Search Documents

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Márcio Corrêa de Carvalho

Welded deposited chromium carbide overlay’s has been widely used in various branches of welding overlay’s industry related to wear. Characterization techniques are an important tool in the development of chromium carbide overlays resistant to wear, enabling the identification of phases, constituents and defects. In this work one used optical microscopy, scanning electron microscopy and energy dispersive spectroscopy on chromium carbide overlay’s deposited by submerged arc welding process. The characterization techniques identified precisely the elements of the overlay’s enabling point of the main cause of the observed defects such as cracks, porosity and clusters of particles known in the industry as " rice crispy" .

Aug 16, 2017

By Emanuelle Garcia Reis, Gustavo de Sousa, Rodney Pardo Alves

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. In general, national and international plate markets are every day more rigorous about final product quality. Suppliers must be aware about dimensional accuracy, surface quality and flatness of the plates, independent of the quality standards. To guarantee the best service to this increasingly demanding and competitive market, it is extremely important to guarantee the original project conditions executing the right maintenance of the rolling mill main components. In order to maintain the product quality and avoid the production and maintenance cost increase, it is important to find ways to control the mill and the main process variables, through daily measurements of the equipment performance. This paper aims to present the influence of the main equipment variables that affect the mill operational stability and how to control and evaluate the mill performance.

Oct 1, 2019

By Luiz Bruno de Oliveira Araujo, Luciano Morais Teixeira, Luiz Gustavo Pedrosa de Melo, Altair Lúcio de Souza

The off-line simulation of the metallurgical process in an industrial line brings several benefits such as: evaluation of the influence of the main parameters that affect the results of the process, comparison between different set ups, greater assertiveness in operational adjustments, process optimization and reduction tests for development of new products. With this objective, a software for offline simulation of the hot strip mill process of Gerdau Ouro Branco was developed based on the logic of calculations implemented in the online model. The software results in important process variables such as mill pass scale, load, torque, and power at each pass, temperature and the hot mean flow stress of the simulated material. During rolling mill process the strip presents different temperatures and time between passes for different points along the length, which directly influences the hot strength of the product and consequently in the calculated variables, thus the calculations executed by the software were divided to three points of the strip, head, body and tail bringing the individual results to each of these positions.

Oct 1, 2019

By Jose M. Rodriguez-Ibabe, Beatriz Pereda, Beatriz Lopez, Felipe Bastos

The modeling of austenite evolution during the hot rolling of steels is covered in the literature for a wide range of chemical compositions, although mainly for carbon contents below 0.20%. In addition, most research on this topic is oriented for processes that are characteristic of flat products. Compared to those processes, the hot rolling of bars for structural applications presents considerable particularities concerning mainly deformation, rolling speed and rolling temperature profile. Those particularities result in considerable changes on process parameters that affect the austenite microstructure evolution, both in the softening and hardening mechanisms if microalloying elements such as Nb is present. The aim of this work was to develop a model to predict the evolution of austenite microstructure that is suitable for the hot rolling of structural reinforcing bars. Different torsion tests simulating industrial schedules particular from those type of processes were performed. The tests showed the need to investigate Nb strain-induced precipitation interaction with softening mechanisms that can occur during the deformation schedule. At the end, the new proposed kinetics and routines were introduced to a program, MicroSim-Bars®, that is able to model austenite evolution under structural bar hot rolling conditions.

Oct 1, 2019

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Jürgen Schanderl

Cold rolling mills by SMS Siemag are well known for their reliability and long-life cycle. They are an investment in the future. Nowadays mill owners are under considerable competitive pressure and are asked to organize production in a more and more efficient and flexible way. Doing so, a number of elevating screws have to be turned. These are: cutting of operation costs, especially by more efficient equipment and processes as well as transition to more process flexibility to fulfil future product requirements. To support owners in their effort, SMS Siemag offers convincing solutions in cold rolling technology under the brand X-Roll 2.0. Examples to be presented are: Sieflex®-HT drive technology; Redesigned DS system; New reel design: Twin Reel; Emulsion compact unit ECU Compact; TRC® threading assistance system; ECOMode and Energy ADVISOR monitoring system.

Jul 30, 2018

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Wolfgang Kern

More and more coke oven plants worldwide face the task to improve their emission reduction at their coke oven batteries. In the 90’s PROven® was invented and developed by DMT to regulate the inner pressure of a single coke oven chamber. Generally, most of the coke oven chambers can only close and open their connection to the collecting main but without the possibility to regulate the pressure during the carbonization time. Through the installation of PROven® the load on the coke oven door sealing system and the charging lids will be decreased and so does the emissions of crude COG as well. The current PROven® system, installed in the collecting main, does not only regulate the chamber pressure, it replaces the valve between the goose neck and the collecting main, too. This variable pressure control allows decreasing the leakages at the emissions sources to a minimum and allows operating the collecting main under optimum pressure. Subsequently, this will lead to enhanced emission reduction. PROven® proved its value with more than 2,100 units installed by licensee worldwide. Nevertheless, DMT is always focused on its client’s needs and therefore enhance PROven® to provide the Best Available Technique (BAT). Among the main features of the now available system is the plain arrangement with a higher reliability and the possibility to install the system outside of the collecting main without modifying it. Hence, upgrading coke oven plants during operation is possible without any noticeable impact on the plant operation.

