Search Documents

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017

By Altemar Dettogne do Nascimento

A Máquina de Lingotamento Contínuo nº 1 da ArcelorMittal Tubarão (AMT), com capacidade nominal de 1,8 milhões de toneladas/ano, teve seu start up em 1995. A máquina é curva com raio de 10,5 m. São produzidas placas de 200, 225 e 250 mm, largura de 800 a 1650 mm e velocidade até 1,7 m/min. Em Abril de 2012, a Máquina parou para uma reforma geral. A empresa Italiana Danieli Davy Distington foi contratada para fornecer a engenharia, fabricação e entrega dos equipamentos no período de 12 meses. No ano anterior à parada da máquina, foi realizado um site survey, o que possibilitou a elaboração de um planejamento detalhado de todas as atividades. A reforma da máquina teve como objetivos principais: correção do alinhamento da máquina, substituição de estruturas oxidadas, implantação de novas tecnologias e redução do tempo de exposição dos operadores a ambientes agressivos (alta temperatura, projeção de aço, queda de cascão da panela e material particulado) através da implantação da sala remota de controle dos veios. A máquina foi colocada em operação em 10 de agosto 2012 após ter completado, sem desvios, as fases de instalação e testes. Este trabalho mostra as fases de desenvolvimento deste projeto, os resultados das tecnologias implantadas e os testes de performance para diferentes famílias de aço.

Jul 29, 2018

By Ramon Fraga Resende

O distribuidor é o último equipamento revestido de refratários em contato com aço líquido e que pode afetar a qualidade do produto. Nesse equipamento, a massa de trabalho é responsável por proteger o revestimento de segurança e evitar a contaminação do aço. Apesar das preocupações em relação ao “pick up” de hidrogênio e consumo de gás, as massas “spray” tem sido uma tecnologia dominante para o revestimento de distribuidor na América do Sul. Nos últimos 20 anos, outras tecnologias entraram no mercado com o objetivo de reduzir a necessidade de água e de gás e aumentar a disponibilidade de distribuidor. Embora essas tecnologias apresentem algumas vantagens, quase 80% das usinas siderúrgicas da América do Sul ainda usam massas “spray”. Isso se deve principalmente aos benefícios como flexibilidade, baixo custo, baixo consumo e alto isolamento térmico. Este trabalho tem o objetivo de discutir as principais vantagens e desvantagens das massas disponíveis no mercado.

Oct 30, 2017

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the ex-service condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 52 to 224 MPa producing rupture times varying from 5 to about 3950h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results obtained on a similar plate of the same material in the virgin condition.

Aug 16, 2017

By Cermets

Ti(C,N)-based cermets offer good high temperature strength, perfect chemical stability, excellent wear resistance, and relativly better machinability. In the present work, the tribological behaviors of Ti(C,N)/SiC sliding pairs lubricated in water and seawater were evaluated using a ball-on-disk tribometer. The experimental results show that a relatively low friction coefficient (about 0.025) can be obtained when lubricated with artificial seawater at the sliding speed of 200 mm/s, while the date is about 0.2 in purified water. The wear surface profiles and the lubricants collected after running-in process for the high/low friction conditions were compared. In addition, the effect of salt molar concentration of the lubricant on the Ti(C,N)/SiC friction properties was investigated. It was found that the smooth and flat surface is the premise to gain the low friction. At the same time, the proper concentration of silica colloid, which is affected by the salt ions, is also an essential one. Moreover, the high sliding speed (200 mm/s) is beneficial to achieve low friction.

Jul 31, 2018

By André Oliveira Galon, Caio Vaccari Silva, Victor Bridi Telles, Raphael Mariano de Souza, Felipe Fardin Grillo, José Roberto de Oliveira

Neste trabalho foi estudada a influência da granulometria de CaO adicionada ao processo de desfosforação, temperatura e teor de FeO da mistura desfosforante na aglomeração de partículas sólidas na escória. Para isto, foram realizados testes laboratoriais em sete condições experimentais distintas, bem como a análise de imagens via software Quantikov, para medir a aglomeração, além de análise termodinâmica computacional. A granulometria, temperatura e porcentagem de FeO se mostraram parâmetros relevantes na aglomeração da escória de desfosforação e a análise de imagens mostrou-se uma ferramenta útil para a obtenção destes resultados.

