Search Documents

By Michel Fillon

Hydrostatic assistance is a commonly used method to improve limited load carrying ability of tilting-pad thrust bearings during transient states of operation of the vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves etc.), it also requires manufacturing of special recesses/pockets at the pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up of the machine and form a hydrostatic film between the pads and the collar. There is a quite wide variety of geometry of recesses (shape, depth, size) met in practical large bearing applications. The presence of a hydrostatic pocket (usually located in the sliding surface above the pivot area, where thin film, high oil pressure and temperature are observed) affects bearing performance under hydrodynamic operation. In theoretical researches, there is an almost common practice not to include hydrostatic recess in THD or TEHD analysis. This is probably due to the problems with obtaining solution for oil film geometry with pocket, with pocket depths order of magnitude larger than gap thickness. In this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of ltaipu power plant. Bearing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket.

Jul 31, 2018

By Verônica Silva Costa Medeiros

O chamote é um resíduo proveniente da indústria cerâmica, classificado como material não-plástico. Tal rejeito pode ser retornado ao processo de produção de cerâmicas, substituindo parte da matéria-prima convencional. O objetivo deste trabalho foi avaliar a incorporação de chamote nas propriedades físicas e mecânicas de peças cerâmicas sob três temperaturas de queima distintas: 850°C, 950°C e 1050°C. As matérias-primas utilizadas na pesquisa foram caracterizadas quanto à granulometria, limites de consistência e composição química por meio de EDX. Foram propostas três misturas, contendo 0%, 13,33% e 40% do resíduo. Corpos de prova prismáticos foram produzidos por prensagem e, após, realizou-se os ensaios de determinação da retração na queima, índice de absorção de água e resistência à flexão. Os resultados revelam que, quanto maior a temperatura, maior a retração linear na queima e a resistência à flexão em todas as misturas. Em relação à absorção, foram observados menores valores a 1050°C, devido ao processo de vitrificação. Verificou-se que a adição de chamote reduz a retração; no entanto, reduz também a resistência mecânica. Dentre as misturas com resíduo, a composição com 13,33% apresentou melhores resultados, sobretudo sob a temperatura de 1050°C.

Oct 30, 2017

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By Flavia de Paula Vitoretti

Pelletizing of iron ore fines is an important process used to produce high quality of raw materials for the subsequent reduction processes in the ironmaking industries. The process involves the production of green pellets and subsequent induration on a traveling grate furnace to promote inner partial melt and agglomeration which confer physical and metallurgical proprieties appropriated to the subsequent reduction processes. The pellets are produced with addition of charcoal to improve efficiency in the reduction processes. The lignin coal from sugarcane straw is an alternative source to replace the charcoal or coke in the self reduction of pellets. This work focused on the influence of biomass on the chemical kinetics parameters inner agglomerate pellet structure under industrial process conditions of the travelling grate furnace due hot gas flows within the pellets.

Aug 1, 2018

By Wilian da Silva Labiapari

Austenitic stainless steels are widely known for their good weldability, excellent mechanical properties for deep drawing and superior corrosion resistance in environments where most of the metals fail. Their uses include many applications subjected to a combination of mechanical and corrosive wear, such as pumps, valves and surgical implants. Although their corrosion resistance has been largely investigated, their resistance to mechanical wear is less studied. In particular, their performance under conditions involving combined corrosive and mechanical wear is not well understood. The aim of this study is to demonstrate the effect of the mechanical component on the electrochemical signal of an anodic polarization curve. A test rig was developed to investigate micro-abrasion-corrosion using a fixed ball configuration. Tests were carried out using stainless steel AISI 304 samples and 25.4 mm zirconia balls as counter bodies. The electrolyte was a 1N H2SO4 solution with SiO2 as abrasive dispersed at the concentration of 10 wt%. The results showed an increase in current density when the counter face roughness and the normal load applied during the tests are increased, evidencing a mechanical influence on the surface activity of this material in a corrosive environment.

Jul 31, 2018

By Rhelman Rossano Urzêdo Queiroz

Amostras de um aço Dual Phase, não deformadas e deformadas à temperatura ambiente e em condições de envelhecimento dinâmico foram examinadas por microscopia eletrônica de transmissão, visando analisar modificações na subestrutura de deslocações na faixa de temperaturas em que ocorre o fenômeno. Observaram-se mudanças significativas no padrão de distribuição das deslocações que evoluiu de uma distribuição uniforme, no material deformado à temperatura ambiente, para uma distribuição em forma de linhas alongadas a 200°C e 300°C, culminando em uma subestrutura complexa com elevada densidade de deslocações a 350°C. A 400°C, a distribuição uniforme foi novamente verificada. As imagens obtidas não indicaram a ocorrência de formação de carbonetos de transição ou precipitação na martensita durante a deformação nas temperaturas em que foram observados os efeitos de envelhecimento dinâmico.

Aug 7, 2018

By Eustaquio Vieira Junior

O Alto-Forno 2 da thyssenkrupp CSA, no Rio de Janeiro, iniciou sua primeira campanha em 16 de dezembro de 2010. No decorrer de sua campanha, verificou-se problemas de deslocamento de staves de ferro fundido, deformação dos staves de cobre e desgaste acentuado do refratário do top cone. Na análise dos eventos adotou-se a inspeção por vídeo endoscopia e em seguida foram tomadas algumas ações para recuperação e preservação do Alto-Forno 2, sendo estendidas também do Alto-Forno 1. Dentre as ações de preservação dos Altos-Fornos destaca-se a projeção robotizada de material refratário, shotcrete, visando reduzir o desgaste acentuado dos staves e deterioração de suas tubulações de refrigeração. O trabalho apresenta o detalhamento das técnicas utilizadas e seleção de materiais assim como os preparativos operacionais que garantiram o bom desempenho do Alto-Forno 2 nos momentos que antecederam a parada e após seu retorno à operação, mostrando que a atividade é viável do ponto de vista técnico e financeiro.

