Search Documents

By Joseph T. Singewald

The term "titaniferous magnetite" is used to designate those magnetic ores of iron that carry more than 2 or 3 per cent of titanium. Large and easily workable deposits of these ores occur in different parts of the world, and have attracted attention for many years. Under present furnace practice, however, the smelting of these ores is both difficult and expensive, and for that reason they are not accepted by furnaces, so that the deposits are practically worthless. The problem of finding a feasible method of utilizing these ores has naturally been attractive, and numerous attempts have been made to solve it. Experiments to that end embrace two lines of investigation. The one that has been the more frequently tried is the elimination of the titanium from the ores, so as to make possible their smelting in the usual way. The other is the devising of a method of smelting by which titaniferous ores may be reduced as economically as are non-titaniferous ores. The former method involves a physical process, the latter a chemical process.

Jan 1, 1913

By B K. Hebblewhite, F T. Suorineni, J D. Tibbett

Block caving is an underground mining method that can provide high production capacities at low operating costs. This enables the profitable extraction of massive, low-grade orebodies and attracts industry towards the method. Block caving operations require significant initial capital investment and predictable cave propagation is crucial to safety and economic success. Lack of access to observe the caving process hinders our ability to learn how the rock mass and geological structures are reacting to mining. Virtual reality scientific visualisation (VRSV) enables the integration and investigation of multiple, large caving data sets and provides a viable alternative to visualise rock mass response without physical access to the cave. Point instrumentation is incapable of providing an overview of cave performance and seismic monitoring, while providing an overview of the rock mass and the response of structures to caving, is only useful when linked to the caving activities. The integration of point instrumentation data with seismic monitoring information, coupled with scientific visualisation of the mining system in a virtual reality environment, provides a powerful means for understanding caving performance.This paper describes the use of a VRSV module at UNSW Australia, designed for investigating the block cave mining system from a case study operation. This module has been used to investigate the location and chronological evolution of seismicity to understand sources of damage resulting in seismic space-time sequences (SSTS) in the caving system. The events within an SSTS represent damage that is spatially and temporally related. An SSTS group represents a collection of microseismic events from a reasonably competent region of the rock mass that has experienced a stress change significant enough to cause sequential damage. SSTS group locations have been seen to be the path of subsequent cave propagation. Thus, SSTS analysis enables insight to further our understanding of rock mass damage in caving geomechanics through analysis of historic data. Such insight has operational potential to learn from recent rock mass activity for optimising the management of undercut advance, draw front advance and cave draw patterns.CITATION:Tibbett, J D, Suorineni, F T and Hebblewhite, B K, 2016. Understanding damage source mechanisms in a caving system using virtual reality scientific visualisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 439–452 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Holger Cordes

X-ray diffraction has long been used for qualitative and quantitative mineral analysis but Rietveld data analysis is still an under utilized method for mineral exploration and processing applications. In this full-profile approach the structural parameters of each mineral phase, together with experimental parameters, are refined by least-squares methods to minimize the difference between observed and calculated diffraction patterns. The result is a standard-less, quantitative analysis of the mineral abundance in the sample that is more accurate and considerably faster compared to traditional methods. The TOPAS software package combines a user-friendly interface with a unique approach to resolve overlapping peaks. Automated analysis options are also available and significantly reduce analysis time for routine samples. Several examples on a wide range of naturally occurring rock types are shown that illustrate the capabilities and limitations of the method. The examples include several options for the quantification of amorphous constituents like volcanic glasses.