Oct 1, 2019

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018

By Rodrigo Citrangulo Daniel Luiz

Este trabalho tem como objetivo demonstrar por meio de estudos técnico- científicos e de casos, como foram eliminadas as falhas devido a quebras dos elementos de proteção de sistemas de transmissão de torque (pinos de cisalhamento) no trem Laminador 2 (TL2) da Arcelormittal Piracicaba. A quebra de pinos de cisalhamento no TL2 são uma constante desde o inicio da operação do Laminador 2, sendo que diversas tentativas foram feitas no sentido de eliminar as quebras porem sem sucesso, o que demonstrou a necessidade de uma abordagem metodológica do problema. Este estudo, baseado na analise dos projetos dos equipamentos envolvidos e das praticas de manutenção adotada, orientou o redimensionamento dos elementos de proteção do sistema de transmissão de torque e o desenvolvimento de um novo sistema de proteção, utilizando o drive do motor para fazer a segurança do sistema de transmissão além da revisão e implantação de novas rotinas de manutenção nos equipamentos. O resultado obtido demonstrou a importância do profundo conhecimento tanto do projeto do equipamento quanto da avaliação e conhecimento empírico da manutenção de campo, conjunto este de informações que é indispensável para se garantir o desempenho dos equipamentos permitindo uma produção livre de imprevistos.

Jul 30, 2018

By Débora Cardoso de Oliveira Silveira, Jean-Christophe Huber, Hamzeh Hamadeh, Kateryna Pastel, Guillaume Brosse

The dynamic behavior of oxygen gas flow, determined by the lance nozzle and blow pattern, is a key factor for determining jet efficiency in BOF Steelmaking. The present work compares the performances of Laval and parabolic nozzles with the aid of the Computational Fluid Dynamics (CFD). The Method of Characteristics (MOC) was applied to design a minimum length parabolic nozzle. The results show that the parabolic nozzle generates more uniform and stable jet, with 2% longer potential core and supersonic length and less shock waves. For the parabolic nozzle, the pressure nearby the nozzle wall is higher, which can protect this region from reverse flow of converter gases and offer longer life for the lance tip. Likewise, the flow rate variations would affect less this nozzle. In addition, the nozzle wear was investigated, and the parabolic nozzle has proven relatively less sensitivity to the presence of this deformity.

Oct 1, 2019

By José Adilson de Castro

In the integrated steel industries the sintering process plays an important role furnishing raw material to the blast furnace. In this work, a computational simulation of the sinter process is developed that is able to predict the most important phenomena within the sintering bed. The model is based on the multi phase concept with multiple components described by conservation equations of each component coupled with the momentum, chemical reactions and heat transfer. The model validation was carried out comparing the model predictions with averaged industrial data and local temperature measurements within the sinter strand. The model predictions presented good agreement with the averaged values measured on the industrial sinter process.

Aug 2, 2018

By Pietro Palma

Universal cardan joints are widely used in drivetrains of rolling mills for steel and aluminum making, as well as for non ferrous alloy industry. Working conditions are extremely tough due to high alternating or pulsating rolling torques in the roughing stands and high torques and speeds in the finishing stands. Overloads and lubrication along with oxide and slag are also critical issues that contribute to create severe working conditions. For a constant and reliable power transmission rolling mills performance and uptime rely on Universal cardan Joints which are the most critical equipment of the drivetrain. Fatigue assessment of the most important components of the Universal cardan Joint is therefore definitely vital for the mill in order to avoid failures and consequently downtimes. Considering the component’s dimensions and weight and in addition the time needed in order to reproduce full scale tests, a new approach to study the Universal cardan joint’s main components fatigue behavior has been investigated. It consists in reproducing the local stress condition of the main joint components on small scale specimens that can be tested by conventional laboratory fatigue machines. The aim of this study is to analyze the most critical stress concentration areas in the universal cardan joints highlighting how a universal cardan joint Wöhler curve can be determined through laboratory tests of small scale specimens.

Aug 16, 2017

By Thiago Pires Nagasima

O refino de grão da estrutura bruta de solidificação da liga Cu-30%Zn (latão 70/30) a partir de adições de P e Zr ao banho líquido foi investigado utilizando-se microscopia óptica, microscopia eletrônica e microanálises. Foram conduzidas medidas de tamanho médio de grão pelos métodos planimétrico e do intercepto linear e foram realizadas microanálises por espectroscopia de dispersão de energia (EDS) e de comprimento de onda (WDS). Nas amostras obtidas observa-se que, quando são adicionados P e Zr, sempre ocorre a diminuição do tamanho médio de grão em relação àquele das amostras onde apenas P é adicionado. O menor tamanho médio (? 200 ?m) ocorre para um teor de 0,16% de Zr. O refino de grão coincide com a formação de precipitados geralmente facetados, contendo Zr e P em uma proporção equivalente à da fase ZrP. Sugere-se que as adições causaram a formação de partículas sólidas de ZrP, sobre as quais ocorreu a nucleação heterogênea de grãos da fase Cu-?, resultando no refino de grão.