Oct 30, 2017

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017

By Viviane Sardilli Rodrigues

Areia de fundição é utilizada para modelar peças metálicas no setor metalúrgico. Existem vários tipos de areia usadas para essa finalidade que em sua composição possuem desde o quartzo até a areia de zircônio, nas quais o uso de cada uma é dependente da temperatura e do material que será fundido. Um tipo de areia especificamente, a areia de cromita, é utilizada para fabricações de peças feitas a base de aço. Para aglomerar os grãos e construir moldes onde o metal líquido é derramado usa – se resina sintética, comumente a resina fenólica, que é produzida através da reação da reação química entre o fenol e o formaldeído (formol) empregando catalisadores ácidos ou ésteres. A estrutura presente nas resinas são ainda de longe compreendidas. Por se tratar de uma química complexa, poucos estudos são encontrados sobre as alterações na composição após a pirólise e o comportamento da resina perante ao material refratário. Neste trabalho o objetivo foi a identificação dos contaminantes residuais presentes na areia após o processo de fundição, além da caracterização dos metais também existentes no material. Através deste estudo pretendemos identificar os potenciais contaminantes ambientais presentes na areia de fundição para avaliar um possível tratamento através de biorremediação por micro-organismos.

Oct 30, 2017

By Maciej Korecki

Pyrowear®Alloy 53 steel is an excellent material for the construction of drive transmission components (gears, shafts, etc.) which have to operate in difficult conditions primarily in the aviation industry (Fig. 1.). Among the properties of such items is a high case hardness and abrasion-resistance, while the core remains flexible and is capable of carrying large impact loads. They can work at elevated temperatures with limited lubrication. The thermal treatment of such materials is based on case hardening by means of carburizing. This paper presents the technology of vacuum carburizing of Pyrowear® Alloy 53 steel. It discusses the methods of establishing different profiles of carbon concentration in a layer and their influence on the hardness profile. The effects of sub-zero treatment and tempering on the properties of the hardened case are also considered. It also presents a SimVaC® simulator of vacuum carburizing, designed especially for Pyrowear® Alloy 53 steel, which provides highly accurate predictions of the outcome of the process as the profile of carbon concentration in the layer, or vice versa: establishes the process parameters which will guarantee the required profile.

Aug 16, 2017

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Ana Flávia Tardin Siviero

A “Terra de Sucata” é o coproduto gerado pelo processo de beneficiamento de sucata na indústria siderúrgica. Atualmente, a aplicação desse coproduto é limitada pela falta de uma caracterização completa do mesmo. Dessa forma, o presente trabalho visa à caracterização de tal material para viabilizar o levantamento das possibilidades de aproveitamento do mesmo. A amostragem foi feita em uma usina siderúrgica localizada na cidade de Cariacica, no Espírito Santo. Foram realizadas análises via Difração de Raios-X (DRX) e Microscopia Eletrônica de Varredura acoplada à Espectroscopia de Energia Dispersiva (MEV/EDS). Além disso, foram feitas a determinação de pH, distribuição granulométrica, teor de umidade, densidade e análise elementar. A partir desses experimentos, observou-se que se trata de um material bastante heterogêneo em termos de morfologia, composição e granulometria, o qual apresenta 6,43 ± 0,15 de pH, 4,53% ± 0,92% de teor de umidade e 2,25 g/cm³ ± 0,25 g/cm³ de densidade. Esse material é composto pelos elementos ferro, alumínio, silício, cálcio, zinco, magnésio, manganês, fósforo, enxofre, carbono, titânio, potássio e sódio. A partir da análise de DRX, foi possível identificar a presença das fases quartzo, hematita, calcita, óxido de ferro (II) e outras.

Oct 30, 2017

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Larissa Agrizzi Ronqueti

The effect of coiling temperature on selective oxidation behaviour of binary and ternary iron-based model alloys containing different contents of Si or Mn were investigated by SEM and SIMS. The experiments were carried out with a temperature ranging from 450 °C to 700 °C, under N2-5%H2 gas flow with a Dew Point of -3.3°C, for different durations. SEM images of binary iron-based model alloys revealed a decrease of grain boundary oxidation depth with increasing Silicon or Manganese content. At 530°C and 600°C SIMS results showed no Silicon diffusion toward surface, contrary to the results analyzed for Fe-x%Mn. Tests results and Wagner’s theory application (specific cases Fe-0.2%Si and Fe-0.5%Si) showed that grain boundary oxygen diffusion coefficient “DoGB” is almost 60 to 70 times faster than oxygen bulk diffusion coefficient. These results helped to broaden knowledge of single-element effects on grain boundary oxidation, in addition, will contribute of the future works in new steels with complex alloy compositions.

Aug 17, 2017

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

This article is based on a bibliographical review of a field work that was done in the Salina São Camilo in the region of Mossoró - RN. The general objective of this research is to present the main exploratory and beneficiation aspects of salt production. Among the aspects of salt is the properties of salt, history and mining, besides the aspects of environment and work safety. However, this research resulted in preliminary data, but it would be interesting to be more thorough so that the extraction of salt in the academic world is disclosed

Oct 3, 2019

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017