Jan 1, 2006

By Carl Tom Blevins

Resin was first introduced to U. S. mines in 1971 and first produced in 1973. The original polyester roof bolt resin was very expensive and limited to a single cartridge size and a single slow gel time. Early resin applications were limited to very difficult ground conditions. Today approximately 80% of the over 100 million roof bolts installed in U.S. mines, tunnels, and construction projects employ polyester roof bolt resin. The industry has evolved from hand packing samples for trial testing to producing enough resin, if converted to a .9 inch (22.9mm) diameter cartridge, to encircle the world at the equator approximately three (3) times each year. Manufacturing and design improvements allow for a more consistent product with a wide range of applications at a price that is approximately 30% below our 1974 sales price. An inflation adjusted dollar buys six (6) times more resin in 2006 than in 1974. Modern gel times range from a few seconds to over 15 minutes. Viscosity is matched to bolt type and drilling machine characteristics. Multiple cartridge diameters and a wide range of cartridge lengths are offered by two operating companies. Resin manufacturers have also gone through a period of restructuring and change to meet the challenges of the mining industry. DuPont Fasloc has become Fasloc, Inc., a stand-alone company. Celtite became Fosroc then Minova, as it is known today. During this transformation, several manufacturers have either discontinued production or were absorbed. The industry led the development of the chemical grouting materials specifications contained in ASTM F432-95, Standard Specifications for Roof and Rock Bolts and Accessories. A history of the industry will be presented within a discussion of the evolution of the strength index, speed index, cartridge volume, class designation, and product marking requirements of ASTM F432-95.

Jan 1, 2006

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

Project approvals are the key mechanism to balance the environmental, social and economic aspects of a project. The assessment approaches vary significantly between states, with some having a strong emphasis on social, economic and environment, while others focus primarily on the environmental issues. There are a number of approaches which proponents and governments should consider which not only deliver better project outcomes, but can save proponents time and resources in delivering the project.   These approaches are not new but are often poorly implemented. This paper considers a number of these approaches and outlines the benefits they bring.

Jun 1, 2010

By P. S. Pashkovsky, S. N. Smolanov

The essence of the method consists in creation of drop of opposite sign at the isolating stoppings, by which air losses through the accident district change direction of their motion. The period of reversal is selected in that way so that air may not find itself in the zone of burning. The method of fighting the fire considered was repeatedly used in the coal mines of the Ukraine. The theoretical basis of efficiency and two examples of use of this method by fighting the underground fires are adduced in the paper.

Jan 1, 2003

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By B Mohanty, G Ludwig

A thorough assessment of development drilling and blasting practice was carried out at two underground mines at INCO operations in Thompson, Manitoba. The study showed that significant improvement in productivity can be achieved through careful selection of explosives and loading practice, and modifications of the standard blast lay-out. The analysis involved assessment of the effectiveness of various perimeter blasting methods, employing selected explosives and loading practice in both jumbo and jack-leg rounds. The blasting pattern as well as burden and spacing were varied to determine their effect on the blast results. The various types of explosives used were, pneumatically loaded ANFO, with and without detonating cord tracing, extra-strength detonating cord, and slurry and emulsion explosives with and without cord tracing. The study also dealt with various means to achieve increased rate of advance in both jumbo and jack-leg rounds. The diagnostic measurements consisted of VOD, 'burn' marks or half-barrels on perimeter wall, and blasting vibrations. The effects of geology, firing sequence, blast lay-out, and drill hole deviation on the final results were also examined. The results of the study have been shown to have very important bearing on the design of development round blasting.

Jan 1, 1998

Cokriging uses a sparsely sampled, but accurate and precise primary dataset, together with a more abundant secondary data-set, for example grades in a polymetallic orebody, containing both error and bias, to provide improved results compared to estimation with the primary data alone, as well as filtering the error and mitigating the effects of conditional bias. The method described here may also be applied in polymetallic orebodies and in other cases where the primary and secondary data could be collocated, and one of the data-sets need not be biased, unreliable, etc. An artificially created reference data-set of 512 lognormally distributed precious metal grades sampled at 25×25 m intervals constitutes the primary data-set. A secondary data-set on a 10×10 m grid comprising 3200 samples drawn from the reference data-set includes 30 per cent error and 1.5 multiplicative bias on each measurement. The primary and secondary non-collocated data-sets are statistically described and compared to the reference data-set. Variograms based on the primary data-set are modelled and used in the kriging of 10×10 m blocks using the 25×25 m and 50×50 m data grids for comparison against the results of the cokriged estimation. A linear model of coregionalization (LMC) is established using the primary and secondary data-sets and cokriging using both data-sets is shown to be a significant improvement over kriging with the primary data-set alone. The effects of the error and bias are filtered and removed during the cokriging estimation procedure. Thus cokriging using the more abundant secondary data, even though it contains error and bias, significantly improves the estimation of recoverable reserves.