Oct 30, 2017

By Paula Aliprandini

O licor de lixiviação do minério limonítico tem como foco a recuperação dos metais níquel e cobalto. No entanto, o minério apresenta em sua composição outros metais como o cobre. Este metal não é o foco do beneficiamento, porém tem valor comercial, o que faz com que a recuperação desse metal agrege valor ao tratamento do minério. A técnica de extração por solventes é uma técnica conhecida na hidrometalurgia para recuperação de metais. Para a recuperação de cobre alguns extratantes são conhecidos, como os do tipo hidroximas. Pertencente a essa classe, o extratante Acorga M5640 é usado na extração do cobre. Esse trabalho buscou avaliar o pH de extração do cobre a partir de uma solução sintética baseada no licor de lixiviação do minério limonítico. Foi levada em consideração a solução após o pré-tratamento de remoção do ferro. Além disso, foram avaliadas diferentes concentrações do extratante Acorga M5640 na fase orgânica a fim de avaliar a quantidade necessária para a extração total do cobre sem que houvesse coextração dos demais metais. Foi possível extrair 99% do cobre em solução usando Acorga M5640 na concentração de 5% em volume e pH de trabalho igual a 2..

Oct 30, 2017

By Anivaldo Chevane, Leonardo Xerinda, Rogério Sendela, Andre Vilanculos

Moatize Coal Mine is located in Tete Province, in centre of Mozambique. The deposit contains Gondwana allochthonous coals, and has a large amount of mudstone and siltstone banding. Phosphorus levels in the coal can be high which impacts the use of the coals in steel making where phosphorus is considered a contaminant. The Chipanga seam in the Moatize deposit shows considerable variability, vertically within the seam and laterally across the deposit. The data available from the exploration work indicates that the phosphorus is predominantly present as Apatite but the Crandallite minerals also are significant. The concentration of phosphorus varies with coal particle density with the highest phosphorus levels found for the mid density coal which also shows the highest likely levels of apatite or fluorapatite. Crandallite minerals show higher potential concentrations in the Lower density coal..

Oct 3, 2019

By Tatiane Suelen Santos Silveira, Dagoberto Santos Brandão, Dalila Chaves Sicupira, Graziele Gianini Braga Maria, Marcos Vinícius Fonseca Ferreira, Daniela Barçante Perasoli

O aço inoxidável duplex combina as propriedades mecânicas da ferrita e a resistência à corrosão da austenita, sendo muito utilizado em aplicações industriais que requerem um bom desempenho. Quando submetido a deformações intensas, a austenita transforma-se parcialmente em martensita, aumentando a resistência do aço. Quando o aço é recozido, essa transformação é revertida e a martensita se transforma em austenita, ocasionando um refino de grão do material. Fases secundárias formadas durante o recozimento podem prejudicar suas propriedades mecânicas e corrosivas. Nesse sentido, o objetivo desse trabalho foi avaliar o efeito da temperatura de recozimento na resistência à corrosão do aço inoxidável duplex UNS S32304 laminado a frio. O aço foi submetido à laminação a frio, com deformação de 60%, e posteriormente recozido nas temperaturas de 600°C, 700°C, 800°C e 900°C por um tempo de 0,5 h. A resistência à corrosão foi estudada através da técnica de polarização potenciodinâmica. A laminação a frio promoveu a formação de martensita induzida por deformação (SIM) e a reversão parcial começou a ser observada após recozimento a 600ºC. A ocorrência de SIM promoveu significativa diminuição do potencial de pite e o aumento da temperatura de recozimento aumentou a resistência à corrosão localizada.

Mar 1, 2019

By Pedro Antunes Amaral

Currently there is a constant and essential concern of preserving nature. Over the years the concern with the environment is increasing, new environmental laws are emerging and being applied more rigorously and consequently emerge economic needs and mineral processing practices and other materials. In this sense briquetting becomes an alternative to fine particles agglomeration by means of pressure and or temperature, with the aid or not of a binder, which allows to get a product not only compressed, which presents shape, size, and adequate mechanical properties. The reduction in volume of the material in some cases (beyond the technological benefits) also allows fine materials can be transported and stored more economically, safely and effectively. The production of coke is greater as the content of better coking coal is, thus he low capacity coking coal is not much used in coke ovens. This research aims to demonstrate that briquetting of mineral coals with low coking coal capacity is possible, additionally allows increased coke production, obtaining then a better yield of coke. Basically they take advantage of low price of no coking coals without changing the quality of the coke produced. Anyway, briquetting became a smart alternative to aggregate values, economy and care for the environment.

Oct 30, 2017

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019