grinding circuit. Classifier overflow from the grinding circuit is treated by flotation to produce a concentrate containing approximately 85 pct of the values in 5 pct of the weight. The flotation concentrate goes to the FluoSolids reactor prior to cyanidation. Cyanide solution values are recovered by zinc dust precipitation. Flotation tailings are thickened and cyanided, the values from this part of the circuit being recovered from solution by activated carbon. Gold values in the flotation concentrates consist of a small amount of finely divided metallic gold; the tellurides, sylvanite and calaverite; and gold very intimately associated with the pyrite. The metallic gold and a part of the telluride values can be extracted from the concentrates by cyaniding without roasting. However, extraction on the tellurides by this method is not satisfactory, and the pyrite values are so intimately associated with the pyrite that very fine grinding and cyanidation for a prolonged period under ideal laboratory conditions does not yield good recovery. Upon roasting, the tellurides are oxidized to very finely divided metallic gold which is readily soluble in cyanide. The pyrite is oxidized mainly to a porous iron oxide which allows cyanide solution to penetrate to gold particles and take them into solution. Feeding the Reactor Flotation concentrates move by gravity to a thickener. Thickener underflow is discharged at approximately 60 pct solids, by means of a diaphragm pump, into a storage and blending agitator. From here the concentrates are pumped to a disc filter. The filter cake, at 84 to 88 pct solids, drops directly into a repulper where it is repulped into a slurry of 78 to 80 pct solids. The repulped filter cake flows into a 6x6-ft slurry agitator from which it is fed directly into the reactor by the Moyno pump. The Moyno pump has eliminated a large number of difficulties that were first encountered in feeding a wet concentrate to the reactor. On the original installation in Canada a screw feeder was used to introduce the filter cake directly into the reactor. Since the reactor is under a slight positive pressure it was necessary to have a suitable seal to prevent gas escaping from the reactor at this point. When the concentrates produced in flotation were coarse or granular they could be readily fed to the reactor but when fine-textured, clayey concentrates were produced a great deal of trouble was encountered.

Jan 1, 1955

By Michael Hoch, Seong Kwan Rhee

The ternary system Zr-Cr-0 was investigated at 1200°, 1500°, and 1700°C. The isotherms at these temperatures were determined by metallographic and X-ray diffraction analysis of carefully selected alloys. AS a part of a series of investigations1-4 of the ternary and quaternary phase diagrams on refractory metals and their compounds, the ternary system Zr-Cr-O was investigated at 1200°, 1500°, and 1'700°C. The binary diagrams Zr-Cr, Zr-O, and Cr-0 as reported by Hansen5 and Levin et a1.' and the existence of a ternary coompound ZrsCrsO (q-carbide structure a. = 11.96A) provided a good base for this investigation of the Zr-Cr-O phase diagram. MATERIALS The materials used and their suppliers were: Zirconium powder, 99.4 pct pure, Charles Hardy, New York; Zirconium dioxide, Fairmount Chemical Co., Newark, N.J.; Chromium powder, 99.85 pct pure, Fairmount Chemical Co., Newark, N.J.; Chromium sesquioxide, 99.86 pct pure, J. T. Baker Chemical Co., Pillipsburg, N.J. Though the materials used were not "hyperpure", the impurities present do not affect the results (lattice parameters, phase boundaries) within the experimental accuracy. EQUIPMENT AND PROCEDURE The detailed procedures and equipment used for this investigation were similar to those described elsewherel' "ith the exception that in this study an induction-heated argon-atmosphere furnace was used. The latter furnace was used to prevent the vaporization of chromium metal in samples in the higher temperature range (above 1200°C). The tungsten crucible was induct ion-heated in a vertical quartz tube filled with argon gas. The quartz tube was 1-1/2 in. in diameter and 10 in. long; it was connected at the top and bottom to water-cooled copper plates. The argon gas of a purity 99.995 pct was further purified by being passed through zirconium metal chips which were maintained at 800°C in a silica tube 1 in. in diameter and 30 in. in length. The furnace was flushed with argon gas for an hour before starting heating; during heating, a slight (3 cm oil) overpressure of argon was maintained in the system. Power was supplied by a 20-kw Ther-Monic Induction Generator. The samples rested on a tungsten-wire basket; the wire basket was connected to a tungsten wire which passed through the tungsten crucible lid, and entered the system on top through a Wilson-type seal. By pulling on the wire, the sample was removed from the crucible and dropped to the water-cooled copper base of the furnace. Because of the presence of argon gas, the cooling of the sample was even more rapid than in the vacuum furnace.' EXPERIMENTAL RESULTS AND DISCUSSION 1) Isothermal Section at 1200°C. The compositions investigated have been numbered within the phase diagram, Fig. 1, and all the pertinent information about the samples can be found in Table I. This table lists the composition of the samples, the phases present in the room-temperature diffraction patterns, the phases detectable in the microstruc-ture, and calculated lattice parameters of the a-zirconium phase. The shapes of the various phase