Jan 1, 2014

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By R Edwards

Greater efficiency of capture of minus 6 mm to fine micron size particles of free gold is achieved with the Knelson Concentrator. The development, principles of operation and recent innovations relating to this enhanced gravity concentrating device are described by the inventor, followed by a description of application and consequent economic benefits in low grade alluvial gold deposits by a large scale user of Knelson Concentrators in the Northern Territory of Australia.

Jan 1, 1990

By H. O. Hofman

At the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper-Smelting,"' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, FeS. They arrived at this inference from the observed fact that a matte containing Cu,S, 90.4, and FcS, 9.6 per cent. (or, in round figures, Cu2S, 90, and FeS, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent. of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent. of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples gave them a grayish-black field of very uniform appearance, except that five of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the ferrous sulphide-cuprous sulphide series, and to see how the constitution could be further revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, " The Concentration of Gold and Silver in Iron-Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1908

By X. S. Yuan

With the production increase of Oil Sand in Fort McMurray Alberta, more efficient tailings disposal has become a priority for Syncrude Canada Ltd. A lot of work on tailings research and development has been compiled to determine the most effective deposition to increase reclamation options, water re-use and thermal energy recovery. Efficient flocculation of fine oil sand tailings is the key technology for thickening. It was identified that flocculation of fine transition/marine ore tailings using a single flocculant was not effective. The thickener overflow contains 1-4% solids content compared with the target solids content of <0.5% obtained with Estuarine ore. As a result, novel processes for treatment of fine transition/marine ore tailings have been developed at Syncrude Bitumen Production Development since June 2004. While the conventional processes using a single flocculant, a single coagulation, or a coagulant-flocculant combination was ineffective for transition and marine ore tailings, the new processes including Coagulation-Flocculation-Coagulation (CFC), Flocculation-Coagulation (FC) and Flocculation-Coagulation-Flocculation (FCF) were acceptable options. The key components of these technologies consist of the recipe of chemicals and their adding sequence. With these technologies, almost all sub-micron clay minerals are aggregated together and settle as a whole, resulting in a clear supernatant of less than 0.1% solids.

Jan 1, 2006

By W. L. Brien, O&apos

Molybdenum alloys with good strength properties at elevated temperatures were produced by the powder metallurgical internal oxidation method previously applied to tungsten and known as oxyreaction strengthening. Commercial molybdenum powders were blended with 0 to 10 pet of a reactive powder, ZrMo2. The effects of composition, blending procedure, and sintering conditions on strength properties at elevated temperatures were studied. Strengthening was attributed to zirconium in solid solution with molybdenum and to the presence of submicrometer particles of Zr02. Several alloys had tensile strength and stress-rupture properties com-parable with those of the best commercial alloys. The maximum tensile strengths obtained were 92 kpsi at 1,200° C and 53 kpsi at 1,316° C. The maximum stress-rupture life at 30 kpsi and 1,200° C was 145 hours.

Jan 1, 1974

By Paul S. Goodman

This report examines absenteeism and accidents. The first section provides some background information on absenteeism. The second section examines trends in absenteeism in underground coal mines over time. The third section examines causes of absenteeism. Models were examined. The first model looks at self-report reasons for absenteeism. The second examines demographic correlates of absenteeism. The third model includes demographic and attitudinal predictors of absenteeism. The next section of the report examines the effect of absenteeism on accidents. The last section contains strategies for reducing absenteeism.