Aug 1, 2018

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Eric Yoshimitsu Sako

One of the main difficulties in the operation of trough and runners at Arcelor Mittal Tubarão (AMT) Blast-furnace no.02 is the reduced amount of time available for repair procedures. The consequence is that the castable installation must often be performed during hot conditions and the installed castable could easily detach from the base material during the early stage of operation, exposing the previously oxidized base material to molten iron and corrosive slag attack. When events like this happen, emergency repairs must be executed, resulting in increased refractory unit consumption and an unplanned shutdown of unit operation. Considering these targets, Nippon Crucible Co. and Saint-Gobain HPR Brazil have developed a high-performance Al2O3-SiC-C composition based on an entirely novel anti-oxidation technology. Oxidizing reactions could be attenuated by adding an oxidant inhibitor and a water reducing agent. As a result, the open porosity was significantly reduced, resulting in an improvement of campaign life in terms of pig iron throughput when compared with the regular castable. An analysis of this life improvement showed successful results for the material after 250 days of campaign. The main reason for such successful results was that the deterioration caused by the oxidation was significantly less and that this change made on the high cohesive structure of the base material was maintained for a long time. The attained results allowed Arcelor Mittal Tubarão to achieve longer trough campaigns, and avoid any unplanned stoppages with zero breakdown risks.

Oct 30, 2017

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Leonardo de Souza Melo, Giovani Rodrigues, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipment in 2015. In addition to improving productivity related to these new equipment, several additional jobs were planned and executed on equipment already installed has been carried out in order to improve the efficiency of the line. The present work exposes what was done in the scale breaker (tension leveler) to improve the availability results of the section and consequently of the line.

Oct 1, 2019

By Silvio Cecchini

State-of-the Art Mould Level Control Solutions for continuous casting applications face different challenges. On the one hand, technological phenomena such as clogging and unclogging, unsteady bulging or waving can create unpredicted meniscus disturbances by completely changing the casting channel geometry and the flow behaviour of liquid steel to the mould. On the other hand, from the viewpoint of caster operations, long lifetime, quick interchange-ability and integration capability into existing systems must be achieved. In the present contribution, the overall development of INTECO TBR’s mould level master – a comprehensive mould level control solution for all continuous casting applications – will be introduced. The basis for the presented system is a development over several years which includes investigations of all critical components such as shroud, stopper, stopper mechanism, servo actuator and mould level control program. These investigations finally resulted in a new-ly developed control algorithm for a highly dynamic servo actuator. The control algorithm with its basic functionality such as the prevention, identification and removal of clogging impacts with the associated automation functions to reduce their influence onto the overall mould level control performance will be presented. The scientific basis, the resulting control functions and their related automation implementation will also be illustrated. Finally, a patented control algorithm and control functionality for unsteady bulging and waving effects with the associated automation functions to reduce their influence onto the overall mould level control performance.

Aug 16, 2017

By Dalila Chaves Sicupira

A pitting corrosion study of welded joints of lean duplex stainless steel (LDSS) UNS S32304 has been performed. LDSS S32304 thick plates were welded by different processes commonly employed in equipment and piping construction: SMAW (Shielded metal arc welding), GMAW (Gas metal arc welding) and FCAW (Flux cored arc welding). The electrochemical behavior of different weldment zones (fusion zone (FZ), base metal (BM) and heat affected zone (HAZ)) was characterized both independently using an electrochemical microcell and together through whole sample analysis. The electrochemical method applied was performed in acidified glycerin, a process fluid of the biodiesel industry. The results were correlated to the microstructural features of the materials. Based on the results, is possible to conclude that the breakdown potential (Eb) of the fusion zone (FZ) was higher than the Eb obtained for the heat affected zone (HAZ). In general, top samples show higher breakdown potential than root samples and also the samples welded using filler metal 2209 has a better anodic behavior than the filler metal 2307. According to the results, GMAW welding process with 2209 as filler metal was revealed as the optimum chosen for application of 2304 duplex stainless steels in this case.

Jan 16, 2018

By Hiroshi Ichikawa

In 2013, Nippon Steel & Sumikin Engineering Co., Ltd. (hereafter referred to as NSENGI), Tenova HYL and Danieli have entered into an agreement to combine ENERGION DR technology into blast furnace technology and/or with syngas technologies. This new alliance will allow the three companies to combine research and development activities with their respective expertise in ENERGIRON DR technology, Blast Furnace technology and Syngas (by-pro gas and coal gasification) technology, with the ultimate objective to develop breakthrough iron making technologies and create such EPC projects. This paper introduces the concepts and the features of our breakthrough technologies of combining of ENERGIRON DR technology, Blast Furnace technology and Syngas technology.

Aug 16, 2017

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Florian Markus Penz

The increase in Basic Oxygen Furnace (BOF) plants in steelmaking has given rise to renewed interest in a dynamic simulation of the BOF process. Material and process costs can be saved with optimized process times and targeted charging of scrap and slag formers. Beside hot metal, scrap is the main source of iron in the BOF process. Furthermore, scrap is used as a coolant during the process due to exothermal chemical reactions occurring in the BOF. In this paper, the melting and dissolution behaviour of scrap in the BOF process is discussed. A new dynamic thermodynamic and kinetic Matlab® model used to simulate scrap melting behaviour as a function of various scrap surface parameters and particle size is presented, as well as the influence of scrap properties on liquid bath temperature and final crude steel composition after a defined blowing period.

Oct 30, 2017