Jan 1, 1964

By Walter B. Lenhart

Introduction and Importance of the Industry Sand, as described in this chapter, is a crude product used for ballast on railroads and highways, and as the fine aggregate in concrete, mortar, plaster and in asphalt paving materials. The sand used in glass, as a molding sand, and as a source of silica is described in Chapter 43. Sand and gravel together constitute the mineral raw materials of largest volume produced from the earth. In 1958, as reported by the U.S. Bureau of Mines,21 680,080,000 tons of sand and gravel (including industrial sand) were produced in the United States. The nearest competitor was crushed rock of which 532,818,000 tons were produced. Coal, both bituminous and anthracite accounted for only 431,616,689 tons in the same year. In dollar value, sand and gravel were exceeded only by cement, crushed rock and fuels. Hence it is a major unit of the mineral-producing industry. As an example, one plant in California operates around the clock at an average rate of 1,500 tons per hour, and at peak intervals has shipped over 4,000 tons per hour, all by trucks. Nevertheless, it is controlled by one man through a panel of push buttons that control the crushing, screening, washing, grading, stock piling, and reclaiming of the products. Because sand and gravel are low-valued commodities, but are used in every construction undertaking in every city, village, farm, dam and highway, they are produced in almost every county in the United States and southern Canada, by thousands of individual operators, very few of whom operate in more than one community. Many operations, particularly those established to supply the needs of major dams that are under construction, or of major segments of new highways, are temporary in nature, and the equipment installed is more or less portable. Because of the bulky nature of sand and gravel, there is very little interstate movement, and almost no exports or imports, except a little movement back and forth across the border of the United States and Canada. First, the material needs definition. Definitions Sand and gravel have been defined as continuously graded unconsolidated materials that appear in the earth's surface as a result of the natural disintegration of rocks. Both normally appear together, but in a wide variety of sizes, types and range of size classification. The American Society for Testing Materials has tentatively revised its definition of "sand" as: granular material passing the 3/8-in. sieve and almost entirely passing the No. 4 (4760-micron) sieve and predominantly retained on the No. 200 (74-micron) sieve, and resulting from natural disintegration and abrasion of rock or processing of completely friable sandstone (ASTM Designation C 58-55T). The Society's tentative revision of its definition of "gravel" is: granular material predominantly retained on the No. 4 (4760-micron) sieve and resulting from natural disintegration and abrasion of rock or processing of weakly bound conglomerate (ASTM 125-55T). Sand and gravel deposits contain materials from the finest silt to the largest boulders. Chemical definition of the two materials is nearly impossible. Sand and gravel always are

Jan 1, 1960

By John R. Don

This paper, under the title of "The Genesis of Auriferous Lodes from a Chemical Point of View, Illustrated by Analyses of Samples Taken from the Chief Auriferous Area of New Zealand, Victoria and Queensland, by John R. Don, D.Sc., M.A., Lecturer on Geology in the University of Otago, N. Z.," was submitted by the author with the frank confession that its length, covering several hundred printed pages of the Transactions of the Institute, would preclude its acceptance for publication in full. But the great value of the original work which it records rendered its rejection on that ground highly undesirable ; and, after correspondence with Dr. Don, it was agreed that the Secretary should condense the paper, subject to the author's approval, omitting what was not essentially connected with the original work reported. In the discharge of this laborious and difficult duty, the Secretary's chief trouble has been his regret to cut out the acute criticisms and admirable theoretical and historical summaries of Dr. Don on the general subject of the science of ore-deposits. It should be added, that the original paper has been returned to the author, with full permission to publish it through any other medium (due mention being made of the first publication by the Institute of portions thereof), and a cordial expression of the hope that the treatise, as a whole, may be thus published, to the advantage of science. The Secretary begs to add, that many of the portions necessarily omitted from this condensed version would constitute, in his judgment, interesting and valuable separate contributions. In attempting to condense this paper, it was necessary at the outset to cut out the tint three chapters, of which the following brief outline is therefore given. Chapter I., introductory in character, indicates the importance of chemical analysis in the investigation of the genesis of ore-deposits, emphasizing the value of Prof. Posepny's Institute paper, and especially of the discussion which it aroused, and stating in general terms the theories of "lateral secretion" and "ascension." Chapter 11. describes the scope of the investigation undertaken by the author, the chief purpose of which was to determine which of the above-named theories was favored by the evidence obtained. This evidence consists chiefly (though not wholly) of analyses of the country-rock taken at various distances from the auriferous "reefs," (a) on deep mine-levels; (b) in the surface or "vadose" region : and also (c) of underlying, neighboring or connected crystallines (granite, gneiss, etc.). In addition to these investigations, there is a separate inquiry into the question of the deposition of gold in marine basins, suggested by the fact that most of the gold in the lodes of Australasia occurs in stratified deposits. Chapter 111. discusses the principles and methods followed by the author in the examination of country-rock for the purpose described. After giving his reasons for believing that careful tests of carefully-chosen samples of country-rock taken at varying distances from the ore-deposit might throw light upon the question