Jan 1, 1985

By S C. Labram, A Stabile

"Modern train load out stations are becoming faster and have the ability to load a 100 wagon train in less than three hours. At 70 metric tonnes per wagon, that is an average fill rate of 2333 t/h and considering the train is continuously moving, the instantaneous feed rate into the wagon is in the region of 4200 t/h.The main feed conveyor that maintains the level in the surge hopper, above the final weigh hopper, operates in excess of 5000 t/h to ensure uninterrupted charging of the weigh hopper to not disrupt the train loading operation.To avoid demurrage costs (a charge by the Rail Operating Company for exceeding the contractually agreed loading time) the train has to be handled speedily and efficiently and spend the absolute minimum time at the loading facility. Everything else has a much lower priority, including sampling.Thermo Fisher Scientific’s brief was an engineering, procurement and construction management (EPCM) contract to provide a sampling scheme adjacent to the prepurchased and predesigned load-out facility, but which interfaced seamlessly with the loading system of the trains and provided the following: an instantaneous particle size distribution (PSD) result for each truck loaded, and a final PSD for the total train prior to the train leaving the loading facility a crushed (-3 mm) composite sample for chemical analysis for the whole train a composite physical analysis sample for the whole train.The design presented some interesting challenges to our team, but the end result is a system that not only ‘stands alone’ but interfaces seamlessly with the loading system. This paper discusses the design itself and potential improvements to future systems.CITATION:Labram, S C and Stabile, A, 2017. An automatic sampling methodology to determine contractual particle size distribution in rapid train load out stations, in Proceedings Eighth World Conference on Sampling and Blending, pp 229–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By O. F. Oxtoby, J. E. Olsen, M. W. Erwee, Q. G. Reynolds

"The extraction of molten products and wastes through smelting furnace tap-holes during the tapping process is a complex procedure involving many coupled thermophysical effects. Insight into the fluid flow behaviour in such systems can be gained by using computational mechanics tools to build highfidelity models of the fluid flow and other relevant physics. Previous work using such models indicates that the nature of the flow in the tap-hole, as well as operational parameters such as the tapping flow rate, depends strongly on the properties of the material being tapped and the geometry of the tap-hole channel. Additional complications arise when multiple fluid phases (for example, slag and metal) are present simultaneously, when porous coke beds hinder flow to the tap-hole entrance, and when the geometry of the tap-hole changes over time due to cycles of wear and repair. In the present work, challenges with the coupling of phenomena such as multiphase flow and porosity into computational fluid dynamics methods for tap-hole modelling are discussed in the context of electric furnaces used for ferromanganese production. Qualitative and quantitative results of computational models of flow through tap-holes are presented and compared as a function of material parameters to determine sensitivity effects, and in response to operational parameters to determine typical process behaviour over the duration of a tap. IntroductionPyrometallurgical production using electric furnaces accounts for substantial portion of the world supply of ferroalloys and other strategic materials (Degel et al., 2015). A range of different furnace designs may be used depending on the metallurgical process, with circular three-electrode submerged arc furnaces (SAFs) powered by alternating current being the most common for commodities such as ferromanganese and silicomanganese (Olsen, Tangstad, and Lindstad, 2007).As shown in Figure 1, manganese furnaces typically operate with a deep charge consisting of an upper layer of loose burden (onto the upper surface of which is fed solid raw material), a molten slag layer partially or completely filled with unreacted carbonaceous reductant (generally metallurgical coke), and a molten metal layer which settles to the bottom of the furnace due to its high density. The solid particles present in the slag and burden layers form porous beds which hinder the fluid flow of molten process material and gases inside the furnace (Olsen, Tangstad, and Lindstad, 2007).In order to remove material from the furnace during normal operations, a single tap-hole is built into the sidewall of the vessel near to the level of the hearth. Tapping involves removing both slag and metal phases through the same tap-hole channel, which makes tap-hole design, operation, and maintenance particularly complex. In the case of processes such as ferromanganese, which operate with no external gas injection or open arcs present at the furnace electrodes, flow of material out of the tap-hole is driven primarily by the hydrostatic pressure generated by the weight of the solid and liquid phases above the tap-hole."

Jun 1, 2019