Jan 1, 1898

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By E. W. Davis

ABOUT a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½ -in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about zoo per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½ in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2 1/2 kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1945

By James B. Macelwane

THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these 'fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the. January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1952

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-''FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By E. H. Edwards, J. Washburn, E. R. Parker

The mechanism of strain hardening was discussed in connection with some recent observations on the stress-induced motion of dislocation boundaries and on the simple shear deformation of zinc, cadmium, and copper crystals. THE nature of work hardening accompanying plastic deformation of metals has long been the subject of speculation. As early as 1925, Becker' suggested a thermodynamic process to explain slip based on the statistical probability for the occurrence of local glide steps. The theory that plastic glide was due to the presence of lattice defects known as dislocations was first introduced in 1934 by Taylor: and Orowan, and Polanyi.4 Taylor presented a rather complete analysis of the behavior and interaction of dislocations. He assumed a certain type of stress field to be associated with a single dislocation, and postulated that work hardening would result from plastic flow in two ways. First, dislocations following one another across a slip plane might encounter a barrier which would impede their movement, thereby gradually diminishing and eventually stopping plastic flow on that plane. The second mechanism involved the concept of dislocations traveling in opposite directions on nearby planes attracting one another to form a meta-stable lattice. The interaction of dislocations in such an array was shown to be large enough to require an increase in stress before plastic flow would continue. Kochendorfer5,6 extended the concept of work hardening involving a back stress due to an accumulation of like dislocations on a slip plane. He suggested that the formation of a new dislocation is hindered by those dislocations already present. The hardening resulting from the interaction of newly forming dislocations with bound dislocations was designated as "formative hardening," and indicated to be the only type of hardening necessarily connected with the slip process. In another detailed picture of work hardening, Mott and Nabarro7 assumed that sufficient dislocations are primarily present in the crystal as a consequence of growth irregularities (mosaic structure) to initiate slip. Work hardening resulted from the interaction of migrating dislocations with localized internal stresses produced during deformation. More recently, however, Mott8 as modified his treatment to include the generation of dislocations at Frank-Read sources and he accounts for the hardening by the formation of sessile dislocations. It has been widely accepted that metals of hexagonal structure, usually possessing only one set of glide planes, exhibit mechanical behavior markedly different from those having cubic structures. However, the differences in behavior of the two classes may be less fundamental than suggested. Rohm and Kochendorfer9 have shown that a single crystal of aluminum subjected to approximately simple shear gives the type of stress-strain curve associated with the hexagonal metals. Similar behavior has been demonstrated for gold and silver crystals by Andrade and Henderson.'" Thus when glide in cubic metals is restricted to one plane, the strain hardening characteristics closely resemble those of the hexagonal metals. It would appear, therefore, that an investigation of some of the strain hardening properties of single crystals sheared in simple glide might provide a more complete understanding of the phenomenon of work hardening. This report relates a number of recent observations made on single crystals of copper, zinc, and cadmium tested in simple shear. In addition, pertinent observations of effects accompanying stress-induced movement of dislocation boundaries are reported. Experimental Procedure and Results Details of the production and advantages of the type of single-crystal shear specimen employed for the following tests have been presented in a previous publication.n The method of testing makes

Jan 1, 1954